You are on page 1of 13

Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

FEATURES DESCRIPTION
PC half-bridge (or 494) power supply supervisor +
SG6105 controller is designed for switching mode
two 431 + PWM
power supply for desktop PCs. It provides all the
High integration & few external components
functions necessary to monitor and control the output of
Over-voltage protection for 3.3V, 5V and 12V
the power supply. Remote ON/OFF control, power good
Under-voltage protection for 3.3V, 5V and 12V circuitry, some protection features against over-voltage
Under-voltage protection for –12V and/or –5V
and over-power are implemented. It directly senses all the
Over-power and short-circuit protection
output rails for OVP without the need of external dividers.
Power-down warning circuitry
An innovated AC-signal sampling circuitry provides a
Power good circuitry sufficient power-down warning signal for PG. A built-in
Delay time for PSON and PG signal
timer generates accuracy timing for control circuit
Remote ON/OFF function
including the PS-off delay. The cycle-by-cycle PWM
On-chip oscillator and error amplifier
switching prevents the power transformer from the
Two shunt regulator for 3.3V and 5V-Standby saturation and ensures the fastest response for the
Latching PWM for cycle-by-cycle switching
short-circuit protection which greatly reduce the stress for
Push-pull PWM operation and totem pole outputs
power transistors. Two internal precision TL431 shunt
Soft-start and maximum 93% duty cycle
regulators provide stable reference voltage and driver for
3.3V and 5V-standby regulation. Utilizing minimum
number of external components, the SG6105 includes all
APPLICATIONS
of the functions for push-pull and/or half-bridge topology,
Switching mode power supply for Computers, such decreasing the production cost and PCB space, and
as: increasing the MTBF for power supply.

ATX NLX SFX (micro-ATX)

MARKING DIAGRAMS PIN CONFIGURATION

20
PSON 1 20 VCC

19
SG6105T V33 2 RI

XXXXXXXYYWWV V5 3 18 SS

OPP 4 17 IN

1 5 16 COMP
UVAC

NVP 6 15 GND

V12 7 14 FB1
T: D = DIP
OP2 8 13 VREF1
XXXXXXX: Wafer Lot
YY: Year; WW: Week OP1 9 12 VREF2
V: Assembly Location PG 10 11 FB2

©System General Corp. -1- www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

ORDERING INFORMATION
Part Number Package
SG6105D 20-Pin DIP

PIN DESCRIPTIONS
Name Pin Type Function
VCC 20 Supply Supply voltage. 4.5V ~ 5.5V. It is connected to 5V-standby.
Power Good logic output, 0 or 1 (open-collector). PG = 1 means that the power is good for operation.
PG 10 Logic output
The PG delay is 300 msec.
V33 2 Analog input 3.3V over-voltage/under-voltage control sense input.
V5 3 Analog input 5V over-voltage/under-voltage control sense input.
V12 7 Analog input 12V over-voltage/under-voltage control sense input.
Over-power sense input. This pin is connected to driver transformer or the output of current
OPP 4 Analog input
transformer. When not in use, this pin should be grounded.
Remote On/Off logic input forʳCPU or controller. Turn on/off the PWM Output after the 7.5 msec / 26
msec delay.
PSON 1 Logic input
PSON = 0 means that the main SMPS is operational.
PSON =1 means that the main SMPS is off and the latch is reset.
NVP 6 Analog input The protection input for negative output, such as –12V and/or –5V. Trip voltage = 2.1V.
UVAC 5 Analog input AC fail detection, detect main AC voltage under-voltage and/or failure.
COMP 16 Analog output Error amplifier output and the input of the PWM comparator.
IN 17 Analog input The negative input of error amplifier. The positive input of error amplifier is a 2.5V reference voltage.
The soft-start. It is settable through external capacitor. The current source output at this pin is 8uA and
SS 18 Analog input
the voltage is clamped at 2.5V.
The totem-pole output drivers of push-pull PWM. The output are enabled (low) only when the NAND
OP1/OP2 9/8 Analog output
gate inputs are high, the maximum duty cycle on an output (OP1 or OP2) is 46%.
FB1 14 Analog output Output for first converter regulation loop.
VREF1 13 Analog input Reference comparison input for first converter regulation loop. 2.5V.
FB2 11 Analog output Output for second converter regulation loop.
VREF2 12 Analog input Reference comparison input for second converter regulation loop. 2.5V.
Program. Connected to external resistor for the reference setting.
RI 19
Analog input RI = 75k ohms.
GND 15 Supply Ground.

©System General Corp. -2- www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

BLOCK DIAGRAM

V33 V5 V12 UVAC RI PG GND VCC


2 3 7 5 19 10 15 20

DSD

UV 2uA Vref 14 FB1


Detector
_ COMP

0.7V + 13 VREF1

OV Delay
Protector 300msec

11 FB2
UV Delay
Protector 3sec 12 VREF2

5V 3.2V _ COMP

64uA
2.1V _ COMP
Delay Vcc 2.5V
7msec
NVP 6 Buffer +
D Q
_ 9 OP1
_ COMP
D Q 8uA CK _
2.4V Q
CK +
Delay COMP
OPP 4 Buffer +
7msec R
+
_
Error O.S.C
Vcc Delay
15msec Amp

_ COMP
8 OP2
1.4V On/Off Delay S Q
Delay
26msec 2msec
PSON 1 + 7.5msec R

18 17 16
SS IN COMP

©System General Corp. -3- www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

TIMING DIAGRAM

VCC

PSON

3.3V,5V,12V

tPSON(ON) tUVP
NVP
tPSON(OFF) tNVP

SS(on/off)
tPSOFF

PG
tPG

VCC

PSON

Voltage < VUVAC

UVAC

OPP
tOPP

SS(on/off)

PG

©System General Corp. -4- www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

ABSOLUTE MAXIMUM RATINGS


Symbol Parameter Value Unit
VCC DC Supply Voltage at Pin 20 16 V
VFB Shunt Regulator Output at Fb1, Fb2 Pins 16 V
IOUT Output Current at PG, Fb1, Fb2 Pins 30 mA
PD,25к Power Dissipation (TA=25 к) 1.5 W
PD,90к Power Dissipation (TA=90 к) 0.5 W
TSTG Storage Temperature Range -55 to +150 к
RθJA Thermal Resistance, Junction-To-Air 82.5 к/W
TJ,MAX Operating Junction Temperature 150 к
TA,MAX Operating Ambient Temperature -30 to +125 к
TL Lead Temperature (Soldering, 10sec) 260 к
ESD Capability, HBM model 3.0 kV

Note: All voltage values, except differential voltage, are with respect to network ground terminal.

RECOMMENDED OPERATING CONDITIONS


Symbol Parameter Value Unit
VCC DC Supply Voltage at Pin 20 4.5 to 5.5 V
VFB Shunt Regulator Output at Fb1, Fb2 Pins 4 to 16 V
TOPER Operating Ambient Temperature Range -25 to +85 к

ELECTRICAL CHARACTERISTICS (VCC = 5V, TA = 25°°C)


Symbol Parameter Test Condition Min. Typ. Max. Unit
ICC Total Supply Current PG High - 5 10 mA
VOVP1 Over-Voltage Protection 3.3V - 3.9 4.1 4.3 V
VOVP2 Over-Voltage Protection 5V - 5.8 6.1 6.5 V
VOVP3 Over-Voltage Protection 12V - 13.9 14.5 14.9 V
VUVP1 Under-Voltage Protection 3.3V - 2.0 2.6 2.8 V
VUVP2 Under-Voltage Protection 5V - 3.0 3.6 3.9 V
VUVP3 Under-Voltage Protection 12V - 6.0 7.2 8.0 V
VUVS1 Under-Voltage Sense 3.3V for PG Low - 2.5 2.8 3.0 V
VUVS2 Under-Voltage Sense 5V for PG Low - 4.0 4.3 4.5 V
VUVS3 Under-Voltage Sense 12V for PG Low - 9.4 10.1 10.4 V
VOPPS* 1 Over-Power Protection. VUVAC = 1.5V 2.02 2.4 2.66 V
VNVP Negative Voltage Protection: Voltage Level - 2.0 2.1 2.2 V
INVP Negative Voltage Protection: Source Current RI = 75kΩ 57 64 72 uA
tOVP Timing for Over-Voltage Protection RI = 75kΩ 0.37 0.7 1.35 ms
tUVP Timing for Under-Voltage Protection RI = 75kΩ 0.8 2.4 3.75 ms
tUVS Timing for Under-Voltage Sense for PG Low RI = 75kΩ 0.37 1.2 1.88 ms
tOPP Timing for Over-Power-Protection RI = 75kΩ 3.3 7 11.3 ms
tNVP Timing for Negative Voltage Protection RI = 75kΩ 3.3 7 10.2 ms

Note *1: VOPPS = (2/3) x VOPP + (1/3) x VUVAC ;

©System General Corp. -5- www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

Shunt Regulator (FB1, VREF1, FB2, VREF2)


Symbol Parameter Test Condition Min. Typ. Max. Unit
VREF Reference Voltage к
IFB = 0.5mA, TA = 25 2.475 2.5 2.525 V
VDEV, I *2 Deviation of VREF Over Load Current IFB = 0.5mA to 10mA - - 20 mV
VDEV, T * 2 Deviation of VREF Over Temperature TA = -25к to 85к - 10 30 mV
REGLI-FB*2 Line Regulation 4 < VFB < 16V - 1 - mV/V
IOUT-FB*2 Output Sinking Current Capability VFB > 2V 10 - - mA
Note *2: Not tested in production test.

Power Good Section


Symbol Parameter Test Condition Min. Typ. Max. Unit
tPG Timing for PG Delay RI = 75kΩ 200 300 400 ms
VUVAC UVAC Voltage Sense for PG - 0.65 0.7 0.75 V
tR*2 PG Good Output Rising Time CL = 100pF - 1 - us
tF*2 PG Good Falling Time CL = 100pF - 300 - ns
VOL2 Power Good Output Saturation Level IPG = 5mA - - 0.5 V
ION2 Power Good Leakage Current Collector VPG = 5V - - 1 uA

Remote On/Off
Symbol Parameter Test Condition Min. Typ. Max. Unit
VPSON PSON Input Threshold Level - 1 1.4 2.0 V
IPSON Remote Input Driving Current - - - 0.5 mA
Timing PSON to On/Off
tPSON(ON) On RI = 75kΩ 17 26 45 ms
tPSON(OFF) Off (PS-off) 5 7.5 28.8
tPSOFF Timing PG low to Power Off RI = 75kΩ 1.5 2 6.3 ms

Error Amplifier
Symbol Parameter Test Condition Min. Typ. Max. Unit
V2.5 Reference Voltage - 2.45 2.5 2.55 V
IIB*2 Input Bias Current - - - 0.1 uA
AVOL * 2 Open-Loop Voltage Gain - 50 60 - dB
BW * 2 Unity Gain Bandwidth - 0.3 1 - MHz
PSRR * 2 Power Supply Rejection Ratio - 50 - - dB

Oscillator Section
Symbol Parameter Test Condition Min. Typ. Max. Unit
FOSC PWM Frequency RI = 75kΩ 60 65 70 KHz

Soft-Start Section
Symbol Parameter Test Condition Min. Typ. Max. Unit
ISS Charge Current RI = 75kΩ 6 8 9.3 uA

©System General Corp. -6- www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

Comparator Section
Symbol Parameter Test Condition Min. Typ. Max. Unit
DC Duty Cycle - 85 - 93 %

PWM Output Section (OP1, OP2)


Symbol Parameter Test Condition Min. Typ. Max. Unit
VOL Output Voltage Low Io = 5mA - - 0.5 V
VOH Output Voltage High V12 = 12V 4 - - V
RO Output Impedance of VOH - 1.5 - 3.3 kΩ

©System General Corp. -7- www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

APPLICATION 1

-12V
MAIN +
Transformer

12V
+

5V
+

3.3V
+

UVAC V33

V5
3.3V
V12

VCC 5Vsb
VREF2
5Vsb
47~100ohm
STBY
PG Pok
Transformer FB2
1Kohm
VREF1 PSON PSon
+
NVP -12V
SG6105

FB1
OP1 -5V
RI

GND
5V

Vdd
IN 12V

COMP

OP2

OPP SS

©System General Corp. -8- www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

APPLICATION 2

OPP

R61
CN2

R62

3
2
1
C39

1
F2
OP1

1
C40

2
D26

2
C45 R63
1 3

2 1

1
R64
Q12
D27
L11 L12
5 6 7 8
D28
U4 2 1
RI NC FB GND

2
SG6848 R65

2
C42 D29 3 1
2 1
SEN NC VDD Gate T5

1
C78 4 3 2 1 D30 4 2
R66 R67
HHV 1 Q13 3
+

R68 R71
C44

2
2
R69
1

C48 OP2
1

D31 C46

2
D32 T6

C47
2

1 Q14
1

1
2

R70 6 9
3 2 D33 TR2

10
5

8
2

2
2
10
3

6
8

4
D34 D35 BD1

2
U5 T7
E16-D + +
2 3
C49 C50
1

1
4

R74 R75
2

1
D37 D38 R73 R77 R78

R76
C51 C52 C53 C54
1

R79 R80
+

+
FB1
C55 R81 R82
1

1
VREF1 R84 R85
R83
3 2 3 2
VZ3 VZ4
R86 C56 Q15 Q16
1 L13 2 1 2 1

2 D39 D40
C57 2 1 2 1
HHV
+

R87
C58
C59 R88

D41
7

5
5VSB T8

C60
11

10

12

13

14
8

UVAC
C69
V5 R89

R104 R103
1

U6
1 20 D45 D46 C61
PSON PSON VCC
R90
2 19
3.3V V33 RI
2

3 18 C62
5V V5 SS
-5V -12V R91
4 17
OPP OPP IN 5V
2

C63
R93 R94
D42 R92 5 16
UVAC UVAC COMP 12V C64
R95
R96
6 15
NVP GND
1

R97
1

1
1

7 14 L14 D43 D44


12V V12 FB1 FB1 R98 R99
3

3
1

3
1

8 13 VR3
OP2 OP2 VREF1 VREF1 C65 C66
2

2
2

9 12 Q17 Q18
OP1 OP1 VREF2 VREF2
2

R100
1

10 11
1

PG FB2 FB2
3
1

D48
SG6105 R101 R102

Q19
9

7
5
3

1
2

C67 C68
2

PG
D47 L15
1 2
10

8
6
4

C70
1

V5
+
1

R107 L16
FB2 L18 L17
C79 R112 Q20 3
1

2 C71
C73 C72
2

1
+
+

L19 -12V
2

2
+

+
1

+
C74 R113 R110 C75 R111
R115 L20
2

VREF2
+

C76
2
2

12V 5V
U7
+

VI

LM7905
R116
1
GND
R105 R106 R109
VO

3.3VSENCE C77
3

3.3V
+

-5V

©System General Corp. -9- www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

threshold level. PG pin goes high when the above


Example of Using SG6105 for the ATX
condition is reached. A 2K pull up resistor may connect to
Power Supply 5V.
Protection against over-voltage, short-circuit and The VCC can be supplied from the 5V-standby.
fault conditions is mandatory in PC power supplies. These When the VCC voltage is higher than 7V, besides the
protection circuits can be realized by using many discrete shunt regulator, the circuit of SG6105 will be
components and comparators, which occupy a lot of PCB shutdown and reset. No extra power supply is
space and also add to assembling costs. This single chip needed.
controller IC provides complete protection circuits, shunt Two internal high precision 431 shunt regulators are
regulators, and PWM control function and with less built-in. It provides stable reference voltages.
number of components. SG6105 is an ideal controller IC Complete PWM control circuitry including the error
for PC switching mode power supplies. amplifier for push-pull or half-bridge operation.

The features and benefits of this device are listed


below: Supervisory Circuit Operation
Over-voltage and under-voltage protection for 3.3V, The PC generates the remote ON/OFF logic (PSON),
5V and 12V without external divider which is “Low” for power supply “On” and “High” to
Over-power protection. switch off the power supply. The remote ON/OFF is
UV protection for –12V and/or –5V. connected to PSON input.
Power-down warning for power good signal.
Power good signal and power-fail lockup
Remote on/off control. APPLICATION GUIDES
Delay time for PSON and PS-off signal.
Two shunt regulator for 3.3V and 5V-Standby
Introduction
regulation. The application guide shows the key-feature of
Complete pulse width modulation (PWM) control SG6105 and illustrates how to use in an ATX switching
circuitry. mode power supply (SMPS). SG6105 is suitable for
On-chip oscillator. half-bridge, push-pull topology. It incorporates with a
Programmable Soft-Start. 4-channel supervisor, including 5V-standby. The PWM
Maximum 93% duty cycle section of SG6105 comprises a built-in 65kHz oscillator
Few external components and high immunity circuits, which protect the system
More reliable system from noise interference and provide more noise margins
Little space on PCB for improper PCB layout. SG6105 has OVP and UVP for
Easy trouble-shooting and implementation 12V, 5V and 3.3V. Besides, the NVP is used for negative
voltage protection, such as –12V and/or –5V. The UVAC
(AC fails detection) is applied to detect AC line condition.
FEATURE DESCRIPTIONS Two built-in internal precision TL431 shunt regulators
Over voltage protection can be implemented without
can be used for 3.3V or 5V auxiliary standby power.
any additional components. Over-voltage sense
Levels or 3.3V, 5V, 12V are 4.1V, 6.1V, 14.5V
respectively.
Over current and/or short circuit protection can also
AC Fails Detection
be achieved by using over-power protection, in Through a resistor divider, UVAC is connected to
which OPP pin is connected to the current the secondary power transformer for detecting the AC line
transformer (driver transformer). condition. Once the voltage of UVAC is lower than 0.7V
The power good signal is asserted to indicate the for a period of time, such as 200usec, the PG (power good)
3.3V, 5V and 12V is above the under voltage signal will be pulled low to indicate an AC line
power-down condition. The voltage amplitude of the

©System General Corp. - 10 - www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

PWM switching signal in the secondary power


transformer is proportional to the AC line voltage. Adjust
the ratio of resistor divider to decide the threshold of Negative Voltage Protection
power-down warning. A small capacitor is connected The NVP provides an UVP (under voltage protection)
from UVAC to ground for filtering the switching noise. for negative voltage outputs. An under-voltage represents
the phenomenal of the overload condition in negative
VS
Vo voltage output. For example, the –12V output may drop
to –10V during the overload situation. A resistor
Vin
determining the threshold of the protection is connected
from pin NVP to the negative voltage output. Via this
R1
resistor, NVP outputs a 64uA constant current to the
+ negative voltage output. When the NVP voltage is over
UVAC
R2 C1 0.7V 2.1V and the situation kept for longer than 7 msec, 6105
will lock the power outputs off.

VNVP = 64 uA × (R1 + R2) – V-12V


Over Power Protection (OPP) The power outputs will be locked off when VNVP ≥
The OPP (over power protection) is used for 2.1V.
detecting over power and/or short-circuit conditions.
When OPPS voltage (p.4, Note-1) is higher than 2.1V and
this situation existed for longer than 7 msec, 6105 will
pull the PG low and lock off the power outputs.
64uA

R1 R2
OP1
+ -12V

2.1V -5V

Vdd

OP2
R1 R2
OPP

C1 R3

©System General Corp. - 11 - www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

MECHANICAL DIMENSIONS
20 PINS – DIP (D)

Ӱ
D
20 11

E1 E eB

1 10

A2 A
L
e

b1
A1
b

Dimension

Symbol Millimeter Inch


Min. Typ. Max. Min. Typ. Max.
A 5.334 0.210
A1 0.381 0.015
A2 3.175 3.302 3.429 0.125 0.130 0.135
b 1.524 0.060
b1 0.457 0.018
D 24.892 26.162 26.924 0.980 1.030 1.060
E 7.620 0.300
E1 6.223 6.350 6.477 0.245 0.250 0.255
e 2.540 0.100
L 2.921 3.302 3.810 0.115 0.130 0.150
eB 8.509 9.017 9.525 0.335 0.355 0.375
θ˚ 0̓ 7̓ 15̓ 0̓ 7̓ 15̓

©System General Corp. - 12 - www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003
Product Specification

Power Supply Supervisor + Regulator + PWM SG6105

DISCLAIMERS

LIFE SUPPORT
System General’s products are not designed to be used as components in devices intended to support or sustain
human life. Use of System General’s products in components intended for surgical implant into the body, or other
applications in which failure of the System General’s products could create a situation where personal death or injury may
occur, is not authorized without the express written approval of System General’s Chief Executive Officer. System
General will not be held liable for any damages or claims resulting from the use of its products in medical applications.

MILITARY
System General's products are not designed for use in military applications. Use of System General’s products in
military applications is not authorized without the express written approval of System General’s Chief Executive Officer.
System General will not be held liable for any damages or claims resulting from the use of its products in military
applications.

RIGHT TO MAKE CHANGES


System General reserves the right to change this document and/or this product without notice. Customers are advised
to consult their System General sales representative before ordering.

©System General Corp. - 13 - www.sg.com.tw


Version 2.3(IRO33.0011.B0) June 19, 2003

You might also like