Professional Documents
Culture Documents
55LW56000
LED Backlights
LCD-DV Troubleshooting 55" Class 1080P 120Hz LED TV SmartTV (54.6" diagonally)
OUTLINE
Preliminary Section: y Contact Information, Preliminary Matters, LCD Overview, General Troubleshooting Steps Product Information Section: Specifications Menu Information Specifications, Cinema 3D Section: Screen design and theory Disassembly Section: Removal of Circuit Boards Troubleshooting Section: Board Operation Troubleshooting of : Switch Mode Power Supply with LED Backlight Driver Main Board T CON (TFT Panel Driver Board) T-CON Front IR/Intelligent/Soft Touch Key Board Speaker
2 July 201 LCD TV 1 55LW56000
At the end of this Section the Technician should be able to Identify the Circuit Boards f S f C and have the ability and knowledge necessary to safely remove and replace any Circuit Board or Assembly.
55LW56000
CAUTION
To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for g purposes, disconnect the p , power immediately after p y performing the necessary checks. Also be g y diagnosis or test p p aware that many household products present a weight hazard. At least two people should be involved in the installation or servicing of such devices. Failure to consider the weight of an product could result in physical injury.
55LW56000
ESD Notice
Todays sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage the electronics in a manner that renders them inoperative or reduces the time until their next failure. Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively, you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before removing a replacement part from its package, touch the anti static bag to a ground connection point or anti-static unpainted metal in the product. Handle the electronic control assembly by its edges only. When repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.
Regulatory Information l f
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to g provide reasonable p protection against harmful g Part 15 of the FCC Rules. These limits are designed to p interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction manual, July cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is reception, on, encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and the receiver; Connect the equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the dealer or an experienced radio/TV technician for help.
55LW56000
LG Contact Information
Customer Service (and Part Sales) (800) 243-0000 Technical Support (and Part Sales) (800) 847-7597 USA Website (GSFS) Customer Service Website Knowledgebase Website LG Web Training LG CS Learning Academy http://gsfs-america.lge.com p g http://www.us.lgservice.com http://lgtechassist.com https://lge.webex.com http://ln.lge.com/ilearn
New: 2010/11 Wireless Ready Models Software Downloads Presentations with Audio/Video and Screen Notations
http://136.166.4.200
Training Manuals, Schematics with Navigational Bookmarks, Start-Up Sequence, Owners Guides, Interconnect Diagrams, Dimensions, Connector IDs, Product Pictures and Features. Also available on the Plasma Page: PDP Panel Alignment Handbook, Plasma Control Board ROM Update (Jig required) Pl C t lB d U d t (Ji i d)
Published July 2011 by LG Technical Support and Training LG Electronics Alabama Inc Alabama, Inc. 201 James Record Road, Huntsville, AL, 35813.
55LW56000
55LW56000
55LW56000
IS IT A TV? OR SOMETHING BETTER? Welcome to the third dimension! The LW5600 delivers LG Cinema 3D technology and a whole lot more. It lets you tap into the virtually limitless entertainment capabilities of LG Smart TV and enjoy better picture quality with LG's LED Plus display technology technology.
55LW56000
Media Box
Audio only to TV (TV audio can not be heard via Optical Audio Out on Media Box). Not 3D Ready
Audio/Video is only sent to the TV, not from the TV to the Media Box.
Wireless Receiver/Transmitter Wi l R i /T itt Dongle Attaches via Velcro to the back of the set HDMI
10
55LW56000
AP (Wireless Router)
Modem
1 1
55LW56000
Basic Specifications
LG Smart TV1 LG Cinema 3D2 2D to 3D Conversion
Key TV Features
1
LED Plus w/Local Dimming TruMotion 120Hz Wi-Fi Ready (Adapter Included) Magic Motion Remote (Included) Full HD 1080p Resolution DLNA Certified ENERGY STAR Qualified Picture Wizard II Intelligent Sensor Smart Energy Saving ISF ISFccc Ready R d
12
Internet connection & subscriptions required and sold separately. The Magic Motion Remote does not come equipped with all LG Smart TV enabled TVs and a separate purchase maybe required. The Hulu Plus service is projected to be available via a firmware update in July 2011. The LG web browser does not support Flash 10 or HTML 5, therefore, access to certain web content July be limited or unavailable.
For a small percentage of the population, the viewing of stereoscopic 3D video technology may cause discomfort such as headaches, dizziness or nausea. If you experience any symptoms, discontinue using the 3D functionality and contact your health care provider. 4 Pairs of 3D glasses are included.
55LW56000
Want 3D like you get it in the movie theater? Lightweight glasses, wider viewing angles and with clear 3D images? LG's Cinema 3D experience can bring it right to your home. Enjoy amazing depth along with smoother, crisper images, and a clear picture from virtually any angle.
LED Plus
Want deeper blacks and richer colors? LGs LED Plus technology provides even greater control of brightness through local dimming technology to deliver better contrast, amazing clarity and color detail, as well as greater energy efficiency compared to conventional LCD TVs.
LG SmartTV
A revolutionary, easy way to access virtually limitless content, thousands of movies, customizable apps, videos and browse the web all organized in a simple to use interface interface.
Magic Motion Remote (Included) Just point and choose selections with LG's unique motion-controlled Magic Remote. Remote
13
55LW56000
14
55LW56000
15
55LW56000
Parts List and Owners Manual list a p/n AKB72914043. It has the same buttons, but some may be in different locations.
16
55LW56000
USB1 or USB2 for Software Upgrades, Music, Videos and Photos. Also for the Wireless Network adaptor. p
Wireless Media Box Remote Jack AV/Component In AV/Component In Antenna In HDMI 4 HDMI 3 RS232 In HDMI 2 HDMI 1
LAN
RGB
RGB Audio
Optical Out
Head Phones
17
55LW56000
Highlight Check Update Version g g p to see if an update is available. Scroll up to highlight ON and cursor right to turn off automatic Software Update. p
18
55LW56000
2) Copy new software (xxx epk) to "LG DTV" (xxx.epk) LG_DTV folder. Make sure to have correct software file. 3) With TV turned on, insert USB flash drive. 4) The TV Software Upgrade screen appears. (See figure to right) 5) Cursor left and highlight "START" Button and push Enter button using the remote control. 6) You can see the download progress Bar. 7) D not unplug until unit h automatically Do t l til it has t ti ll restarted. 8) When download is completed, you will see COMPLETE. 9) Your TV will be restarted automatically.
Currently Installed Version Software Version found on the USB Flash Drive File found on the USB Flash D i Fl h Drive
* CAUTION: Do not remove AC power or the th USB Flash Drive. Do not Fl h D i D t turn off Power, during the upgrade process. Highlight Start Press Select
19
55LW56000
File shown is not correct for this model. Scroll down and highlight Options Options WARNING: Use extreme Caution when using the Manual Forced Download Menu. Any file can be downloaded when selected and July cause the Main board to become inoperative if the incorrect file was selected. Highlight the Software update file which will appear at the bottom of the screen. (Scroll down if more than one file is on the jump drive). Press SELECT to begin the download process.
20
55LW56000
3) Information for Customer Support appears. Note: Model Number does not include suffix.
21
55LW56000
5) Press the (1) Key 5 times. The Host Diagnostics screen appears. 3) The Setup Menu appears.
22
55LW56000
Parental Control : Channel is not blocked DVI/HDMI Status Cant display this information now Wireless ready Status
Wireless Host Ver:0.00.0 Wireless B/B Ver:0.00.0 Micom Version : V2.21.2 RF Region Config : Not Configured Compile Date & Time : 20101130 & 08:45:52 Media Box Type : Not Configured RF Frequency (Value):Auto (N.A.) Compile User : hellyhorse.kang Uplink RF Power gain (Value):Auto (Min 0) FAT Status (Main) Downlink RF Power gain (Value):Auto:Auto (Min 0) Channel Frequency Center Frequency : 663.00 MHz Link Mode : Unicast Program Clock Reference (Locked or No) RX MAC Address : ff:ff:ff:ff:ff:ff PCR lock : Locked TX MAC Address : ff:ff:ff:ff:ff:ff Channel Type (8VSB, QAM 64, 256) Modulation mode : QAM 256 Wireless connection status : Disconnected Channel (Locked or Unlocked) Carrier lock status : Locked Average SNR [Db] : 0.0 (0) is good) 8VSB (Above 20 Channel Signal to Noise Ratio SNR : 37 dB QAM 64 (Above 24 is good) Signal level : 100%
Channel Signal Level (Above 80% good) QAM 256 (Above 30 is good)
Half Page
CH
Move Page
Exit
23
July 2011
LCD-DV 47LW5600
To access the Service Menu. 1) You must have either Service Remote. ) p/n 105-201M or p/n MKJ39170828 2) Press In-Start 3) A Password screen appears. 4) Enter the Password. )
Note: A Password is required to enter the Service Menu. Enter; 0000 ; Note: If 0000 does not work use 0413.
105-201M
MKJ39170828
24
55LW56000
IN START
1. Adjust Check Model Name: 55LW5600-UA 2. ADC Data Serial Number: 011PTCA8Y075 SW Version : 02.02.07.01 3. Power Off Status S/W Version: : 2.21.2 4. System 1 MICOM Version : 1.02.33 5. System 2 BOOT Version Video Processor : 20.ba 6. Model Number D/L FRC Version Chip Type : a2.0 7. Test Option IR LED Version : 0.00/0.00 8. External ADC EDID (RGB/HDMI) : BCM 35230 9. Spread Spectrum Chip Type : 0.00.0 10. Sync Level Wireless Host Ver. : 0.00.0 11. Wireless Ready Wireless B/B/ Ver. : 1.0 12. Stable Count Vi-Fi Version :0 13. ODC Test Vi-Fi Channel 14. Local Dimming Wi-Fi MAC : 00:00:00:00:00:00 15. SDP Server Selection MAC Address : E8:5B:5B:2E:C3:67 16. Network Error History Widevine : LGTV10L000010332 ESN Num. : LGE-LW4500XXXX00101F449C : 20.ba Formatter Version Electronic RF Receiver Version : VB091 Serial No. : RELEASE Debug Status UTT : 12 APP History Ver.:25329 PQL DB:LGD_AF_LGT10_XXXXXX
Units Total Time
Adjust Check Country Group 1. Country Group (Press OK to Save) Country Group Code 02 Country Group US Country US 2. Tool Option Tool Option 1 33179 Tool Option 2 4161 Tool Option 3 7295 Tool Option 4 21897 Tool Option 5 14925 Tool Option 6 665 3. Adjust White Balance: OK(0) 4. Adjust ADC: OTP 480i Component OK 1080p Component OK RGB OK 5. EDID(PCM): OK RGB OK (0x89) HDMI1 OK (0x5B,0x72) Priority Audio HDMI2 OK (0x5B,0x62) Processing Mode HDMI3 OK (0x5B,0x52) HDMI4 OK (0x5B,0x42)
25
July 2011
LCD-DV 55LW5600
Model Number D/L 0. Model Name 1. Serial Num. 55LW5600-UA 011PTCA8Y075 Press OK to Save
To Change the Model Number 1) Use the cursor right or left to select the digit to change. 2) Use the cursor up or down to change. 3) Press ENTER to Save 4) Cursor right until there is no cursor under the text. 5) Cursor down to highlight Serial Number and change per step 2 above. 6) Press ENTER to Save Note: If you need to return to the Model Number line, Cursor right until there is no cursor under the text and then press the Cursor Up button on the remote. Be sure to press Save after all changes are made on any line. After completion, press In-Start to update information on the left in the IN START Screen.
26
July 2011
LCD-DV 55LW5600
SYSTEM 1 1. Adjust Check 2. ADC Data 3. Power Off Status 4. System 1 5. System 2 6. Model Number D/L 7. Test Option 8. External ADC 9. Spread Spectrum 10. Sync Level 11. Wireless Ready 12. Stable Count 13. ODC Test 14. Local Dimming 15. SDP Server Selection 16. Network Error History 0. Baudrate 1. 2 Hours Off (On Timer) 2. 2 Hours Off (Screen Mute) 3. 15Min Force Off 4. Audio EQ 5. Dynamic EQ 6. A2 Threshold 7. HDMI Sound(Port1) 8. Lip Sync Adjust(DTV) 9. Dimming 10. Tuner Option 11. Atten RF Signal 12. UTT Reset 13. Channel Mute 14. Debug Status Changes 15. NVRAM Type to Doing 16. HDEV 17. Blue back 18. China Cable SO 19. Booster On (VHF) 20. Booster Off (VHF) 21. Booster On (UHF) 22. Booster Off (UHF) 23. Auto ADC
Scroll to (UTT Reset) Press (Select) Reset changes to Doing then back to Reset
9600 On Off On On On 11 HDMI Port1 0 On Default Off Reset On RELEASE EEPROM Off On On 0 0 0 0 On
After Reset (Doing) has completed, Reset returns. After Exit the UTT Timer is 0
27
July 2011
LCD-DV 55LW5600
If Item 5 on Adjust Check in the 1st page of the Service Menu shows EDID PCM this shows OK(PCM) If Item 5 on Adjust Check in the 1st page of the Service Menu shows AC3, this shows NG. If NG was shown, highlight Start and press Select on the remote. Writing appears, then OK/(PCM) shows here. Now Item 5 on Adjust Check in the 1st page of the Service Menu shows EDID PCM. If Reset is selected, Erasing will appear and then this shows NG.
If Item 5 on Adjust Check in the 1st page of the Service Menu shows EDID AC3 this shows OK(AC3) If Item 5 on Adjust Check in the 1st page of the Service Menu shows PCM, this shows NG. If NG was shown, highlight Start and press Select on the remote. Writing appears, then OK/(AC3) shows here. Now Item 5 on Adjust Check in the 1st page of the Service Menu shows EDID AC3. If Reset is selected, Erasing will appear and then this shows NG.
28
July 2011
LCD-DV 55LW5600
15-3/4" 400mm
Center
15-3/4" 400mm
15-7/16" 392.11m 7-7/8" 200m 2-5/8" (66.68mm) Remove 4 screws to remove stand for wall mount
Weight w/o Stand 48.5 lbs Weight with Stand 47.8 lbs
21-3/4" 552mm
13" 330.2mm
29
PASSIVE 3D SECTION
PASSIVE 3D This section of the manual will discuss the Passive 3D used in the 55LW56000 LCD Direct View Television. Upon completion of this section the Technician will have a better understanding of Passive 3D.
30
55LW56000
Advantages of Passive 3D
GLASSES AG-P110
Compatibility with all types of 3D Passive TV Maker Glasses can be made by p y polarized coating on normal g g glasses
31
55LW56000
PR Type of 3D Display
Pattern Retarder makes separation of polarization status. Each eye can see left and right images respectively when wearing polarized glasses glasses.
Right i Ri ht images input to odd lines i tt dd li Left images input to even lines
32
55LW56000
Polarized glasses
Left Eye
Right Eye
1. Patterned Retarder plate is attached on the LCD module 2. Patterned Retarder plate rotates odd line to CW 45 degree and even line CCW 45 degree 3. Odd number pixels see through the Left lens and even number pixels see through the Right lens of the Polarized glasses 4. The brain combines separated images into 3D image
33
55LW56000
Polarizer State
Pattern retarder makes 2 kinds of polarization states; LHC, RHC Polarizer glasses is possible to distinguish polarization state. state
Polarization State #4 (Linear) Polarizer Polarization St t P l i ti State #3 (Circular) Quarter Wave Plate Polarization State #2 (Circular) Pattern Retarder Polarization State #1 (Linear) Polarizer of LCD
Distinguish polarization state - LHC : Left Handed Circularly Polarization - RHC : Right Handed Circularly Polarization
Divides light output into 2 kinds of polarization states - LHC : Left Handed Circularly Polarization - RHC : Right Handed Circularly Polarization
34
55LW56000
LCD 3D Formatter
3D Formatter - All Formats of input are available and converted by 3D technology - Full HD input available p - 3D Enhancement Input Capabilities HDMI 1.3 / HDMI 1.4 Regular 2D 3D Formats (Frame Packed) 1) Side by Side 2D 3D Formatter or 2D 3D to 2D Output Capabilities
2) Top and Bottom Polarized Lens (Frame Retarder) over LCD panel and Polarized Glasses required R 4) Frame Sequential (Full Resolution available) L
3) Checkerboard
R L
35
55LW56000
LG 3D TV 3D broadcasting
3D for All types of broadcasting signals
1. 2. 3. 4. 5. Input of broadcasting signal Press 3D button for mode change Select type of input source, Press ENTER. In case 3D looks *abnormal, press 3D Settings in the Quick MENU. *Abnormality may be caused by reversed L/R *Ab lit b db d order of the input signal. If TV already in Left/Right change to Right/Left or vice versa.
HD Broadcasting
SD Broadcasting
Online Video
Input
Input
Input
(1)
HDMI Component RF
US USB Port
(2) (3)
Top & Bottom 2D to 3D Side by Side Checker Board Single frame Sequential
Note: Picture behind the menu is showing a side by side format. Note: HDMI 1.4 will automatically select 3D type for you.
36 36
55LW56000
3D Settings Menu
3D settings may help with 3D view pleasure.
1. 1 In case 3D looks *abnormal press 3D Settings abnormal, 3D Settings in the Quick MENU. 3D Picture Size: Cuts off the outer edges of the picture and stretch it to fit the full screen in 3D mode. 3D Depth: Adjusts the distance between the object and the background in the picture to enhance the 3D effect in 2D to 3D mode. 3D View Point: Brings the picture (including both the object and background images) to the front or back to enhance the 3D effect in 3D mode. 3D Picture Balance: Adjusts the color and brightness difference between the right and left sides of the picture in 3D mode. 3D Picture Correction: Changes the order of images in the right and left sides of the picture in 3D mode.
(1)
37 37
55LW56000
DISASSEMBLY SECTION
Disassembly: This section of the manual will discuss Disassembly Layout Disassembly, (Circuit Board Identification) of the 55LW56000 LCD Direct View Television. Upon completion of this section the Technician will have a better understanding of the disassembly procedures, the layout of the printed circuit boards and be able to identify each board.
38
55LW56000
8 Blocks
8 Blocks Each f the E h of th 16 bl k can b controlled blocks be t ll d independently (Local Dimming) or all of them as a group (Global Dimming) P-DIM This allows the panel to be darkened out in areas that are black or low brightness areas of the video. This allows for more deeper blacks and a thin design design. 39 July 201 LCD TV 1 55LW56000
Remove the 32 screws indicated. Pay attention to the size and type of screw as there are many different types. Putting in an improper screw when reassembling July Cause damage. g y g
The AC Cord unplugs under cover. Remove plastic cover.
40
55LW56000
To LEDs
LVDS Cables
T-CON
Panel Connection Points
Motion Remote
41
55LW56000
P203 P202
p/n: EBR72717002 (AUSYLHR) p/n: EBR73145701 (AUSYLJR) p/n: EBR72717004 (AUSYLUR) p/n: EBT61398007 (AUSYLUR) P3503
P102 n/c P5201 P101 n/c n/c
POWER SUPPLY
p/n: EAY62169901
Black Plug
White Plug
P701 n/c
P832 P201
P601 n/c
MAIN BOARD
CN2
CN4
T-CON
To TFT Panel
CN1
CN5
p/n: EAB62088401
p/n: EAB62088401
p/n: EBR72499601
42
July 2011
p/n EAY62169901
P701 n/c
P201
AC In
AC In
SK100
SK100 fits very snug into its connector. Press in on the two tabs to release lock
43
55LW56000
The Decorative Metal Plate is one Piece P5201 N/C P3503 P1702 Press in on the side release tabs to remove. Screw removed with Back P102 N/C
P101 N/C
2
Remove any tape holding down any cables. Remove the 5 (Maybe 6) screws indicated by the arrows. Press in on the two releasing tabs, pull the LVDS ribbons out. P1502
P1501 Decorative Metal Plate P601 N/C After removing the Main, there are tabs sticking through the Main board holding the Metal plate in place. Screw removed with Back
3
Remove the board.
4
Remove the board. Then Remove the wrap around decorative Metal piece piece. Note: It is one piece. p/n: EBR72717002 (AUSYLHR) p/n: EBR73145701 (AUSYLJR) p/n: EBR72717004 (AUSYLUR) / p/n: EBT61398007 (AUSYLUR)
P901 P1302
44
55LW56000
T-CON is under the Stand Bracket. Remove the Stand Bracket (4 Screws).
3
Disconnect CN1, CN2, CN4 and CN5. Return Screws if testing board. CN2 CN1
See next page for removing Connectors. Return Screws if testing b t ti board. d CN5 Flip up the unlocking tabs.
CN4
45
55LW56000
BROKEN TAB: If a tab is broken, Use a thin object And push in at the Location shown by The arrow on the left.
Removing LVDS
Press In
Pull Out
Press In
(CN2) LVDS
(CN1) LVDS
Removing Ribbons
CN4
CN5
Flip the locking tabs upward and p p g p pull out the ribbon cables.
46
55LW56000
300
Tab
Tab
Screw
Tab
Remove the one screw. Lift up on the three tabs at the top of Item 511 and pull th It ll the Item 511 slightly forward. li htl f d Lift Item 511 up and out.
510
511
47
55LW56000
300
After gaining access to the Front IR/Intelligent Sensor Board, lay the TV down on its face and remove the LCD Panel by releasing the tabs around the perimeter of the panel. Lift the Panel up and out. p p p The Front IR / Key Board is attached to the Front Frame Item 300 p/n: ABJ73289206. It must be separated to replace independently. Part number: EBR72671301.
510
511
48
55LW56000
TROUBLESHOOTING SECTION
Troubleshooting: g This section of the manual will discuss troubleshooting. Upon completion of this section the Technician will have a better understanding of how to diagnosis and resolve problems.
49
55LW56000
50
55LW56000
P202
P201 Connector "SMPS Board" To P502 "MAIN Board" Pin Label ERROR n/c PWM 12V n/c 12V DRV-ON 12V V-SYNC Gnd 3.5V Gnd 24V PWR-ON STBY n/c n/c 0V 0V n/c 0V 0V 0V n/c Gnd 3.56V Gnd 0V 0V Run n/c n/c 0.2V~3.3V 12.07V n/c 12.07V 3.24V 12.07V n/c Gnd 3.51V Gnd 25V 3.4V Diode Check 2.2V n/c OL 0.48V n/c 0.48V OL 0.48V n/c Gnd OL Gnd 1.1V 1.16V 24 23 22 21 20 19 18 17 16
BD101
+
63V
VC_1B VC_1C
VC_4D
VC_4C
VC_1A
VC_4B
VC_3C
VC_1D
VC_4A
- + - +
VC_2A
VC_3D
VC_2B
L601
C257 C256
D253
Q251
VC_2C VC_2D
VC_3B VC_3A
P701
n/c
Q602
D251
Q601
D252
P832
D255
D603 IC102
D256
T101
RL101
P201
D261 Stand-By 3.5V Source D202
F101
D201
(1)
F100
5A / 250V
F501
1A / 250V
Q102
F501
T501
IC502
P-DIM1 (Digital Dimming) Global Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and room light condition. 0.2V 0% to 3.3V 100% and the Intelligent Sensor. Output from the Video Processor IC900.
47uF/450V
47uF/450V
47uF/450V
47uF/450V
SK100 AC In
Different Size, W/Washer
Q101
IC501
63V Line: PWR-ON turns on the 63V supply but it will only be 56V. Note: A block of LEDs can be turned on with this voltage. It will increase to 63V when the DRV-ON line goes high.
MODEL LGP55-11SLPB INPUT 100-240V~50/60Hz 2.5A 3.5V = 1.8A 12V = 2.8A OUTPUT 24V = 1.2A 81.4V = 1.6A
SMPS TEST 1: To Force Power Supply On. Disconnect P502 on Main board. (A) Jump pins 9, 10, 11 or 12 (STBY_3.5V) to pin 1. Test Voltage Outputs 12V, 24V to Main and 56V to the Panel LEDs. Remove AC power. Leave the jumper in place. No Backlights at this time. SMPS TEST 2: (B) Jump pins 9, 10, 11 or 12 (3.5V) to pin 18 (DRV-ON). Apply AC power, the Backlights should turn on. Note, the LED B+ will now jump to 63V then back down to 63V. Note; If there is a problem with a load from the panel backlights, you can remove AC and Disconnect P202 or P203. When AC is reapplied, the Backlight LEDs should turn on for about 4 seconds and then shut off.
51
July 2011
LCD-DV 55LW5600
1
No AC Det in this model
Primary side fuses: F101 Stand-By 57V Run 396.5V (Hot Gnd) F501 Stand-By 154V Run 398.5V (Hot Gnd)
63V
Bridge
On Board Inverter
8 9 10
6 4 1
P203
6 8 8
12V/24V Regulators
63V
BACKLIGHTS To Panel Backlights 120Hz Manipulates Backlight LEDs Low = Bright LCD PANEL
P832
Local M0_SCLK Dimming MO_M0SI, +SCL2/SDA2 L_VS
16 Blocks
Local and Global Dimming P-DIM1 (PWM-DIM) Pulse Width Dimming Global Dimming
Manipulated by: Cust Menu for Backlight and Picture Content Manipulate P-DIM
Note 1: 12V SOURCE FOR: IC501 0.9V Core IC503 Power Det IC505 3.3V_Normal IC506 5V_USB IC507 5V_Normal IC5401 1.26V_FRC IC5402 3.3V_FRC Note 2: 24V SOURCE FOR: IC1702 Audio Amp IC502 Power Det Q1002 Wireless PWR
Video
PWR_ON
PWM-DIM
2
P502
3.5V_ST 2 5 Other Regs Power On/Off1/2 5
9~12
5
1
6
17 19 21
6
2~4
8
18
9
22
Globar Dimming
10
3 5 8
P3503
Inverter On
Q502
MAIN BOARD
See Note 2:
PWM-DIM
VCC 3.3V, HVDD 8V, VGL -5V, VGH 28V, VDD 16V
See Note 1:
Q507
Panel VCC 12V
T-CON PWB
12V LVDS 7 12V Tru-Motion LVDS Video
Q501 5 RL_ON
Q506-7
7 7
2 3
10
7 4 Video Processor IC101 FRC IC5201
52
July 2011
LCD-DV 55LW5600
Panel_Vcc (12V)
Q507
12V
S G
1.8V 12V 3.47V
R558 10K
R555 22K
+12V L511
Q506
0.68V
Q505
0V
R553
47K
6 3
PWR_ON 24V
L509
SMPS P201
1 2 3 4 5 6 7 8 3.4V 25V 25V 25V Gnd Gnd Gnd Gnd 3.51V 3.51V 3.51V 3.51V Gnd Gnd Gnd n/c 12.01V 3.24V 12.01V n/c 12.01V 0.2V~3.3V n/c n/c
MAIN P502
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 n/c n/c n/c
+3.3V_Normal
3.35V
7 8
IC505
2 6
+12V
R542 10K
6
20
R605
100
PWR_ON +24V
L504
Power_On/Off2_2
IC602 Micro
IR
C519 0.1uF
4
2.62V
16
Q502
0V
0V
Q501
0.64V
R508
4.7K
R502
10K
RL_ON
2
36 RL_ON
7 1
R643
22 Model_Opt_1 11
1
SBY3.5V
9 10 11 12 13 14 15
1
+3.5V_ST
L503
3.5V
40
5
IC8007 IC8008
8
12V
n/c DRV_ON
16 17 18 19 20 21 22 23 24
+3.3V_Normal
Q504
0V
INV_ON
8
10 R547 10K R228 22 AH17
Key 2 26
n/c
8 9
PWM-DIM_22 R526 0
R532
100
INV_CTL
9 PWM-DIM1
n/c ERR OUT
IC101 BCM
P832
1 0V 0.1V 0.12V
P3503
8
PWM-DIM1 (PWM Dimming) can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). Range 0.37V to 3.3V.
9
L_VS M0_SCLK M0_MOSI
SMPS
6 3
IC5201 BCM
53
June 2011
LCD-DV
55LW5600
P201
23 24 21 22 19 20 17 18 15 16 13 14
11 12 9 7 5 3 1 10 8 6 4 2
24V 24V
PWR_ON
54
55LW56000
P201
23 24 21 22 19 20
DRV_ON
17 18 15 16 13 14
11 12 9 7 5 10 8 6 4 2
24V
3 1
24V 24V
PWR_ON
If the DRV_On command is pulling up to at least 3V and the 63V is being g p g p g generated from C256 + leg, see the Inverter Section of the Power Supply for additional checks. Note: If either P202 or P203 is disconnected, the backlights will come on, The Error line will go high, then the backlights shut off in 4~6 seconds. REMOVE AC POWER:
55
55LW56000
LEDs
63V
Block Control Signals (Drive)
63V
Example Connector
Connector
63V P203 pin 1 and 13 B+ 8 blocks Block: VC-1A (EL62 Rivet) P203 pin 3
16 Total Blocks 8 Blocks per/board (8 on Left, 8 on Right) 10 LEDs per/block P202 or P203
EL62 ~ EL77 Test Point 1.59V Bright ~ 18V Dark
120Hz
Driver On SMPS
1 Block
6.14V drop per/LED max white
56
July 2011
LCD-DV
55LW5600
The Power Supply for the Backlights pp y g can be checked at the (+) side of C256 or C257 or the Cathode of D253. Note: When the PWR ON command PWR_ON Arrives, this voltage will read 56V. When the DRV_ON command arrives This voltage will rise to 63V.
C256
C257
P202 and P203 Backlight Driver Section of the SMPS Association with TPs
Tip: You can use the right side of R287 or R288 to check for the 63V. Tip: Remember to use a 220 to ground on any of the EL Test Points to force an LED Block to turn on.
63V
P203
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Label LED+ n/c VC-1A VC-1B VC-1C VC-1D n/c VC-2A VC-2B VC-2C VC-2D VC 2D n/c LED+ TP C256+ n/a EL62 EL63 EL64 EL65 n/a EL66 EL67 EL68 EL69 n/a C256+ EL69 EL70 EL68 EL71 EL67 EL66 EL65 EL64 EL63 EL62 EL77 EL76 EL75 EL74 EL72 EL73
P203
P202
1
Pin 1 2 3 4 5 6 7 8 9 10 11 12
P202
Label LED+ n/c VC-3A VC-3B VC-3C VC-3D VC-4A VC-4B VC-4C VC-4D n/c LED+ TP C256+ n/c EL70 EL71 EL72 EL73 EL74 EL75 EL76 EL77 n/c C256+
WARNING: Do not simply Ground any of the EL Test Points (EL62~EL77) to turn on an Ground LED Block. The LED Block will be destroyed.
58
55LW56000
P203
P202
63V
*The drive signal changes due to the brightness level of the backlights. L b kli ht Low indicates Bright. Hi h i di t Di i di t B i ht High indicates Dim.
Diode Mode values taken with all Connectors Removed
59
55LW56000
2mSec/div
P832 Pin 4 SIN 3.35V p/p P832 Pin 1 VSYNC 3.5V p/p
60
55LW56000
P832 Connector
61
55LW56000
P201 Connector
(1) PWR_ON Pi 1 t PWR ON Pin turns on the SMPS which send 12V and th hi h d d 24V to the Main. The 63V Power Supply turns on too, but only generates 56V at this time.
62
55LW56000
120Vac
AC Voltage Readings (From Hot Ground) Pins 1 and 2 for STBY and RUN.
F100
Diode Mode values taken with all Connectors Removed
F100 (Diode Check) Red or Black Lead on Fuse (Open) Other Lead on Hot Ground
SK100
63
55LW56000
F101 3.15A/250V From Hot Gnd STBY 57V Run 396 5V 396.5V
64
55LW56000
65
55LW56000
p/n: EBR72717002 AUSYLHR p/n: EBR73145701 AUSYLJR p/n: EBR72717004 AUSYLUR p p/n: EBT61398007 AUSYLUR VIDEO PROCESSOR IC101 Is under a Heat Sink. It runs Hot Hot. This is normal. USB 1 USB 2 See next page for component identification HDMI 4
IC1702 Audio
P102 n/c
P1502 To T-CON IC5201 FRC P1501 To T-CON IC602 Micro P901 To Ft. IR P1302 To Motion Remote RS232 n/c LAN RGB RGB Audio Optical P601 n/c IC101 BCM
HDMI 2
RF
66
55LW56000
P502
C
P3503
E B
Q504
B C E
Q502 Q501
3 1 3 1 2
E C B
RL_ON Drivers
INV_CTL
L1704
P5201 P102
0.9V_Core SW
Q503 IC501
0.9V_CORE
3.3V_ Normal
5V_Normal
IC507 IC506
5V_USB USB2 EDID
IC505 Q508
E B
0.9V_Core SW
P1702
IC5402
3.3V_FRC
L1707
P3502
DDR
NAND FLASH
Q5202
X101
45Mhz
IC102
URSA Reset
IC1203 IC103
NVRAM
IC401
BCM IC101
P3501
Q505
B E C B C E G D
RGB_DDC_SCL
G D D S B S G B
Q102 Q101
IC1204
Q710
USB1 EDID CEC
G D B S
Video Processor
RGB_DDC_SDA
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Label SCL SDA Gnd KEY 1 KEY 2 3.5V_ST Gnd LED_B/BUZZ IR Gnd +3.3V_Normal LED_R/BUZZ Gnd S/T_SCL S/T_SDA
STBY 3.55V 3.55V Gnd 3.33V 3.33V 3.55V Gnd 0V 1.5V Gnd 0.0V 0V Gnd 3.55V 3.55V
Run 3.48V 3.48V Gnd 3.31V 3.31V 3.48V Gnd 0V 1.41V Gnd 3.33V 0V Gnd 3.48V 3.48V
Diode Check 3.29V 3.29V Gnd 1.84V 1.84V 1.15V Gnd OL OL Gnd 0.55V 2.68V Gnd 1.91V 1.92
Q506
IC5401
1.26V_FRC
S
IC508
1.5V_DDR 2.5V_BCM35230
IC804 Q801
B E C
IC701
A1 A2
Q507 IC504
P601 N/C 10Mhz X601
Earphone Amp
D713 D711
C
A1 A2
P901
C
IC602
Q904
32.78K X602 C
B B E E C
MAIN BOARD
D C
IC601
EEPROM
Q906
E B E C B
RS232
Q901 Q902
SW1
SW1 Microprocessor Reset
p/n: EBR72717002 AUSYLHR p/n: EBR73145701 AUSYLJR Q1001 p/n: EBR72717004 AUSYLUR Wireless Power SW p/n: EBT61398007 AUSYLUR
Q1002
G S
D708
A1 A2
B E
IC803
P1302
IC802 IC801 PC EDID PC Data D810
C
A1 A2
TU2101 TUNER
18. IF p 17. IF n 16. IF AGC 15. Reset 14. 3.3V 13. 1.26V 12. GND 11. CVBS 10. NC 9. SIF 8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V 2. NC 1. NC
18
TU_CVSB
Q2105
B E C B E C
D710
C
2 1
A1 A2
IC2103
A1 A2
Q2104
TU_SIF
1
1.26V_TU
C
D707
67
July 2011
LCD-DV
55LW5600
Q502 Q501
E C B
E B
RL_ON Drivers
P5201 P102
0.9V_Core SW
P502
L1704 L1703
Q503 IC501
Audio Amp 0.9V_CORE
3.3V_ Normal
5V_Normal
IC507 IC506
5V_USB USB2 EDID
IC505 Q508
IC1702
L1708
1.5V_FRC
0.9V_Core SW
P1702
IC5402
3.3V_FRC
L1707
NAND FLASH
P3502
DDR
X101
45Mhz
IC102
IC1203 IC103
NVRAM
IC5201 FRC
X5201
BCM IC101
IC1204
Video Processor Earphone Amp
USB1 EDID
P3501
24MHz
1.5V_DDR 2.5V_BCM35230
IC701 IC804
1.26V_FRC MICRO
P601 N/C X601
IC5401
IC504
IC602
MAIN BOARD
D C B E
G S
HDMI Selector
10Mhz
P901
32.768KHz X602 C
B B E E C
Q1002
RS232
Q901 Q902
Q1001
SW1
Wireless Power SW
p/n: EBR72717002 AUSYLHR p/n: EBR73145701 AUSYLJR p/n: EBR72717004 AUSYLUR p/n: EBT61398007 AUSYLUR
18. IF p 17. IF n 16. IF AGC 15. Reset 14. 3.3V 13. 1.26V 12. GND 11. CVBS 10. NC 9. SIF 8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V 2. NC 1. NC
18
IC803
IC2103
3 2 1 2
P1302
IC801
PC Data
TU2101 TUNER
IC802
PC EDID
1.26V_TU
1
68
July 2011
LCD-DV
55LW5600
IC103 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC501 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] IC504 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC505 Pin [1] [2] [3] [4] [5] [6] [7] [8]
NVRAM for USB n/c 0V 3.34V 0V 3.22V 3.22V 0V (Gnd) 3.34V +0.9V_CORE DC to DC 3.17V 0.59V 0.44V 11.95V 0V 5.33V 4.6V 5.81V 0.95V 1.36V +2.5V BCM Regulator n/c 4.92V (En) 3.47V (In) 3.49V (Ctl) n/c 2.57V (Out) 0.6V 0V (Gnd) (+3.3V_NORMAL) Regulator 0V (Gnd) 11.96V (In) 0V (Gnd) 0.8V 0.79V 3.47V (PWR On/Off2_2) 3.35V (Out) 3.35V (Out)
IC506 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC507 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC508 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q901
Switched 5V for USB 2 0V (Gnd) 11.98V (In) 0V (Gnd) 0.79V 3.48V 3.48V (PWR On/Off2_1) 4.96V (Out) 4.96V (Out) (+5V_NORMAL) Regulator 0V (Gnd) 11.98V (In) 0V (Gnd) 0.79V 3.48V 3.48V (PWR On/Off2_1) 4.96V (Out) 4.96V (Out) (+1.5V_DDR) Regulator 3.46V n/c 3.46V (In) 3.49V (PWR On/Off1) 0V (Gnd) 3.31V 0.79V 1.5V (Out) IR Buffer 2nd
IC801 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] IC802 Pin [1] [2] [3] [4] [5] [6] [7] [8]
RGB Data Buffer 1.81V 1.81V 3.72V 1.8V 1.8V n/c (4.44V) 0V (Gnd) n/c (4.43V) n/c (1.79V) n/c (1.79V) 3.72V 1.81V 1.81V 5V (Vcc In) EDID Data PC 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.73V 4.73V 4.73V 4.73V (Vcc In)
IC803 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC1203 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC1204
RS232 Routing 3.5V 5.64V 0V 0V (-5.56V) (-5.59V) n/c (5.64V) n/c (0V) n/c (3.49V) n/c (0V) n/c (3.34V) 3.48V 0V (-5.59V) 0V (Gnd) 3.5V (Vcc In) EDID Data PC 0V (Gnd) 4.96V (Vcc In) 4.96V (Vcc In) 3.34V (USB Ctl2) 3.17V 4.96V (Out) 4.96V (Out) n/c (0V) EDID Data PC 0V (Gnd) 4.96V (Vcc In) 4.96V (Vcc In) 3.34V (USB Ctl1) 3.17V 4.96V (Out) 4.96V (Out) n/c (0V)
IC2103
(+1.26V_TU) Pin Regulator [1] 0V (Gnd) [2] 1.27V (Out) [3] 3.33V (In) (+1.26V_FRC) Regulator 0V (Gnd) 11.85V (Vcc In) 0V (Gnd) 0.8V (FB) 0.7V 3.29V (Enable) 1.29V (Out) 1.29V (Out) (+3.3V_FRC) Regulator Under Shield Under Shield Under Shield Under Shield 0.8V 3.45 (PWR On/Off2_2) 3.3V 3.3V
Q501
RL_ON (PWR_On) Pin 1st Driver B 0.64V C 0V E Gnd PWR_ON Pin Switch [1] 3.5V (In) [2] 0.67V [3] 2.62V (Out) 0.9V FET Switch 0.95V 0.95V 0.95V 1.36V 11.96V 11.96V 11.96V 11.96V 0.9V FET Switch 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.6V 0.95V 0.95V 0.95V 0.95V
IC5401 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC5402 Pin [1] [2] [3] [4] [5] [6] [7] [8]
Q502
Q503 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q508 Pin [1] [2] [3] [4] [5] [6] [7] [8]
Wireless Vcc Pin Driver B 0.02V C 24.5V E Gnd On when wireless dongle connected Wireless Vcc Pin Switch S 24.5V G 24.5V D 0V On when wireless dongle connected Q1002
Q1001
IR Buffer 1st
69
June 2011
47LW56500 LCD-DV
p/n: EBR72717002 AUSYLHR p/n: EBR73145701 AUSYLJR p/n: EBR72717004 AUSYLUR p/n: EBT61398007 AUSYLUR
IC502
2 3 1 3 1 2
Q504
B E C
IC503
INV_CTL
MAIN BOARD
C E B
Q1701
C B E
Amp Mute
Q5202
S G D
Q5201
URSA Reset
IC5202
RGB_DDC_SCL RGB_DDC_SDA
E B
Q102 Q101
B S G B
G D D S
SPI Flash
Q710
B S G D
CEC
A1 A2
Q801
E B C
C B E C
Q505 Q506
D713 D711
C
A2 A1
D708
C
A1 A2
Side HP Mute 18. IF p 17. IF n 16. IF AGC 15. Reset 14. 3.3V 13. 1.26V TU2101 12. GND 11. CVBS TUNER 10. NC 9. SIF 18 TU_CVSB
Q507
Digital Video
S G D
IC601
EEPROM
Q904
C C B E E B
Q906
IR Pass
D710
C
A2 A1
Q2105 Q2104
E B C E B C
D707
C
A1 A2
TU_SIF
1
8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V 2. NC 1. NC
D810
C
A2 A1
70
July 2011
LCD-DV
55LW5600
IC502
Power Det Gen Pin (For +12V) [1] 0V (Gnd) [2] 3.8V (In) [3] 3.73V (Out) Power Det Gen Pin (For +24V) [1] 0V (Gnd) [2] 3.7V (In) [3] 3.73V (Out) EEPROM Micro 0V (Gnd) 0V (Gnd) 3.49V 0V (Gnd) 3.49V 3.49V 0V (Gnd) 3.50V (Vcc In) SPI FLASH 0.43V 3.29V 3.29V 0V (Gnd) ?? ?? 3.29V 3.29V (3.3V_FRC in)
Q101 Pin [B] [G] [S] [D] Q102 Pin [B] [G] [S] [D] Q504 Pin B C E Q505
IC503
RGB_DDC_SDA FET Buffer 0V (Gnd) 3.3V 4.74V 3.34V RGB_DDC_SCL FET Buffer 0V (Gnd) 3.3V 4.74V 3.34V INV_CTL (Drv_On) Driver 0V (INV ON) En 3.28V (Out) Gnd PANEL_VCC
CEC Remote HDMI CEC 3.47V 3.51V 3.47V 3.49V Earphone Mute
Q2106
Tuner Video Pin (Analog) Buffer B 3.67V C 0V (Gnd) E 4.35V URSA Reset Pin Driver B 0.11V C 3.33V E 0V (Gnd) URSA Pin Reset G 3.33V S 3.33V D 0V (Out) 5V Pull-Up to Pin DDC_SCL/SDA_1 A1 4.96V C 5V A2 0V 5V Pull-Up to Pin DDC_SCL/SDA_3 A1 4.96V C 5V A2 0V 5V Pull-Up to Pin DDC_SCL/SDA_2 A1 4.96V C 5V A2 0V
D711
5V Pull-Up to Pin DDC_SCL/SDA_4 A1 4.96V C 5V A2 0V Bias for Q710 Pin HDMI CEC A1 0V C 3.45V A2 3.5V 5V Routing to Pin IC802 RGB EDID A1 4.73V C 5.01V A2 0.07V
D713
IC601 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC5202 Pin [1] [2] [3] [4] [5] [6] [7] [8]
D810
Q906
IR Wireless Pass Pin 1st Driver B 0.57V C 0V E Gnd AMP_MUTE Pin Pin 19 IC1702 B 0V C 3.36V E Gnd Tuner SIF Pin (Sound) Buffer B 0.23V C 0V (Gnd) E 0.93V
D708
Q506
PANEL_VCC
Control 2nd Driver Pin B 0.67V C 0V E Gnd
Q1701
D710
Q507 Pin S G D
Q2104
71
June 2011
47LW5600 LCD-DV
No Signal 3V p/p pp
24Mhz
Runs when set is on
1.18V
2.28V p/p pp
3.51V p/p
2.09V
Bottom leg g
3.3V / 3 3V p/p 2V
10Mhz
Runs all the time
MAIN Board
72
55LW56000
IC1702 VOLTAGES 3.3V_AU_AVDD pin 13 3.3V_DVDD pin 27 All made from 3.3V_Normal Right Channel: 24V pin 34, 35 (R-) 24V pin 40, 41 (R+) Left Channel: 24V pin 44, 45 (L-) 24V pin 2, 3 (L+) RR+ LL+ IC1702
(1)
Q1701 Back side of the board is (Mute) Active Low. 3.3V_ST Collector to AMP_MUTE_PDN Pin 19
73
55LW56000
74
55LW56000
P502 Main Board Connector to Power Supply Voltage and Diode Check
P502 "MAIN Board" Connector To P201 "SMPS Board"
P502
Label PWR-ON 24V Gnd 3.5V_ST 3 5V ST Gnd GND/VSYNC 12V DRV-ON 12V A-DIM 12V PDIM-1 n/c Err OUT
Run 3.4V 25V Gnd 3.51V 3 51V Gnd n/c 12.01V 3.24V 12.01V n/c 12.01V 12 01V 0.2V~3.3V n/c n/c
Diode Check 2.79V OL Gnd 1.15V 1 15V Gnd OL 2.09V 1.54V 2.09V OL 2.09V 2 09V 2.4V OL OL
(1)
PDIM Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). Range 0.2V to 3.3V.
P-DIM1 P DIM1 3.66V p/p 50IRE
75
55LW56000
P3501
There are no Stand-By Voltages for the Connector Diode Mode values taken with all Connectors Removed
76
55LW56000
P3502
Pins in Bold are Video Signals. There are no Stand-By Voltages for the Connector Stand By Connector. Diode Mode values taken with all Connectors Removed.
77
55LW56000
P901 Main Board to (Ft. IR/Intelligent Sensor) Voltage and Diode Check
P901 Connector "MAIN Board" To "IR Board" J1
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
(2) IR
( ) (3) (3)
Label
(1) (1)
STBY 3.55V 3.55V Gnd 3.31V 3.31V 3.55V Gnd 0V 1.5V Gnd 0V 0V Gnd 3.55V 3 55V 3.55V
Run 3.48V 3.48V Gnd 3.31V 3.31V 3.48V Gnd 0V 1.41V Gnd 3.33V 0V Gnd 3.48V 3 48V 3.48V
Diode Check 3.29V 3.29V Gnd 1.84V 1.84V 1.15V Gnd OL OL Gnd 0.55V 2.68V Gnd 1.91V 1 91V 1.92V
SCL
P901
SDA
IR
(1) Clock
& Data pulses only present when Intelligent Sensor is turned on. (3.6V p/p) pulses (2V p/p) (3) Clock & Data pulses only present when Set is turned on or Off. (3.9V p/p)
Diode Mode values taken with all Connectors Removed
78
55LW56000
P1302
79
55LW56000
JK1001 Main Wireless Media Box Dongle Jack (Voltage and Diode Check)
JK1001 "MAIN Board" To "Wireless Media Box Dongle"
Pin 1-6 7 8 9 10 11 12 13 14 15 16 17 18 19-20 Label *25V Detect Interrupt Gnd n/c Gnd I2C_SCL _ I2C_SDA Gnd Wireless_RX Wireless_TX Wi l TX Gnd IR Gnd STBY 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0.67V 0V Run 25V 0.3V 3.3V Gnd 3.3V Gnd 3.3V 3.3V Gnd 3.3V 3.3V 3 3V Gnd 3.3V Gnd Diode Check OL 2.39V OL Gnd OL Gnd 1.77V 1.77V Gnd OL OL Gnd OL Gnd 1 Diode Mode values taken with all Connectors Removed
Wireless Media Box Dongle must be plugged in for these voltages. JK1001 Jack J k
Voltages with Wireless Media Box Dongle plugged in. Use Media Box Dongle side to read voltages. Remove cover, (see Wireless Media Box training manual for details). *25V Switched from Q1002 Drain front side of the board. Q1002 turned on by Q1001 front side of the board board. Q1001 turned on by Microprocessor pin 38.
80
55LW56000
T-CON
81
55LW56000
CN2
CN1
CN5
CN4
82
55LW56000
LVDS
TO MAIN
12V
LVDS
PANEL TEST To run the T-CON Panel Test, remove the LVDS cables. Jump 12V to the 12V fuse. Jump VCC 3.3V to pin 44 on CN1. White, Red, Blue, Green and Black patterns show on screen.
CN3 n/c
V 12
Gnd Gnd Gnd Gnd
CN2
(3.35V)
Gnd
CN1
F1 3A/125V
(3.3V)
L3
L2
D6 US1
Panel Test TP 44
U5 U5
5) 3.3V 4) Gnd 6) 3.3V 3) Gnd 7) 3.15V 2) Gnd 8) 3.3V 1) Gnd
FL2
Gnd
VCC 3.3V
UC1
-5.3V
VDD 16.4V
Pin 18 (25.75V)1 (16.18V)
Q12
2 2
Q11
D1
2 3
D7
3 2 -2.43V 1
D3
U6
P-VDD 16.37V From VDD Pins 7-8
FL1
CN4
(3.3V)
VGL -5V
(3.3V)
C107 C108
VGH 27.74V
10
CN5
3.3V 16.4V
TO TFT MODULE
3.3V 16.4V
Other Voltages from U6 to the Panel with no silk screen labels: U6 pin 10: (16.12V) to CN4 pin 2, CN5 pin 59 U6 pin 11: (13.3V) to CN4 pin 3, CN5 pin 58 U6 pin 12: (12.2V) to CN4 pin 4, CN5 pin 57 U6 pin 13: (10.26V) to CN4 pin 5, CN5 pin 56 U6 pin 14: (5.9V) to CN4 pin 8, CN5 pin 53 U6 pin 15: (4.05V) to CN4 pin 9, CN5 pin 52 U6 pin 18: (3.01V) to CN4 pin 10, CN5 pin 51 U6 pin 19: (2.36V) to CN4 pin 11, CN5 pin 50
83
July 2011
LCD-DV
55LW5600
Jump 12V from the SMPS to the T CON Fuse F1 (P201 pin 17 or 19 or 21) T-CON 51 44
2 4
Jump 3.3V from the VCC TP to pin 44 of CN1
Disconnect both LVDS Cables Note: The connector has hash marks to indicate steps of 5. The marks are off one pin to the left. 5 is actually 6.
Apply AC to the Power Supply and Toggling patterns of White, Red, Blue, Green should appear on the screen
84
55LW56000
CN1 T-CON Connector CN1 to the Main PWB (Voltage and Diode Check)
CN1 "T-CON" to "MAIN Board" P3501 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Label n/c *3D_SYNC n/c SDA2_3.3V SCL2_3.3V SCL2 3 3V FRC_RESET LVDS_SEL n/c n/c PANEL_CTL Gnd TXA0N TXA0P TXA1N TXA1P TXA2N TXA2P Gnd TXACLKN TXACLKP Run n/c 0V n/c 3.3V 3.3V 3 3V 3.14V 0V n/c n/c 0V Gnd 1.23V 1.16V 1.25V 1.15V 1.27V 1.15V Gnd 1.19V 1.23V Diode Check n/c OL n/c OL OL OL OL n/c n/c OL Gnd 1.94V 1.94V 1.94V 1.94V 1.94V 1.94V Gnd 1.94V 1.94V Pin 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Label Gnd TXA3N TXA3P TXA4N TXA4P Gnd BIT_SEL TXB0N TXB0P TXB1N TXB1P TXB2N TXB2P Gnd TXBCLKN TXBCLKP Gnd TXB3N TXB3P TXB4N Run Gnd 1.29V 1.12V 1.33V 1.08V 1 08V Gnd 2.40V 1.23V 1.18V 1.24V 1.17V 1.29V 1.15V Gnd 1.19V 1.23V Gnd 1.27V 1 27V 1.31V 1.31V Diode Check Gnd 1.94V 1.94V 1.94V 1.94V 1 94V Gnd OL 1.94V 1.94V 1.94V 1.94V 1.94V 1.94V Gnd 1.94V 1.94V Gnd 1.94V 1 94V 1.94V 1.94V Pin 41 42 43 44 45 46 47 48 49 50 51 Label TXB4P Gnd Gnd Gnd Gnd Gnd n/c Panel_VCC Panel_VCC Panel_VCC Panel_VCC Run 1.08V Gnd Gnd Gnd Gnd Gnd n/c 11.98V 11.98V 11.98V 11.98V Diode Check 1.94V Gnd Gnd OL Gnd Gnd n/c OL OL OL OL
Bold labels are video signals. Pins 48~51 are 12V CN1
Pin 2 (3D_Sync) will go high when 3D is played. But is not used by the Main Board. y Diode Mode values taken with all Connectors Removed
Hash marks in steps of 5. First h h Fi t hash mark i off b 1 pin. k is ff by i Starts on pin 6.
85
55LW56000
CN2
86
55LW56000
1 Front IR and Soft Touch Key Board p/n EBR72671301 To Main Board
87
55LW56000
300
Tab
Tab
Screw
Tab
Remove the one screw. Lift up on the three tabs at the top of Item 511 and pull th It ll the Item 511 slightly forward. li htl f d Lift Item 511 up and out.
510
511
88
55LW56000
J1
1 Power LEDs
89
55LW56000
Label L b l SCL SDA Gnd KEY 1 KEY 2 3.5V_ST Gnd LED_B/BUZZ IR Gnd +3.3V_Normal LED_R/BUZZ Gnd S/T_SCL S/T SCL S/T_SDA
STBY 3.55V 3.55V Gnd 3.33V 3.33V 3.55V Gnd 0V 1.48V Gnd 0V 0V Gnd 3.55V 3.55V
Run R 3.49V 3.49V Gnd 3.33V 3.33V 3.49V Gnd 0V 1.47V Gnd 3.33V 0V Gnd 3.49V 3.49V
J1
& Data pulses only present when Intelligent Sensor is turned on. (3.6V p/p) (2) IR pulses (2V p/p) (3) Clock & Data pulses only present when Set is turned on or Off. (3.9V p/p)
Diode Mode values taken with all Connectors Removed
90
55LW56000
Pin 4 measured from Gnd 16.8M Ohms 10.7M Ohms 5 5.4M O s Ohms 1.19M Ohms
91
55LW56000
How to Re-register the Magic Motion Remote Control after Registration Failure. Reset the remote control by pressing and holding both the ENTER and MUTE buttons for 5 seconds. An LED will blink 3 times indicating the remote is ready for registering. Motion Remote Magic Remote AKB72914043
92
55LW56000
93
55LW56000
Back View
Front View
94
55LW56000
This section shows the 1 1X17 foldout thats available in the Paper and Adobe version of the Training Manual. g The Adobe version of this Training Manual allows the viewer to g zoom in and out making reading of the small text easier. This Power Point shows a graphical representation of the 1 X 17 1 foldout page so clarity is limited limited.
95
55LW56000
PWR-ON: Starts 12V, 24V and 63V LED Power. (56V at this time). No Backlights. DRV-ON: Starts Backlights. LED Power goes to 63V.
PWM Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor (room light condition). Output from the Video Processor. Range 0.2V to 3.3V.
(1)
To the Panel
P203 P202
Pin 1 2 3 4 5 6 7 8 9 10 11 12
Label LED+ n/c VC-3A VC-3B VC-3C VC-3D VC-4A VC-4B VC-4C VC-4D n/c LED+
TP C256+ n/c EL70 EL71 EL72 EL73 EL74 EL75 EL76 EL77 n/c C256+
Diode OL OL OL OL OL OL OL OL OL OL OL OL
SCLK Pin 6 P832 3.54V p/p MOSI Pin 4 P832 3.57V p/p Local Dimming Off MOSI Pin 4 P832 3.57V p/p Local Dimming On
BD101
+
- + - +
63V
VC_2A VC_2B
L601
C257 C256
D253
Q251
VC_2C VC_2D
VC_3B VC_3A
Pin Label ERROR 24 n/c 23 (1) 22 PWM 21 12V 20 n/c 19 12V 18 DRV-ON 17 12V 16 V_Sync 13-15 Gnd 9-12 3.5V 5-8 Gnd 2-4 24V 1 PWR-ON
STBY Run Diode Check n/c n/c 2.2V n/c n/c n/c 0V 0.2V~3.3V OL 0V 12.07V 0.48V n/c n/c OL 0V 12.07V 0.48V 0V 3.24V OL 0V 12.07V 0.48V 0V 0V OL Gnd Gnd Gnd 3.56V 3.51V OL Gnd Gnd Gnd 0V 25V 1.1V 0V 3.4V 1.16V
P502
C
P1302 "MAIN Board" To "Motion Remote" Pin 1 2 3 4 5 6 7 8 9 10 11 12 Label 3.5V_Normal Gnd M_Remote_RX M_Remote_TX Reset DC_MRemote DD_MRemote Gnd GPI0-O GPI0-1 GPI0-2 GPI0-3 STBY 0V Gnd 0V 0V 0V 0V 0V Gnd 0V 0V 0V 0V Run 3.41V Gnd 3.30V 3.31V 3.32V 3.31V 3.31V Gnd 0V 0V 0V 0V Diode Check 0.56V Gnd OL OL 2.41V 2.42V 2.40V Gnd OL OL OL OL
P502 "MAIN Board" To P201 "SMPS Board" Pin 1 2-4 5-8 9-12 Diode 2.79V OL Gnd 1.15V Gnd OL 2.09V 1.54V 2.09V OL 2.09V 2.4V OL OL
VC_1B VC_1C
VC_4D
VC_4C
VC_1A
VC_4B
VC_3C
VC_1D
VC_4A
P701
n/c
VC_3D
P3503
E B
Q504
INV_CTL
B C E
Q502 Q501
3 1 3 1 2
E C B
RL_ON Drivers
Q602
D251
Q601
D252
L1704
P5201 P102
0.9V_Core SW
P832
D255
Q503 IC501
0.9V_CORE
3.3V_ Normal
5V_Normal
IC507 IC506
5V_USB USB2 EDID
IC505 Q508
To Spk
12.43V Each Pin
D603 IC102
L1708
E B
0.9V_Core SW
13-15 16 17 18 19 20 21 22 23
D256
P1702
IC5402
3.3V_FRC
T101
RL101
P201
D261 Stand-By 3.5V Source D202
L1707
P3502
DDR
NAND FLASH
Q5202
X101
45Mhz
IC102
URSA Reset
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13
Label LED+ n/c VC-1A VC-1B VC-1C VC-1D n/c VC-2A VC-2B VC-2C VC-2D n/c LED+
TP C256+ n/a EL62 EL63 EL64 EL65 n/a EL66 EL67 EL68 EL69 n/a C256+
Run
63V
Diode OL OL OL OL OL OL OL OL OL OL OL OL OL
V-SYNC Pin 1 P832 3.5V p/p
F101
IC1203 IC103
NVRAM
D201
IC401
BCM IC101
n/c
F100
5A / 250V
F501
1A / 250V
Q102
F501
T501
IC502
P3501
Q505 Q506
B E C B C E G D
RGB_DDC_SCL
G D D S B S G B
Q102 Q101
IC1204
Q710
USB1 EDID CEC
G D B S
47uF/450V
47uF/450V
47uF/450V
47uF/450V
Video Processor
RGB_DDC_SDA
24
SK100 AC In
Different Size, W/Washer
IC5401
1.26V_FRC
S
IC508
1.5V_DDR 2.5V_BCM35230
IC804 Q801
B E C
For voltages, see SMPS Tables. P3503 "Main" to P832 "SMPS" Pin 1 2 3 4 5 6 7 Diode OL OL OL Gnd OL 1.73V 1.71V OL
IC701
A1 A2
Q101
IC501
Q507 IC504
P601 N/C 10Mhz X601
Earphone Amp
D713 D711
C
A1 A2
PANEL TEST To run the T-CON Panel Test, remove the LVDS cables. Jump 12V to the 12V fuse. Jump VCC 3.3V to pin 44 on CN1. White, Red, Blue, Green and Black patterns show on screen.
12V HVDD 8.21V L1 D5
Gnd
P901
C
IC602
Q904
32.78K X602 C
B B E E C
MAIN BOARD
D C
IC601
EEPROM
Q906
LVDS
12V
CN3 n/c
V 12
Gnd
E B E C B
LVDS
RS232
Q901 Q902
SW1
SW1 Microprocessor Reset
p/n: EBR72717002 AUSYLHR p/n: EBR73145701 AUSYLJR Q1001 p/n: EBR72717004 AUSYLUR Wireless Power SW p/n: EBT61398007 AUSYLUR
Q1002
G S
D708
A1 A2
B E
IC803
P201
23 24
23 24
12V 21 22 12V 19 20 12V 17 18 15 16 STBY 3.5V 9,10,11,12 13 14 11 12 9 10 7 8 A 5 6 1 2 24V 24V 3 4 24V PWR ON DRV-ON B
SMPS TEST 1: Force Power Supply On. Disconnect P502 on Main board. (A) Jump pins 9, 10, 11 or 12 (3.5V) to pin 1. Test Voltage Outputs 12V, 24V to Main and 63V to the LED Backlights. Remove AC power. Leave the jumper in place. No Backlights. 63V to Backlights reads 56V. SMPS TEST 2: Force the Backlights On. (B) Jump pins 9, 10, 11 or 12 (3.5V) to pin 18 (DRV-ON). Apply AC power, the Backlights should turn on. Note, the LED B+ will now be 65V. Note; If there is a problem with a load from the panel backlights, you can remove AC and Disconnect P202 or P203. When AC is reapplied, the Backlight LEDs should turn on for about 4 seconds and then shut off.
P1302
Warning: T-CON Board under shield. Be sure to reinsert screws before operating set with shield removed.
CN2
(3.35V)
Gnd
Gnd
Gnd
Gnd
CN1
F1 3A/ 125V Panel Test TP 44 U5
5) 3.3V 6) 3.3V 7) 3.15V 8) 3.3V
TU2101 TUNER
IC802
C
18. IF p 17. IF n 16. IF AGC 15. Reset 14. 3.3V 13. 1.26V 12. GND 11. CVBS 10. NC 9. SIF 8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V 2. NC 1. NC
18
TU_CVSB
Q2105
B E C B E C
D710
C 2 1
A1 A2
IC2103
A1 A2
Q2104
TU_SIF
1
1.26V_TU
C
L3
U5
4) Gnd 3) Gnd 2) Gnd 1) Gnd
L2
D6 US1
1 2 3
FL2
PC EDID
D707
Gnd
VCC 3.3V
UC1
-5.3V
A1 A2
VDD 16.4V
Pin 18 (16.18 V) (25.75V)
Q12
2
Q11
2
D1
D7
D2
1) 29.26.4V
3 2 -2.43V 1
D3
U6
P-VDD 16.37V From VDD Pins 7-8
C103 C104
FL1
CN4
(3.3V)
VGL -5V
(3.3V)
C107 C108
VGH 27.74V
10
P901 Connector "MAIN Board" To "IR Board" Pin Label STBY Run Diode Pin Label
Diode Gnd
For DC voltages for Main board components see Page 2 of the Interconnect diagram.
CN5
1 2 3 4
3.55V 3.48V 3.29V 3.55V 3.48V 3.29V Gnd Gnd Gnd 3.31V 3.31V 1.84V 3.31V 3.31V 1.84V
7 8 9 10 12
p/n: EBR72671301
Front IR/Key
Ft. IR/Intelligent Sensor And Soft Touch Key Board
LED SINGLE BLOCK TEST DIM OR DARK PICTURE: Confirm the 63V to the LED Backlights is present. Turn the Brightness, Contrast and Backlights all the way up. Confirm P-DIM is 3.3V. Using a 220 resistor, jump any of the blocks grounding lug (VC_1~4_A~D) while observing the picture and each block should turn on maximum.
3.3V 16.4V
TO TFT MODULE
3.3V 16.4V
5 6
11 +3.3V_Normal
3.33V 0.55V
Other Voltages from U6 to the Panel with no silk screen labels: U6 pin 10: (16.12V) to CN4 pin 2, CN5 pin 59 U6 pin 14: (5.9V) to CN4 pin 8, CN5 pin 53 U6 pin 11: (13.3V) to CN4 pin 3, CN5 pin 58 U6 pin 15: (4.05V) to CN4 pin 9, CN5 pin 52 U6 pin 12: (12.2V) to CN4 pin 4, CN5 pin 57 U6 pin 18: (3.01V) to CN4 pin 10, CN5 pin 51 U6 pin 13: (10.26V) to CN4 pin 5, CN5 pin 56 U6 pin 19: (2.36V) to CN4 pin 11, CN5 pin 50
Motion Remote
PANEL PART NUMBERS p/n: EAJ61750001 (All Models) p/n: EAJ61928201 (AUSYLJR/UR) p/n: EBR72499601
55LW5600 MAIN (FRONT SIDE) SIMICONDUCTORS IC103 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC501 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] IC504 Pin [1] [2] [3] [4] [5] [6] [7] [8] n/c 0V 3.34V 0V 3.22V 3.22V 0V (Gnd) 3.34V +0.9V_CORE DC to DC 3.17V 0.59V 0.44V 11.95V 0V 5.33V 4.6V 5.81V 0.95V 1.36V +2.5V BCM Regulator n/c 4.92V (En) 3.47V (In) 3.49V (Ctl) n/c 2.57V (Out) 0.6V 0V (Gnd) IC506 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC507 Pin [1] [2] [3] [4] [5] [6] [7] [8] NVRAM for USB IC505 Pin [1] [2] [3] [4] [5] [6] [7] [8] (+3.3V_NORMAL) Regulator 0V (Gnd) 11.96V (In) 0V (Gnd) 0.8V 0.79V 3.47V (PWR On/Off2_2) 3.35V (Out) 3.35V (Out) Switched 5V for USB 2 0V (Gnd) 11.98V (In) 0V (Gnd) 0.79V 3.48V 3.48V (PWR On/Off2_1) 4.96V (Out) 4.96V (Out) (+5V_NORMAL) Regulator 0V (Gnd) 11.98V (In) 0V (Gnd) 0.79V 3.48V 3.48V (PWR On/Off2_1) 4.96V (Out) 4.96V (Out) IC508 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC801 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] (+1.5V_DDR) Regulator 3.46V n/c 3.46V (In) 3.49V (PWR On/Off1) 0V (Gnd) 3.31V 0.79V 1.5V (Out) RGB Data Buffer 1.81V 1.81V 3.72V 1.8V 1.8V n/c (4.44V) 0V (Gnd) n/c (4.43V) n/c (1.79V) n/c (1.79V) 3.72V 1.81V 1.81V 5V (Vcc In) IC803 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC802 Pin [1] [2] [3] [4] [5] [6] [7] [8] EDID Data PC 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.73V 4.73V 4.73V 4.73V (Vcc In) RS232 Routing 3.5V 5.64V 0V 0V (-5.56V) (-5.59V) n/c (5.64V) n/c (0V) n/c (3.49V) n/c (0V) n/c (3.34V) 3.48V 0V (-5.59V) 0V (Gnd) 3.5V (Vcc In) IC1203 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC1204 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC2103 Pin [1] [2] [3] EDID Data PC 0V (Gnd) 4.96V (Vcc In) 4.96V (Vcc In) 3.34V (USB Ctl2) 3.17V 4.96V (Out) 4.96V (Out) n/c (0V) EDID Data PC 0V (Gnd) 4.96V (Vcc In) 4.96V (Vcc In) 3.34V (USB Ctl1) 3.17V 4.96V (Out) 4.96V (Out) n/c (0V) (+1.26V_TU) Regulator 0V (Gnd) 1.27V (Out) 3.33V (In) IC5401 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC5402 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q501 Pin B C E Q502 (+1.26V_FRC) Regulator 0V (Gnd) 11.85V (Vcc In) 0V (Gnd) 0.8V (FB) 0.7V 3.29V (Enable) 1.29V (Out) 1.29V (Out) (+3.3V_FRC) Regulator Under Shield Under Shield Under Shield Under Shield 0.8V 3.45 (PWR On/Off2_2) 3.3V 3.3V RL_ON (PWR_On) 1st Driver 0.64V 0V Gnd Q503 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q508 Pin [1] [2] [3] [4] [5] [6] [7] [8] 0.9V FET Switch 0.95V 0.95V 0.95V 1.36V 11.96V 11.96V 11.96V 11.96V 0.9V FET Switch 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.6V 0.95V 0.95V 0.95V 0.95V Wireless Vcc Pin Driver B 0.02V C 24.5V E Gnd On when wireless dongle connected Wireless Vcc Pin Switch S 24.5V G 24 5V 24.5V D 0V On when wireless dongle connected Q1002 Q1001
Q901
IR Buffer Pin 2nd B 0.02V C 3.48V E Gnd IR Buffer Pin 1st B 0.57V C 0.02V E Gnd
Q902
PWR_ON Pin Switch [1] 3.5V (In) [2] 0.67V [3] 2.62V (Out)
55LW5600 MAIN (BACK SIDE) SIMICONDUCTORS IC502 Power Det Gen Pin (For +12V) [1] 0V (Gnd) [2] 3.8V (In) [3] 3.73V (Out) Power Det Gen Pin (For +24V) [1] 0V (Gnd) [2] 3.7V (In) [3] 3.73V (Out) Q506 IC601 Pin [1] [2] [3] [4] [5] [6] [7] [8] EEPROM Micro 0V (Gnd) 0V (Gnd) 3.49V 0V (Gnd) 3.49V 3.49V 0V (Gnd) 3.50V (Vcc In) IC5202 Pin [1] [2] [3] [4] [5] [6] [7] [8] SPI FLASH 0.43V 3.29V 3.29V 0V (Gnd) ?? ?? 3.29V 3.29V (3.3V_FRC in) Q101 Pin [B] [G] [S] [D] Q102 Pin [B] [G] [S] [D] Q504 RGB_DDC_SDA FET Buffer 0V (Gnd) 3.3V 4.74V 3.34V RGB_DDC_SCL FET Buffer 0V (Gnd) 3.3V 4.74V 3.34V Q710 Pin [B] [G] [S] [D] Q801 Pin B 0V C 3.35V E Gnd Q904 INV_CTL (Drv_On) INV CTL (Drv On) Pin Driver B 0V (INV ON) En C 3.28V (Out) E Gnd Q906 Q505 PANEL_VCC Pin Control 1st Driver B 0V C 0.68V E Gnd Pin B C E Pin B C E 3.47V 3.51V 3.47V 3.49V Q2106 Earphone Mute CEC Remote HDMI CEC Q2104 Tuner SIF Pin (Sound) Buffer B 0.23V C 0V (Gnd) E 0.93V Tuner Video Pin (Analog) Buffer B 3.67V C 0V (Gnd) E 4.35V URSA Reset Pin Driver B 0.11V C 3.33V E 0V (Gnd) URSA Pin Reset G 3.33V S 3.33V D 0V (Out) D707 Pin A1 C A2 D708 Pin A1 C A2 D710 Pin A1 C A2 D711 Pin A1 C A2 5V Pull-Up to DDC_SCL/SDA_1 4.96V 5V 0V 5V Pull-Up to DDC_SCL/SDA_3 4.96V 5V 0V 5V Pull-Up to DDC_SCL/SDA_2 4.96V 5V 0V 5V Pull-Up to DDC_SCL/SDA_4 4.96V 5V 0V D713 Bias for Q710 Pin HDMI CEC A1 0V C 3.45V A2 3.5V 5V Routing to IC802 RGB EDID 4.73V 5.01V 0.07V
IC503
D810 Pin A1 C A2
PANEL_VCC Pin Control 2nd Driver B 0.67V C 0V E Gnd PANEL_VCC Pin Switch S 11.97V (In) G 1.8V (Enable) D 11.94V (Out)
Q5201 IR Wireless Pass 2nd Driver 0.02V 3.48V Gnd Q5202 IR Wireless Pass 1st Driver 0.57V 0V Gnd
Q507
3D
This Thi concludes th 55LW56000 l d the training session.