Professional Documents
Culture Documents
VERSION 9
www.rimtec.com.au
Contents
small bore valves large bore valves super large bore valves z-bore valves mega bore valves special application valve air chucks valve tools tread depth gauges automatic tyre ination systems inators inator adaptors tyre pressure gauges hydraulic bead breakers hydraulic rams and jacks impact wrenches torque wrenches miscellaneous products wheel chocks wheel nut indicators tyre tting tools o-rings for tubeless tyres l-ring seals for em rims tube and tyre repair materials wheel weights and accessories hubodometer tyre sealants and lubricants notes 4 9 14 17 18 20 21 22 24 25 26 28 30 34 36 37 38 39 40 41 42 43 44 45 50 51 52 55 52
SYSTEM COMPARISONS
This product bulletin will compare and contrast the four tyre systems available from Haltec. Listed below is a chart with general characteristics of the four valve systems. Flow rates on the Super Large Bore, Z-Bore and Mega Bore Valves were tested with a 750 CFM diesel-powered air compressor with the pressure held constant at 100psi.
Valve System Large Bore Super Large Bore Z- Bore Mega Bore
*Flow rate is without valve core installed. With core, flow rate is 12 CFM.
FLOW DIAMETERS
Shown below is a cross section of the dierent ow diameters on the four valve systems.
LARGE BORE
0.19/4.826mm
Z-BORE
0.56/14.224mm
MEGA BORE
0.69/17.526mm
Valve System Spuds Standard Clamp-In Outside-In Clamp-In Screw-In Swivel Valves and Angle Connectors Swivel Valves Swivel Angle Conn. Extensions Rigid Brass Hand-Bendable Flexible Core Housings Core Housings Miscellaneous Caps Adapters To maximize flow, use Inflator:
x 1H-Z3 Series
x 1H-MB19 Series
NA x ZBV Series
NA x MBV Series
1H-R520
1H-Z10
1H-MB14
1H-A149, Various
1H-MB13
Remove Core
1H-MB8
SAFETY PRECAUTION
These products, as well as all the tyre tools, should never be used by persons unless they have been trained properly according to O.S.H.A Regulation #29CFR 1910.177 entitled Servicing Single-Piece and Multi-Piece Wheels.
www.rimtec.com.au
1V-587 L A
TR-413
1V-587b
TR-418
1V-587k
TR-412
1V-588
TR415
1V-521
1V-725 - 727
WWW.RIMTEC.COM.AU
1V-8102
1V-8110
TR No V3-20-1 V3-20-3
L 1.42 3.35
A 1.97 0.98
B 0.98 2.36
Deg 42 27 27
WWW.RIMTEC.COM.AU
1V-8834
1V-8844B
D 0.96 0.95
E 0.55
1V-2414 - 2530
1V-2412
1V-2612/90
RIGID EXTENSIONS
A 1.18 1.97 2.52 2.91 3.94 5.12 5.98 0.87 L 1.57 2.36 2.91 3.31 4.33 5.51 6.38 1.38 Rimtec Part No 1V-2412 1V-2414 1V-2416 1V-2418 1V-2422 1V-2426 1V-2530 1V-2612/90 Order Qty Each Each Each Each Each Each Each Each
WWW.RIMTEC.COM.AU
1V-621A - 625A
1V-660A
FLEXIBLE EXTENSIONS
L 5.91 6.89 9.84 11.81 4.92 Rimtec Part No 1V-621A 1V-622A 1V-624A 1V-625A 1V-660A Order Qty Each Each Each Each Each
WWW.RIMTEC.COM.AU
1V-990
1V-993 - 994
1V-594
AIR/WATER VALVES
TR No 618A 621A 622A CH3 L 2.13 1.67 1.89 2.95 4.53 65 90 A B Deg Rimtec Part No 1V-990 1V-993 1V-994 1V-594 Order Qty Each Each Each Each
1V-051
1V-053/1
1V-430/1
WWW.RIMTEC.COM.AU
1H-H41
XX-CC057
1H-C10
1H-H41 Tubeless Spud (TR SP-2) - Fits 13/16 rim hole used with all swivel Large Bore valves. XX-CC057 Clamp-In Spud - Can be removed and replaced without dismounting tyre. Use 5/16 Allen wrench to hold spud
while installing.
1H-C10 Screw-In Spud (TR SP-3) - Screws in to a 1/2 NPT tapered hole in the rim. Can be replaced without dismounting tyre. L
1H-WH44-Length
SWIVEL VALVES
TR No J-650 J-657 WH44-4 WH44-6 WH44-7 J4000-3.1/2 J4000-4.1/2 J4000-5 J4000-6 J4000-8 J4000-9 J4000-10 J4000-12 J4000-24 Description S/Bend Swivel S/Bend Swivel Straight Swivel Straight Swivel Straight Swivel S/Bend Swivel S/Bend Swivel S/Bend Swivel S/Bend Swivel S/Bend Swivel S/Bend Swivel S/Bend Swivel S/Bend Swivel S/Bend Swivel L 3.1/8 4 4 6 7 3.1/2 4.1/2 5 6 8 9 10 12 24 H 1.5/16 1.5/16 1.5/54 1.5/54 1.5/54 1.5/54 1.5/54 1.5/54 1.5/54 1.5/54 1.5/54 Deg 80 80 90 90 90 90 90 90 90 90 90 Rimtec No 1H-WH300/J650 1H-WH300/J657 1H-WH44/04 1H-WH44/06 1H-WH44/07 1H-WH45/03.5 1H-WH45/04.5 1H-WH45/05 1H-WH45/06 1H-WH45/08 1H-WH45/09 1H-WH45/10 1H-WH45/12 1H-WH45/24 Order Qty Each Each Each Each Each Each Each Each Each Each Each Each Each Each
WWW.RIMTEC.COM.AU
Deg 60 90 60 90
1H-WH75/J663
XX-MM022
1H-114S/5.5
TR No J-690 -
Description Triple Bend Swivel Valve Triple Bend Swivel Valve Turret Valve
L 25 4.69 5.1/2
H 1.5/64 0.56 2
WWW.RIMTEC.COM.AU
XX-CC001
1H-WHD7103EC
1H-WHG1450VC
1H-WHG8018VC 1H-WHG8019VC
Description Custom Bent Extension Custom Bent Extension Custom Bent Valve Custom Bent Valve Custom Bent Valve Custom Bent Valve
Bends 4 4 5 5 4 1
1H-T670 - Loader Tyre Valve complete with core, hex cap, and o-ring seal. 1H-H47- Screw In Type Valve with 1/4 male pipe
thread. Complete with core and cap.
1V-921
1H-T670
1H-H47
1H-H43
1V-908
WWW.RIMTEC.COM.AU
11
Description Rigid Brass Extensions Rigid Brass Extensions Rigid Brass Extensions Rigid Brass Extensions
L 3 6 7.1/4 8
FLEXIBLE EXTENSION
Made with tough rubber hose and reusable hydraulic type ttings. Equipped with 2 lock nuts and 3/4 hex sealing nut. A teon gasket seals on end of valve. The lead seal in the sealing nut is forced in to the threads for a second seal, positively locking extension to valve. Cap and core are not included - they should be removed from valve and transferred to extension. Any length can be ordered.
1H-810F
Description LB Flexible Valve Extension LB Jam Nut LB Hex Nut LB Valve Body LB End Connector LB Sleeve LB Valve Cap LB Valve Core
Rimtec Part No 1H-810F 1H-463 1H-464 1H-E1700/4 1H-E1700/5 1H-E1700/6 1V-059 1H-A145
Order Qty Each Each Each Each Each Each Each Each
WWW.RIMTEC.COM.AU
Description Hand Bendable Extension Hand Bendable Extension Hand Bendable Extension Hand Bendable Extension Hand Bendable Extension Hand Bendable Extension Hand Bendable Extension Hand Bendable Extension Hand Bendable Extension Hand Bendable Extension
L 3.1/2 4 4.1/2 6 8 10 12 16 18 24
Rimtec No 1H-753S/03.5 1H-753S/04 1H-753S/04.5 1H-753S/06 1H-753S/08 1H-753S/10 1H-753S/12 1H-753S/16 1H-753S/18 1H-753S/24
Order Qty Each Each Each Each Each Each Each Each Each Each
1V-059
1V-067-R
1H-A145
1V-440
1V-655/58
1V-656/58
Description LB Valve Cap with Slot LB Hexagon Head Valve Cap LB Valve Core Short LB Valve Core Long Inside LB to SB Adaptor Outside LB to SB Adaptor
WWW.RIMTEC.COM.AU
13
1H-K665 can be changed without dismounting tyre. Fits 13/16 rim hole. Use 1H-A325 3/8 Allen wrench to hold spud while installing. Do not use in continuous service. Temporary use only.
1H-T81
1H-T82
1H-K665
SCREW-IN SPUDS
1H-C100-R is used to attach any of the Super Large Bore valves
to the rim and is designed to screw in to a 1/2 NPT tapped rim hole. The spud can be changed without dismounting the tyre. 1H-C100-R has internal thread for core housing.
1H-S85 angle screw-in spud ts 1/2 NPT tapped rim hole. 85 degree bend angle. 1H-S60 has 60 degree bend angle. 1H-C100-R 1H-S85D is similar to the 1H-S85 but with a locking nut with
Teon seal XX-BB065 so direction can be reversed.
1H-S85 / 1H-S60
1H-S85D
1H-R675
1H-R525
Description SLB Swivel Angle Connector SLB Swivel Angle Connector SLB Swivel Angle Connector SLB Swivel Angle Connector SLB Swivel Angle Connector
Deg 90 80 60 75 85
WWW.RIMTEC.COM.AU
Extension Length
1H-MT3000
1H-R763
1H-R762S
1H-R764R
1H-B222
1H-R520
1H-R969K consists of 1H-R520 Core Housing, 1H-R762S Swivel Connector, 1H-R763 Straight Tubing Connector, 1H-R764R (2) Tubing Connector Sleeves and 1H-B222 Nuts (3). 1H-R969K-1 consists of the above less the 1H-R520 Core Housing.
The 1H-R969K and 1H-R969K-1 kits are available to eld assemble your own exible extensions with the 1H-T620 assembly tool.
NEW
1H-R760
(NOTE: Wire Braided reinforced hose also available)
1H-A450 Order Qty Each Each Each Each Each Each Each Each
Description SLB Valve Protector Cap SLB Straight Connector SLB Swivel Connector SLB Connector Sleeve SLB Lock Nuts SLB-LB Valve Core Housing SLB Flexible Extension Hose SLB Flexible Extension
Rimtec Part No 1H-A450 1H-R763 1H-R762S 1H-R764R 1H-B222 1H-R520 1H-R760 1H-MT3000
WWW.RIMTEC.COM.AU
15
1H-DS210
1H-DS215
1H-DS226
1H-MR800
1H-N1066
1H-R372
1H-M5000
1H-N1066 Loader Valve - Accepts 1H-R520 core housing or other SLB swivel ttings. Thread size is 1.1/16-12. 1H-R372 - Fits 1H-T81, 1H-C100-R and TR SP 816 Tube Spud. Air/Liquid valve for tractor and grader. 1H-M5000 Valve Assembly - Screw-in type spud with o-ring seal. 1H-R520 Core Housings not interchangeable in other
SLB spuds. Thread size is 3/4-16.
WWW.RIMTEC.COM.AU
Z-Bore Valves
Z-Bore Valves
Z-Bore ows 370 CFM compared to 240 CFM on the Super Large Bore Valve System.
Extension Length
1H-Z-1
1H-Z-2
1H-Z-4
1H-Z-3
1H-Z2-2 ZB Nuts
1H-Z100 ZB Tubing
WWW.RIMTEC.COM.AU
17
1H-MB-12-85
1H-MB-20
1H-MB-19-85
1H-MB-14
1H-MB-13 Valve Cap - Cap for the Mega Bore core housing.
Protects core housing from damage. Has an o-ring seal.
1H-MB-8 Inator - Attaches to the valve body by turning the knurled nut on the inator in a clockwise direction. The 3/4 ball valve is used to open and close the air ow after the core housing is retracted with the 1H-TL-700. 1H-MB-13 1H-TL-700 Tool - Fits the mega bore core housing to retract the
housing for ination and deation. The 1H-TL-700 should be used only in conjunction with the 1H-MB-8 Mega Bore inator. The 1H-MB-8 inator should be engaged on the core housing before using the 1H-TL-700.
1H-MB-8
1H-TL-700
Description MB Screw-In Spud MB Clamp-In Spud MB Angle Connector MB Rigid Valve MB Valve Cap MB Tool MB Inflator
WWW.RIMTEC.COM.AU
Length Mega Bore Flexible Valve - Screws into the Mega Bore angle connectors or screw-in angle spud. Can be made up in any legth (minimum 8). The specially designed ttings and thermoplastic hose will not crush or fatique during service. Large Bore threads on the core housing allow use of Large Bore pressure gauges and air chucks. Screws into the Mega Bore angle connectors or screw-in angle spud. Made to length in the eld using MBAT assembly tool. MB-14 screws into the end to complete the valve.
WWW.RIMTEC.COM.AU
19
Special Application
20
Special Application
1H-H7607
1H-H798
1H-H7607 - For operating pressure to 2,000 psi. 1H-H798 - For operating pressure rated to 5,000 psi.
1H-H556
1H-H6116B
1H-H556 - Fits 0.305-32 thread size with 1/8 NPT male connection. Has core depressor pin, and copper sealing washer. Maximum working pressure 3000 psi. 1H-H2755 - Fits 0.305-32 thread size with 3/8-24 thread for 3/16 are tube tting. Has core depressor pin and copper sealing washer. Maximum working pressure 3000 psi. 1H-H6116B - Fits 0.305-32 thread size with 1/8 with 1/8 NPT female connection with 70 degree bend. Equipped with hard bre sealing washer. Used up to 3000 psi working pressure.
WWW.RIMTEC.COM.AU
1H-CH330-LO
1H-CH335
1H-322
1H-377
1H-CH330-LO Small Bore Dual Foot Air Chuck - Is a straight-on 30 degree reverse angle chuck. Available with the lock-on feature. Has 1/4 NPT female thread. 6 long. 1H-CH335 Small Bore Dual Foot Air Chuck - Is designed for hard to reach tractor, dual wheel trucks and bus tyres. 1/4 NPT female threads. For standard air line service. 6 long. 1H-322 Large Bore Dual Foot Air Chuck - Is a 45 degree angle chuck allowing easy access to the tyre valve. Has 1/2 NPT female
thread.
1H-377 Large Bore Lock-On Air Chuck - Locks on valve when cocked on threads. Has greater air ow and seat can not be blown out
if seat fails. Has 1/4 NPT female thread.
1V-3031/8
1H-CH340 1H-H4660A
1H-CH315
1W-N282
1H-6190
1W-N282 Small Bore Clip-On Air Chuck - Fits 1/4 ID hose-open style. 1H-CH315 Small Bore Ball Foot Air Chuck with Clip - With 3/4 hex, brass with 1/4 NPT female thread. Heavy-duty spring rmly holds chuck on to valve while inating tyre.. 1H-CH340 Small Bore Lock-On Air Chuck - Securely locks on to valve when sleeve is pushed forward, releases when sleeve is pulled back. 1/4 NPT female thread. 1V-3031/8 Small Bore Clip-On Air Chuck - Closed type chuck. Has serrated 8mm shank for 1/4 ID hose.. 1H-H4660A Large Bore Clip-On Air Chuck - Securely locks on to valve when sleeve is pushed forward, releases when sleeve is pushed back. Has 1/4 NPT female thread. 1H-6190 Large Bore Quick-Connection Ination Chuck - Designed specically for use with XX-E031 check valve and permits
unrestricted air ow. Gauging can be done through valve on chuck. Positive air line shut o valve must be installed in back of air chuck.
WWW.RIMTEC.COM.AU
21
Valve Tools
Bore.
valve tools
1H-TL610
1H-TL690
1H-TL680
1H-TL610 Small Bore 4-Way Valve Tool - Repairs and reconditions inside and outside valve threads. Inserts and removes cores. 1H-TL690 Large Bore 4-Way Core Tool - Thread repair for core and cap threads and core remover. For Large Bore and Super Large 1H-TL680 Large Bore 3-Way Valve Tool - For removing Large Bore cores, hex caps and screw driver caps.
22
WWW.RIMTEC.COM.AU
Valve Tools
valve tools
1H-TL631
1V-672
1H-N1810
1V-680
1H-T620
XX-B048
1H-ASP1
1H-TL631 Super Large Bore Rethreading Tool - Used to rethread 11/16-24 thread on any SLB valve. 1V-672 Valve Stem Installation Tool - Rugged Small Bore tool handles any length valve in nay size rim. Screws over valve threads and quickly installs valve in to valve hole by applying pulling pressure. 1H-N1810 Large Bore Hex Cap Remover - With plastic handle for positive grip-OAL 10. 1V-680 Small Bore Valve Fishing Tool - Combines valve core wrench and deating pin with exible cable for shing valve through rim hole. 1H-T620 Super Large Bore Assembly Tool - Used for eld assembly of SLB exible extensions. XX-B048 Deation Aspirator - Tube deation aspirator for Large Bore. 1H-ASP1 Deation Aspirator - Tube deation aspirator for Small Bore.
WWW.RIMTEC.COM.AU
23
1H-N1420H
1H-GA190 Tyre Tread Depth Gauge - Quickly and accurately measures how much tread is left on tyre. Calibrated in 1/32 units and millimetres. Chrome plated brass with pocket clip.
1H-GA190
1H-N1410-R
WWW.RIMTEC.COM.AU
IDEAL FOR QUICK LUBE CENTRES, RENTAL CAR FACILITIES AND AUTOMOBILE DEALERSHIPS
1H-89XDA Heavy Duty Digital Tyre Inator
The heavy duty, weatherproof and vandal resistant enclosure of the 89XDA makes it ideal for almost any indoor or outdoor location Inates or deates automatically Accurate to within 0.3 psi 1/4 inlet and outlet Self calibrates every 6 minutes Can be customized to any corporate image and language text
1H-89XDA
IDEAL FOR FLEET OPERATIONS, TYRE SERVICE CENTRES AND TYRE MOUNTERS
1H-89XDB Heavy Duty High Volume Tyre Inator System
Designed specically for inating large tyres or multiple truck tyres Indoor or outdoor use Inates 1 to 4 tyres simultaneously 1/2 inlet maximizes air ow Accurate to within 0.3 psi
1H-89XDB
IDEAL FOR RETREAD CENTRES, TYRE SERVICE CENTRES AND TYRE MOUNTERS
1H-89XDZ Over Ination Tyre System
Utilizes 1/2 inlet maximizing air ow Equipped with emergency stop control Accurate to within 0.3psi Dual LCD screens Preset feature stores the 3 most common pressure settings Leak detection test Multiple surge cycle setting Indoor or outdoor use
TECHNICAL SPECIFICATIONS
Construction Power Requirement Unit of Mesurement Operating Range Operating Temperature Die Cast Aluminium Enclosure or Polycarbonate Enclosure 110V a.c. or 12V d.c. 1 psi, kpa & bar available 5-145 psi (other ranges available) 14 F to 122 F (-4 F to 122 F with optional heater)
1H-89XDZ
WWW.RIMTEC.COM.AU
25
Inators
26
inators
1H-I401
XX-C105 (I402)
1H-I404
XX-C043 (I405)
1H-I401 Extra Heavy Duty Large Bore Inator with Straight Clip-On Chuck - 5 foot inator has 1/2 ball valve with provision for checking air pressure and 1H-H4660A straight lock-on-chuck. Inator has a 3/8 ID for maximum air ow. Threaded for 1/2 male NPT hose ttings. XX-C105 Series Safety Inator - Available in 6 foot length. Has pressure check valve for exact pressure check with your pencil gauge.
Has manual bleed valve for adjusting tyre pressure and XX-AA015 ow through clip-on air chuck.
1H-I404 Heavy Duty Dual Hose Inator - Has two separate clip-on chucks with 5 foot hoses. One chuck, XX-AA015, t Small Bore valves and the other, 1H-H4660A, Large Bore valves. Has spring loaded, hand operated valve and has provisions for checking air pressure during ination. Threaded for 1/4 male NPT hose ttings. XX-C043 Inating Gauge - Ination unit with in-line gauge. Lightweight aluminium body with brass movement and O-ring seals. Calibrated 10-120 psi in 2lb increments - precise ination control - 1/4 female NPT inlet. Hose length is 6 foot with XX-AA015 clip-on air chuck. Replacement cartridge is available. Also available with hose lengths of 3 and 9 foot.
WWW.RIMTEC.COM.AU
Inators
inators
1H-I406M
1H-I409
1W-N1991-R
1H-I406M Ination Gauge - Has 12 of hose and 1H-CH335 dual foot air chuck to service small diameter wheels. Gauge is calibrated 10-120 psi in 2lb increments. 1H-I409 Ination Gauge - Has 12 of hose and 1H-H4660A dual foot air chuck to service small diameter wheels. Gauge is calibrated
10-120 psi in 2lb increments.
1W-N1991-R SB Inating Gauge - Dual calibrated bar and psi (10-174). Hose length 150cm.
WWW.RIMTEC.COM.AU
27
Inator Adaptors
28
inator adaptors
1H-310 Valve Adaptor Gun - Has a 1/2 female pipe thread and will attach to any calcium tyre lling pump, it will extract from a Small Bore valve or the core housing from a tractor valve. It will securely hold the valve core housing up in the gun body during tyre lling or evacuation of liquid from a tyre. Due to the design, it will permit faster evacuation of liquid from a tyre than with other adaptor guns.
Parts List FP134 FP135 FP136 FP137 FP138 FP139 FP140 FP141F FP142 FP143 FP144 FP145 FP146 Large Bore Core Remover Adaptor for Standard Valve O-Ring for 1H-FP135 Adaptor Standard Valve Core Remover Ejector Union Gasket Stem Adaptor Body Stem Sealing Nut O-Ring for 1H-FP142 (Stem Seal) Hand Wheel Lock Nut Teon Gasket
1H-310
1H-307
Parts List FP135 FP136 FP138 FP139 FP141A FP142 FP143 FP144 FP145 FP146 FP153 FP154 FP155 FP156
Adaptor for Standard Valve O-Ring for FP135 Adaptor Ejector Union Gasket Adaptor Body Stem Sealing Nut O-Ring for FP142 (Stem Seal) Hand Wheel Lock Nut Teon Gasket Collet Adaptor Stem and Collet Snap Ring for FP153 Snap Ring for FP154
WWW.RIMTEC.COM.AU
Inator Adaptors
inator adaptors
1H-IN80A Super Large Bore Inator Adaptor
1/2 pipe thread for easy air hose connection. During ination, air pressure in the tyre can be checked through the stem knob with a tyre pressure gauge. Reduces ination time by 60%, deation time 80%. The core housing is held in a stainless steel extractor by a snap ring. Extractor is rugged enough so that the core housing can be loosened or tightened without being damaged. The 1H-IN80A inator adaptor saves time by fast ination or deation on a tyre. After removing the valve cap, the inator is screwed on to the valve stem. The inator stem is pushed in to engage the ats on the core housing. By rotating the stem counter clockwise, the core housing can be removed without any danger to the person removing it. The core housing is pulled up in to the inator body and held there during ination or deation. Can also be used for liquid-lling tyres equipped with Super Large Bore valves. Parts List 1H-G201 1HE-3100-4A 1H-G206 1H-8807N4 1H-E3100-1 1H-G202 1H-G204 1H-A145 1V-053/1 Ejector Union Adaptor Body Gasket for 1H-E3100-1 Cap Adaptor Complete Stem and Collet Gasket for 1H-G201 Snap Ring for Collet Large Bore Valve Core Standard Bore Cap
1H-IN80A
1H-AQF1 Aqua Quick Fill - A simple, time-saving tool that allows the user to ll a tractor tyre or large o-the-road tyre with liquid, and do other tasks while the tyre is being lled. No longer does the user have to stand by and vent the excess air pressure. With the 1H-AQF1, air is automatically vented through a side port while the liquid is being injected in to the tyre. When the tyre is lled, the water escapes from the vent hole, indicating that the tyre is full. 1H-AQF1
XX-E015 N1452 Nipple 1/2 NPT male thread. For fluid use. N1451 Coupler 1/2 NPT female thread. For fluid use.
XX-E016
WWW.RIMTEC.COM.AU
29
XX-LL011 XX-E065
1H-GA255
1H-GA250-R
XX-LL011 Pencil Tyre Gauge - 20-90 psi. For radial and light truck. XX-E065 Dual Foot Truck High-Pressure Gauge - 20-120 psi. 1H-GA255 Large Bore Swivel Foot Gauge - 10-150 psi. Also available with metal indicating bar. 1H-GA250-R Large Bore High-Pressure Gauge - 10-150 psi. Fits Small Bore and Large Bore valves. Also available with metal indicating bar.
WWW.RIMTEC.COM.AU
1H-N1055
1H-GA274
1H-GA290
1H-GA285
1H-N1055 Dial Gauge - Calibrated 0-160 psi in 5lb increments and 0-1100 kPa metric scale. Holds pressure read out until released.
Has 12 hose and 1H-CH335 dual foot air chuck. For truck service.
1H-GA274 SB/LB Air Liquid Gauge - Calibrated 0-160 psi in 5lb increments and 0-1100 in kPa metric scale. 14 exible hose.
Holds pressure readout until released.
1H-GA276 SB/LB Dial Gauge - Calibrated 0-160 psi in 5lb increments and 0-1100 in kPa metric scale. Overall length is 18.
Holds pressure readout until released. Come with bleeder valve. Similar to 1H-GA274.
1H-GA275 SB Dial Gauge - Calibrated (0 to 160 lbs.) in 5 lb. units and (150 to 1100 kPa) metric scale. 20 exible hose. 1H-GA290 SB/LB Air/Liquid Master Gauge - Straight-on air chuck ts both SB and LB valves. Has 12 exible hose to get to those
hard to reach valves. Calibration 0-160 psi in 1lb increments
1H-GA285 Dial Gauge with Rigid Extension - Calibrated 0-160 psi in 5lb increments and 0-1100 kPa metric scale. Features a
10 extension.
WWW.RIMTEC.COM.AU
31
1H-GA289
1H-N1510
1H-GA289 Dial Gauge - Calibrated 0-160 psi in 5lb increments and 0-1100 kPa metric scale. 1H-N1510 Cap Gauge - Fits Large Bore and Super Large Bore valves. Calibrated 0 to 160 psi in 5lb increments. Allows visual inspection of tyre pressure.
1W-N1976 1W-N1930
1W-N1930 Eurodainu SB and LB Dial Gauge - Dial Gauge with swivel chuck for both Small Bore and Large Bore valves. 1W-N1976 Dial Gauge - Small Bore Gauge, 0-60 psi.
WWW.RIMTEC.COM.AU
THE PT SYSTEM ALLOWS ACCURATE SETTING OF OPERATING PRESSURES BY MEASURING THE TYRES INTERNAL AIR TEMPERATURE AND THEN USING A CHART TO DETERMINE THE CORRECT PRESSURE LEVEL. THERE ARE 2 CHARTS USED: 1 IS A DRY PRESSURE TEMPERATURE CHART FOR TYRES FILLED WITH DRY AIR OR NITROGEN, THE OTHER A WET PRESSURE TEMPERATURE CHART FOR TYRES WHICH CONTAIN LIQUID SUCH AS SEALANT OR WATER.
WWW.RIMTEC.COM.AU
33
6I-1800
6H-OTR2000 6I-Y13
6I-210HP
6H-T10109
6I-1800 - IMTs 1800 OTR tyre bead breaker is designed for unseating tyre beads on 24-57 diameter earthmover rims that have either pry bar pockets or full recessed bead seat bands. It is designed with 4 stroke and more power for fewer hookups and reduced tyre changing time. The 1800 bead breaker weighs 12.7kg. 6I-210HP - The 210HP bead breaker works on all types of rims for tractor, truck, grader and implement tyres. Smooth dependable air/ hydraulic action breaks inside and outside beads in minutes without tyre removal. It is compact for easy storage and weighs only 12.24kg. 6H-OTR2000 - Designed for largest o-road tyres and rims. Works on all 39, 45, 51, 57 and 63 rim sizes. Can be used with Haltec model AHP15 or AHP20 pump or 6I-Y13. 6I-Y13 - IMTs high eciency, 5 litre capacity, air/hydraulic pump generates 10,000 psi of hydraulic output. It operates most eciently in
the 100 to 125 psi range of air pressure. The Y13 pump is designed to work with the 1800 and 210HP bead breakers. The Y13 pump comes complete with hydraulic connecting hose.
6H-T10109 - Works on both front and back wheel without dismounting wheel from vehicle. Works on all 3-pce 25 wheels or larger.
WWW.RIMTEC.COM.AU
OTR-3000
The OTR-3000 Bead Breaker will break even the most stubborn OTR beads. The OTR-3000 is designed to prevent the tool from kicking out OTR-3000 Bead Breaker requires unique jaws based on wheel type. Please specify wheel type and style before ordering.
NEW
6H-OTR3000
IMT 1000
The IMT 1000 Bead Breaker is designed for unseating tire beads on OTR tires up to 29-inch diameter. Specically, this tool can be used to break down dicult 3-piece earthmover rims with solid back ange/rim base assemblies and rims with lock ring retainers. Its adjustable clamping jaw accommodates larger OTR rim anges such as those on graders, wheel loaders and haul trucks. Smooth, dependable air/hydraulic action breaks inside and outside beads in minutes. The bead breaker assembly hydraulically clamps to the rim and pushes the tire bead away from the rim ange o the bead-seat. The lightweight 1000 bead breaker works on single and multi-piece rims. The 6I-Y13 air/hydraulic pump is required for operation. Weight 30 lb (13.6kg)
6I-51718925
WWW.RIMTEC.COM.AU
35
These rams are recommenced for use in pushing orear beads on earthmover wheels. Can be used for all earthmover tyre trucks. Can be used for all earthmover tyre trucks. Can also be used as a general purpose cylinder. Maximum operating pressure of 10,000 psi. Designed for use in all positions. Made in USA. A coupler and dust cap are included with all models.
Cylinder Effective Area (in2) 2.23 2.23 2.23 6.50 11.05 20.65
AJ30
XX-BB030
AJ30 - The AJ30 shorty is a light-weight low-prole design for use in conned places. Cylinder capacity is 30 tons. XX-BB030 - 50-ton aluminium jack is easy-to-handle and light-weight, it can be used with any 10,000 psi pump. Perfect for ohighway work. Comes with a 7 x 7 aluminium base.
WWW.RIMTEC.COM.AU
Impact Wrenches
impact wrenches
UW220P
UW251P
6J-UW-381
UW401L
ESTABLISHED IN 1915 AS THE PIONEER MANUFACTURER OF PNEUMATIC TOOLS IN JAPAN, URYU HAS BECOME SYNONYMOUS WITH QUALITY AND RELIABILITY
UW140P Series - Combine compact size and light weight design with high torque, 70-200Nm to meet a wide range of applications. Recommended for overall automotive service, body shops, etc. UW220P Series - Are recommended for fastening joints in general industry. UW251P Series - Are recommended for heavy industrial production work such as engine work, truck springs, tractor pads, o-road
equipment and farm equipment.
6J-UW-381 Series - Are powerful, light-weight impact wrenches that are ideal for wide applications (1400-2000Nm) in steel erection reneries, petrochemical plants, mines, steel mills and heavy motor vehicle plants.
All models available with extended anvils.
Rimtec Part No UW/140P UW/220P UW/251P UW/22S UW/032S UW/381 UW/381L UW/401
Order Qty Each Each Each Each Each Each Each Each
WWW.RIMTEC.COM.AU
37
Torque wrenches
38
torque wrenches
RAPTOR Pneumatic Torque Wrench
NEW HI-SPEED PNEUMATIC TORQUE WRENCH
Lightweight and Fast This new line provides continuous and repeatable torque with an accuracy of +/- 5%. RAPTOR series has the fastest speed when it counts, which is during actual torque and not only during free nut run down!
Torque range: 500 ~ 2,000 ft/lbs / 678 ~ 2,712 Nm Accuracy +/- 5% Repeatability 2% RPM 10 Weight 12.5 lbs / 6 Kg Noise Level 85 db Filter, Regulator, Lubricator in carry case for above tool
3 solid bar extensions to allow for various depths of rims: 100mm 175mm 250mm
WWW.RIMTEC.COM.AU
Miscellaneous Products
miscellaneous products
(5R-TYRESTAND) (XX-C131)
TYRE BRANDERS
DIE GRINDERS
TYRE RE-GROOVERS
MPI/NDT
BLO VACS
HOSE CUTTER
(XX-LL033)
WWW.RIMTEC.COM.AU
39
wheel chocks
A 40
wheel chocks
WWW.RIMTEC.COM.AU
The current available sizes are: 17mm 22mm 27mm 32mm 40mm 18mm 23mm 28mm 33mm 41mm 19mm 24mm 29mm 34mm 46mm 20mm 25mm 30mm 36mm 21mm 26mm 31mm 38mm
THE SIZE REFERS TO THE ACROSS THE FLATS DIMENSION OF THE WHEEL NUT HEXAGON IN MILLIMETRES.
A simple and accurate means of measuring the wheel nut size is to use an un-worn socket as it is important that the correct size of Checkpoint is tted to the wheel nut. They should be a tight slide t down to the washer of the wheel nut or wheel hub face leaving a small nominal (say 0.5 mm) air gap between the two surfaces. The size of the Checkpoint is moulded on the outer face of the Checkpoint on which can be seen a series of radial moulded numbers: In this example the moulded arrowhead below the 3,3 indicates that the Checkpoint is for use with a 33mm hexagon wheel nut. Where possible Checkpoint are supplied in frames of 10pcs for ease of handling and counting. All packs are labelled with the product
Safe
Unsafe
DUSTITE LR
The Dustite LR is a wheel nut dust cap indicator for use where wheel trims with wheel nut access holes have been tted. Until now, the tting of a wheel trim has made it dicult to eectively use the standard Dustite or Checkpoint Loose Wheel Nut indicator products. This long reach version of Dustite allows the indicator wheel nut cap to be mounted on the wheel nuts through the access holes in the trim so that the indicating pointers can be aligned on the outer surface of the trim and be visible at all times for walk-round safety and roadworthiness inspections and zero defect reporting.
NEW
WWW.RIMTEC.COM.AU
41
Thin Wall Deep Impact Socket Extension Bars can be locally manufactured to order.
6M-YTL600/T2
WWW.RIMTEC.COM.AU
PACKAGED 2 PER POLY BAG. 24 O-RINGS PER CASE. CONSISTENT PRODUCT QUALITY. QUALITY POLYISOPRENE RUBBER. INDIVIDUALLY MARKED IN AN EASY TO READ COLOUR. EXCEPTIONAL SPLICE STRENGTH
All sizes carried in stock are listed below. Other sizes available on request.
Description 24 O-Ring 25 O-Ring 25 O-Ring Thick 29 O-Ring 33 O-Ring 35 O-Ring 39 O-Ring 45 O-Ring 49 O-Ring 49 O-Ring Thick 51 O-Ring 57 O-Ring 63 O-Ring
Rimtec No 4H-OR224 4H-OR225 4H-OR325 4H-OR329 4H-OR333 4H-OR335 4H-OR339 4H-OR345 4H-OR349 4H-OR449 4H-OR451 4H-OR457 4H-OR463
Order Qty Pkt of 2 Pkt of 2 Pkt of 2 Pkt of 2 Pkt of 2 Pkt of 2 Pkt of 2 Pkt of 2 Pkt of 2 Pkt of 2 Pkt of 2 Pkt of 2 Pkt of 2
WWW.RIMTEC.COM.AU
43
Description 25 L-Ring Seal 29 L-Ring Seal 33 L-Ring Seal 35 L-Ring Seal 39 L-Ring Seal 45 L-Ring Seal 49 L-Ring Seal 51 L-Ring Seal 57 L-Ring Seal 63 L-Ring Seal
Rimtec No 4H-LR25 4H-LR29 4H-LR33 4H-LR35 4H-LR39 4H-LR45 4H-LR49 4H-LR51 4H-LR57 4H-LR63
Order Qty Each Each Each Each Each Each Each Each Each Each
Description Radial Bead Seating Ring Radial Bead Seating Ring Radial Bead Seating Ring
WWW.RIMTEC.COM.AU
TUBE PATCHES
Description Tube Repair Patches Round No. 0 x 30mm Tube Repair Patches Round No. 1 x 38mm Tube Repair Patches Round No. 2 x 48mm Tube Repair Patches Round No. 3 x 56mm Tube Repair Patches Round No. 4 x 75mm Tube Repair Patches Round No. 5 x 95mm Tube Repair Patches Round No. 6 x 116mm Tube Repair Patches Oval No. 7 x 76mm x 37mm Tube Repair Patches Oval No. 8 x 102mm x 44mm Tube Repair Patches Oval No. 9 x 160mm x 76mm Rimtec Part No 7P00 7P01 7P02 7P03 7P04 7P05 7P06 7P07 7P08 7P09 Order Qty 100 30 30 30 30 10 10 30 30 10
TYRE PATCHES
Tyre Size Bias Ply Tyre Patches PHD3 100mm 2ply Bias Ply Tyre Patches PHD4 140mm 4ply Bias Ply Tyre Patches PHD5 165mm 4ply Bias Ply Tyre Patches PHD6 235mm 6ply Bias Ply Tyre Patches PHD7 300mm 6ply Radial Tyre Patches MCX14 75mm x 120mm Radial Tyre Patches MSX10 50mm x 70mm Radial Tyre Patches MSX12 60mm x 105mm Radial Tyre Patches MSX20 75mm x 100mm Radial Tyre Patches MSX40 100mm x 190mm Radial Tyre Patches MSX42 130mm x 255mm Box 10 10 10 10 10 12 24 12 Rimtec Part No 7P-PHD3 7P-PHD4 7P-PHD5 7P-PHD6 7P-PHD7 7P-MCX14 7P-MSX10 7P-MSX12 7P-MSX20 7P-MSX40 7P-MSX42 Order Qty Each Each Each Each Each Each Each Each Each Each Each
WWW.RIMTEC.COM.AU
45
WWW.RIMTEC.COM.AU
7P-PF30 Truck Patch Repair Kit Consists of: 35 Assorted Tube Patches 3 Small Tyre Patches 1 x 100g Tube Solution 1 x Roller Buer Stitcher 3 SB Valve Cores 1 Plastic Kit Box
7P-SS3
7H-RK800
Tyre Size String Repair Kit LV Repair Strings LV String Repair Kit EM Repair String EM Probe Reamer LV String Insertion Tool LV String Insertion Tool Truck String Insertion Tool EM Truck Patch Repair Kit
Rimtec Part No 7P-SS3-R 7P-SS4 7H-RK800 7H-RK820 6P-219C 6W-N1460 6P-V252/4 6H-RK810 7P-PF30
Order Qty Each Pkt of 50 Each Each Each Each Each Each Each
WWW.RIMTEC.COM.AU
47
A&B Compound
Rapid Solution
Maxicement
Buffsol
Super Solution
Tyre Size A&B Compound 2 Part Rubber Putty 1kg Super Solution 20g Tube Super Solution 350g Tin (Tube Repair) Maxicement H/Duty Solution 350g Tin (Tyre Repair) Buffsol Solvent Cleaner 1ltr Tin Buffsol Solvent Cleaner 5lt Tin Rapid Solution 5kg Tin
WWW.RIMTEC.COM.AU
Knife
Paint Pens
B/Bearing Stitcher
Buffer Stitcher
Rasps
Paint Sticks
Description Flap Wheel 60mm x 30mm x 60g x 6mm Shank 4 Row Wire Brazing Brush Rasp Roller Buffer Stitcher B/Bearing Stitcher 38mm x 1.5mm Tyre Knife 7 Blade Diamond Cut Burr 6mm Diamond Cut Burr 9mm Diamond Cut Burr 11mm Round Face Rasp 50mm x 6mm x 3/8 x 36g Round Face Rasp 50mm x 13mm x 3/8 x 36g Contour Wheel 50mm x 3/8 x 16g Contour Wheel 50mm x 3/8 x 36g Contour Wheel 50mm x 3/8 x 60g Arbour to Suit UNF Thread Markal Paint Sticks White Markal Paint Sticks Yellow Artline Paint Pens White Artline Paint Pens Silver
Rimtec Part No 6T-603060 6T-4R/604 6T-B5 6I-001 6B-TK010 6P-RBS06 6P-RBS09 6P-RBS11 6G-S2001 6G-S2003 6I-TCW210NC 6I-TCW210NM 6I-TCW210NF 6G-R5/R6 7G-MARKALL B/W 7G-MARKALL B/Y 7S-PX20W 7B-A400S
Order Qty Each Each Set Each Each Each Each Each Each Each Each Each Each Each Pkt of 12 Pkt of 12 Each Each
WWW.RIMTEC.COM.AU
49
WWW.RIMTEC.COM.AU
Hubodometer
hubodometer
WHETHER FOR MAINTENANCE PURPOSES OR LOGGING MILES, ACCURACY IS CRITICAL. SO, IF YOUR HUBODOMETER DOESNT GIVE YOU AN HONEST, ACCURATE CALCULATION OF KILOMETRES TRAVELLED, YOURE LOSING MONEY AND PROFITS. STEMCO HUBODOMETER IS GUARANTEED TO DELIVER MILEAGE ACCURACY WITHIN =/-2% (BASED ON THE LIFE OF THE TYRE). WITH CONSTRUCTION SO DURABLE, WE BACK IT WITH A 500,000 MILE WARRANTY.
Tyre Size 14.00 x 24 24.00 x 35 27.00 x 49 30.00 x 51 33.00 x 51 36.00 x 51 37.00 x 57 40.00 x 57
Rimtec Part No XX-HH033 XX-DD021 6T-6500507 XX-E092 XX-E093 XX-BB080 XX-CC045 XX-CC046
Order Qty Each Each Each Each Each Each Each Each
WWW.RIMTEC.COM.AU
51
SEAL-A-WHEEL
WHEN OPERATING IN HARSH MINING CONDITIONS YOU NEED EVERY BIT OF HELP AVAILABLE
Seal-A-Wheel is a liquid tyre sealant and anticorrosive agent which minimises air leaks resulting from ineective sealing O rings, rim parts, tyre beads or liners. By adding Seal-A-Wheel to tyres which have been identied as leakers (or preferably to every tyre in service) downtime due to pressure maintenance will be minimised as tyres will not require continual reination. Tyres which may have required removal to rectify a leak can now be kept in operation. Tyre life will be improved as problems associated with under-inated tyres are reduced, e.g. heat separations, abnormal tread wear and impact failure (due to casing fatigue).
FEATURES:
ANTI-CORROSIVE NON-POISONOUS USE AS SUPPLIED. NO MIXING NECESSARY CONTAINS NO CHROMATE - SO NO CHROMATE EFFLUENT PROBLEMS NON-FLAMMABLE PROTECTS STEEL CORD IN TYRE SAFE TO HANDLE
BENEFITS: SEALS SMALL AIR LEAKS LESS RIM CORROSION MEANS TYRE STRIPPING IS EASIER REDUCES BLOCKED VALVES IDENTIFIES RIM CRACKS
Available in:
205 Litre Plastic Drums (Premix or Concentrate) 1000 Litre Containers (Premix or Concentrate)
Important Notice 1. Seal-A-Wheel must be applied in correct quantity to properly perform each function of sealing, cooling, rust and oxidation control, bead sealing etc, in order to provide total tyre and wheel protection. 2. Severely damaged inner-liners, extreme operating conditions, or badly rusted rims, may require an increase of up to 50% more than the recommended quantities.
WWW.RIMTEC.COM.AU
TYRE SEAL
MAKE YOUR TYRES GO THE DISTANCE STANCE
Industrial
Industrial strength Tyre Seal is a preventative maintenance solution for sealing tube and tubeless tyres within the tread area from punctures caused by objects up to 8mm diameter. Tyre seal helps maintain consistent tyre pressure by reducing air loss from rim, bead, porosity and puncture leaks. Industrial Tyre seal saves on repairs, tyre replacement, down time and costly call outs. In tubeless tyres tyre seal controls rim rust pitting and scaling thereby rendering removal and tting easier. Helps to extend casing life by conditioning the tyres inner surface. To minimize the risks of tube failure froma puncturing object (1) inspect tyre periodically to locate and remove objects that may cause a tube to split (2) Avoid overloading vehicle (3) Check that tyres are correctly inated (4) Ensure tted tubes are the correct size and not abnormally stretched inside the tyre.
WWW.RIMTEC.COM.AU
53
RIM SOAP
The most popular tyre tting lubricant on the market today. Being a soap based product, clean up is easy. It just washes o with water. No greasy sticky excess left on tyres to collect dirt or sand. Any excess left exposed to the air dries up and is blown away. Rim soap is packed in 20kg plastic containers with safety seal lids
FREYLUBE PREMA
Freylube Prema is a 100% synthetic lubricant specially formulated for heavy-duty vehicles and extreme temperature conditions. It is a single, ready to use multi purpose product for mounting, dismounting and protection against rust. Lubricates tyre beads for easier mounting. Exclusive formula contains no water; prevents rust and corrosion. Will not harden or evaporate, ensuring long shelf and service life. Keeps the tyre from fusing to the rim to provide easy dismounting and protection against damage to the bead and rim.
WWW.RIMTEC.COM.AU
Notes
Notes
WWW.RIMTEC.COM.AU
55
Notes
Notes
56
WWW.RIMTEC.COM.AU
Rimtec Australia
Western Australia (Perth)
Rimtec Pty Ltd Phone: (61) 08-9478 1333 Fax: (61) 08-9478 1355
Queensland (Brisbane)
Rimtec Pty Ltd Phone: (61) 07-3026 6383 Fax: (61) 07-3026 6388
Rimtec SA