Professional Documents
Culture Documents
Solvalitt Midtherm
Product description
Solvalitt Midtherm is a mid temperature resisting paint based on acrylic modified silicone resins.
Recommended use
To be applied over steel substrate or over inorganic zinc silicate primer as topcoat for steelwork operating at temperature up to 260C.
Physical properties
Colour Solids (vol %)* Flash point VOC Aluminium, Black, Red, White 34 2 Aluminium 40 2 Colours 27C 2 Aluminium 4,85 lbs/gal (580 gms/ltr) USA-EPA Method 24 545 gms/ltr UK-PG6/23(97). Appendix 3 Colours 4,47 lbs/gal (535 gms/ltr) USA-EPA Method 24 500 gms/ltr UK-PG6/23(97). Appendix 3 Aluminium sheen/Flat Good Very good
Solvalitt Midtherm
Page 1 of 4
Surface preparation
All surfaces should be clean, dry and free from contamination. The surface should be assessed and treated in accordance with ISO 8504. Bare steel Cleanliness: Blast cleaning to Sa 2 (ISO 8501-1:2007). Roughness: using abrasives suitable to achieve grade Fine to Medium G (30-85 m, Ry5) (ISO 8503-2) Coated surfaces Cured and clean zinc silicate primer. Other surfaces The coating may be used on other substrates. Please contact your local Jotun office for more information.
Application methods
Spray Brush Use airless spray or conventional spray Recommended for stripe coating and small areas, care must be taken to achieve the specified dry film thickness.
Application data
Mixing ratio (volume) Thinner/Cleaner Guiding data airless spray Pressure at nozzle Nozzle tip Spray angle Filter Note 15 MPa min (150 kp/cm2, 2100 psi) 0.38 - 0.48 mm (0.015 - 0.021") 40 - 60 Check to ensure that filters are clean. It is recommended to thin the paint by 5% with Jotun Thinner No. 7 when using conventional spray. Single pack Jotun Thinner No. 7
Drying time
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will be affected correspondingly. The figures given in the table are typical with: * Good ventilation (Outdoor exposure or free circulation of air) * Typical film thickness * One coat on top of inert substrate
Solvalitt Midtherm
Page 2 of 4
Substrate temperature Surface dry Through dry Dry to recoat, minimum Dry to recoat, maximum
1
5C 45 min 4h 6h
10C 30 min 3h 3h
23C 15 min 2h 2h
40C 10 min 1h 1h
Solvalitt Midtherm
Page 3 of 4
The surface should be dry and free from any contamination prior to application of the subsequent coat.
The given data must be considered as guidelines only. The actual drying time/times before recoating may be shorter or longer, depending on film thickness, ventilation, humidity, underlying paint system, requirement for early handling and mechanical strength etc. A complete system can be described on a system sheet, where all parameters and special conditions could be included.
Storage
The product must be stored below 25C and in accordance with national regulations. Storage conditions are to keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.
Handling
SHELF LIFE: 24 months at 23C. Higher temperatures during storage may reduce the shelf life and may lead to gelling in the tin. Handle with care. Stir well before use.
Packing size
5 litre container.
ISSUED 26 NOVEMBER 2010 BY JOTUN THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED
Solvalitt Midtherm
Page 4 of 4