Maxi Mount universal swivel bracket can be installed using one of the following optional hardware mounting packs: H 8045 Brick / Masonry Wall H 8046 Timber Frame Wall H 8047 Gypsum Stud wall mounting can be effected in two ways: Option1 (Mounting to the supports behind the plasterboard) Max. Load 8Kgs Drill a 10mm hole, install plugs into the plasterboard and screw the base into place using the 10G self tapping screws.
Maxi Mount universal swivel bracket can be installed using one of the following optional hardware mounting packs: H 8045 Brick / Masonry Wall H 8046 Timber Frame Wall H 8047 Gypsum Stud wall mounting can be effected in two ways: Option1 (Mounting to the supports behind the plasterboard) Max. Load 8Kgs Drill a 10mm hole, install plugs into the plasterboard and screw the base into place using the 10G self tapping screws.
Maxi Mount universal swivel bracket can be installed using one of the following optional hardware mounting packs: H 8045 Brick / Masonry Wall H 8046 Timber Frame Wall H 8047 Gypsum Stud wall mounting can be effected in two ways: Option1 (Mounting to the supports behind the plasterboard) Max. Load 8Kgs Drill a 10mm hole, install plugs into the plasterboard and screw the base into place using the 10G self tapping screws.
installed using one of the following optional hardware
mounting packs: H 8045 Brick / Masonry Wall H 8046 Timber Frame Wall H 8047 Gypsum Stud Wall Installation Separate the two sections of the bracket assembly by pressing the locking tab on the base and gently pushing the swivel ball assembly upwards. Use the base (section A ) as a template to mark the two screw hole locations on the wall. Note: Position the base so the two mounting screw holes are aligned vertically. Mount the base to the wall in one of the following ways taking into account the following: 1) Ensure the base is mounted the correct way up. (see Figure 1) 2) Ensure the two mounting screws do not protrude above the screw recesses where they will foul the slide-in ball assembly. H 8045 Brick / Masonry Wall Pack Contents: 8 x 8G Self Tapping Screws (To attach plate to speakers) 4 x 10G Grey Wall Plugs 4 x 10G Self Tapping Screws Drill an 8mm hole, install plugs into wall and screw the base into place using the 10G self tapping screws. H 8046 Timber Frame Wall Pack Contents: 8 x 8G Self Tapping Screws (To attach plate to speakers) 4 x 10G x 1.5" Self Tapping Screws Drill a 3.5mm hole and screw the base into place using the 10G self tapping screws. H 8047 Gypsum Stud Wall Pack Contents: 8 x 8G Self Tapping Screws (To attach plate to speakers) 4 x Toggle Nylon Fasteners 4 x 8G Self Drilling Screws 4 x 10G Self Tapping Screws Mounting can be effected in two ways: Option1 (Mounting to the supports behind the plasterboard) Timber Frame Drill a 3.5mm hole and screw the base into place using the 10G self tapping screws. Metal Frame Screw the base into place using the 8G self drilling screws. Option2 (Mounting directly to the plasterboard) Max. Load 8Kgs Drill a 10mm hole, install plugs into the plasterboard and screw the base into place using the 10G self tapping screws. Final Assembly Mount the swivel ball assembly with the mounting plate to the rear of the speaker and firmly tighten the lock nut. (see Figure 3) Adjust the angle of the ball to the desired position then evenly tighten the allen head socket screws with the allen key supplied. Carefully lift the speaker to the mounting bracket and locate the mounting posts into the key hole slots in the base. Slide the speaker with swivel ball assembly downward until it locks into position. If minor adjustment is required, partially loosen the 3 allen head screws and move the speaker to the angle required. Re-tighten the allen head screws. (see Figure 2) For security, insert a 8g x 3/4" self tapper screw into the hole provided. To remove speaker from the wall, remove security screw if fitted then press the locking tab and push the speaker upwards. Section A Section B TOP Security screw location Locking tab location Shaft Mounting plate Security screw location Allen head mounting bolts MAXI Installation Notes MAXI M O U N T Figure 1 Figure 3 Figure 2 111.1 74.4 Wall Mount Dimensions 74 106 86 54 Mounting Plate Dimensions