Professional Documents
Culture Documents
Sheet
Dolit HB
Issue 12/07
D.130
Dolit HB
Potassium Waterglass cement
1. Product Description
Dolit HB is a halogen-free water glass cement made of two components: Dolit HB Powder
and potassium water glass solution, which after mixing hardens through chemical
reaction. Dolit HB is a product out of our special protection materials range with the
following unique characteristics:
Waterproof material
2. Application Areas
Dolit HB is suitable for jointing of acid-proof bricks, tiles, special fabricated pieces, for
constructing apparatus and chimney linings.
Dolit HB exhibits excellent resistance to water and rinsing actions, which allow rinsing
even at acid and neutral range for several weeks and also permanent rinsing is possible.
Dolit HB is resistant to all acids except hydrofluoric acid, to solvents, to oxidising agents,
oils and fats but it is not resistant to alkalis.
3. Packaging
Packaging:
Dolit HB Powder:
Dolit HB Solution:
page 1 of 4
25 kg
310 kg
Bachstr. 38
D 53639 Knigswinter
Technical Information
Sheet
Dolit HB
Issue 12/07
D.130
4. Technical Data
Composition:
Dolit HB:
Silicate, halogen-free
Density:
Dolit HB Powder:
approx. 1,15 g/ cm
Density (mixture):
Proportion Dolit HB
Solution: K2O : SiO2
1: 1,88
Viscosity Dolit HB
Solution:
40 50 mPa s
Shore Hardness D:
> 20
Compression strength
(cylinders 25x25 mm):
Approx. 35 N/mm
(after 28 days stored at room temperature)
Compression strength
(Prism):
>18 N/mm
(after 28 days stored at room temperature)
Tensile strength
DIN 1048-5:
Approx. 10 N/mm
(after 28 days stored at room temperature)
Modulus of elasticity:
Coefficient of linear
expansion:
12 x 10-6 K-1
Heat conduction:
1,2 W / m x K
Temperature resistance:
+ 900 C
Dolit HB Powder:
Dolit HB Solution:
page 2 of 4
Bachstr. 38
D 53639 Knigswinter
Technical Information
Sheet
Dolit HB
Issue 12/07
D.130
5. Application Instructions
Surface preparation:
concrete:
Cleaning and contemporary roughening by shot-blasting
(e.g. Blastrac), pressure blasting or milling (after milling
shotblasting is necessary). Subsequently clean.
Surfaces to be coated have to comply with building
standards and must be solid and stable, free from
laitence, dirt, oil, fat, wax, water repellent agents or any
other adhesion disturbing intermediate layers. Residual
moisture content not above 4 % acc. to CM. Surface
tensile strength according to DIN 1048, part 2 should not
be below 1.5 N/mm and the lowest individual value may
not be less than 1,0 N/mm. With strong mechanical
load, the average standard reading should be 2.0 N/mm
and the smallest individual value 1.5 N/mm.
steel:
Blast cleaned to Sa 2 acc. to ISO 12944-4.
To avoid fresh rusting those surfaces have immediately
to be coated with a thin layer made of Dolit HB and Dolit
HB Solution (proportion1 : 1)
Application temperature:
Relative humidity:
(321 parts)
(100 parts)
Preparation of
the coating agent:
Pot life:
About 60 minutes at + 20 C
Application of the
components:
page 3 of 4
Bachstr. 38
D 53639 Knigswinter
Technical Information
Sheet
Dolit HB
Issue 12/07
D.130
A) primer (concrete ):
B) primer ( steel )
Painting / brushing
Apply evenly with a brush or roller of lambskin
Quantity needed for 1 sqm :
0,5 kg Dolit HB Powder + 0,5 kgDolit HB Solution
C) bedding / jointing:
With a trowel
Cleaning:
Thinner
Drying:
Accessible:
After 1 to 2 days
Loadable:
Curing:
Commissioning:
All information contained in this Product Information sheet is based on the present state of our knowledge and
practical experience. All data are approximate values for guidance only. A legally binding warranty of certain
characteristics or the suitability for a certain purpose of use cannot be derived from this.
The information given in this Product Information sheet is our intellectual property. The Product Information
sheet may neither be copied nor used by unauthorized parties, nor professionally distributed or otherwise made
accessible to third parties without our prior consent.
page 4 of 4
Bachstr. 38
D 53639 Knigswinter
Technical Information
Sheet
Dolit HB
Issue 12/07
D.130
Due to the fact that our products are subject to permanent control and increase of efficiency, possible
modifications may not yet have entered this issue. Therefore, you are kindly requested to contact us for further
technical advise.
We wish to point out that the offered materials are special products which require special knowledge and
experience.
page 5 of 4
Bachstr. 38
D 53639 Knigswinter