Professional Documents
Culture Documents
Users manual
CODE: APT128A
TITLE: AUTV/100LD
REV: 0
DATE: 30/07/03
SS 96 Km 113
70027 Palo del Colle (Ba) ITALY
Tel. +39 (0)80 626755
Fax +39 (0)80 629262
E-mail: elettronika@elettronika.it
Web siste: http://www.elettronika.it
Index
Index ................................................................................................................................... 3
Warning .............................................................................................................................. 5
Warranty ............................................................................................................................. 6
Introduction ........................................................................................................................ 7
Content of the manual ....................................................................................................... 7
Treatment of electrical shock ........................................................................................... 9
First-aid ......................................................................................................................... 10
Treatment of electrical burns ........................................................................................ 10
Note............................................................................................................................... 10
Section 1 - Information .................................................................................................... 13
1.1 Description ............................................................................................................... 14
1.2 Technical characteristics .......................................................................................... 15
Block diagram................................................................................................................ 16
Section 2 - Installation ..................................................................................................... 17
2.1 Operating environement .......................................................................................... 18
2.2 Preliminary operations ............................................................................................. 18
2.3 Telemeasuring socket connections ......................................................................... 19
2.4 Control system ......................................................................................................... 19
2.5 Preventive maintenance .......................................................................................... 20
Front panel .................................................................................................................... 21
Rear panel ..................................................................................................................... 22
Section 3 - Diagram ......................................................................................................... 23
Cable diagram ............................................................................................................... 24
SCH0122BR1 (Control board and display) ................................................................... 25
SCH0128AR1 (Amplifier interface) ................................................................................ 31
SCH0192AR0 (200W LDMOS UHF Amplifier module) ................................................ 34
SP500-27/48 (Switching power supply) .......................................................................... 39
06604A (200W UHF TV Output Filter IMD Suppressor) ................................................ 41
WARNING
The apparatus described in this manual has been designed and manufactured with devices to safeguard the users. In any case it is recommended that during any operation of installation, maintenance,
miscellaneous interventions and calibrations requiring the apparatus to be switched on,
IMPORTANT
The component lists attached to the relevant electrical diagrams indicate for each item the reference,
the description and the type normally used.
The Elettronika S.r.l. though reserves the right to use or supply as spare parts components with
equivalent characteristics but of a different type, assuring anyway the optimal work of the apparatus
in accordance with the specifications.
The enclosed monographs are solely owned by Elettronika S.r.l.
The use of anything enclosed in this technical manual without explicit authorization given by Elettronika
S.r.l. will be prosecuted by the law.
The data and technical characteristics of the apparatus described in this manual are not compelling for
the manufacturer.
The Elettronika S.r.l. reserves the right to make, without previous notice, modifications or updates in
order to improve the quality of the product.
The general conditions of supply and sale are described in the contracts.
The delivery time are in accordance with the products and quantities ordered.
Warranty
Summary of warranty
We, ELETTRONIKA S.r.l., SS096 Km 113 Z.I. PALO DEL COLLE (BA) ITALY, warrant to the ORIGINAL PURCHASER of a NEW product, for a
period of one (1) year from the date of purchase by the original purchaser (the warranty period) that the new ELETTRONIKA product is free of defects
in materials and workmanship and will meet or exceed all advertised specifications for such a product. This warranty does not extend to any subsequent
purchaser or user, and automatically terminates upon sale or other disposition of our product.
What we will do
We will remedy any defect, in material or workmanship (except as excluded), in our sole discretion, by repair, replacement, or refund. If a refund is
elected, then you must make the defective or malfunctioning component available to us free and clear of all liens or other encumbrances. The refund will
be equal to the actual purchase price, not including interest, insurance, closing costs, and other finance charges less a reasonable depreciation on the
product from the date of original purchase. Warranty work can only be performed at our authorized service centers or at our factory. Expenses in
remedying the defect will be borne by ELETTRONIKA, including one-way surface freight shipping costs within the United States. (Purchaser must bear
the expense of shipping the product between any foreign country and the port of entry in the United States and all taxes, duties, and other customs fee(s)
for such foreign shipments).
Warranty alterations
No person has the authority to enlarge, or modify this warranty. The warranty is not extended by the lenght of time for which you are deprived of
the use of the product. Repairs and replacement parts are provided under the terms of this warranty shall carry only the unexpired portion of this
warranty.
Design changes
We reserve the right to change the design of any product from time to time without notice and with no obligation to make corresponding changes in
products previously manufactured.
INTRODUCTION
The apparatus described in this manual is the latest of this series, offering high performances, remarkable reliability and a wide range of characteristics, it all at a low cost.
Its is easy to install and use. It only takes to follow the installation procedure as shown in this manual:
after having removed all from the package, you only have to follow step by step the description in the
various sections.
Before starting to use the apparatus, remember to:
read carefully the general safety information contained in this section;
follow the instructions for the installation and set up of the apparatus;
read all the remaining sections of this manual in order to know well the apparatus and learn
how to obtain the best of its characteristics.
WARNING!
This manual is intended as a general guide for trained and qualified personnel who are aware of the
dangers inherent in handling potentially hazaedous electrical and electronic circuits.
It is not intended to contain a complete statement of all safety precautions which should be observed by
personnel in using this or other electronic equipment.
The installation, operation, maintenance and service of this equipment involves risks both to personnel
and equipment, and must be performed only by qualified personnel exercising due care.
Elettronika S.r.l. shall not be responsible for injury or damage resulting from improper procedures or
from the use of improperly trained or inexperienced personnel performing such tasks.
During installation and operation of this equipment, local building codes and fire protection standards
must be observed.
WARNING!
Do not remove, short-circuit or tamper with interlock switches on access covers, doors, enclosures,
gates, panels or shields.
Keep away from live circuits, know your equipment and dont take chances.
WARNING!
A - AIRWAY
B - BREATHING
C - CIRCULATION
2) If victim is responsive:
- keep them warm;
- keep them as quiet as possible;
- loosen their clothing (a reclining position is recommended).
FIRST-AID
Personnel engaged in the installation, operation, maintenance or servicing of this equipment are urged
to become familiar with first-aid theory and practices. The following information is not intended to be
a complete first-aid procedure, it is brief and is only to be used as a reference. It is the duty of all
personnel using the equipment to be prepared to give adequate Emergency First Aid and thereby prevent avoidable loss of life.
NOTE
If medical help will not be available within an hour and the victim is conscious and not vomiting, give
him a weak solution of salt and soda: 1 level teaspoonful of salt and 1/2 level teaspoonful of baking
soda to each quart of water (neither hot or cold).
Allow victim to sip slowly about 4 ounces (half a glass) over a period of 15 minutes.
Discontinue fluid if vomiting occurs (do not give alcohol).
2) Less severe burns - (1st & 2nd degree).
- Apply cool (not ice cold) compresses using the cleansed available cloth article;
- do not break blisters, remove tissue, remove adhered particles of clothing, or apply salve or ointment;
- apply clean dry dressing if necessary;
- treat victim for shock as required;
- arrange transportation to a hospital as qickly as possible;
- if arms or legs are affected keep them elevated.
10
AUTV/100LD
Users manual
11
12
_______________________________________________________________________________________________
Section 1 - Information
Contents:
1.1 Description
1.2 Technical characteristics
- Block Diagram
13
AUTV/100LD
LDMOS - UHF TV AMPLIFIER
1.1 DESCRIPTION
The amplifier AUTV/100LD is an apparatus designed to be used as final power stage or driver for higherpower amplifiers in the UHF TV band.
It is able to supply a power of 100W (peak sync.) in class AB and is completely realized with LDMOS
technology. The power supply of the apparatus is given by a switching power supply for the RF power
module and a traditional transformer for the control board. The protection board uses all the potential of a
microprocessor to check all the parameters of the amplifier module and the voltage of the power supply.
An output band-pass filter provides for the attenuation of the spurious products. The final result is a compact
apparatus, it is all inside a standard 19-3U cabinet, with a very good price-to-quality ratio.
14
470 - 860MHz
150W PEP
10/1
Solid State LDMOS
13dB
50W
50W
Better than < -54dB
N Female coaxial connector
N Female coaxial connector
Power supply
Power consumption
RS232 / RS485 Socket
Telemeasuring socket
Power factor
Ambient temperature
Relative humidity
Altitude
Cooling
Cabinet
Dimensions
Weight
FWD Power
REF Power
Temperature
IDC
VDC
130W
15W
70C
13A
Min 5V - Max 32V
GENERAL
PROTECTION THR.
15
Block Diagram
16
_______________________________________________________________________________________________
Section 2 - Installation
Contents:
2.1 Operating environment
2.2 Preliminary operations
2.3 Telemeasuring socket connections
2.4 Control system
2.5 Preventive maintenance
- Front panel
- Rear panel
17
2
WARNING!!!
FOR ELECTRICAL SAFETY REASONS AND IN ORDER TO KEEP THE APPARATUS SAFE,
THE GROUND TERMINAL OF THE APPARATUS MUST BE CONNECTED TO THE EXISTING GROUNDING SYSTEM AND NOT BY USING THE SHIELD OF THE OUTPUT
COAXIAL CABLE.
18
Before powering fully the apparatus, check that the output connections of the coaxial cable to the antenna
system are working.
In order to this it is possible to check the indication of the reflected power at low power levels. Only if
the SWR indication on the display is 0, the output power can be slowly increased. At maximum output
power, some watt might be shown as reflected power.
PIN N
SIGNAL TYPE
IN / OUT
Ground
DB9 Socket
Analog
FUNCTION
Output
Digital
Input
Digital
Output
Digital
Input
Analog
Output
Analog
Output
FWD Power
0 to 5V
Not used
Floating: Local
GND: Remote (Pin 3 Command accepted)
REF Power
0 to 5V
Temperature
0 to 5V
Not used
SW1
RS232
Open
Open
Open
Open
Closed
Closed
Closed
RS485
Closed
Closed
Closed
Closed
Open
Open
Open
PIN N
RS232
RX
TX
+5V
GND
+5V
RS485
RX-
RX+
+5V
GND
+5V
TX-
TX+
19
20
Front panel
LCD Display
RF Monitor connector
Function keys
Status LEDs
Main switch
DESCRIPTION
21
Rear panel
DESCRIPTION
Auxiliary socket
Breaker
Telemeasuring socket
RF Output connector
RF Input connector
2
22
_______________________________________________________________________________________________
Section 3 - Diagram
Contents:
- Cable diagram
- SCH0122BR1 (Display board)
- SCH0128AR1 (Amplifier interface)
- SCH0192AR0 (200W UHF LDMOS Amplifier Module)
- SP500-27/48 (Switching power supply)
- 06604A (200W UHF TV Output Filter IMD Suppressor)
23
24
SCH0122BR1
DESCRIPTION
The control board performs all the logic and control fucntions of the amplifier. Both the RF and power supply
parameters are continuously monitored in order to guarantee optimal performance in every working environment:
- amplifier supply voltages
- amplifier supply currents
- power module working temperature
- amplifier forward RF power
- amplifier reflected RF power
Vdc;
Idc;
Temperature;
FWD Power.
REF Power.
The board is based on a flash microcontroller working at a frequency of 20MHz, able to read the parameters,
control the amplifier and communicate with any PC connected through RS232/RS485 line. Besides, the
microcontroller is programmable, thus it is possible to change the internal program by connecting the appropriate
programmer to the J3 connector and this to a computer. The boards contains a 16 characters x 2 lines display
and two keys to change the parameter currently shown. There are also 3 different LEDs. The green LED
indicates when the amplifier module is ON, the red one is lit when an alarm in occur and the yellow one
indicates the remote control of the amplifier.
OPERATING CONTROL
As indicated in the previous section, the boards is able to read in real time all the necessary parameters to
control the amplifier. When the operator turns the amplifier on the display shows the software release number.
After a few seconds the amplifier is switched on and the first parameter shown on the display is the forward
RF power (FWD Power).
When a value read is out of the allowed boundaries, the microcontroller activates (after five scans to be
sure) the corresponding alarm indicating this on the first line of the display, and showing on the second line the
physical value. When the alarm is active, the microcontroller switches the amplifier off and restarts the time
counter (3 and 6 seconds). The microcontroller internally stores the number of occurred alarms and if it
reaches 5 the whole equipment is definitively switched off. In this case, if the operator needs to restart the
machine, it is necessary to switch it off and on again (locally o by remote). When the machine is working
normally on the first line shows TV AMPLIFIER UHF and the second line shows the parameter with the
format parameter = xx.x unit. The two keys on the frontal panel allow to change the currently shown
parameter: the left one goes to the next parameter and the right one goes back (in sequence Vdc, Vac,
Temperature, Idc, FWD, REF). If the amplifier is switched off, the STAND BY indication is shown on the
display and the backlight is turned off.
The amplifier can be remotely controlled by serial line (contact ELETTRONIKA for details). It is
configurable as RS232 or RS485.
25
26
27
28
Description
Qty.
Comps.
Page 1/2
CC 100nF-S 01065C
23
CC 15pF-S 01088
CC 1nF-S 01096
CC 1uF100V-S 01760A
CC 2nF2 2kV 01045A
CE 100uF25V-S 01793B
CE 10uF35V-S 01778A
CE 2200uF25V 01813
CE 22uF16V-S
D 1N4148-S 03002
DB KBL04 03042
DIS DMC16230 03072B
DL LEDG5 03060
DL LEDR5 03061
DL LEDY5 03054B
FUSE 1A MICRO FUSE
IC 78M05 04301B
IC 78M12 4307B
IC 79M08 04304A
IC INA168
IC LM393-S 04639
IC LMV324M-S 04658B
IC MAX232-S 04804B
IC MAX3080-S 04770
IC MC14094BD 04718
IC PIC16F877 4869
IC TC7662BCOA 04758A
IC ULN2003A 4870
IND 2u2H-S 05020A
J CON HD515V/05-4PVE
J FC-10P 02697-02699
J FC-16P 02701-02700
J PAN2 02739-40-41
J PAN8 02716-17-18
JU JUMP3 02707-02742
MOV 275V
R 100K-1%-S 00065B
R 10K-1%-S 00053B
2
5
8
3
2
4
1
2
7
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
2
2
1
1
1
1
1
2
12
R 120R-S 00030A
29
Part Name/Number
Description
Qty.
Comps.
R 1K0-1%-S 00041B
R 1K2-1%-S 00042A
R 22K-1%-S 00057B
R 2R2-S
R 3K9-1%-S 00048B
R 470K-S 00073A
R 470R-1%-S 00037B
R 47K-1%-S 00061B
R 4K7-1%-S 00049B
R 68K-1%-S 00063B
R 8K2-1%-S 00052B
RL 40.31.12 07567
RV 10K-3266X 00807
SW SWITCH-8DIP
SW VSS 0033.4604
T 06086 N 7630 7632
TR BC848 03457
TR BC856 03455
TRASF TRASF 14V5 7VA
XTAL 20MHz-S
3
2
1
1
3
1
3
3
4
1
3
2
1
1
2
1
2
1
1
30
Page 2/2
AMPLIFIER INTERFACE
SCH0128AR1
DESCRIPTION
The interface board (SCH0128AR1) is used to connect the amplifier stages to the control board
(SCH0122BR0) to allow to the microcontroller the reading of the RF and analogical parameters.
It is simply composed of one temperature sensor, a voltage regulator, some passive componentes and a
10 pin connector J2. This connector has to be connected to the corresponding one of the SCH0122BR0
board.
The LM317HV (IC1) integrated circuit is an adjustable 3-terminal positive voltage regulator used to
make more stable the power supply voltage of the amplifiers fan.
The LM35DT (IC2) integrated circuit is a precision temperature sensor whose output voltage is
proportional to the Celsius (Centigrade) temperature. It does not require any external calibration or
trimming. The package is a plastic TO-220 model and the heat sink is directly connected to the amplifier.
31
32
Description
Qty.
Comps.
CC 100nFAVX 01065A
D 1N4007 03009
IC LM317HV
IC LM35DT 00664
J FC-16P 02701-02700
J SCREWCONN2 02853
JU JUMP2 02739-02742
R 0R02
4
2
1
1
1
1
2
2
R 220R 0033
R 270R 0034
R 4K7 0049
R R400m NOT MOUNTED
1
1
1
2
C1-4
D1-2
IC1
IC2
J2
J1
JP1-2
R1
R7
R3
R2
R4
R5-6
33
SCH0192AR0
DESCRIPTION
The RF module is an integrated TV linear amplifier designed for UHF band, this module employs push-pull
LDMOS technology in order to achieve very good efficiency, high linearity and reliability.
LDMOS transistors operate in AB class. It is a wideband amplifier over the full frequency, no adjustment is
required for the channel change. The board includes RF section amplifier, bias circuit, protection circuit and
matching networks. A silver plated copper plate is brazed with PCB in order to obtain low thermal resistance.
Providing a minimum of 200W Pk sync linear power, this module is the perfect amplifier for any broadband
UHF power transmitter.
TECHNICAL CHARACTERISTICS
Output power
Input power
Frequency
Gain
LDMOS Power supply
LDMOS Bias current @+32V Vdc
RF Input impedance
RF Output impedance
Input / Output return loss
Drain efficiency
Storage temperature range
Dimensions (LxWxH)
34
300W max
15W max
470 - 860MHz
> 13dB
32V 2%
2A
50W
50W
> = 15dB
47% @ 250W
-50 to +150C
165x95x29mm
CALIBRATION PROCEDURE
- Technical characteristics
Power supply voltage
Polarisation current
Gain for low signal
32V ( 2%)
1.0 cold for each device (2A total), 0.1A
Not less than 13dB in the 470-860MHz band ( 1dB)
Compare to the typical curve eclosed
- Adjustment procedure
Polarisation current calibration
Gain curve
35
- Calibration steps
STEP 1. Close the input and the output of the module by connecting them to a 50W
W dummy load
and connect the spectrum analyser through a directive sample, in order to look for self-oscillation of the
module, if any (anyway the module has been designed so that it would not self-oscillate even if totally decoupled, without any input or output load).
STEP 2. Check the voltages of the polarisation circuits without assembling the transistors first:
connect the 32V power supply to the proper turret by means of a fastening screw, then give power and check
data:
- the stabilised voltage on the zener diodes DZ1 and DZ2 is about 15V compared to the ground;
- the stabilised voltage on the zener diodes DZ3 and DZ4 is about 6.8V compared to the ground;
- the voltage on the pads to which the gates of the LDMOS transistors will be soldered (R23 and R24
resistors side) changes from 0V to a maximum value of about 6V when moving the relevant trimmer (R7-R8).
STEP 3.
Check the work of the protections.
- Set both trimmers so that there is a value of about 4.5V on the pads of the gates;
- solder some wire to the pad between the two LEDs, next to the serigraphy of the input hybrid H1;
Solder a wire
- in order to check the work of the protections aboard, a power of about 4V has to be supplied to the wire,
for example by touching with it the reophore of C23 or C24 which is not connected to ground; the two red
LEDs will immediately light up and the two RF transistors will be switched off at the same time: the polarisation
current (2A) will decrease to 0 and of course the gain curve displayed by the spectrum analyser will decrease;
- after this it is important to restore the position of the two trimmers for the minimum voltage! Then
disconnect the 32V power supply.
STEP 4. Fastening of the LDMOS transistors: after properly cleaning the plate surface, smear a thin
layer of silicone fat on the lower side of the flange of the MOSFETs, fasten them to the heat sink and solder
the gate first, then the drain. Solder the two 13pF (ATC) chip capacitors and above them the two 1-5pF
36
capacitive trimmers, between the two pair of gates, as shown by the mounting plan.
STEP 5.
Connect serially a c.c. amperometer to the power supply, with scale starting from more than 5A
(i.e. 10A).
STEP 6. Power the module and check the MOSFET is not absorbing current; this means that the device
is integral and working correctly.
STEP 7. Slowly turn the R7 trimmer until the MOSFET absorbs 1A, always checking that there are no
self-oscillation; under this conditions it is possible to check by means of a digital tester that the voltage on the
gate is about 5.2-5.4V.
STEP 8. Repeat the previous step for the other section of the module, this time turnign R8 and checking
that the indication of the current on the amperometer increases to 2A total (which includes the current of the
other device left on).
STEP 9.
Check the response curve of the module by means of the network analyser.
STEP 10. Check the response curve for low signal with centre 660MHz and span 500MHz, 2dB/div.
STEP 11. The curve should be similar to the one enclosed, with a tolerance of 0.5dB. To obtain this, act
on the four trimmers C41-C41a and C42-C42a with the proper calibrator, inorder to flatten the curve as
much as possible, especially at the edged of the band which represents the minimum values.
STEP 12. Finally, check that the current in stand-by does not increase by more than 1520%, reaching at
worst 2.32.4A when the heat sink is hot and not ventilated.
Note: when mounting-removing the PALLET on the heat sink, tightly fasten the screw of each all N input and output
connectors. These are mounted with a single 3mm screw and if it is not properly fastened it may be detached from the PCB
by a movement of the connector once it has already been soldered to the path.
37
38
39
DESCRIPTION
ELETTRONIKA CODE
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R15
R16
R17
R18
R19
R20
R21
R22
R23
R24
*R25
*R26
C1
C2
C3
C4
C5
C6
C7
C8 x 2
C9 x 2
C10 x 4
C11 x 4
C12
C13
C14
C15
C16
C17
00045A
00045A
00045A
00045A
00042A
00042A
00800
00800
00042A
00042A
00056B
00056B
00075A
00001
00416A
00432
00049A
00049A
00012A
00012A
00012A
00012A
00396
00396
40
01807B
01807B
01807B
01795
01795
01145
01145
01065H
01065H
01135
01135
1065G
1065G
1065G
01613A
01613A
1065G
Page 1/3
REF.
DESCRIPTION
ELETTRONIKA CODE
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
C33
C34
C35
C36
C37
C38
C39
C40
C41 x 2
C42 x 2
C43
C44
C45
C46
C47
C48
C49
C50
C51
C52
C53
C54
C55
C56
C57
C58
C59
T1
T2
B1
1065G
01626A
01626A
1065G
1065G
1065G
1065G
01145
01145
01145
01145
01123
01123
01123
01123
01104
01104
01143
01143
01143
01143
01108
01108
1485
1485
01104B
01104B
01111
01111
01111
01111
01119A
01119A
01113
01113
01113
01113
01117
01117
01108
01108
01160
04034
04034
08491
Page 2/3
41
REF.
DESCRIPTION
ELETTRONIKA CODE
B2
B3
B4
L1
L2
L3
L4
H1
H2
NTC1
NTC2
IC1
IC2
DZ1
DZ2
DZ3
DZ4
DL1
DL2
PN964AR3
08491
08492
08492
07684
07684
42
05368
05369
00661
00661
04583
04583
03135
03135
03137
03137
03056
03056
0643K
V0774
09983
Page 3/3
E0013
SPECIFICATION
MODEL
DC Output Voltage
Output Rated Current
Output Current Range
Ripple & Noise (p-p)
DC Output Power
Efficiency
DC Voltage Adj.
Over V. Protection
Input Voltage Range
Input Frequency
Power Factor
Overload Protection
27Vdc
18A
0-18A
200mVp-p
486W
87%
24-30V
31V-36.5V
88-264Vac
47-63Hz
0.95/100-240Vac
105%-135%
Type: Foldback current limiting
Recovery: Auto
> =70C Output Shutdown
Temp. > =60C Fan On
< =50C Fan Off
-10C/+50C, 20%-90% RH
185x120x93
1.8Kg.
48Vdc
10A
0-10A
240mVp-p
480W
87%
41-56V
57.6V-67.2V
43
44
45
1K
MOC3022
R 71
5K1
C53
U53:B
PC1 2 3
22 /1W
27 /1W
39 /1W
471
/1 KV
331
/1 KV
221
/1 KV
24 V
27 V
48V
D 92 02
D 92 02
D 92 02
TR 132
TR 131
TR 130
TR 129
15 /1W
222
/50 0V
15 V
D 92 02
222
/50 0V
13.5 V
L5 1
222
/50 0V
12 V
M ODEL
R73
R 72
330
C57
103/50V
104/100V
U51:2
D54
1N4148
U 52:B
PC 123
R69
R 49
JU M P
D53
C56
1N4148
1u/50V
1M
103/50V
C N2
C
22 0 u
/63 V
47 0 u
/50 V
1K
/2W
3 K3
/2W
1 00 0u
/35 V
V-
6K 8
/1/2W
2K 2
2K 2
1K
1K
1 00 0u
/35 V
1 00 0u
/35 V
1K
R 86
U55
3 84 5
1 00 0u
/35 V
C 73 ,74
75
C 65
68P/50V
680
/2W
2 70
/2W
2 20
/2W
2 20
/2W
R 68
C 58
R8 2,83
C54
102/50V
C55
C60
104/100V
R51
200K/1W
R52
200K/1W
36K
24K
20K
10K
10K
6K 8
R 94
C61
471/100V
1K5
2K
2K
1K5
1K8
1K5
R9 5
1 5 /1 /2W
R 54
V-
C64
104/630V
R 57
6 80
R 66
1K
C 80
8 20
9 10
2 24
/1 00V
9 10
1 K2
1 K2
9 10
R 87
T+
T-
C51
100P/2KV
R 55
5.1
Q53
2 SC 26 55
R6 1
1R
2 24
/1 00V
1u /50 V
1u /50 V
1u /50 V
1u /50 V
Q5 4
A10 20
C62
CN2
B
R70
22 K
R67
24K
C 59
471/1KV
D52
1N4148
100u/35V
R6 0
15 /1/2 W
TF 404
TF 403
TF 402
TF 401
TF 400
C 101
Z D52
18V /1 W
J1,J2
J3
33V /1W
15V /1 W
J1,J2
J3
J2,J3
18V /1W
16.1 V
1 0 -1 2
13-15
C102
18
16
17
HE R204
D 69
C 87
22 2/5 00V
27V/1W
15V/1W
12 .9V
JUM P
J UMP
J UMP
Z D 53
222/250VA C
J1 ,J2
J3 ,J 4
J1 ,J 2
J3 ,J 4
J1,J2
J3,J4
1 .40
10mm
12.9 V
D 55
HE R10 4
C6 3
22 2/5 00 V
Q52
2 SK 13 5 8
R 59
5.1
2 22 /25 0VAC
TF 407
T 51
G
Q5 1
2S K13 58
D51
HER308
8
BD
R115
51
C52
103/2KV
BD
Z D 54
33V/1 W
18V/1 W
12V/1 W
JU MP
JU MP
JU MP
D 60 :A
D 62 :A
D 61 :A
1 6.1V
1 0.6 V
1 0.6 V
5 .4 V
5 .4 V
5 .4 V
Z D6 0
D 76
H ER 10 4
R G51
7 812
L5 2
D R0 05
R11 2
2 2/1 /2 W
D7 0
JUM P
78
82 0
1K 1
1K 2
1K 5
1K 8
1K 8
R8 4
R 50
1 0K
6 K8
1 0K
8 K2
6 K8
1 0K
1K
10
L51:A
R8 8
U 54 :C
L M 3 24
C7 9
10 4/1 00 V
47u/50V
R 53
100/2W
ZD51
R56
100
R74
75K
R65
68K
R 64
0.82/2W
R58
5K1
R62
18V/1W
R63
0.22/2W
C72
D60:B
BD
D61:B
BD
C 85
R 80
RC
C92
R 83
Q 56
2S C 1815
R 82
2 .2/1 /2W
R1 09
2 21/1 KV
ZD 55
5.1V/1W
0.22/2W
D62:B
560/1/2W
Q5 5
C 21 20
C74
J1
R1 07
1K
D6 8
1N 4148
J3
J4
J2
SH R1
C 80
U54 :B
LM 324
7
D 67
1N 4148
11
C9 1
2.2u/50V
T L4 31
U 54:A
LM 324
1
R8 6
-
R 10 8
15 K
R 92
1K
ZD60
LED1
R81
C86
R117
R84
2K
R 50
C73
SVR 2
JUMP
D64
1N4148
R91
22
C 93
105/50V
C7 5
R87
ZD54
R90
C
ZD52
ZD 53
C90
U51:1
MOC3022
1K
U 52:A
PC123
R
R 89
68K
5K1
R110
U53:A
PC123
D 75
H ER 204
C 92
C 71
1u/50V
R 120
C88
51/2W
C84
47u/50V
R11 6
103/50V
R111
2K
R106
100
CN 51:A
FAN
C83
47u/50V
A
C82
103/50V
D63
HER203
R100
3K9
R93
10
R 94
R95
SVR1
1K
R 96
10
TB1:F
-S
TB1:H
TB1 :A
+S
D 65
1N 41 48
D 66
1N 41 4 8
+V
TB1:B
-V
C77
473/630V
R-
R+
C78
473/630V
820
T5 1:D
R 103
6K8
C 76
104/100V
R101
3K9
R102
1.5 K
CN 4:A
RT
R104
RTH2
5K
820
RC-
R105
V+
C81
104/100V
46
QUANTITY
CASE 910-D-R3
CASE 910-T-R3
1208PTB1;L;20cm+TUBE/TYPE:B;
PIN KS-1
MYLAR FILM 910-R1
BOX PS-300 194x127x103mm
SCREW P 3x6
ISO NI
SCREW F 5.0x12 TP1 NI
SCREW F 3x6 TP2 NI
LABEL UP SP-500-27-R2
LABEL INDCON UL E010-R2 FAN CONT.
CARTON PS-300 1CUFT
261x18mm
327x18mm
BOM FOR SP-500-27A ON PCB
R/C 1/4W 5.1W 5% HP=10 T-52mm
R/C 1/4W 100W 5% HP=10 T-52mm
R/C 1/4W 680W 5% HP=10 T-52mm
R/C 1/4W 1kW 5% HP=10 T-52mm
R/C 1/4W 2.2kW 5% HP=10 T-52mm
R/C 1/4W 5.1kW 5% HP=10 T-52mm
R/C 1/4W 10kW 5% HP=10 T-52mm
R/C 1/4W 270kW 5% HP=10 T-52mm
R/C 1/4W 330kW 5% HP=10 T-52mm
R/C 1/2W 5.1W 5% T-52mm
R/C 1/2W 680kW 5% T-52mm
R/MO 2W 51W 5%
R/MO 2W 30kW 5%
R/M 1/4W 22kW 1% T-52mm
R/M 1W 499kW 1% MFR-1WS
R/NW 2W 0.22W 5%
R/NW 2W 0.33W 5%
R/FS 5W 10W 10% T=130C
NTC 5kW 10% TSC-502
MOV 0.6W 470V 14 TNR15G471K
C/Y2 221/250VAC 20% P=7.5 AC
C/Y2 222/250VAC 20% P=7.5 AC
C/Y2 472/250VAC 20% P=7.5 AC
C/X2 104/250VAC 20% P=15 KNB153X
C/X2 474/250VAC 20% P=22 KNB153X
C/M 104/63V 10% P=5
C/M 104/100V 10% P=5
C/M 474/50V 10% P=5
1
1
1
3
2
1
4
2
5
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
1
2
1
4
1
2
1
1
1
1
3
1
1
4
1
1
1
POSITION
1
CASE
+S+V -S-V G-RC
1
PCBA PCBB
FAN
CASE
8
1 TB1
TB2
R10, R11
R26, R32
R27
R24
R23, R25
R12
R16
R29
R30
R21
R1
R4
R17, R18
R28
R14, R15, R8,R9
R6
R5, R7
R2
RT
ZNR1
C32
C14, C3, C4
C16
C5
C1, C2, C17, C8
C21
C6
C18
47
SPECIFICATIONS
QUANTITY
POSITION
1
1
1
1
1
1
3
3
1
1
1
1
1
4
1
1
1
1
1
1
1
1
2
1
1
1
2
5
1
1
2
1
2
1
1
2
2
1
1
1
1
2
1
1
C20
C12
C11
C13
C67
C19
C10, C26, C9
C22, C24, C25
C17
C23
BD1
D2
D9
D4, D6, D7, D8
D1
D5
D3
ZD4
Q3
Q8
Q7
Q4
Q1, Q2
TRC1
U1
L1
LF1, LF2
C14F, D1A, Q1D,
Q1G, Q2D
Q2G
FS1
FS1
TB1
CN2, CN3
CN4
CN1
F-F
HS1, HS3
HS2
RT
RT
RT
L1
PCB
RT
48
SPECIFICATIONS
QUANTITY
POSITION
2
3
6
1
20/100
1
1
2
2
1
1
2
1
1
3
5
D1, TRC1
BD1, Q1, Q2
HS1, HS2, HS3
RT
RT
1
1
1
3
1
2
3
2
1
1
1
2
1
1
1
2
1
1
2
2
1
1
2
1
2
1
1
1
R61
R55, R59
R93, R96
R91
R115
R106, R56
R72
R57
R104, R105, R87
R107, R66, R73,
R88, R90
R92
R84
R102
R111, R116, R95
R86
R100, R101
R117, R58, R71
R103, R50
R108
R70
R94
R65, R89
R74
R69
R109
R54, R60
R112
R120
R80, R81
R51, R52
R110
R53
R82, R83
R67
R62, R63
R64
SVR1
RTH2
49
SPECIFICATIONS
QUANTITY
POSITION
1
2
3
2
2
5
1
1
1
2
1
1
2
1
1
3
1
1
1
2
1
3
1
3
3
2
1
2
1
5
3
1
1
1
3
1
1
1
1
1
2
1
SVR2
D70, R49
J1, J2, J3
C101, C102
C77, C78
C53, C60, C76,
C79, C81
C64
C80
C65
C71, C72
C61
C59
C63, C87
C88
C55
C54, C57, C82
C93
C51
C52
C56, C85
C91
C83, C84, C86
C62
C73, C74, C75
D60, D61, D62
D55, D76
D63
D69, D75
D51
D52, D53, D54,
D64, D65
D66, D67, D68
ZD60
ZD55
ZD53
ZD51, ZD52,
ZD54
LED1
Q54
Q56
Q55
Q53
Q51, Q52
SHR1
50
SPECIFICATIONS
QUANTITY
POSITION
1
1
2
1
1
1
1
1
10
TB DT-4C-B14W(1172)-08
WAFER 8822-02 P=2.5
I/O WIRE PSP300-CN1-R1
I/O WIRE PSP300-CN6-R2
I/O WIRE SP500-CN1-R1
I/O WIRE SP500-CN2-R3
HS YS021W-3 72020-3 h=25m/m
HS YS032W-070 71431W-070
CORE MS-130125 HKH-130
PCB SP-500B-R10 FR4 20Z DS
TW 30. NI
SCREW P 3x10 ISO NI
1
1
1
1
1
1
1
2
2
1
1
5
RG51
U51
U52, U53
U55
U54
L52
L51
T51
D60, D61, D62,
Q51, Q52
TB1
CN51
CN1
CN3
CN2
CN4
HS53
HS51, HS52
L51
PCB
RTH2
D60, D61, D62,
Q51, Q52
HS51, HS52,
RTH2
HS53
51
06604A
3 SECTION BANDPASS FILTER WITH 2 NOTCH ELEMENTS - COMB-LINE STRUCTURE, INDUCTIVE COUPLING
IRISES; CONSTANT BANDWIDTH, VERY EASY TO TUNE - EXACT GENERALIZED CHEBISHEV DESIGN
GIVING MAXIMUM SELECTIVITY AND MINIMUM GROUP DELAY VARIATION.
SPECIFICATIONS
Frequency
Connectors
Power handling
Insertion loss
Return loss
Operating temperature
Bandwidth
Selectivity @V.C.-5.5/+11
Selectivity @V.C.-11/+16.5
Weight
52
470 - 860MHz
N
200W CW
0.55dB Typ. @ V.C.
26dB
-10 to +50C
8MHz
-30dB
-22dB
1.2kg
TECHNICAL DESCRIPTION
The output filter 200W UHF is made up of a resonators bandpass filter and two notches. It can be
regulated on all the channels of UHF TV band (470 - 8690MHz) and according to all world-wide
standards (intercarrier 4.5 - 6.5MHz). The bandpass section is composed by the three middle resonators,
while the two resonators apart are the notches. The filter is symmetrical, therefore the choice of lowest
and highest notch is indifferent.
The bandwidth and the notch depth are predetermined, so they dont need any regulation.
The input/output coupling are regulated by means of the two screws which are in position opposed to
every connector. The regulation is carried out with a screwdriver, considering that when the screw
lines are parallel to the longer side of the filter the coupling is maximum, otherwise if orthogonal it is
minimum. The twist friction of the couplings can be set acting on the hexagonal clamps with a no. 12
key.
TUNING INSTRUCTIONS
The advised sequence is the following:
1. Set the instrument state as follows:
- C.F. = (V.C. + S.C.) / 2
- SPAN = INTERCARRIER * 5
(E.G. 27,5MHz std. B/G)
- TRANSMISSION SCALE = 5dB/div.
- REFLECTION SCALE = 5dB/div.
2. Turn the bandpass section on the required channel, and match input and output until a correct response
is achieved. During this step keep the tunings of the two notches well far away from the response. Fit the
curve at the center of the screen, so as to get the same attenuation at the borders. The input/output
couplings can influence the external resonators, therefore it will be necessary to repeatedly fix the
former after the latter in small steps.
3. Tune the two notches to P.V.-INTERCARRIER and P.A.+INTERCARRIER frequencies. This will
vary the response and matchning.
4. Adjust the bandpass external tunings. The lower notch side tuning shall be a little unscrewed, whereas
the upper notch side tuning will have to screwed.
5. Enhance a little the lower notch side coupling (the coupling screw toward the filter lenghth). Improve
53
the calibration alternatively acting on two sides according to this sequence: regulate the couplings, re-tune
notches if it has to be moved and then the bandpass tunings. Execute the sequence in small steps aiming to
improve the matching.
MEASURE
> 26dB
Attenuation @ V.C.-INTERCARRIER
> 25
Attenuation @ V.C.+INTERCARRIER
> 20
Date
D.T.
54
VALUE