Professional Documents
Culture Documents
TECHNICAL MANUAL
11 kV Switchboard
SECTION 1
1/48
CONTENTS
SECTION 1 TECHNICAL
1.1.0
1.2.0
1.3.0
1.4.0
3
4
6
7
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
1.14
8
8
9
9
9
9
10
10
10
10
11
11
11
12
1.15.
1.16.
1.17.
1.18.
1.19.
12
12
13
14
15
OVERVIEW
BASE UNIT WITH ADVANCED USER-MACHINE INTERFACE
HARDWARE CHARACTERISTICS
ADVANCED UMI FRONT PANEL CONTROLS AND OPERATION
ELECTRICAL CHARACTERISTICS
16
1.20.
16
OVERVIEW
SECTION 1
2/48
Indoor / IP3X
Satin grey white RAL9002 to DIN Standards
Vacuum CB with series disconnector
1250A
11kV, 3 phase, 3 wire, earthed neutral
50Hz
25kA rms, 3 seconds
95kV
refer to individual specification sheets
from above, at rear of LV cabinet
24V DC
1x
Switchboard Ancillaries
3x
VC2-P7
1x
BUSBAR VT
Switchboard Ancillaries
The table below shows the switchboard generic ancillary items which are included in our offer. Should any of the items shown as not
included be required, or for further details please contact us. Alternatively, please also refer to the GenieEvo Selection Guide.
Not included
Not included
Not included
SFT2841
setting/oscillography
software on CD for
Sepam relays
Heat shrink
terminating kits
Included
Not included
SECTION 1
3/48
1.1.1 VC2-P7
This panel type provides a comprehensive protection package for switchboards with one transformer incomer, or dual transformer incomers
without directional overcurrent protection. It also includes monitoring of the transformer winding temperature and Buchholz devices for
local and remote indication of operation. This includes extensive circuit breaker metering, monitoring and control features as standard and is
ideally suited for integration into a supervisory system using its optional RS485 serial link interface.
environment
Protection
ratings
short time withstand : 25kA, 3 seconds
normal current rating : 200A
dimensions (mm) : 1900 H x 500 W x 1200 D
Control functions
trip/close CB control
trip circuit supervision (74)
external protection trip
remote emergency trip
intertrip send/receive
CB close inhibit
lockout (86)
logic selectivity block send/receive
winding temp / buchholz
operating mechanism
independent manual stored energy (motorised)
test facility
integral cable test and earthing (fully interlocked)
CT secondary injection test terminals (LV cabinet)
circuit breaker vacuum interrupter test (fully interlocked)
phase currents
record of tripping currents
maximum demand currents
phase voltages
kW, kVA, KVAR, power factor
kWh, kVARh
kWh pulsed output
thermal capacity used
disturbance recorder when SFT2826 software used
cable termination
main cable entry : Bottom entry
connection type : direct connection to ANSI bushing
cables up to 300mm (1x3c) / up to 630mm (3x1c)
Optional features
Mechanism motorisation
30V DC
Not included
SECTION 1
4/48
No Relay kit
Gland plate(s)
Not included
Not included
Control switches
Not included
Mechanism padlocks
To find out more about GenieEvo range, please refer to he Selection Guide, or visit our website at : www.schneider.co.uk
ratings
normal service voltage: 13.8kV
cable termination
cable entry : Bottom entry
cable connection type : 1 x Bushing Sleeve
per phase
cables up to 300mm
MV Gland(s) : Not included
MV gland plate : 1x3c gland plate
To find out more about GenieEvo range, please refer to the Selection Guide, or visit our website at : www.schneider.co.uk
SECTION 1
5/48
3.1.3. BUSBAR VT
This unit type offers a busbar connected VT.
environment
location : indoor, IP3X
ambient temperature : -5 to +40oC
altitude : upto 1000m above sea level
ratings
normal rated voltage : 13.8kV
dimensions (mm) : 1900 H x 500 W x 1200 D
To find out more about GenieEvo range, please refer to the Selection Guide, or visit our website at : www.schneider.co.uk
SECTION 1
6/48
The panels are composed of the following compartments, fully segregated by steel partitions :
Circuit breaker MV compartment
MV cable connection compartment
MV busbar compartment
LV cabinet
LV cable connection compartment
CT compartment
VT compartment
Access :
SECTION 1
7/48
isolator utilised on GenieEvo is unique in design, employing a controlled air environment in a fully
encapsulated cast resin earth screened envelope. The sealed for life design is impervious to the local
environment ensuring that the series isolator is totally maintenance free.
Cable testing is facilitated via the series isolator, following initial application of earth and subsequent operation
of interlocks. With GenieEvo there is no requirement for a loose test access key. Access to the normally
earthed star point connected to the cables is at the front of the equipment. There is no requirement to enter
the MV cable box during cable testing.
1.7. Busbar Earthing and Testing Facilities
When a bus-section unit is employed, the busbars to either the right-hand or left-hand side of the unit in turn
may be earthed by means of the units fully interlocked series isolators.
As a preventative method against inadvertent maloperation, key type mechanical interlocks in conjunction with
wall mounting key exchange boxes are optionally available.
1.8. Low Voltage Wiring
Secondary wiring on each panel comprises our standard arrangement which utilises suitably rated PVC
insulated stranded copper wire coloured black. Mains 230 volt a.c terminations will be segregated and
shrouded.
1.9. Anti-Corrosion Protection and Finishing
To permit the use of GenieEvo range under onerous climatic conditions, a systematic, comprehensive finishing
process is adopted. A copy of our detailed finishing specification can be made available upon request.
1.10. Labelling
The unit data label is fitted at the unit front identifying the unit serial number, panel type and ratings.
Blank engravable circuit identification labels are provided at the front and rear of each panel. The styling is
black lettering on a white background. Internal devices, such as VTs and CTs are identified by separate
permanent adhesive labels located within the LV cabinet. All labels and literature will be in the English
language.
SECTION 1
8/48
Standards
Current transformers
Voltage transformers
National
BS 3938
International
National
BS 3941
International
National
Relays
IEC 60044-1
IEC 60044-2
BS 142
International
IEC 60255
Panel
Weight
Standard panels
Bus-sections
Dimensions
width
height
depth
365 kg max
500 mm
1900 mm
1200 mm
560 kg max
1000 mm
1900 mm
1200 mm
SECTION 1
9/48
All the data required for local equipment operation may be displayed on
demand :
> Display of all measurement and diagnosis data
> Display of operating and alarm messages, with alarm
acknowledgement and Sepam resetting
> Display of the list of activated protection functions and the main
settings of major protection functions
> Adaptation of activated protection functions set points or time delays in
response to new operating constraints
> Display of Sepam and remote module versions
> Relay output testing and logic input status display
> Entry of 2 passwords to protect parameter and protection setting
9-key keypad
>
Keys identified by pictograms for intuitive navigation
>
Menu guided access to data
SECTION 1
10/48
SECTION 1
11/48
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
SECTION 1
12/48
Sensor inputs
Phase current inputs
1A CT
Input impedance
< 0.001
< 0.001 VA (1A CT)
3 In
100 In
Consumption
Continuous thermal withstand
1 second overload
Voltage inputs
Phase
Residual
Input impedance
Consumption
Continuous thermal withstand
1 second overload
> 100k
< 0.015VA (100V VT)
240 V
480 V
> 100k
< 0.015VA (100V VT)
240 V
480 V
Relay outputs
Control relay outputs O1 to O4
Voltage
Continuous current
Breaking capacity
DC
AC (47.5 to 63Hz)
Resistive load
Load L/R < 20ms
Load L/R < 40ms
Resistive load
Load p.f. > 0.3
Making capacity
24/48 VDC
127 VDC
220 VDC
8A
8A/4A
6A/2A
4A/1A
8A
0.7 A
0.5 A
0.2 A
8A
0.3 A
0.2 A
0.1 A
8A
5A
< 15 A for 200ms
DC
AC (47.5 to 63Hz)
L/R load < 20ms
Load p.f. > 0.3
24/48 VDC
127 VDC
220 VDC
2A
2A/1A
2A
0.5 A
2A
0.15 A
Power supply
Voltage
Maximum consumption
Inrush current
Acceptable ripple content
Acceptable momentary outages
24 to 250 VDC
-20% / + 10%
10 to 16 W according to configuration
< 10 A 10 ms
12 %
100 ms
Battery
Format
Service life
AA lithium 3.6V
10 years Sepam energised
8 years Sepam not energised
SECTION 1
13/48
SECTION 1
14/48
SECTION 1
15/48
SECTION 1
16/48
SECTION 1
17/48
SECTION 1
18/48
SECTION 1
19/48
SECTION 1
20/48
SECTION 1
21/48
SECTION 1
22/48
SECTION 1
23/48
SECTION 1
24/48
SECTION 1
25/48
SECTION 1
26/48
SECTION 1
27/48
SECTION 1
28/48
SECTION 1
29/48
SECTION 1
30/48
SECTION 1
31/48
SECTION 1
32/48
SECTION 1
33/48
SECTION 1
34/48
SECTION 1
35/48
SECTION 1
36/48
SECTION 1
37/48
SECTION 1
38/48
SECTION 1
39/48
SECTION 1
40/48
SECTION 1
41/48
SECTION 1
42/48
SECTION 1
43/48
SECTION 1
44/48
SECTION 1
45/48
SECTION 1
46/48
SECTION 1
47/48
SECTION 1
48/48