Professional Documents
Culture Documents
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
N UTS S ELF-CLINCHING
Revised 108
For load-bearing threads in thin sheets aluminum, steel, and other ductile materials. Proved Performance For over 60 years, PEM brand self-clinching fasteners have satisfied production and fastening requirements wherever loadbearing threads are required in thin metal sections too thin to tap. Quick, convenient assembly using standard tools Installation of PEM brand self-clinching nuts is simple, quick, and convenient. Just insert them in punched or drilled holes, then apply a squeezing force to embed the clinching ring completely in the sheet metal. High pushout & torque-out resistance The clinching ring locks the displaced metal behind the tapered shank, ensuring high pushout resistance. High torque-out resistance is ensured when the knurled platform is embedded in the sheet metal.
Look for the PEM trademarks
Distortion-free installation Proper installation forces will not distort or damage the threads in PEM nuts because the recommended shank length is always less than the minimum sheet thickness. Reverse side remains flush All clinching takes place on the fastener side of the sheet. The reverse side remains flush and smooth.
Self-clinching Locknuts These locknuts (Type SL) are designed with a unique and economical TRI-DENT locking feature, which meets demanding locking performance requirements.
Thin Sheet Self-clinching Nuts These nuts (Type SMPS) feature a lower profile and can be mounted closer to the edge of a sheet than standard self-clinching nuts. Self-clinching nuts for stainless steel PEM 300 self-clinching nuts (Type SP) are especially designed for permanent installation into stainless steel sheets as thin as .030/ 0.8 mm.
Machined from a specialty stainless steel, these fasteners are then heat-treated to a hardness higher than most 300 Series stainless steels. This feature enables PEM 300 fasteners to be installed into stainless steel sheets, employing the same self-clinching principle which has proved successful over the years in thousands of applications.
sa l
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
S
440
ZI
Thread Code
Shank Code
Finish
Many PEM self-clinching nuts meet NASM45938/1specifications. Consult our Marketing department for a complete Military Specifications and National Aerospace Standards guide (Bulletin NASM) or check our website.
CL-2
PennEngineering www.pemnet.com
2000 PennEngineering
STEEL AND STAINLESS STEEL NUTS (Unified) TYPES S, SS, CLS, and CLSS
E C
A T
(Clinching profile may vary)
All dimensions are in inches. Type Thread Size .086-56 (#2-56) .099-48 (#3-48) .112-40 (#4-40) Fastener Material Carbon Steel Stainless Steel S CLS Thread Code 256 Shank Code 0 1 2 0 1 2 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 A (Shank) Max. .030 .038 .054 .030 .038 .054 .030 .038 .054 .087 .030 .038 .054 .087 .030 .038 .054 .087 .030 .038 .054 .087 .030 .038 .054 .087 .038 .054 .087 .045 .054 .087 .120 .054 .087 .120 .054 .087 .120 .054 .087 .120 .087 .120 .235 .087 .120 .235 .120 .235 .120 .235 Hole Size In Sheet +.003 -.000 .166 Min. Dist. Hole C/L To Edge (1) .19
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
CLS 348NS cls 440 cls 632 CLS 832 CLSS 024 CLSS 032 .030 .040 .056 .030 .040 .056 .030 .040 .056 .091 .030 .040 .056 .091 .030 .040 .056 .091 .030 .040 .056 .091 .030 .040 .056 .091 .040 .056 .091 .047 .056 .091 .125 .056 .091 .125 .056 .091 .125 .056 .091 .125 .091 .125 .250 .091 .125 .250 .125 .250 .125 .250 .165 .25 .166 .165 .25 .166 .165 .25 .1875 .187 .28 .213 .212 .31 .250 .249 .34 .250 .249 .34 CLS 1224 CLS 0420 CLS 0428 CLS 0518 CLS 0524NS CLS 0616 CLS CLSNS CLSNS 0624NS 0813 0820 1NS 2 3 0 1 2 3 1 2 3 NS 1 2 3 1 2 3 1 2 3 1 2 3 1 2 1 2 .277 .276 .37 .344 .343 .44 .344 .343 .44 .413 .412 .50 .413 .412 .50 .500 .499 .56 .500 .499 .56 .656 .655 .81
C Max.
E .010
T .010 .07
.07
.19
.07
.19
.138-32 (#6-32)
.07
.22
.164-32 (#8-32)
.09
.27
.190-24 (#10-24)
SS
.09
.28
UNIFIED
.190-32 (#10-32) .216-24 (#12-24) .250-20 (1/4-20) .250-28 (1/4-28) .313-18 (5/16-18) .313-24 (5/16-24) .375-16 (3/8-16) .375-24 (3/8-24) .500-13 (1/2-13) .500-20 (1/2-20)
SS
.09
.28
.13
.31
.17
.34
sa l
.17
.34
.23
.38
.23
.38
.27
.44
S S S
.27
.44
.36
.63
(1) To minimize sheet distortion and maximize product performance, use a centerline-to-edge value greater or equal to the value specified. (NS) Not Stocked, available on special order. PennEngineering www.pemnet.com
CL-3
STEEL AND STAINLESS STEEL NUTS (Metric) TYPES S, SS, CLS, and CLSS
A
(Clinching profile may vary)
All dimensions are in millimeters. Thread Size x Pitch m2 x 0.4 Type Fastener Material Carbon Steel Stainless Steel s clsNS Thread Code m2 Shank Code 0 1 2 A (Shank) Max. 0.77 0.97 1.38 Hole Size In Sheet +0.08 4.22 Min. Dist. Hole C/L To Edge (1) 4.8
C Max. 4.2
E 0.25 6.3
T 0.25 1.5
m2.5 x 0.45
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
cls m2.5 0 1 2 0.77 0.97 1.38 0.8-1 1 1.4 4.22 4.2 6.3 1.5 cls m3 0 1 2 0.77 0.97 1.38 0.8-1 1 1.4 4.22 4.2 6.3 1.5 cls m3.5 0 1 2 0.77 0.97 1.38 0.8-1 1 1.4 4.75 4.73 7.1 1.5 cls m4 0 1 2 0.77 0.97 1.38 0.8-1 1 1.4 5.41 5.38 7.9 2 clss m5 0 1 2 0.77 0.97 1.38 0.8-1 1 1.4 0.92 1.2 1.4 2.3 6.35 6.33 8.7 2 cls m6 00 0 1 2 1 2 1 2 0.89 1.15 1.38 2.21 8.75 8.72 11.05 4.08 clsNS cls m8 m10NS 1.38 2.21 2.21 3.05 1.4 2.3 2.31 3.18 10.5 14 10.47 12.65 5.47 13.97 17.35 7.48
4.8
m3 x 0.5 METRIC
4.8
m3.5 x 0.6
5.6
m4 x 0.7
6.9
m5 x 0.8
ss
7.1
m6 x 1
8.6
s s
9.7 13.5
sa l
Shank Code 1 2 1 2
A (Shank) Max. .038 .054 .038 .054 .038 .054 .038 .054 .038 .054 .038 .054 .054 .087 .120
Min. Sheet Thickness .040 .056 .040 .056 .040 .056 .040 .056 .040 .056 .040 .056 .056 .091 .125
Hole Size In Sheet +.003 -.000 .166 .1875 .213 .234 .296 .296 .344
Min. Dist. Hole C/L To Edge (1) .19 .22 .27 .28 .31 .31 .34
1 2 1 2 1 2 1 2 1 2 3
(1) To minimize sheet distortion and maximize product performance, use a centerline-to-edge value greater or equal to the value specified. (NS) Not Stocked, available on special order.
CL-4
PennEngineering www.pemnet.com
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
C E C A T1 A T2
Type SelfLocking* HNL Thread Code 0420 A (Shank) Max. .058 Min. Sheet Thickness .058 Hole Size In Sheet +.005 -.000 .344 C Max. .343 E .010 .500 T1 Non-locking .005 .189 HNL 0518 .058 .058 .413 .412 .575 .240 HNL 0616 .058 .058 .500 .499 .650 .300 Type SelfLocking* HNL HNL HNL Thread Code M6 M8 M10 A (Shank) Max. 1.48 1.48 1.48 Min. Sheet Thickness 1.48 1.48 1.48 Hole Size In Sheet +0.13 8.75 10.5 12.7 C Max. 8.72 10.47 12.67 E 0.25 12.7 14.6 16.5 T1 Non-locking 0.13 5 6.3 7.9
UNIFIED
NonLocking NA NA H HN
T2 Self-locking .010
All dimensions are in millimeters. Thread Size x Pitch M6 x 1 M8 x 1.25 M10 x 1.5
sa l
METRIC
NonLocking NA NA H HN
T2 Self-locking 0.25
(1) To minimize sheet distortion and maximize product performance, use a centerline-to-edge value greater or equal to the value specified. (NS) Not Stocked, available on special order. (NA) Not Available - Use Type S instead. * During installation, the projections on the heads of Type HNL self-locking nuts may be flattened. This is not detrimental in any way and will not affect self-locking or self-clinching performance.
PennEngineering www.pemnet.com
CL-5
A T
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
Thread Code 440 Shank Code 0 1 2 0 1 2 0 1 2 0 1 2 A (Shank) Max. .030 .038 .054 .030 .038 .054 .030 .038 .054 .030 .038 .054 Sheet Thickness Hole Size In Sheet +.003-.000 (2) .166 C Max. .165 E .010 .25 T .010 .07 632 832 032 .030 - .039 .040 - .055 .056 Min. .030 - .039 .040 - .055 .056 Min. .030 - .039 .040 - .055 .056 Min. .030 - .039 .040 - .055 .056 Min. .056 Min. .1875 .187 .28 .07 .213 .212 .31 .09 .250 .249 .34 .09 0420 1 .054 .344 .343 .44 .17 Thread Code m3 Shank Code 0 1 2 0 1 2 0 1 2 A (Shank) Max. 0.77 0.97 1.38 0.77 0.97 1.38 0.77 0.97 1.38 Sheet Thickness Hole Size In Sheet +0.08 (2) 4.22 C Max. 4.2 E 0.25 6.3 T 0.25 1.5 m4 m5 0.8 - 1 1.01 - 1.39 1.4 Min. 0.8 - 1 1.01 - 1.39 1.4 Min. 0.8 - 1 1.01 - 1.39 1.4 Min. 1.4 Min. 5.41 5.39 7.9 2 6.35 6.33 8.7 2 m6 1 1.38 8.75 8.73 11.1 4.1
Type
SP
SP
.22
SP
.27
SP SP
.28 .34
Type
m3 x 0.5
SP
m4 x 0.7
SP
6.9
m6 x 1
sa l
m5 x 0.8
SP
7.1 8.6
SP
(1) To minimize sheet distortion and maximize product performance, use a centerline-to-edge value greater or equal to the value specified. (2) Hole punch diameter must be maintained at +.001 / .025mm over mounting hole diameter. Hole punch should be kept sharp to minimize local work hardening around hole. Fasteners should be installed in the punch side of the hole.
CL-6
PennEngineering www.pemnet.com
A
PEM TRI-DENT Locking Feature
Thread Size .112-40 (#4-40) UNIFIED .138-32 (#6-32) .164-32 (#8-32) .190-32 (#10-32) .250-20 (1/4-20)
Type SL SL SL SL SL
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
Thread Code 440 Shank Code 1 A (Shank) Max. .038 Min. Sheet Thickness .040 C Max. E .010 .250 T .010 .070 2 1 .054 .038 .056 .040 .166 .165 632 2 1 .054 .038 .056 .040 .1875 .213 .187 .280 .070 832 2 .054 .056 .212 .310 .090 032 1 .038 .040 2 .054 .056 .250 .249 .340 .090 0420 1 .054 .056 2 .087 .091 .344 .343 .440 .170 Thread Code M3 Shank Code 1 2 A (Shank) Max. 0.98 1.38 Min. Sheet Thickness 1 1.4 1 Hole Size In Sheet +0.08 4.25 C Max. 4.22 E 0.25 6.3 T 0.25 1.5 M3.5 M4 1 0.98 2 1.38 1.4 1 4.75 5.4 4.73 7.1 1.5 2 1 0.98 2 1 1.38 0.98 1.4 1 5.38 7.9 M5 2 1 2 1.38 1.38 2.21 1.4 1.4 2.3 6.4 6.38 8.7 2 M6 8.75 8.72 11.05 4.08
Min. Dist. Hole C/L To Edge .190 .220 .270 .280 .340
All dimensions are in millimeters. Thread Size x Pitch M3 x 0.5 METRIC M3.5 x 0.6 M4 x 0.7 M5 x 0.8 M6 x 1
Type SL SL SL SL
Min. Dist. Hole C/L To Edge 4.8 5.6 6.9 7.1 8.6
sa l
SL
PennEngineering www.pemnet.com
CL-7
A T
Depending on thread size, Type SMPS nuts can be installed up to 40% closer to the edge of a sheet than standard self-clinching nuts.
Type
SMPS
SMPS
SMPS
All dimensions are in millimeters. Thread Size x Pitch METRIC M2.5 x 0.45
Type
SMPS
M3 x 0.5
SMPS
M3.5 x 0.6
SMPS
CL-8
PennEngineering www.pemnet.com
sa l
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
Thread Code 256 A (Shank) Max. .024 Min. Sheet Thickness .025 Hole Size In Sheet +.003 -.000 .136 C Max. .135 E .010 .220 T .010 .065 Min. Dist. Hole C/L To Edge .145 440 .024 .025 .166 .165 .220 .065 .170 632 .024 .025 .187 .186 .252 .065 .200 Thread Code M2.5 A (Shank) Max. 0.61 Min. Sheet Thickness 0.64 Hole Size In Sheet +0.08 3.8 C Max. 3.79 E 0.25 5.6 T 0.25 1.4 Min. Dist. Hole C/L To Edge 3.7 M3 0.61 0.64 4.24 4.22 5.6 1.4 4.3 M3.5 0.61 0.64 4.75 4.73 6.4 1.4 5.1
Thread Mask
PEM Blu-Coat thread mask is available for applications where hardware is installed prior to painting. During assembly, the threads of the mating hardware will remove paint, electro deposited automotive under coatings, and weld spatter upon application of torque. PEM nuts can be specially ordered with thread mask applied.
PERFORMANCE DATA(1)
TYPE S, CLS, CLSS
Type Thread Code 256 348 440 Shank Code 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 1 2 3 1 2 3 0 1 2 3 0 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 1 2 Test Sheet Material 5052-H34 Aluminum Cold-rolled Steel 5052-H34 Aluminum Cold-rolled Steel 5052-H34 Aluminum Installation (lbs.) 1500-2000 Pushout (lbs.) 63 90 170 170 105 125 230 230 63 95 190 190 110 130 275 275 68 105 220 220 110 145 285 285 68 110 190 225 120 180 250 320 120 285 285 200 350 350 220 360 Torque-out (in. lbs.) 8 10 13 13 13 15 18 18 16 17 22 22 16 20 28 28 21 23 35 35 26 35 45 45 26 32 50 50 32 40 60 60 63 70 70 74 80 80 70 90 125 115 Type Thread Code M2 M2.5 M3 S CLS Shank Code 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 00 0 1 2 00 0 1 2 1 2 1 2 1 2 1 2 Test Sheet Material 5052-H34 Aluminum Cold-rolled Steel 5052-H34 Aluminum Cold-rolled Steel 5052-H34 Aluminum Installation (kN) 6.7-8.9 11.2-15.6 11.2-13.5 13.4-26.7 11.2-13.4 18-27 Pushout (N) 280 400 750 470 550 1010 280 400 840 480 570 1210 300 470 970 490 645 1250 300 480 845 530 800 1112 750 970 1580 900 1380 1760 1570 1870 1760 2020 Torque-out (Nm) 0.9 1.13 1.47 1.47 1.7 2.03 1.8 1.92 2.5 1.8 2.3 2.3 2.37 2.6 4 2.95 4 5.1 3 3.6 5.7 3.6 4.5 6.8 6.5 7.9 10.2 14.1 10 13 17 13.6 18.1 18.7 20.3 32.7 36.2
S CLS
2500-3500
2500-3000
S CLS
M3.5
S CLS
632
S CLS
832
UNIFIED
SS CLSS
024 032
S CLS
1224
S CLS
0420
S CLS
0518 0524
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
M4 2500-3000 METRIC Cold-rolled Steel 5052-H34 Aluminum Cold-rolled Steel 5052-H34 Aluminum 4000-6000 SS CLSS M5 Cold-rolled Steel 5052-H34 Aluminum 2500-3500 Cold-rolled Steel 5052-H34 Aluminum 4000-9000 S CLS M6 Cold-rolled Steel 2500-6500 6000-8000 S CLS M8 Cold-rolled Steel 5052-H34 Aluminum 4000-7000 S CLS M10 5052-H34 Aluminum Cold-rolled Steel 5052-H34 Aluminum Cold-rolled Steel Cold-rolled Steel 5052-H34 Aluminum 315 6000-8000 400 150 4000-7000 380 120 5052-H34 Aluminum 5000-8000 400 270 UNIFIED Cold-rolled Steel 6000-8000 420 160 165 180
3000-6000
S CLS
11.2-15.6 18-38
18-32
22-36 32-50
TYPE H
Type H
sa l
S CLS
0616 0624
Cold-rolled Steel
.090 5052-H34 Aluminum .088 Cold-rolled Steel Test Sheet Thickness and Sheet Material
7000-11000
320 350 735 METRIC Type H Thread Code M10 Installation (kN) 22 33
S CLS
0813 0820
(1) Installation, pushout, and torque-out values reported are averages when all installation specifications and procedures are followed. Variations in mounting hole size, sheet material, and installation procedure will affect this data. Performance testing of this product in your application is recommended. We will be happy to provide samples for this purpose.
PennEngineering www.pemnet.com
CL-9
SL UNIFIED SL SL
SL SL
032 0420
21 35
1.65 3.75
Type
Thread Code
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
Locking Specifications (1) Test Sheet Material Shank Code 1 2 1 2 1 Max. Torque (1st thru 3rd) (Nm) 0.67 1.2 Min. Torque (1st thru 3rd) (Nm) 0.04 0.08 5052-H34 Aluminum Pushout (N) 400 750 400 840 470 Installation (kN) 6.7 - 8.9 Torque-out (N m) 1.13 1.47 1.92 2.5 2.6 4 Installation (kN) Pushout (N) 550 570 645 1010 1210 11.2 - 15.6 13.4 - 26.7 18 - 27 11.2 - 13.5 2 2.1 0.13 11.2 - 13.4 970 1250 800 1 2 1 2 2.4 4 0.18 0.30 11.2 - 15.6 18 - 32 480 3.6 845 5.7 18 - 38 27 - 38 1112 1760 1760 1580 1580 10.2 14.1 Test Sheet Material 304 Stainless Steel 304 Stainless Steel 304 Stainless Steel 304 Stainless Steel 304 Stainless Steel Test Sheet Material 304 Stainless Steel 304 Stainless Steel 304 Stainless Steel 304 Stainless Steel UNIFIED Installation (lbs.) 8000 9000 10000 8500 9500 10500 9000 10000 11000 9500 10500 11500 13500 Pushout (lbs.) 130 165 290 140 170 340 145 180 360 180 230 400 450 Pushout (N) 575 725 1290 645 800 1600 800 1025 1775 2000 Torque-out (in. lbs.) 14 17 18 18 24 28 30 37 45 35 45 60 150 Torque-out (Nm) 1.58 1.92 2.03 3.38 4.18 5.08 3.95 5.08 6.77 17
Cold-rolled Steel Torque-out (N m) 1.7 2.03 2.3 2.3 4 5.1 4.5 6.8 17 17
SL METRIC SL SL SL SL
M3 M3.5 M4 M5 M6
(1) 3 cycle locking performance. PEM spec PRS-C90 Max. on / Min. off torque for 1st thru 3rd cycles.
TYPE SP
Type SP UNIFIED SP SP SP SP Type SP SP SP SP Thread Code 440 632 832 032 0420 Thread Code M3 M4 M5 M6 Shank Code 0 1 2 0 1 2 0 1 2 0 1 2 1
TYPE SMPS
Type
sa l
Test Sheet Material Cold-rolled Steel Installation Pushout Torque-out (lbs.) (lbs.) (in. lbs.) 1500 1800 2000 35 60 65 Test Sheet Material Cold-rolled Steel Installation (kN) 7.5 8 8.8 Pushout (N) 156 267 289 Torque-out (Nm) 1.13 1.35 1.58 8 12 14
Shank Code 0 1 2 0 1 2 0 1 2 1
METRIC
Type METRIC
CL-10
PennEngineering www.pemnet.com
INSTALLATION
Type SP(1) - Identified With Stamp
1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into the recommended counterbored anvil hole and place the mounting hole over the shank of the fastener as shown in diagram. 3. With punch and anvil surfaces parallel, apply squeezing force until the head of the nut comes into contact with the sheet material.
Anvil Dimensions (in.) P +.000 R .001 Max. .064 .010 .064 .010 .082 .010 .082 .010 .163 .010
UNIFIED
PUNCH
(1) To meet the published performance data, we recommend using the installation punch and anvil shown. Deviations from recommended installation tooling may result in sheet distortion and reduced performance. NOTE: Variations in hole preparation, installation tooling, installation force, and sheet material type, thickness, and hardness will affect both performance and tooling life.
A special punch with a pilot pin to align the nut and a special anvil with a pilot pin to align the sheet and a raised ring is required to create a proper installation. The raised ring acts as a second displacer of the stainless sheet material, thereby ensuring proper installation. 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place sheet on raised ring anvil. 3. Place fastener in hole. 4. With punch and anvil surfaces parallel, apply squeezing force until the head of the nut comes into contact with the sheet material.
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
Anvil Part No. 8012821 8012822 8012823 8012824 8012825
Anvil Dimensions (mm) P R R1 0.03 Max. +0.13 1.63 0.25 0.13 1.63 0.25 0.13 2.08 0.25 0.13 2.08 0.25 0.13 4.14 0.25 0.13
METRIC
ANVIL
PUNCH
ANVIL
P unch Dimensions (in.) A P R R1 .002 .001 Max. +.005 .255 .066 .010 .005 .286 .066 .010 .005 .317 .089 .010 .005 .348 .089 .010 .005
sa l
UNIFIED
Anvil Dimensions (in.) B P1 (2) R2 A1 Thread Code .002 Nom. +.001 -.000 Max. 440 .199 .261 .009 .003 632 .218 .280 .009 .003 832 .243 .305 .009 .003 032 .288 .350 .009 .003 0420
Punch Dimensions (mm) P R R1 Thread A Code 0.05 0.03 Max. +0.13 M3 6.48 1.42 0.25 0.13 M3.5 7.26 1.42 0.25 0.13 M4 8.05 1.93 0.25 0.13 M5 8.84 1.93 0.25 0.13 M6 METRIC
P
Punch Part No. 8002695 8002696 8002697 8002698 (3)
R1
Anvil Dimensions (mm) B P1 (2) R2 A1 Thread Code 0.05 Nom. +0.03 Max. M3 5.05 6.63 .23 .08 M3.5 5.54 7.11 .23 .08 M4 6.17 7.75 .23 .08 M5 7.34 7.75 .23 .08 M6 METRIC
P1
R2
Sharp. No burrs
(1) To meet the published performance data, we recommend using the installation punch and anvil shown. Deviations from recommended installation tooling may result in sheet distortion and reduced performance. (2) We recommend replacing installation anvil when the height of the P1 dimension is reduced to .005 / 0.13mm due to wear. Reductions in performance may occur as the height of the protrusion wears. (3) Special installation tooling for #0420 and M6 thread sizes is not required. NOTE: Variations in hole preparation, installation tooling, installation force, and sheet material type, thickness, and hardness will affect both performance and tooling life. PennEngineering www.pemnet.com
CL-11
INSTALLATION (continued)
Types S, SL, SMPS, SS, CLS, CLSS, CLA, H, HN, and HNL
PUNCH
1. Punch or drill properly sized mounting hole in sheet. Do not perform any
secondary operations such as deburring.
2. Place fastener into the anvil hole and place the mounting hole over the shank of
the fastener as shown in diagram to the right.
3. With punch and anvil surfaces parallel, apply squeezing force until the head of
the nut comes into contact with the sheet material.
ANVIL
PEMSERTER PRESSES
For best results we recommend using a PEMSERTER press for either manual or automatic installation of PEM type S ,SL, SMPS, SS, CLS, CLSS, CLA, H, HN, HNL, and SP nuts. For more information on our line of presses call 1-800-523-5321, or check our web site.
Meets Torque Requirements Zinc per for IFI 100/ ASTM 107 Grade B 3 Cycle Precipita- Zinc per B 633 Zinc per (unified) and Locking tion Passivated ASTM SC1 (5m), ASTM ANSI B18. Perfor- Heat 300 Hardening and/or B 633 Type III, B 633 16.1M mance Treated Series 2024-T4 Grade Tested SC1 (5m), Colorless No SC1 (5m), (metric) PEM spec Carbon Stainless Alumi- Carbon Stainless per ASTM Type III, Plus Sealant/ Finish Type II, Locknuts PRS-C90 Steel Steel num Steel Steel Colorless Lubricant (2) (3) Yellow A380
S SL SMPS
es Fo @ r lo ac w ei es nd t p su ric pp es lie : s. co m
Fastener Materials Standard Finishes Optional Finishes (1)
Cadmium Spec SAE AMS- 90 or QQ-P-416, Less 80 or 70 or 60 or 50 or Type I, on the Less Less Less Less Class 3, Rockwell on the on the on the on the Plus Clear B Rockwell Rockwell Rockwell Rockwell Chromate Scale B B B B Passivation (4) (5) Scale Scale Scale Scale
SS
CLS CLSS CLA H HN HNL SP
ZI LZ X ZC
None
CI
Special order with additional charge. Part numbers for aluminum nuts have no plating suffix. Unplated threads are sized to accept a basic go guage after .00025 plating. Panel material should be in the annealed condition. Fasteners should not be installed adjacent to bends or other highly cold-worked areas.
sa l
Specifications subject to change without notice. Check our website for the most current version of this bulletin.
CL-12
CAGE-46384