Professional Documents
Culture Documents
SCOPE OF WORK
The scope of work under this specification shall include design, manufacture, testing
and inspection at manufacturers work, supply, receipt of material, unloading and
storage at site, erection, testing and commissioning of Coal Handling System for the
subject power station including to the following:
1
Crushers
Vibrating Screens
Stacker-cum-Reclaimer
Conveyors
Traveling trippers
10
11
2.00.00
DESCRIPTION
2.00.01
As a long term transportation option coal will be transported by rail and received at
site marshalling yard from the nearby SECL coal fields. The coal will be unloaded on
track hopper and fed to the belt conveyor by plough feeders or vibrating feeders. The
coal shall be conveyed through the tunnel and fed through belt conveyors to the
crushers. In-motion weigh bridges or in-line belt weighing machines are required to
be provided for better accounting procedures on quantity of coal received and taking
stock.
2.00.02
Double stream belt conveyors are envisaged from track hopper upto crusher house.
Necessary dust suppression system to the coal unloading above ground hopper and
the track hopper will be provided.
2.00.03
Capacity of the unloading, crushing and stacking system will be to meet peak coal
receipt.
2.00.04
ROM Coal may also be received by road trucks in emergency. Coal will be
discharged into a separate truck-unloading hopper from the trucks or dozed into the
track-hopper and feed to crusher. Necessary ramp to suit unloading of coal from
tipper trucks will be provided.
1 Of 49
TECHNICAL SPECIFICATION
2.00.05
Crushing System
The coal unloading conveyors will feed the crushers located in the crusher house to
crush the coal size to (-) 20 mm size for feeding the boiler bunkers. The under size
coal present in the coal will bypass the crusher. This under size is separated in the
vibrating screen and conveyed to the forward run.
Necessary inline magnetic separators will be provided on the conveyors feeding the
crusher house. Adequately sized surge hoppers/ feed chutes / flap gates will be
provided to have maximum flexibility in the flow of material. The crushing and
screening system will be 2x100%. Crushers shall be supported on RCC foundation
and shall be isolated from other foundation work. Necessary anti-vibration dampers
will be provided for the crusher foundation as required.
2.01.00
2.02.00
2.03.00
2 Of 49
TECHNICAL SPECIFICATION
2.04.00
Control Room
The complete coal handling system operation will be controlled from coal handling
control room located in the plant near to crusher house. The stacker/ reclaimer will
be operated from operators cabin located on the machine.
2.05.00
3.00.00
3.00.01
The specifications as brought out for mechanical & electrical equipment shall be
applicable to the system of proposed coal handling system and specifically to all
mechanical equipments including their operation & control philosophy. However,
some specific parameters of the entire coal handling system as a whole and the
major equipment are brought out as under.
3.00.02
3.01.00
TRACK HOPPER
A track hopper of 210 M length shall be provided. The capacity of hopper shall be
about 3000 MT of coal. At the outlet of track hopper four (4) plough feeders with
hydraulic drives will be provided for each stream. The capacity of the plough
feeders will be suitable for unloading coal at a rate of at least 3 rakes a day in an
emergency situation. The walkway in the tunnel will be minimum 1000 m clear of
the festoon cable trolley arrangement .The plough feeders will also be capable of
being operated from the tunnel floor. The machinery hatch will be able to
accommodate at least two (2) plough feeders at a time. The tunnel below the track
hopper will be provided with 3 sumps with two (1W+1S) sump pumps in each
sump. The sumps will be provided on either side in staggered manner. The drive
motor of all the sump pumps will be mounted at least 1.0 metre above the floor /
ground level. The sump pumps will be suitable to handle coal slurry and impeller
will be of non-clog type. The impeller will be of alloy cast iron with a hardness of
340 BHN.
3 Of 49
TECHNICAL SPECIFICATION
The grid will be located on the cone portion of the hopper about 1 to 1.5 m below
the top of the hopper. The line side equipment will include two (2) separate (1w
+1s) compressors. The side wall angle of the track hopper will be minimum 65 deg.
Two (2) access shafts in a staggered manner will be provided on either side along
the length of the track hopper. The track hopper will be provided with minimum 10
mm thick TISCRAL/ SAIL HARD liners. The opening in the grid will be suitable for
passing 200-mm coal lumps. The track hopper will be provided with a canopy and
should have a overhead electric power line for electric traction. The canopy will be
provided with lighting.
3.02.00
3.02.1
DESIGN REQUIREMENT
a)
Crusher shall be capable of handling the amount of coal as per enclosed Data
Sheet A even under maximum moisture content condition and shall reduce
the feed size of indicated hard grove index to the size stipulated in the data
sheet.
b)
c)
d)
The coal gets crushed due to shear and impact hammering due to the bar
hammer as the coal is dragged inside the wedge gap by the rotor of the
crusher. Adjustable balancing weights shall be provided on both sides of the
rotor to help achieve proper balance. The drive to the crusher shall be
through reversible electric motor connected through a fluid coupling. Drive
assembly shall be selected with V-belt / flat belt drive with hydraulic coupling.
The motor rating shall be selected considering 20% margin over requirement
at designed capacity.
e)
Secondary side of hydraulic coupling can start rotation only at 90% motor
cylinder speed. Hydraulic coupling can transmit the rated torque at max. 3%
slip.
f)
The crusher shall be provided with a facility for collection of larger tramp iron
to prevent damage from un-crushable materials and its automatic discharge,
if possible. High impact and wear resistant manganese shall be used in all
highest and greatest wear areas.
g)
Noise level and vibration shall be low and must be below 85 db at a distance
of 1 M away from the crusher & 1.5 M above the ground level at no load and
load. Vibration isolation system comprising of Gerb springs and visco
dampers shall be provided.
4 Of 49
TECHNICAL SPECIFICATION
h)
3.02.02
ii.
iii.
5 Of 49
TECHNICAL SPECIFICATION
(IMPACTOR CRUSHER)
Description
1
Unit
Type
Data particulars
Reversible Impactor
hammer Type
2.
Capacity
TPH
800 (Rated)
3.
Quantity
Nos.
TWO (2)
(1 running & 1 standby.)
4.
Material handled
5.
.
Density of material
6.
Moisture Content
7.
HGI
50
8.
mm
300
9.
Output Size
mm
10.
11.
12
13.
Material
a) Rotor
ROM Coal
T/M3
%
Fluid
Hrs/day
24
yes
b)
c)
Impact Arms
Gears
d)
Frame
Rolled Steel
e)
Material of liners
Manganese Steel
on housing
f)
Cage assembly
Mn steel
g)
Breaker plate
Mn steel
14
(i)
(ii)
15
Lot
Lot
Vee/ flat belt drive
VOLUME III, PART-A
SECTION 04
6 Of 49
TECHNICAL SPECIFICATION
16
Yes
Note:
1. The crusher motor shall be complete with temperature scanner and indicator,
speed switch and all accessories.
2. The crusher RPM and Motor RPM shall not exceed 600 & 1000 RPM (Syn.)
respectively.
3.03.00
VIBRATING SCREEN
3.03.01
DESIGN REQUIREMENT
a)
The vibrating screen shall be suitable for continuous duty and robust in
construction. it shall be capable of absorbing shock loads due to impact of
falling large coal lumps upto 300 mm size and other heavy metallic
components / pieces without damaging the roller disc. An Impact drum before
/ on vibrating screen, if required, to take care of impact of falling coal shall be
provided by Bidder as a part of the scope.
b)
The screen rolls with eccentric disc of solid alloy steel shall be provided. The
disc shall be mounted on the shaft running in antifriction bearings. Labyrinth
seals with grease chambers permitting re-lubrication and sealed off against
ingress of dust shall be provided. All rollers shall be so designed that these
can be operated under the worst condition of operation with wet and muddy
coal. The shaft material shall be as per approved manufacturers standard.
c)
d)
7 Of 49
TECHNICAL SPECIFICATION
VIBRATING SCREEN
1.
Location
2.
Duty
Continuous
3.
Capacity
4.
Number Required
TWO (2)
5.
Material to be handled
R.O.M. Coal
6.
(-) 300 mm
7.
8.
Output Size
Material for construction
(-) 20 mm
i)
ii)
iii)
Discs
Shafts
Gear
9.
20%
10.
8 Of 49
TECHNICAL SPECIFICATION
3.04.00
CRUSHER HOUSE
3.04.01
DESIGN REQUIREMENT
a) The Crusher house building shall be designed to accommodate the discharge and
feeding ends of conveyors including drive arrangement, crushers complete with
drive units, vibrating screens with drive units and necessary chute work., dust
extraction and ventilation equipments, tramp iron trolley, lifting tackles including
monorail etc.
b) The crusher house shall be of structural steel construction with suitable side
cladding. The crusher house will be provided with ample space for maintenance
and inspection of various equipments. Necessary steel doors, windows, exhaust
fans and roof extractors shall be provided to allow natural light and ventilation.
The dust extraction unit for crusher house shall be housed at the roof of the
building. The floors of the crusher house would be of RCC slab supported on steel
beams. Each crusher will be provided with independent foundation, separate from
the crusher house building foundation so that vibrations due to running of the
crusher are not transmitted to the entire crusher house building.
CRUSHER HOUSE
Description
Data / Particulars
Equipment
to
be
housed in the building
Staircases
NOTE
1. Crusher House building shall be provided with floor sweeping chutes for each
floor of the crusher and chute shall be brought upto the ground level and then
drained to the nearest plant drainage.
2. Roof extractor shall be provided in crusher house for better ventilation
9 Of 49
TECHNICAL SPECIFICATION
3.05.00
3.05.01
3.05.02
DESIGN REQUIREMENT
3.05.02.01
Mobile Tripper
a)
The Mobile tripper on bunker conveyors shall be motor driven type. It shall
consist of structures, supports, walkways, rails, belt scrapper with adjustable
rubber strip, rubber lagged head and bend pulleys complete with shaft
bearings, chutes, stops, limit switches, brakes etc. The tripper shall have
provision for dropping coal on both sides of conveyor into the bunker and
back to the conveyor for the purpose of skipping intermediate bunkers. The
rating of tripper travel motor shall be adequate to move the tripper smoothly
either in same or opposite direction to belt direction under fully loaded
conditions. Adhesive weight requirement and tractive effort calculations shall
be subject to approval of Purchaser. Coefficient of adhesion shall be
considered as maximum 0.15. Minimum two drive axles shall be provided for
tripper travel. Arrangement shall be provided at the starting point of the tripper
to avoid folding of belt.
In case of tripper running at a speed more than its rated speed due to chute
jamming or other reason, conveyor shall trip and annunciation shall appear.
b)
Supply of adequate length of rails to cover the runway length for the motor
driven tripper shall be included. The supporting structures for the rails with
necessary end stops shall also be supplied under this specification. Suitable
belt hold down guide pulleys shall be provided over the concave curve of belt
over tripper.
c)
The Bidder shall include necessary electricals for traveling trippers such as
motorised cable reeling drum with trailing cables, cable trays for resting the
trailing cables and end limit switches for protection against over travel of the
tripper. The cable reeling drum and trailing cable of each tripper shall be
suitable for the entire length of the bunker bay. Mechanical track stops shall
also be provided. The cables shall have copper conductors, proper insulating
material and braided armouring in accordance with IS:691.
Complete
Telephone Communication system between mobile tripper and CHP control
room is in Bidder scope.
d)
The travelling trippers shall be provided with fail safe A.C. thrustor operated
brake of totally enclosed type which shall engage as soon as tripper travel
10 Of 49
TECHNICAL SPECIFICATION
motor stops. A.C. Thrustor operated rail clamps with hand operation facility
from either side of the tripper shall also be provided.
e)
3.05.02.2
Monorail & electric hoist shall be provided for lifting conveyor drum to bunker
floors. Monorail shall be provided all along the bunker conveyer to facilitate
maintenance of tripper.
3.05.03
CONSTRUCTION REQUIREMENT
3.05.03.1
Mobile Tripper
i. Suitable dust cover shall be provided over tripper head pulley. Serrated
rubber seal shall be provided at open side to prevent dust nuisance. Suitable
dust tight access doors shall be provided. Counter-weighted type belt cleaner
shall be provided below the tripper head pulley for cleaning the carrying side
of the belt.
ii. The tripper shall run on rails (90 lbs/yard) with double flanged wheels. Rails
for tripper travel shall be mounted on supporting structure of respective
conveyors.
iii. Suitable system for monitoring position of tripper shall be provided.
addition, travel end limit switches and end stops shall also be provided.
In
iv. Suitable access platform of chequered plate with ladders, handrailing and
walkways on both sides shall be provided for access/maintenance of
equipment on tripper. In addition, crossover platform shall be provided with
tripper so that operator can cross the belt through the same.
v. Suitable rail cleaners shall be provided on leading and trailing edge of tripper
for either track.
vi. 3mm deck plate continuous shall be provided below carrying idlers on the
trippers.
vii. For specification of flap gates/actuator on trippers relevant clauses of this
specification shall be referred to.
viii. Provision shall be kept for automatic tripping of bunker bay conveyor in the
event of travelling tripper getting dragged (i.e. travel speed in excess of rated
speed).
11 Of 49
TECHNICAL SPECIFICATION
TRAVELLING TRIPPER
1.0.0
GENERAL
1.1.0
Mobile Tripper
1.2.0
2.0.0
2.1.0
Mobile Tripper
2.1.1
Mounting
2.1.2
Drive
2.1.3
Pulleys
(a)
Rubber lagged
2.1.4
Brakes
2.1.5
Clamps
2.1.6
Walkways
2.2.0
2.2.1
Sealing Belt
As specified
2.2.2
Guide Rollers
As per requirements.
2.2.3
Bunker Slot
(a)
Width
(b)
(a)
3.06.00
3.06.01
DESCRIPTION:
a) The stacker reclaimer unit shall be provided to stack the material onto the pile or
reclaim the stockpiled material and feed onto the conveyor for bunker feeding.
LANCO TPS- 300 MW UNIT # 2
EPC SPECIFICATION
NIT DOC. NO. D-51123-LAPPL
12 Of 49
TECHNICAL SPECIFICATION
b) The rail-mounted machine shall be controlled from the operators cabin located
on the machine to avail the maximum range of vision to the operator.
3.06.02
3.06.3
Superstructure,
Counter-weight boom,
Intermediate conveyor,
Tripper,
Chutes,
Rail clamps,
Operators cabin.
Bucket Wheel:
13 Of 49
TECHNICAL SPECIFICATION
3.06.4
Luffing Device :
Hoisting or lowering of the bucket wheel boom will be done hydraulically. The upper
and lower positions of the bucket wheel boom shall be limited by control & limit
switches.
3.06.5
end.
3.06.6
Slewing Mechanism :
The slewing mechanism shall have direct current drives. The D.C. drives shall be
powered via thyristor panel.
The slewing mechanism brakes shall be actuated by thrustors when the slewing
motors are switched.
Slewing shall be around + 105 deg.
3.06.7
Travel Mechanism :
The rail travel mechanism shall have necessary drives. The travel mechanism brakes
shall be actuated by thrustors when the motors are switched. It shall have also
manually operated rail clamps.
The travel mechanism shall be provided with two electro hydraulic operated rail
clamps monitored by limit switches (open & close positions).
The main cable reeling drum and the control cable reeling drum shall be built-on to
the lower frame each of which is driven by an individual Stall torque motor.
3.06.8
Super Structure :
The super-structure shall be of welded plate construction and supported on the
slewing ring. The bucket wheel boom alongwith mast and counter weight boom is
supported onto the super-structure. The hydraulic for the luffing is also supported
to the super-structure.
3.06.9
Lower Carriage :
The lower carriage shall be of sturdy box type design and it is supported on the
travel mechanism
LANCO TPS- 300 MW UNIT # 2
EPC SPECIFICATION
NIT DOC. NO. D-51123-LAPPL
14 Of 49
TECHNICAL SPECIFICATION
3.06.10
Operators Cabin :
The operators cabin shall be made of sheet metal. Adequate number of glass
panels shall be fitted to provide panoramic view.
Chute :
Necessary chutes would be fabricated from IS:2062 Gr.A/B for mother plate and
liner plate out of 5mm thick SS304
3.06.12
3.06.13
Intermediate Conveyor :
The intermediate conveyor would comprise of the structure, walkway with open
grid flooring, railing, belt scraper, head pulley with drive unit, impact idler for
receiving material, chute and supports of welded construction with single wheel
bogies.
3.06.14
Tripper :
A tripper would be provided to operate in conjunction with main line conveyor.
The tripper would comprise of structure, walkway with open grid flooring, railing, belt
scraper, head pulley, bend pulley, chute and supports of welded construction with
single wheel bogies.
The tripper travels on the same rails as those of the main machine. The tripper
discharge end is supported on the support car.
3.06.15
MODE OF OPERATION
3.06.15.1
Control System
Stacker/Reclaimer control shall have the following type of control :a)
Bucket Wheel boom with Cabin operated raise / lower control through joystick
controller, amplifier card for proportional solenoid valve of boom luffing
hydraulic system.
15 Of 49
TECHNICAL SPECIFICATION
Bucket Wheel boom with Cabin operated (slewed) step less control of Slew
platform DC drive through joystick controller.
b)
The long travel motion of stacker cum reclaimer shall be through two speed
squirrel cage motors, soft starter.
c)
d)
3.06.15.2
Protection
Following protections shall be provided :
3.06.15.2.1
Bucket Wheel :
a)
Slip monitor.
b)
3.06.15.2.2
3.06.15.2.3
3.06.15.2.4
c)
d)
Boom Conveyor :
a)
b)
c)
Hoist :
a)
b)
c)
Slewing :
a)
b)
c)
16 Of 49
TECHNICAL SPECIFICATION
3.06.15.2.5
Travel :
a)
b)
Buffers
c)
d)
3.06.15.2.6
1.
2. Operation of the overload relays for any of the motors shall trip the main
supply breaker to cut off power supply to all the motors.
3. Undervoltage interlock shall be provided to operate the main supply breaker
and open the main breaker contacts and its holding contact.
4. `Start push button of the main supply shall be wired in series with `OFF
position contacts of all the controllers, thus requiring that all controller handles
are in `Off position before the main supply breaker can be switched on.
5. `Deadman contacts on all the controllers shall be wired in series to open out
the main breaker.
6.
Emergency pull wire switch, belt sway switches and zero speed switches.
17 Of 49
TECHNICAL SPECIFICATION
STACKER-CUM-RECLAIMER
1.0
GENERAL
1.1
Type
1.1.1
Location
Outdoor
1.2
Numbers required
One (1)
1.3
800TPH
1.4
800TPH
1.5
Duty
1.6
20 m/s
47 m/s
1.7
Seismic co-efficient
1.8
Material handled
1.8.1
Material
1.8.2
Bulk density
1.8.3
Moisture content
20 percent maximum
1.8.4
Angle of repose
37 deg.
1.9
Boom Length
1.10
To suit stock-pile
1.11
8m
1.12
18 Of 49
TECHNICAL SPECIFICATION
a)
b)
c)
d)
e)
Type of construction
Material of
construction
Type of construction
:
:
6 Nos.
Number/Truck
Number/Carriage
Material of wheel
Wheel dia./base
No. of driven wheels
Total no. of wheels of
main unit
:
:
:
:
:
:
Two (2)
6 Nos. per carriage
Cast alloy Steel, 42 Gr.M04
630/820 mm
12 Nos.
28 Nos.
1.13
1.17
Stability factor
a)
b)
1.5
c)
Material of construction :
I.
ii.
ii.
Bucket Wheel :
M.S., IS:2062
Bucket
:
Abrasion resistant steel
Lips :
Magnese Steel
b)
suitable
19 Of 49
TECHNICAL SPECIFICATION
3.07.00
c)
Yes
d)
e)
f)
g)
Yes
46 (approx.)
The design, manufacture, inspection and testing of the Belt Conveyor System
shall comply with all the currently applicable statues, regulations and safety codes
in the locality where the equipment is to be installed. The belt conveyor system
shall confirm to the latest edition of the following standards & codes. Other
internationally acceptable standards/codes, which ensure equal or higher
performance than those specified, shall also be accepted. Nothing in this
specification shall be construed to relieve the Bidder of the required statutory
responsibility. In case of any conflict in the standard and this specification, the
decision of the Purchaser shall be final and binding.
Belt Conveyors for Bulk Materials published by Conveyor Equipment
Manufacturers Association.
IS:7155 : Codes of Practice for Conveyor Safety.
IS:1891 (Part-I) : General Purpose Belting
IS:8598 : Idlers and Idler Sets for Belt Conveyors
IS:4009 (Part-II) : Conical Head Grease Nipples
IS:8531: Pulleys for Belt Conveyors.
IS:226 : Structural Steel (Standard Quality)
IS:4682 : Codes of Practice for Lining of Vessels and Equipment for Chemical
Processes.
IS:11592 :Code of practice for selection and design of Belt Conveyors.
CAN / CASA - M422 M87 : Canadian standard association.
20 Of 49
TECHNICAL SPECIFICATION
3.07.02
DESIGN REQUIREMENT
3.07.03
CONSTRUCTION REQUIREMENT
3.07.03.1
Belting
The specification of Belting for conveyors shall be as follows:
(i) Material and Width of the Belt :
5/2 mm
630/4 FR grade
600TPH
i. The sealing belt (for sealing slots of tripper floor) shall also be of suitable width
with synthetic cover. Bidder shall provide sealing belt for all Bunkers
ii. Carrying idlers shall be provided with three equal rolls with troughing angle of
35 deg. and 2 deg. forward tilt .
iii. In no case, shall the diameter of the idler roll be less than 152 mm for both
carrying side and return side.
iv. Roller used in idlers shall be made from ERW steel tube. Wall thickness shall
be minimum 4.0 mm without any negative tolerance. The rollers shall be
mounted on EN-8 or equivalent material spindles by means of heavy duty ball
bearings, preferably seize resistant type (SKF/Equivalent), of 30 mm size for
carrying idlers and 20 mm size for return idlers. The bearings shall be
adequately sealed and lubricated for life. The rolls shall be supported from
fabricated steel brackets. Fixing arrangement of rollers with brackets shall be
drop-in type. For adjusting the alignment of the idlers, slotted holes shall be
provided in idler supporting base plates.
LANCO TPS- 300 MW UNIT # 2
EPC SPECIFICATION
NIT DOC. NO. D-51123-LAPPL
21 Of 49
TECHNICAL SPECIFICATION
v. Idler rollers shall be waterproof, dust proof and weather proof against a high
velocity water jet. All idlers shall be provided with minimum double labyrinth
dust seal.
vi. Impact idlers used at the loading and transfer point shall be so designed as to
avoid direct loading impact, belt damage and excessive punishment to the
carrier. The material used in construction of this type of idlers shall be of
resilient type.
vii. The return idlers for all conveyors shall be single roll type.
viii. The self-aligning idlers shall be direct acting type, complete with actuating
rollers fitted with the ball bearings and mounted inclined towards the belt. The
idler frame shall be suitably cradled about a vertical pivot, supported in bearing
over a fixed plate.
ix. Transition type troughing idlers shall be used adjacent to all pulleys to permit
proper support of the loaded belt near the pulleys without excessive stretch of
the belt edges. The transition idlers shall be provided with preferably adjustable
concentrator (end) rolls and long center rolls to suit the troughed belt contour
between the last regular troughing idler and the adjacent pulleys. The transition
length and the number of the transition idlers shall be selected depending upon
the tensions, type and size of belt, number of plies and other necessary
governing factors.
3.07.04
Belt Cleaners
External Belt Cleaner
Spring loaded scraper type cleaner with modular segmented and replaceable
polyurethane scrapers blades complete with main cleaner, pre-cleaner (mounted
separately) along with accessories and necessary fines (reject of scrapper) chutes
shall be furnished for conveyors and head pulleys. The modular units shall be
easily replaceable. The scraper assembly shall be easily maintainable from outside
without any interference with the chute arrangement and assembly.
Internal Belt Cleaner
V-plough type belt cleaner made of mild steel flats and hard rubber strips with
automatic wear adjustment and necessary accessories shall be furnished for
cleaning internal surface of the conveyor belt.
3.07.05
3.07.06
Pulleys
i. All pulleys shall be provided as per requirements of the coal handling
system.
LANCO TPS- 300 MW UNIT # 2
EPC SPECIFICATION
NIT DOC. NO. D-51123-LAPPL
22 Of 49
TECHNICAL SPECIFICATION
ii. The snub pulleys on each conveyor shall be located to provide a belt wrap
on the drive pulleys of not less than 220 deg. wrap is envisaged for single
snub drive only.
iii. All drive pulley surfaces shall be hot lagged with vulcanised natural rubber
lagging grooved in diamond pattern.
iv. All non-drive pulleys shall be vulcanised natural rubber lagged (hot) with
plain lagging.
v. The rubber to be used for lagging of pulleys shall confirm to specifications
listed in data sheet of this section.
vi. The rubber lagging of pulleys and method of lagging and testing the same
shall conform to IS:4682.
vii. The pulleys shall be made from mild steel conforming to IS:2062 (Tested
Quality).
viii. All the pulleys shall be keyed to forged steel shafts of EN-8 or equivalent
material of adequate proportion running in heavy duty roller bearings with
proper greasing arrangement. The plummer blocks for pulleys shall be of
horizontally split type construction with minimum (4) nos. bolts holding the
two split halves and with min (4) nos. foundation bolts. The plummer blocks
shall be dust tight with double labyrinth seals. Conical head shape nipples
conforming to IS:4009, suitable drain plug and eye bolt shall be provided.
Side covers of plummer blocks shall be heavy duty metallic sheets. No
plastic components shall be used.
ix. Pulleys shall be mounted on machined & ground surfaces. Suitable guards
shall be provided for all tail pulleys and bend pulleys for safety of operating
personnel.
x. Suitable stiffening arrangements shall be provided in all pulleys. For
selection of pulley shaft dia of all the pulleys, a margin of atleast 20% shall
be considered on the maximum tension. Selection of pulley diameter, shell
thickness, stiffening and shaft diameter shall be subject to approval of
Purchaser.
xi. Pulleys of same diameter shall be completely interchangeable in totality
and component wise.
3.07.07
3.07.07.1
23 Of 49
TECHNICAL SPECIFICATION
3.07.07.2
3.07.07.3
3.07.07.4
3.07.07.5
i)
Belt loaded
ii)
iii)
24 Of 49
TECHNICAL SPECIFICATION
3.07.07.6
Drive Motors
H.T. motors shall be provided for crushers and any other equipment as required.
Rating of the drive motors in no case shall be less than 120% of the power
required at drive motor output shaft at specified design capacity. The motor rating
shall be at 50 deg C. ambient.
3.07.08
25 Of 49
TECHNICAL SPECIFICATION
BELT CONVEYOR
1.0.0
GENERAL
1.1.0
Design Capacity
110% of rated
800MTPH .
1.2.0
Maximum slope
14 degree
1.3.0
2%
1.4.0
Minimum Radius
capacity of
(i)
Concave curve
(ii)
Convex Curve
50 m
1.5.0
Coal Parameters
As specified
2.0.0
2.1.0
Belting
2.1.1
Type
AS specified elsewhere
2.1.2
Cover Grade
2.1.3
Face
5.0 mm (min.)
(b)
Bottom
2.0 mm (min.)
2.1.4
No. of plies
Minimum 4
2.1.5
Drive Arrangement
As specified elsewhere
26 Of 49
TECHNICAL SPECIFICATION
2.1.6
Factor of Safety
2.1.7
2.2.1
Type
(a)
10 (Minimum)
Carrying
(b)
Return
(c)
2.2.2
Loading point
Spacing
(a)
Carrying
(b)
Return
(c)
Loading point
(d)
Self-aligning
idlers
(e)
2.2.3
2.2.4
Impact type
troughing
Bearings
(a)
Carrying
(b)
Return
Materia
(a)
Roller
(b)
Spindle
LANCO TPS- 300 MW UNIT # 2
EPC SPECIFICATION
NIT DOC. NO. D-51123-LAPPL
E.N. 8 or equivalent.
27 Of 49
TECHNICAL SPECIFICATION
2.3.0
Belt Cleaners
2.3.1
External
2.3.2
Internal
2.4.0
2.5.0
Pulleys
2.5.1
16 mm
(ii)
24 mm
2.5.3
2.5.4
deflection 5 minutes
As specified elsewhere
Drive Pulleys
(1)
16 mm
(2)
Lagging
(3)
Lagging thickness
(4)
220 degrees
(5)
Other pulleys
(1)
16 mm
(2)
Lagging
(3)
Lagging thickness
12 mm thick plain
28 Of 49
TECHNICAL SPECIFICATION
(1)
Type
2.5.5
(2)
Hardness
55 to 65 durometer (Shore A)
(3)
Elongation
Over 300%
(4)
Strength
160-200 kg/cm2
(5)
Abrasion loss
(6)
Specific Gravity
1.4 to 1.5
(7)
Adhesion Strength
10 kg/cm (minimum)
Type
(2)
Casing
(3)
Sealing
(4)
Lubrication
2.5.6
Pulley Material
2.5.7
Shaft Material
2.6.0
2.6.1
2.6.2
2.6.3
EN-8
(1)
Type
(2)
Location
(3)
Spacing
Approx 30 m
or
Type
(2)
Spacing
Type, Location
29 Of 49
TECHNICAL SPECIFICATION
2.7.0
Drive Motors
2.7.1
Type
Three
Phase
Induction Motors
2.7.2
Base mounted
2.7.3
3.08.00
Squirrel
Cage
3.08.01
3.08.02
3.08.02.1
inclined surface at 60 degrees valley angle at the feeding point to guide the
material in the direction of belt travel. Further, chute construction below flap gate
shaft shall be such that there will not be any accumulation of coal dust between
chute and flap gate in that zone.
iv.
30 Of 49
TECHNICAL SPECIFICATION
Bottom side of the chutes on which the coal slides shall be welded to the side
plates to form a trough. Bottom sides along with its adjacent sides shall be
flanged and made from TISCRAL or equivalent material of 20 mm thickness.
The non striking surface i.e. the covers of the trough shall be of 10 mm thick mild
steel and bolted to the flange provided on the trough
vi. Bolted flange joints shall be of dust tight construction and necessary sealing
material shall be provided in all the flange connections for adequate sealing.
vii. Complete chute work in the region of flap gates shall be fabricated from
TISCRAL or equivalent. In case of vertical chute (valley angle more than 80
degree) complete chute work shall be of 20 mm thick TISCRAL or equivalent
material. While finalising the chute work inside the building, arrangement for
shifting and replacing chute legs, proper handling arrangement/wall openings,
trolleys, hoists shall also be provided.
viii. Hoods over the conveyor head pulleys shall be made of suitably stiffened
minimum 4 mm M.S. Plates and shall be provided with hinged and gasketed
inspection doors with suitable access to them. Further, serrated rubber seal shall
also be provided at the very inlet of head chute to minimise dust nuisance.
ix. Separate maintenance sealed door shall be provided for access to belt cleaners in
head pulley hood and shall be of hinged with positive locking facility.
3.08.02.2
Skirt Boards
Skirt board shall ensure centralised loading of conveyor belt to avoid coal spillage.
Suitable Skirt Plates of minimum 3.0 meters length shall be provided at each
feeding point of conveyor. The width of the Skirt Boards shall be two-third the
conveyor belt width. In the belts before Crusher House where coal of appreciable
lump size is being conveyed, the gap between the bottom of the skirt board and the
belt shall be made to increase uniformly in the direction of belt travel. The height of
the skirt boards shall be sufficient to contain the material volume as it is loaded on
the belt and shall not be less than 750 mm. The skirt plates shall be fitted with
modular segmented and replaceable rubber skirting pads having facility of adjusting
the pressure on the belt conveyor and shall have provision of on line removal for the
purpose of easy maintenance.
3.08.02.3
Flap Gates
i. The motor operated two (2) position flap gates shall be provided in transfer
chutes as specified and shall be complete with electrically operated actuators.
The gates shall be of robust construction and suitable for trouble free operation.
The face of the flap gate shall be made out of 20 mm thick TISCRAL or
equivalent material.
ii. The equipment shall be capable of being operated for at least 15 switchings per
hour at rated load and thrust and shall be suitable for 10 Nos. consecutive
switchings at rated load and thrust. The equipment shall be shop tested to prove
this requirement.
iii. The motor rating for the actuator shall be so selected as to provide sufficient
thrust for operation of the flop gates against the moving weight of coal and/or flap
31 Of 49
TECHNICAL SPECIFICATION
gate. The flap gate travel shall be in the range of 60 deg. to 70 deg. The motor
shall be completely dust tight.
iv. Lever arm shall be provided between actuator and flap gate shaft for obtaining
required thrust.
v. The actuators shall be capable of preventing any over travel. Suitable travel
dependent limit switches controlling the travel of the flop gates on either direction
shall be furnished. These shall be placed internal to the drive unit and shall be
completely dust-proof. The limit switches shall be capable of adjustments to vary
the total length of travel of the gates.
vi. Suitable thrust dependent limit switches shall be provided in the actuator, which
shall trip off the actuator motor in case of excessive thrust due to jamming of the
gates during its travel in either direction. The same shall also be integral to the
drive unit and shall be dust proof.
vii. Provision for alternative manual operation shall also be made using declutchable
hand wheel. The diameter of hand wheel shall be selected considering
convenient force to be applied by a single operator. However, minimum diameter
of hand wheel shall be 500 mm. Limit switch for safety of person operating the
hand wheel shall be provided.
viii. The material of shaft shall be EN-8 or equivalent. The diameter of the shaft shall
be suitable for motor stalled condition and associated twisting.
ix. Approach/maintenance platforms complete with the chequered plate floor, hand
rails, ladders etc. shall be provided for all flap gates.
x. Shaft & flap gate shall be tightly fitted to each other.
xi. On both faces of flap gate main plate, 20mm thick TISCRAL liner plate or
equivalent material shall be provided.
32 Of 49
TECHNICAL SPECIFICATION
GENERAL
1.0.1
Coal Parameters
2.0.0
2.1.0
Chutes
2.1.1
2.1.2
Material :
(a)
As specified
60 degrees
Chute work
10 mm thk MS
angle
Hoods
over
2.1.3
Size of Chutes
2.1.4
Inspection Doors
2.1.5
Chute Construction
(a)
Corners
(b)
Joints Bolted
(c)
Bolt size
Min. M-16
(d)
Bolts spacing
(e)
Fixing Arrangement
2.2.0
Skirt Boards
2.2.1
Length
2.2.2
Height
2.2.3
Width
Side plate
33 Of 49
TECHNICAL SPECIFICATION
Top cover
6 mm thk M.S.
2.3.0
Flap Gate
2.3.1
Type
2.3.2
Travel
2.3.3
Automatic operation
(i)
Drive
(ii)
(iii)
No. of Operation / Hr
(iv)
Protection
2.4.4
Manual Operation
(a)
Maximum effort
(b)
Minimum Handwheel
500 mm
Diameter
2.4.5
3.09.00
Diameter minimum
130 mm
(ii)
Material
EN-8
34 Of 49
TECHNICAL SPECIFICATION
3.09.01
3.09.02
Clamps
Rail Clamp shall be designed for holding the machine stationary. Rating of the rail
clamp shall be subject to the approval of Engineer.
Rail Clamp shall be actuated by compression springs. The spring shall apply the
clamping force directly on the Rail clamp mechanism without using lever arm
linkages once power supply is cut-off. The force transmission mechanism from
spring to rail clamp faces shall be very simple with minimum linkages.
3.09.03
CONSTRUCTION REQUIREMENT
3.09.03.1
Thruster Brakes
The electro hydraulic thruster shall be fitted with the brake. Limit switches shall be
provided for brake applied/released positions. The windings shall be provided with
class-B insulation suitable for 415V 10% at 50 Hz 5% and combined variation of
10%. Brake lining shall be asbestos with inter woven brass wires capable of
withstanding 200C temperature.
The lining shall be fixed to the shoe by counter sunk screws.
3.09.03.2
Clamps
Rail clamp shall be provided between the two travel wheels. Further, limit switches
shall be provided for Rail clamp ENGAGED and DISENGAGED signals.
Minimum clearance between the Rail clamp face and rail surface shall be 50mm.
However, this clearance may not be uniform for both the faces of Rail clamp
throughout the length of rails. Rail clamp shall operate satisfactorily under this
condition without the need for any adjustments.
Complete Rail Clamp mechanism shall be manufactured from forged steel.
35 Of 49
TECHNICAL SPECIFICATION
GENERAL
1.1.0
Brakes
1.2.0
Clamps
2.0.0
2.1.0
Brakes
2.1.1
Type
Electro Hydraulic
operated.
2.1.2
Braking Torque
2.1.3
Brake Shoes
2.1.4
Shoe lining
2.1.5
Max. Temperature
lining
2.1.6
Thrustor
2.2.0
Clamps
2.2.1
Rating
2.2.2
2.2.3
Limit Switches
2.2.4
2.2.5
Material
for
Mechanism
2.2.6
Thrustor
3.10.00
DRIVE EQUIPMENT
for
Thruster
brakes
A.C.
Rail
Suitable Drive Equipments like electric motors, gearboxes (where applicable), fluid
couplings (where applicable), flexible couplings and other accessories shall be
provided for conveyor systems, mobile trippers, cooling water pumps for oil cooling
of scoop type fluid couplings for H.T.drives, fans for ventilation system and other
equipments as specified. Various requirements for individual equipments shall be
taken into consideration while designing the associated drive equipments.
36 Of 49
TECHNICAL SPECIFICATION
3.10.01
3.10.03
3.10.03.1
Gear Boxes
i. Gear Boxes shall be of sealed type and mounted on machined or ground
surfaces.
ii. The gearboxes shall be designed for 24 hours continuous duty. For thermal
and mechanical rating of the gearbox the data sheet shall be referred to.
Gearboxes with cooling coils are not acceptable.
iii. The gears used shall be helical conforming to IS:3681 (latest revision) or worm
reduction units or spiral bevel speed reduction units conforming to suitable
Indian Standards. The dimensions of the shaft end shall conform to IS:3688 or
its latest revision. Above 40 kW drive rating, all gearboxes shall be helical or
bevel helical type only.
iv. Recommended oil grade shall be compatible with gear internals like material of
bearing, cages. Further, all gearboxes shall have suitable breather plugs,
dipstick, drain plug etc.
3.10.03.02
Couplings
A) Flexible / Rigid Couplings
Approved type of couplings shall be used for power transmission depending upon
duty requirements. The design of the coupling shall be such that it can take shock
and misalignment without sacrificing its efficiency. Geared type flexible coupling
shall be used on low speed side for all conveyors and other drives where gear box
is provided. Other couplings in the drives shall be either rigid or flexible type,
depending upon the requirement of equipment design and shall be finalised during
detailed engineering.
B) Fluid Couplings
Scoop tube type fluid coupling shall be provided for HT motors
Suitable
electrically operated actuators shall be provided for scoop tube operation from local
as well as remote. Suitable provision for alternate manual operation shall also be
kept. Separate pump with motor shall necessarily be provided for circulating the
37 Of 49
TECHNICAL SPECIFICATION
fluid coupling oil through oil cooler. Independent arrangement for forced cooling
water supply using 2X100% capacity pumps to oil cooler shall be provided by
Bidder. Suitable interlock using flow switches shall be provided in both oil as well
as water lines to trip the drive motor in the event of flow in either line falling below
acceptable levels. Suitable pressure indicators and flow indicators shall be
provided in the cooling water lines along with all-relevant valves, strainers and
accessories. Necessary isolation valves shall be provided in the oil / water line for
maintenance of any equipment in the line. Necessary interlock shall also be
provided so that the HT motor cannot be started from remote / local unless position
of scoop tube permits no load start of the motor. Tripping of downstream
equipment while the system is under normal operation shall result in scoop tube repositioning to permit no load run of the concerned HT motor.
38 Of 49
TECHNICAL SPECIFICATION
DRIVE EQUIPMENT
1.0.0
GENERAL
1.1.0
120% of actual
power at
drive motor output shaft at
specified design capacity.
H.T. Motors shall be provided
for Crushers and any other
equipment as required.
d) Ventilation Fans
*The actual power at drive motor output shaft shall be calculated after
considering all the losses of down the line equipments of the drive train.
2.0.0
2.1.0
Gear Box
2.1.1
Type
(a)
Below 40 KW
(b)
Above 40 KW
2.1.2
Service Factor
2.1.3
50oC Minimum
2.1.4
Mounting
On machined/ground
surfaces
39 Of 49
TECHNICAL SPECIFICATION
2.1.5
2.1.6
Duty
2.2.0
Flexible Couplings
2.2.1
Type
2.2.2
Rating
2.3.0
Fluid Couplings
2.3.1
Type
2.3.2
3.11.00
24 Hrs. Continuous
(a)
L.T. Motors
Traction type
(b)
H.T. motors
Rating
during unloading of coal. DE units shall also be provided for Crusher House ,
Bunkers and Bunker floor.
b. There will be two (2) service water pumps (1 working + 1 standby) which supply
water to (a) local water storage tanks of D.S. system of stockyard, transfer
houses, junction towers and crusher house. (b) Service water tap points for
plant cleaning, toilets etc. Each DS system will be provided with two (1 working
+ 1 standby) pumps.
c. The quantity of water to be sprayed for the stockyard DS system will be
40 Of 49
TECHNICAL SPECIFICATION
connecting coupling) will be provided for each floor of junction towers, transfer
houses and crusher house.
f. Each tap off point will contain isolating valve with quick connecting coupling to
stop the water spray when the concerned plant and equipment of coal handling
system do not operate.
h. Each DS System will be operated from the local control panels and will be
transfer points.
j. Water spray arrangement will be provided for two (2) waiting wagons before the
track hopper.
3.12.00
3.13.00
VENTILATION SYSTEM
3.13.01
GENERAL DESCRIPTION
The air quantity for mechanical ventilation system shall be estimated based on
equipment and solar heat loads and the temperature rise inside the building. Dust
extraction system shall be provided for tripper floor, crusher house etc. Exhaust clean
air shall be discharged at a suitable height above building.
3.13.02
41 Of 49
TECHNICAL SPECIFICATION
the Bidder of the required statutory responsibility. In case of any conflict in the
standard and this specification, the decision of the Owner shall be final and
binding.
IS:3588 :
IS:2312 :
3.13.03
3.13.03.1
3.13.03.02
DESIGN REQUIREMENT
Axial Fans
i.
Design duty point of the fan shall match with the average value of maximum and
minimum flow rates of the fan in the stable operation zone. The speed of the fan
shall not exceed 960 rpm for fan with impeller diameter above 450 mm and 1440
rpm for fan with impeller diameter 450 mm and less. The first critical speed of
rotating assembly shall be at least 25% above operating speed.
ii.
iii.
For design purpose out door ambient temperature shall be taken as 50 deg.C.
iv.
The motor shall be rated for continuous operation and conform to companion
electrical specification. However, motor rating shall not be less than the max.
power demand throughout the entire range of operation of fan.
v.
All fan mountings shall have adequate arrangement for vibration isolation.
vi.
The reverse flow through non-working fan shall be automatically and positively
prevented by Modutrol motor operated discharge dampers. The dampers shall
be made out of 18 SWG MS sheets.
vii.
Design duty point of the fans shall match with the average value of maximum
and minimum flow rate of the fan in the stable operation zone.
Filters
Metallic Filters
Metallic cleanable filters shall be provided as required. Maximum air velocity
considered shall be 2 m/sec. Metallic cleanable filters shall consist of V-fold
galvanised wire mesh inter spaced with a flat layer of galvanised wire mesh. The
density of the filter medium shall increase in the direction of airflow. Wire mesh edges
shall be suitably hemmed to eliminate the danger of abrasion during handling. Filter
medium shall be supported on either side by galvanised expanded metal casing.
Filter frame shall be constructed from galvanised sheet of thickness not less than 18
gauge.
HDPE Filters
HDPE filters should have an efficiency of 90% down to 5 microns. Velocity across
the filter shall be limited to 2.5 m/sec.
42 Of 49
TECHNICAL SPECIFICATION
High efficiency filter (for A/C purpose). Filtration efficiency shall not be less than
99.9% down to 5 microns. Pressure drop across the filter under clean condition
shall not be more than 10 mm wc.
3.13.04
CONSTRUCTION REQUIREMENTS
General construction details of various equipment under Bidders scope shall be
as elaborated in subsequent clauses below.
3.13.04.1
43 Of 49
TECHNICAL SPECIFICATION
VENTILATION SYSTEM
1.0.0
GENERAL
1.1.0
1.1.1
1.1.2
Equipment
Bunker floor
Axial fans
2.2.0
Axial Fans
2.2.1
Capacity
10%
more
requirement
of
actual
2.2.2
Head
20%
more
requirement
of
actual
2.2.3
Speed
(a)
(b)
mm
(c)
Critical speed
2.5.0
Filters
2.5.1.
Metallic Filters
(1)
2.5.2
2m/sec.
HDPE filters
(1)
Efficiency
(2)
Max. velocity
2.5 m/sec.
(3)
Testing
44 Of 49
TECHNICAL SPECIFICATION
3.14.00
3.14.01
3.14.02
DESIGN REQUIREMENTS
1. For the Hoists with more than 2.0 tonne lifting capacity or more than 10.0 M
lift, motor operated hoist blocks for both long travel and lift shall be provided.
Other hoist blocks shall be of hand operated type for both travel and lift.
However, monorails coming out of the building shall be provided with electric
hoist blocks, irrespective of load and lift. Adequate length of Cantilever shall
be provided in monorails to lower the equipment to ground level clearing the
building sidewalls.
2. The exact lift/travel and the number of the hoisting mechanisms and the mode
of lifting equipments to various floors of the buildings shall be as decided by
the Purchaser during detailed engineering. It shall preferably be avoided to
use one single hoist for handling more equipments. Clear height shall be
maintained when handling one equipment over other, in such case no
dismantling of any equipment is admissible. The center line of monorail shall
not deviate by more than 500 mm from the center of gravity of any equipment
that is to be lifted.
3. Monorails shall be extended outside the building to handle the equipment to
ground level. Suitable machinery well and removable handrailing/grating shall
be provided on various floors of buildings, as necessary.
4. Electrically operated monogirder type hoists shall consist of following major
components.
(a.) Electrically operated trolley complete with drive motor (Trolley travel
speed maximum 15 m/min.).
(b.) Hoist cable, hoisting block and hooks complete with drive motor
(Hoisting speed maximum 6m/min.).
LANCO TPS- 300 MW UNIT # 2
EPC SPECIFICATION
NIT DOC. NO. D-51123-LAPPL
45 Of 49
TECHNICAL SPECIFICATION
5. The hoist shall be designed and constructed in accordance with the latest
revision of IS:3938 and shall be suitable for duty class 2.
6. Trolley movement and hoisting shall be effected by using two separate motors.
The motors shall be suitable for 150 starts per hour at 40% CDF.
7. Trolley shall be designed to accommodate a wide range of I beams and shall
be capable of travelling on straight as well as curved monorails with the design
being such to maintain uniform distribution of pressure on the flanges.
8. Motor operated geared trolley shall have two (2) pairs of wheels, one pair of
which shall be driven through motor.
9. Wire rope shall be of pre-formed type, hemp cored, regular lay 6/36
construction with a breaking strength of 160-175 kgf/ sq. mm. Reverse bend of
ropes is not acceptable. Minimum number of falls of rope shall be four (4).
10. All gears and pinions shall be of hardened and tempered steel with machine
cut teeth in metric modules. Surface hardening of steel is not acceptable.
11. All running shafts and wheels shall be fitted with roller bearings with a rated life
not less than 20 years based on equivalent running time as per IS:3938.
12. An electromechanical brake shall provide restraining torque. Brake lining shall be
of asbestos.
13. Cast iron parts, wherever used, shall be of minimum grade 30, IS:210.
14. Hoists shall be selected to have minimum headroom and shall be selected to lift
heaviest piece of equipment. Further, it shall be possible to handle any
equipment without disturbing other equipment.
3.14.03
CONSTRUCTION REQUIREMENT
i. The hoist mechanism shall consist of a grooved rope drum driven by
electric motor through gears. Each end of the rope shall be anchored to
the drum in such a way as the anchorage is readily available for
maintenance. Each rope shall have not more than two (2) full turns of the
drum when the hook is at its lowest position and one (1) spare groove
when the hook is at its highest position.
ii. Rope drum, gear box, block etc. should be fabricated out of weldable
quality steel.
46 Of 49
TECHNICAL SPECIFICATION
iii. Trolley wheels shall be of single flange type in the taper treads. The
wheels shall be mounted on antifriction bearings and shall be easily
removable for repair/replacement.
iv. The load hook shall be swiveling type forged circular shank section and
shall confirm to IS:3815.
v. All gears and bearings shall be lubricated by grease. All lubricating points
shall be grouped together in easily accessible position.
vi. The bottom block shall be of enclosed type and shall have guard against
rope jamming in normal use. It shall have standard forged swivel shank
hook fitted on antifriction thrust bearing. Lock to prevent hook from
rotation and locking arrangement to prevent accidental unlocking shall be
provided. Pulley of the bottom block shall be provided with antifriction
bearings.
vii. All parts requiring replacement/inspection/lubrication shall be accessible
without need for dismantling of other parts/structures.
viii. All components of hoists of identical capacity and duty shall be
interchangeable.
ix. Hoists shall have permanent inscription in English on each side readily
recognizable from floor level stating safe working load.
x. Pendant shall be provided with up/down/forward/reverse travel push
buttons and indicating lamps. Its power supply shall be limited to 24V
AC.
xi. The control panel shall be Pendant type / wall mounted type & easily
approachable from the floor by a person in standing position.
xii. For Inspection / maintenance of hoist components a fixed platform with
ladder shall be provided for each hoist.
47 Of 49
TECHNICAL SPECIFICATION
GENERAL
Functional Requirement
2.0.0
DESIGN
&
CONSTRUCTION
REQUIREMENT
Hoists
Drive
(i) More than 2.0 tonne or
more than
10.0 m lift or hoists coming out-side the
buildings
(ii)
Others
Maximum trolley travel speed for electric
hoists
Maximum Hoisting speed for electric
hoists
Drive Motors
No. of starts for drive motor
Wire Rope
(i)
Type/Construction
2.1.0
2.1.1
2.1.2
2.1.3
2.1.4
2.1.5
2.1.6
To
transfer
equipments
to
maintenance area or outside the
building.
2.1.8
(ii)
Breaking Strength
(iii)
Minimum No. of falls
Bearing
(i)
Type
ii)
Life
Brake
2.1.9
Load Hook
2.1.10
2.2.0
2.2.1
2.2.2
2.2.3
Duty
Monorail location/layout
Cross section
I beam
Distance between C/L of monorail & Maximum 500 mm
C.G. of equipment to be lifted
Power Cables Support
Festoon type arrangement
2.3.0
2.3.1
Manual Hoists
Maximum manual effort for operation.
2.1.7
Roller bearing
20 years
Electro Mechanical type with
asbestos lining.
Swiveling type forged circular
shank section.
Class -2
30 Kg
48 Of 49
TECHNICAL SPECIFICATION
HOIST SCHEDULE
(tentative & shall be as per actual requirements)
S.No.
Location
Track
Minimum
Minimum
Capacity (T)
Quantity
10
Hopper
Type *
Complex
2
JT
15
Crusher house
10
Crusher house
Crusher house
SR
JT
15
JT
Bunker floor
10
49 Of 49