AP polypropylene resin shall comply with rele%ant food substance re&ulation,,S -A &uidelines as specified in Code of -ederal.e&ulators / C-.0, Title 21, Chapter 11 section 122$1+2# and section 12)$'2 2 suitable for contact with foodstuff, pharmaceutical use and potable water$.
AP polypropylene resin shall comply with rele%ant food substance re&ulation,,S -A &uidelines as specified in Code of -ederal.e&ulators / C-.0, Title 21, Chapter 11 section 122$1+2# and section 12)$'2 2 suitable for contact with foodstuff, pharmaceutical use and potable water$.
AP polypropylene resin shall comply with rele%ant food substance re&ulation,,S -A &uidelines as specified in Code of -ederal.e&ulators / C-.0, Title 21, Chapter 11 section 122$1+2# and section 12)$'2 2 suitable for contact with foodstuff, pharmaceutical use and potable water$.
INDUSTRIAL ALPHAPLUS (AP) POLYPROPYLENE PIPING SYSTEM
1.0 PIPE 1.1 Material Pipe shall be extruded from Group 1, Class 2, Alpha nucleated homopolymer material in accordance with ASTM !"1#1$ AP polypropylene resin shall achie%e a minimum tensile stren&th of '## bar when tested at 2'C accordin& to ASTM (')$ Material shall allow continuous operatin& temperatures to *+ C$ AP resin shall comply with rele%ant food substance re&ulation, ,S -A &uidelines as specified in Code of -ederal .e&ulators /C-.0, Title 21, Chapter 11 Section 122$1+2# and Section 12)$'2*2 suitable for contact with foodstuff, pharmaceutical use and potable water$ 1.2 Stre Relie!e" Pipe shall be stress relie%ed by post!extrusion annealin& to eliminate inherent stresses in the pipe wall created durin& the extrusion process and eliminate weld failure due to pipe stress 1.# Pre$re Rati%& System /pipe and fittin&s0 shall be pressure rated in accordance with ASTM !2)'2 and in )#22 for hydrostatic desi&n basis$ Pipe shall be manufactured to an S. /standard dimension ratio0 in order to pro%ide the same pressure ratin& in all diameters$ Pipe shall be /select one01 S. 11 3 1+# PS4 /P51#0 S. 12$( 3 *# PS4 /P5(0 S. '' 3 "+ PS4 /P5'$20 P5 3 5ominal Pressure .atin& in 6ar 1.' Di(e%i)% a%" T)lera%*e Pipe shall be S. /standard dimension ratio0 series that defines the wall thic7ness and outer diameter of the pipe
2.0 FITTINGS 2.1 Material See material under P4P8 section 1$# 2.2 Pre$re Fitti%& All pressure pattern fittin&s /elbows, tees, flan&es and reducers0 from 9: /2# mm0 throu&h 1(; /"## mm0 shall be in<ection molded and shall ha%e the same pressure ratin& as the pipe$ 2.# Drai%a&e Patter% Fitti%& rain fittin&s /wyes, laterals, sanitary tees0 may be fabricated by miterin& and butt fusion weldin& or by side!wall fusion techni=ues$ 8xtrusion weldin& is permitted$ >ot air weldin& is not acceptable$ ?all thic7ness of fabricated fittin& shall be the same as the pipe$ 8/5/2014 1 SIMTECH GUIDE SPECIFICATION INDUSTRIAL ALPHAPLUS (AP) POLYPROPYLENE PIPING SYSTEM 2.' Di(e%i)% a%" T)lera%*e Soc7et fusion fittin&s dimension are in accordance with 4S@ 222* and 45 1(*(2$ 6utt fusion conform to S. /standard dimension ratio0 series that defines the wall thic7ness and outer diameter #.0 +OINING #.1 ,el"i%& Met-)" All pressure fittin& 9: /2# mm0 throu&h 2: /(' mm0 shall be soc7et fusion type <oints$ Pressure fittin&s, draina&e pattern fittin&s and pipe 29; /2+mm0 and lar&er shall be <oined by butt fusion weldin&$ All fusion!welded <oints to be performed in accordance with ASTM !2(+2 and pipin& manufacturers recommendations$ #.2 ,el"i%& Certi.i*ati)% a%" Trai%i%& Trainin& and certification shall be conducted by a direct Simtech employee$ 8ach welder will be fully trained on the weldin& e=uipment for the particular pro<ect and will be re=uired to demonstrate the full process of weldin&$ The process includes set up of the tool, loadin& of the pipe andAor fittin&s, ali&nment of the tool, and the weld process$ Trainin& will also include minor maintenance techni=ues to 7eep tools in ideal operatin& conditions$ After an operator has demonstrated their ability to operate the e=uipment, Simtech will issue a certified welders card upon completion$ '.0 MANUFACTURER S4MT8C> )22!222!2"(2 www$Simtech,SA$com 8/5/2014 2