after wall has been finished/ tiled. HYDROTOWER-310 INSTALLATION INSTRUCTION AND WARRANTY IN WALL TANK , 3/6L K-4178IN-2-NA BEFORE YOU BEGIN Read the installation guide carefully and install the product according to instructions in the guide to avoid product damage. The product information contained in this publication is correct at the time of printing. Kohler Co. reserves the right to implement changes or product characteristics , packaging and availability at any time without notice. Do not use corrosive cleaners or solvents in or on the tank, as they may damage it. Do not use spares that are not provided by Kohler, and please do not use adhesive tape on threaded parts. Kohler will not be responsible for any damage related to installation with spares not provided by Kohler. ORDERING INFORMATION INWALL TANK ..................................................................................................K-4178IN-2-NA DROPLET FACEPLATE ..................................................................................K-4177IN-2-CP 3 1. Packing Layout. 2. Rough-in. All dimensions in mm. Fixture dimensions are nominal and conform to tolerances as per ASME Standard A112.19.2M. There are 2 hole locations for installation on the upper part of the tank (as shown). Install as required to conform with rough-in dimensions. 3. Recommended Tools (Not supplied). Installation Instructions : 4. Drill 4 holes in the wall of diameter 8 mm and depth 40 mm, as per the rough-in. Insert plastic anchors in holes. 5. Using metal screws & washers provided, fix the tank to the wall by the mounting brackets provided on its top part. (Note: Ensure that the tank is levelled with the help . of Spirit Level.) 6. Attach 2 fixing brackets at the bottom of the tank and fix to the wall with metal screws & washers provided. 7. Fix the mask on the tank as shown. (Refer mask label for details). 8. Assemble the trap on the bottom of the tank as shown. Cut the trap to the required length (If required). 9. Cover the trap outlet hole by protective cap. 10. Connect the water hose to the tank inlet. (Note: Inlet valve shall be shut off at this time, as supplied). Wall can now be finished and tiled. 11. If the wall is finished & tiled ,trim the mask to the finished wall using a sharp knife. If the finished wall is to be tiled, please ensure that the thickness of the tile is included before you cut the mask. 12. Fix the button position panel to the mask using 4 Plastic fixation screws supplied. (Trim the length of plastic fixation screws if required) 13. Screw the push bars into the screws provided in the flush bracket until the unthreaded end of the bar is aligned with the panel. Ensure that the push bar is secured through the holes at the rear of the flush bracket. Trim the length of push bar (If required). Lock the push bar against the screws with the help of small locks. (Note: Test the flush action to ensure it is moving smoothly. Adjust the push bars as required.) Open the Inlet valve & check for flushing by pushing the push bars. 14. Align the faceplate with the large button on the left hand side as shown. Now push the faceplate from the bottom & then from the top. Ensure the flush button operates smoothly. 15. Complete the installation and the in-wall tank is ready for use.
3 7 9 (4 8 0 ) 4 8 0 Plastic Anchor 5 Metal screw Washer 6 8 10 Water hose Mask 11 Knife Mask Installation Tank Mask Insert & Slide to the Right Side Press Trim Knife Mask Installation Tank Mask Insert & Slide to the Right Side Press Trim Knife Mask Installation Tank Mask Insert & Slide to the Right Side Press Trim Knife Mask Installation Tank Mask Insert & Slide to the Right Side Press Trim Recommended Tools 1 Button Position Panel Fixation screw 1 2 3 Slide the screw into the panel Push it upwards to snap with the panel. Turn Anti-Clockwise to lock. Fixation screw in locked condition Hacksaw Trap Remove these 2 sheets before installation CAUTION: Do not cut beyond the minimum length as specified on the part . Before Cutting After Cutting (Not Supplied) 12 18. 1169511 Button Position Panel WARRANTY Kohler plumbing products are warranted to be free of defects in material and workmanship for 10 years in residential application and 5 years for non-residential application from the date of purchase. Kohler India and its Authorized Service Franchisee will make unit repairs or replacements under this warranty within a reasonable period of time, as determined by Kohler India or its Authorized Service Franchisee performing the repair or replacement. Kohler is not responsible for labor charges, installation or other incidental or consequential costs. To obtain warranty service, contact Kohler India either through your Dealer, Plumbing Contractor or by calling number given below. This warranty does not cover problems arising from poor/insufficient water quality beyond the recommended limits, excessive water impurities/hardness beyond the norms of drinking water, excessive humidity or improper care and cleaning. This is Kohler Co.s exclusive written warranty. Contact us at: India Customer Service Center, Kohler India Corporation Pvt. Ltd., 6th Floor, Office Tower, Ambience Island, NH-8, Gurgaon, Haryana - 122001 (Customer Care:1800-103-2244, Monday-Saturday from 10:00AM to 06:00PM) www.KOHLER.co.in/contactus.ndi 1175329-IN01-A -2- 13 14 15 SERVICE PARTS 3. 1181143 Washer-Flush valve 6. 1169469 Filter Assembly 5. 1169466 Fill valve connection assembly 4. 1181142 Shut-off valve assembly 11. 1175347 Actuation_Lever_Right assy. 7. 1175344 Side fill valve assembly 8. 1169485 Locator_Fill valve 2. 1179663 Inlet connection assembly 9. 1169498 Flush actuator Bracket 17. 1169487 Flush valve assembly A2601 12. 1175327 Push Bar assembly 13. 1169510 Fixation screw-Plastic 10. 1175343 Actuation_Lever_Left assy. Push Bars Unthreaded End Locks Faceplate Panel Faceplate Full Flush Button Half Flush Button 14. 1169489 Link_Full Flush 15. 1169490 Link_Half Flush 16. 1169492 Catchboard 19. 1169509 Square Mask Knife Mask Installation Tank Mask Insert & Slide to the Right Side Press Trim 20. 1175342 Adjustable Trap Assembly 21. 1169504 Tank Outlet Pipe 22. 1169507 Gasket_Tank_Outlet 1. 1169521 Installation Bracket Assembly x 4 x 4 x 2 CAUTION: Ensure that push bars just touch the inside surface of faceplate buttons without pushing the buttons outside Panel Flush Bracket