You are on page 1of 6

June 2010

17. Which of the following


transducer has the largest
linearity ?
(A) RTD
(B) Thermistor
(C) IC sensor
(D) Thermo couple
18. In negative feed back control
system,the output amplitude is
______ than in open loop control
system.
(A) always reduced
(B) always increased
(C) never reduced
(D) never increased
19. Which of the following physical
parameter can be measured by
LVDT ?

(A) Displacement
(B) Velocity
(C) Acceleration
(D) Pressure
20. The transfer function of a
control system is applicable to
which of the following ?
(A) Linear and time-invariant
systems
(B) Linear and time-variant systems
(C) Non-linear and time-variant
systems
(D) Non-linear and time-invariant
systems
30. Assertion (A) : The transient
performance of a feedback control
system is normally analysed by
using a unit-step function as the
reference input.

Reason (R) : Unit step function is


the most common input found in
practice.

33. Given below is a list of


transducers :
1. RTD
2. Thermocouple
3. IC sensor
4. Thermistor
The order in which the temperature
range sensed increases
(A) 1, 2, 3, 4
(B) 4, 1, 3,
2
(C) 2, 4, 3, 1
(D) 3, 4, 1,
2
35. For a closed loop system, the
roots of the characteristic equation
yields
1. Negative real repetitive roots in
critically damped case.
2. Positive roots in negatively
damped case and response
diverges out.
3. Real negative roots in over
damped case.
4. Sustained oscillations. Select the
correct sequence which takes the
system from stable to unstable
state, using the codes given
below :
(A) 1, 3, 4, 2
(B) 2, 4, 3,
1
(C) 3, 2, 4, 1
(D) 4, 1, 3,
2

Dec 2010

18. Which can measure pressure


directly ?
(A) Thermistor
(B) Bourdon tube
(C) LVDT
(D) Strain gauge
20. In feed-back control system,
overdamped condition for damping
ratio will be equal to
(A) one
(B) greater than one
(C) less than one
(D) zero

42. List I
List II
(a) Capacitive transducer(i)
Pressure
(b) Thermocouple
(ii) Strain
(c) Load cell
(iii)
Displacement
(d) Diaphragm
(iv) Temperature
Codes :
(a) (b) (c) (d)
(A) (ii) (iv) (iii) (i)
(B) (iii) (i) (ii) (iv)
(C) (ii) (i) (iii) (iv)
(D) (iii) (iv) (ii) (i)

june 2011
10. The resistance of thermistor is
a function of
(A) Current
(B) Temperature
(C) Heat
(D) Voltage
12. The transfer function of the
system
shown below is

(B) Seeback effect


(C) Capacitive effect
(D) Inductive effect
12. The transfer function of the
system show in the given figure is

37. List I
List II
(a) Resistive Transducer(i)
Diaphragm
(b) CapacitiveTransducer(ii) LDVT
(c) InductiveTransducer(iii)
Humidity
(d) PressureTransducer(iv)
Potentiometer
Codes are :
(a) (b) (c) (d)
(A) (iv) (iii) (ii) (i)
(B) (iii) (ii) (i) (iv)
(C) (ii) (i) (iii) (iv)
(D) (iii) (iv) (i) (ii)

dec 2011
11. When the force is applied on a
crystal the potential changes. This
is called
(A) Piezo electric transducer

18. The Hall effect experiment


provides
1. Hall co-efficient.
2. Type of the charge carrier.
3. Mobility of the charge carrier.
4. Temperature of the material
increases.
Of these statements,
(A) 1, 2, 4 are correct
(B) 1, 3, 4 are correct
(C) 1, 2, 3 are correct
(D) 2, 4, 3 are correct
40. List I
List II
(a) LVDT
(b) Bourdon gauge
Temperature

(i) Pressure
(ii)

(c) Strain gauge


Displacement
(d) Thermistor
Codes :
(a) (b) (c) (d)
(A) (iii) (i) (iv) (ii)
(B) (i) (ii) (iii) (iv)
(C) (ii) (i) (iv) (iii)
(D) (iv) (ii) (i) (iii)

(iii)
(iv) Stress

June 2012
18. The transducer which
generates electrical power
(A) Photoconductor
(B) Photodiode
(C) Solar cell
(D) Phototransistor
20. Which control system has
hysteresis property ?
(A) ON-OFF controller
(B) Proportional controller
(C) Integral controller
(D) P-I-D controller
21. Assertion (A) : If a
semiconductor is
placed in a transverse magnetic
field B and an electric field E is
applied across its other two
faces, then it would produce an
electric current I, in the direction
perpendicular to both B and E.
Reason (R) : Hall co-efficient is
proportional to the mobility of
charge carrier in semi-conductor.
41.
List I List II
(a) LVDT (i) Pressure
(b) Bourdon tube (ii) Temperature
(c) Strain gauge (iii) Displacement
(d) Thermistor (iv) Stress
Codes :
(a) (b) (c) (d)

(A) (iv) (iii) (ii) (i)


(B) (iii) (ii) (i) (iv)
(C) (iv) (i) (iii) (ii)
(D) (iii) (i) (iv) (ii)
28. The problem, with PI controller
is its
response to transients, is
(A) very fast
(B) having a dead zone
(C) non-linear
(D) sluggish
29. Which is the most linear
temperature
transducer ?
(A) Thermocouple (B) RTD
(C) IC-sensor (D) Thermistor
30. The variations in the ambient
temperature effect the following
parameters :
(A) Sensitivity (B) Accuracy
(C) Stability (D) Above all
50. Assertion (A) : Power is
integration of
energy over a period of time.
Reason (R) : The accuracy of
power
measurement is dependent on
integration time constant.

70. Match the following :


List-I List-II
(a) Small
displacement

(i) DSO
(b) Phase
measurement
(ii) X-ray
diffractometer
(c) Slowly
varying
signals
(iii) CRO
(d) Crystal
structure
(iv) LVDT
Codes :
(a) (b) (c) (d)
(A) (iv) (iii) (i) (ii)
(B) (iii) (ii) (iv) (i)
(C) (ii) (i) (iii) (iv)
(D) (i) (iv) (ii) (iii)

Dec 2012
19. The most suitable instrument
for the
measurement of voltage is
(A) DVM
(B) Analog voltmeter
(C) CRO
(D) DMM
20. The characteristic polynomial
of a
system is
The system is
(A) Stable
(B) Marginally stable
(C) Unstable
(D) Oscillatory

30. Assertion (A) : The sign of all


terms
in the first row of Rouths array
are checked, for stability
considerations.
Reason (R) : The number of sign
changes equals the no. of roots
on the right hand side of s-plane.
35. Following are the controllers :
1. On-off
2. PID
3. PI
The correct order of the decrease
in
error output is
(A) 1, 2, 3 (B) 1, 3, 2
(C) 3, 2, 1 (D) 3, 1, 2
45. List I List II
a. Strain
measurement
i. Pt-100
b. temperature
measurement
ii. load cell
c. Lissajous
figures
iii. bio-medical
signals
d. E.M.G. iv. C.R.O.
Codes :
abcd
(A) i ii iv iii
(B) ii i iv iii
(C) iii ii i iv
(D) iii iv ii i
28. A Resistance strain gauge has gauge
factor of 2. It is connected to a steel
member which is subjected to a strain
of 1 x10-6. If the original resistance
value of the gauge is 130 , what is the
change in resistance ?
(A) 130 (B) 390
(C) 260 (D) 520

29. What will be the output of K-type


thermocouple at 100 oC ?
(A) 40 V (B) 400 V
(C) 4000 V (D) 4 V
30. A system is said to be stable if and
only if
(A) All poles lie on the right half of
S. plane.
(B) All poles lie in the left half of the
S-plane.
(C) All poles and zeros lie on the
right half of S-planes.
(D) Some poles lie on the half of the
S-plane and some lie on the right
half of the S-plane.
40. During the process of milk boiling, the
heater is to be put off before the bubble
gets over spilled. The following controls
are put in operation while switching off
the heater. They are
I. Only proportional
II. Only integral
III. proportional and derivative
controls are followed.
IV. Only derivative
(A) I as well as II are followed.
(B) I as well as IV are followed.
(C) Only III is followed.
(D) I, II and IV are followed.
50. Assertion (A) : Due to two metal with
different coefficient of expansion,
when the junction is formed, the

junction produces a voltage


corresponding to temperature.
Reason (R) : The metals which are
used for making thermocouples are
non homogeneous.

60. The correct sequence to be followed to


build data acquisition system is by
arranging the steps as follows :
(i) transducer
(ii) software development
(iii) range of parameter
(iv) signal conditioning
(A) (i), (ii), (iii), (iv)
(B) (iv), (iii), (ii), (i)
(C) (iii), (i), (iv), (ii)
(D) (ii), (iii), (iv), (i)
70. Match the following :
List I List II
a. 3 digit 1. Guarding/shielding
b. Pt 100 2. Bridge
c. RTD 3. Temperature
d. Interference 4. DVM
Codes :
abcd
(A) 1 2 3 4
(B) 4 3 2 1
(C) 3 1 4 2
(D) 3 4 1 2

You might also like