Professional Documents
Culture Documents
TM
ACCUWRAP
Center Shaft Permits Use Of Different Size Shafts Right Wing
TM
Wheel Adjustment Nut Used To Get Lap Adjustment For Different Size Tapes And Pipe
Left Wing
Please Note: Sawyer Accuwrap machines are sized by the width of the wrapping tape they use; 2-6 (50.8 - 152.4mm), 6-12 (152.4mm - 304.8mm) and 12-18 (304.8mm - 457.2mm). Any Accuwrap machine will fit any size pipe.
Wheels - Set wheels as far apart as possible without the machine or roll of tape rubbing on the pipe. Plain Tape - (see diagram) 1. Remove TENSION KNOB and LOCKING WING NUT, loosen HANDLE and load desired tape size by latching onto spool. Tape coating should unravel from top of roll placing TENSION KNOB on operators left. 2. Adjust TENSION KNOB sufficient to elongate the coating. Ideal tension is 5-10 lbs/in-width (2.3-4.5kg/mm-width). 3. To wrap, grasp HANDLE and rotate down the pipe by grabbing it by the opposite HANDLE as it comes down. 4. Lap size is increased by loosening ADJUSTMENT NUT and moving bolt to higher level in slot placing WINGS in more parallel position. Cigarette wraps should have wings in completely parallel position. 5. Lap size is decreased by moving bolt to lower position in slot increasing angle between the wings. 6. For double wrapping, either wrap same area twice or adjust lap for half as much travel.
PLAIN TAPE
Tape
Wrapping Direction
Pipe
To Apply the Tape Hold the end of the tape away from the pipe surface, set the machine on the pipe, make sure all four wheels are touching the pipe, carefully lay the tape on the pipe surface smooth and straight and press it down. Then pull the machine in the direction as shown in the appropriate diagram, by the handle, around the pipe.
ACCUWRAP
PARTS LIST
7 5 6 8 10
TM
16 4 5 6
13
15
3 11 24
12 14
Parts List
No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Amount 1 2 1 1 6 4 4 4 1 1 Dwg./Part No. 7AM - 1 7AM - 2 7AM - 3 7AM - 4 7AM - 5 7AM - 6 7AM - 7 7AM - 8 7AM - 9 7AM - 10 Description/Name Knob, Tension Washer Spring Wing - Left Wing Nut Spacer - only on 6 mach. Wheel Assy. Bolt, Axle Bolt, Clamp Bar Assy., Adjusting No. 11. 12. 13-6. 13-12. 13-18. 14-6. 14-12. 14-18. 15. 16. Amount 1 1 1 1 1 2 2 2 1 1 Dwg./Part No. 7AM - 11 7AM - 12 7AM - 13-6 7AM - 13-12 7AM - 13-18 7AM - 14-6 7AM - 14-12 7AM - 14-18 7AM - 15 7AM - 16 Description/Name Nut Washer Shaft, Center - 6 Shaft, Center - 12 Shaft, Center - 18 Handle - 6 Handle - 12 Handle - 18 Pin, Hitch Wing - Right
Since 1948, Sawyer Mfg. Company has specialized in the design and manufacture of pipeline and welding equipment that has become the "standard of the industry". Sawyer Mfg. offers a compete line of pipe beveling and cutting machines and accessories that are adaptable to plasma cutting. Sawyer equipment is used worldwide in the construction of pipeline, waste water and sewer lines; gathering and distribution systems and other welding and pipeline applications.