You are on page 1of 34

FINAL REPORT

DESIGN CALCULATION
0,&52&(//32/(0
MICROCELL POLE
24.
GREEN FIELD

THE INFORMATION CONTAINED IN THIS DOCUMENTS ARE THE CONFIDENTIAL


PROPERTY OF PT. DUTA CIPTA PAKARPERKASA. IT MAY NOT THEREFORE BE
REPRODUCUED OR OTHERWISE MADE USE OF OTHER THAN FOR THE PURPOSE
FOR WHICH IT WAS ISSUED BY PT. DUTACIPTA PAKARPERKASA

Design by :

PT. DUTACIPTA PAKARPERKASA


Jl. Panjang Jiwo 58
Surabaya - Indonesia
ENGINEERING DEPT.

CONTENT LIST

DESIGN RESUME

DESIGN CRITERIA

INPUT DATA ( MS TOWER )

Tower Geometry

Tower Loading

OUTPUT DATA ( MS TOWER )

Stress Ratio

Sway & Twist

Support Reaction

OUTLINE DRAWING

APPENDIX

MONOPOLE - 24 M
GREEN FIELD

Design Resume

PT. DUTACIPTA PAKARPERKASA

SUMMARY DESIGN
MONOPOLE TOWER 24 M
DESIGN STRUCTURAL PROJECT

References Document : Design Calculation For MONOPOLE 20 m

Rev.Date 10/03/2016

LOADING DATA
Antenna Load

Wind Load

qty

elev. ( m )

Max. Displacement at wind speed

: 120 Kph
(3 Second Gust)
: 84 Kph

Spec.
Spec.
Spec.

GSM 2G Sector Antenna


MW 600 mm MW Antenna
MW 600 mm MW Antenna

3 pcs
1 pcs
1 pcs

35.00
35.50
34.50

Base level

Spec.
Spec.
Spec.

Working Platform + 2Ring Mounting


Working Platform + 2Ring Mounting
Working Platform

1 pcs
1 pcs
1 pcs

34.50
22.50
10.00

Basic Wind Speed

0m

SUMMARY DESIGN
Max. Stress Ratio

:
LEG

0.709

Max. Ancillary rotation

Max.Sway

Max. Displacement

Max. Support Reaction

Fx
Fy
Fz
Mmax

:
:
:
:

0.0035

<

OK!

<

0.5

degree

OK!

0.426

<

0.5

degree

OK!

167.9

<

H/200

180

mm

OK!

46.210 KN
42.973 KN
131.967 KN
983.760 KNm

NOTE
1. Stress Ratio is a comparison between total stresses occured in members and allowable stresses of each members.
2. Ancillary Rotation is an angular rotation of structure in the horizontal plane.
3. Sway is an angular rotation of structure in the vertical plane.

PT. DUTACIPTA PAKARPERKASA

Design
Check I
Check II

Approved by ;

MONOPOLE - 20 M
GREEN FIELD

Design Criteria

PT. DUTA CIPTA PAKARPERKASA

STRUCTURAL ANALYSIS AND DESIGN


FOR SELF SUPPORTING TOWER
In compliance with the technical specification, the document describes
the minimum criteria for specifying and designing of tower.

I. STANDARD / REFERENCE
a. TIA / EIA - 222 - STANDARD : Structural Standards for Steel
Antenna Towers and Antenna Supporting Structures.
b. AISC-ASD Code ' 89 - American Institute of Steel Construction
c. ACI 318-89 Code - American Concrete Institute
d. Indonesian Loading Code ( PMI 1970 N.I-I8 )

II. MATERIALS SPECIFICATION


a.

b.

c.

d.

e.

f.

g.

Steel Structure
- Structure Type
= Self Supporting Tower
- Steel Shapes & Plates = ASTM A dia.40 / JIS G3101

fy = 245 Mpa

Bolt & Nut


- Splice Bolts

fy = 560 Mpa

= ASTM A - 325 / JIS B1051 - Grade 8.8

Anchor Bolt
- Grade of Anchor = ASTM A - 307

fy = 240 Mpa

First Coating
- Hot Dipped Galv. = ASTM A - 123

80 microns thickness

Concrete
- fc'

= 19 Mpa ( 28 days ) / K-225

Rebars
- Grade of rebars
- Grade of rebars

= BJTP ( dia. 12 mm )
= BJTD ( dia. 13 mm )

Welding Electrodes
- Minimum Grade of Welding Electrode = AWS A5.1 E60XX.

Prepared by : DE-Dept
10/03/2016

fy = 240 Mpa
fy = 390 Mpa

fy = 345 Mpa

PT. DUTA CIPTA PAKARPERKASA

III. LOADINGS
a.

b.

Dead Load
Consist of Weight of Tower structure including antenna, ladder
and appurtenances.
Wind Load
Calculated according to TIA / EIA - 222 - STANDARD : Structural
Standard for Steel Antenna Towers and Antenna Supporting Structures
The basic wind speed is based on peak gust velocity averaged over a short time
Basic wind speed = 120 kph (3 Second Gust)
Where wind force applied to each section of the structure shall be calculated from
the equation :
F = horizontal force applied to a section of the structure ( KN )
qz * GH * [ CF * AE + CA*AA)], but not to exceed 2*qz*GH*AG
qz = Velocity pressure ( Pa )
= .613 Kz V2 for V in m/s
Kz = Exposure Coefficient
[z/10]2/7 for z in meters
1.00 < Kz<2.58
V = basic wind speed for the structure location ( m.s -1)
z = height above average ground level to midpoint of panel of the structure and
appurtenances ( M )
GH = gust response factor
CF = structure force coefficient
e

= (AF+AR)/AG

e = solidity ratio
AF = projected area of flat structural component in one face of the section ( m 2 )
AG = gross area of one tower face ( m 2 )
AR = Projected area ( m2 ) of round structural component in one face of the section
AE = efective projected area of structural component in one face ( m 2 )
= DF AF + DR AR RR

(m2)

( Note : For tubular steel pole structure, AE shall be the actual projected area based on
diameter or overall width. )
RR = .51e2 + .57 RR<1.0
RR = The reduction factor for round structural component
DF = Wind direction factor
1
for square cross section and normal wind direction
1+ 0.75 e for square cross section and + 45 0 wind direction (1.2 max)
DR = Wind direction factor for round structural components
= 1 ; for square cross section and normal wind direction
= 1+ 0.75 e ; for square cross section and + 45 0 wind direction
(1.2 max)
CA = linear or discrete appurtance force coefficient
AA = projected area of a linear appurtance
CA is depended on Aspect ratio
Aspect Ratio = Overall length/width ratio in plane normal to wind direction

Prepared by : DE-Dept
10/03/2016

PT. DUTA CIPTA PAKARPERKASA

Wind Load Calculation method on the antennas is as follow:


Fa = Ca x A x Kz x GH x V2
Fs = Cs x A x Kz x GH x V2
M = Cm x D x A x Kz x GH x V2
Ha = (Fa2+Fs2 )1/2
Mt = Fa x X + Fs x Y + M
L = the distance the antenna's axis to the frame's joints
GH = Gust response factor from 2.3.4
= 0.65+0.6/(h/10) 1/7 for h in meters
A = Outside aperture area of parabolic reflector, grid, or horn antenna
= Plate area of passive reflector ( ft 2 )
D = Outside diameter of parabolic reflector, grid, or horn antenna ( ft )
= Width or length of passive reflector ( ft 2 )
V = basic wind speed ( m.p.h ) from 2.3.3
KZ = Exposure coefficient from 2.3.3 with z equal to the hight
of the origin of the axis system
Kz = Exposure Coefficient
= [z/10]2/7 for z in meters
( lb )
FA = axial force
Fs = side force
( lb )
M = Twisting moment
( ft-lb )
Ca, Cs, Cm are load coeficients contained in tables B1
trough B6 as function of wind angle,... TIA page 62-67
Ha = resultant of FA and FS ( lb )
Mt = Total twisting moment ( ft-lb )
X = The offset of the mounting pipe ( ft )
Y = The distance on the reflector axis from the reflector vertex to
the center of the mounting pipe ( ft )
Wind Load Calculation methode on the parabolic antenna is as follow:
Fa = Ca x A x Kz x GH x V2
Fs = Cs x A x Kz x GH x V2
M = Cm x D x A x Kz x GH x V2
Ha = (Fa2+Fs2 )1/2
Mt = Fa x X + Fs x Y + M
where:
Fa = axial force
( kg )
Fs = side force
( kg )
M = Twisting moment
( kg-m )
Ca = Wind load coeficient
Cs = Wind load coeficient
Cm = Wind load coeficient
V = Wind velocity
( m.p.h )

Prepared by : DE-Dept
10/03/2016

PT. DUTA CIPTA PAKARPERKASA

c.

Antennas Load and Top body part dimension.


Tower Structure considered to be able to support the antennas load as
table bellow :

No.

Description

elevation
m

Qty.

GSM 2G Sectoral Antenna

35.00

3 pcs

MW Ant. 0.6 m ( solid )

35.50

1 pcs

MW Ant. 0.6 m ( solid )

34.50

1 pcs

Working Platform + 2 Mounting Ring

34.50

1 pcs

Working Platform + 2 Mounting Ring

22.50

1 pcs

Working Platform

10.00

1 pcs

IV. LOAD COMBINATION


According to AISC - ASD'89 Standard , only the following load combination shall be
investigated when calculating the maximum member stresses and structure reaction :
COMB 1 = DL
COMB 2 = DL + LL
COMB 3 = DL + LL WL
Where ;
DL : Dead Load
LL : Live Load
WL : Wind Load

V. DESIGN TOLERANCES
The design / analysis tolerances are :
a. Allowable Stress Ratio
b. Slenderness Ratio
:

= 1
Leg
Bracing
Redudant

150
200
250

c. Allowable Twist
= 0.5 degree
d. Allowable Sway
= 0.5 degree
e. Allowable Horizontal Displacement
= H/200 ( H= Tower Height )
f. Verticality
= H/2000 ( H= Tower Height )

Prepared by : DE-Dept
10/04/2010

PT. DUTA CIPTA PAKARPERKASA

VI. ALLOWABLE UNIT STRESS


The unit stresses in the stucture membersdo not aceed the allowable unit stresses
for the materials as specified in the EIA standard EIA - 222
1. Tension
Ft = 0.60 Fy ( Kg/cm2 )
2. Shear
Fv = 0.40 Fy ( Kg/cm2 )
3. Compression
i ) On the gross section of axial loaded compression members when kl/r is less than Cc :

Fa

kl r

1 2 Cc 2 Fy

=
3
kl
r
3
(
)
5
( kl / r )
+

3
8 Cc
8 Cc 3

where

; Cc

( Kg

/ cm

2 2 E
Fy

ii ) On the gross section of axial loaded compression member, when kl/r exceeds
Fa =

12 2 E
( Kg / cm
Fy

4) Bending
Tension and compression on extreme fibers :
Fb = 0.66 Fy (Kg/cm2)
5) Tension on Bolts
Fv = 0.60 Fy ( kg/cm2 )
6) Shear on Bolts
Fv = 0.30 Fy ( kg/cm2 )
7) Bearing on Bolts
Fp = 1.20 Fv ( kg/cm2)

Prepared by : DE-Dept
10/04/2010

MONOPOLE - 24 M
GREEN FIELD

Input Data

MONOPOLE - 24 M
GREEN FIELD

Tower Geometry

Page 1 of 1
10 Apr 2010
8:45 AM

Civil Engineering

TITL1
TITL2

TOWER BERSAMA
MONOPOLE .36M

UNITS
1
PROFILE
FACES 1
WBASE
1.100
RLBAS
0.000
PANEL
1 HT
3.0000 TW
FACE SH1 LEG
1 R1 47

0.4450

PANEL
2 HT
3.0000 TW
FACE SH1 LEG
7 R1 47

0.5050

PANEL 3 HT
3.0000 TW
FACE SH1 LEG 13 R1 47

0.5660

PANEL 4 HT
3.0000 TW
FACE SH1 LEG 18 R1 47

0.6275

PANEL 5 HT
3.0000 TW
FACE SH1 LEG 22 R1 47

0.6875

PANEL 6 HT
3.0000 TW
FACE SH1 LEG 26 R1 47

0.7475

PANEL 7 HT
3.0000 TW
FACE SH1 LEG 30 R1 47

0.8100

PANEL 8 HT
3.0000 TW
FACE SH1 LEG 33 R1 47

0.8700

PANEL 9 HT
3.0000 TW
FACE SH1 LEG 36 R1 47

0.9300

PANEL 10 HT
3.0000 TW
FACE SH1 LEG 39 R1 47

0.9900

PANEL 11 HT
3.0000 TW
FACE SH1 LEG 42 R1 47

1.0550

PANEL 12 HT
3.0000 TW
FACE SH1 LEG 44 R1 47

1.1000

PANEL 13 HT
0.0000 TW
1.1000
FACE SH1 LEG 46 R1 47
END
SECTIONS
LIB MONOPOLE3
1 PG1.445x6
FY
245.00
2 PG2.455x6
FY
245.00
3 PG3.465x6
FY
245.00
4 PG4.475x6
FY
245.00
5 PG5.485x6
FY
245.00
6 PG6.495x6
FY
245.00
7 PG7.505x6
FY
245.00
8 PG8.515x6
FY
245.00
9 PG9.525x6
FY
245.00
10 PG10.535x6
FY
245.00
11 PG11.545x6
FY
245.00
12 PG12.555x6
FY
245.00
13 PG13.566x6
FY
245.00
14 PG14.578x6
FY
245.00
15 PG15.590x6
FY
245.00
16 PG16.602x6
FY
245.00
17 PG17.614x6
FY
245.00
18 PG18.628x6
FY
245.00
19 PG19.643x6
FY
245.00
20 PG20.658x6
FY
245.00
21 PG21.673x6
FY
245.00
22 PG22.688x6
FY
245.00
23 PG23.703x6
FY
245.00
24 PG24.718x6
FY
245.00
25 PG25.733x6
FY
245.00
26 PG26.748x6
FY
245.00
27 PG27.763x6
FY
245.00
28 PG28.778x6
FY
245.00
29 PG29.793x6
FY
245.00
30 PG30.810x8
FY
245.00

31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
END

PG31.830x8
PG32.850x8
PG33.870x8
PG34.890x8
PG35.910x8
PG36.930x8
PG37.950x8
PG38.970x8
PG39.990x8
PG40.1010x8
PG41.1030x8
PG42.1055x8
PG43.1085x8
PG44.1100x8
PG45.1100x8
PG46.1100x8
DUMMY

FY
FY
FY
FY
FY
FY
FY
FY
FY
FY
FY
FY
FY
FY
FY
FY
FY

245.00
245.00
245.00
245.00
245.00
245.00
245.00
245.00
245.00
245.00
245.00
245.00
245.00
245.00
245.00
245.00
245.00

SUPPORT
COORD 0.0 0.0 0.0 FIXED
END
EOF

Civil Engineering
Job: MONOPOLE 20M
TOWER BERSAMA
MONOPOLE 20M

10 Mar 2016
09:06 AM

47
47
47
1
47
47
47
7
47
47
47
13
47
47
47
18
47
47
47
22
47
47
47
26
47
47
47
30
47
47
47
33
4747
47
36
4747
47
39
4747
47
42
4747
47
44
Z
Y
X
theta: 195 phi: 15

4747
47

Sections:
1 PG1.445X6 Y
7 PG7.505X6 Y
13 PG13.566X6 Y
18 PG18.628X6 Y
22 PG22.688X6 Y
26 PG26.748X6 Y
30 PG30.810X8 Y
33 PG33.870X8 Y
36 PG36.930X8 Y
39 PG39.990X8 Y
42 PG42.1055X8 Y
44 PG44.1100X8 Y
47 DUMMY Y

MICROCELL POLE - 20M


GREEN FIELD

Tower Loading

Page 1 of 3
10 Mar 2016
9:08 AM

Civil Engineering

$ from FILE TWRSTD.TWR


$ prototype TWR file for square tower. Edit to your requirements
$
$
$
$

STATION
HEIGHT
NGR SP
MAP No

$ STRUCTURE
$
$
$
$
$
$
$
$

TYPE:MANUFACTURERS:ANCILLARIES Drawings
Amendments
CAD REF
STRUCTURAL Drawings:-

PARAMETERS
ANGN
CODE
ICE
ALTOP
PSF-V
PSF-M
VB
OVERLAP

90.0
EIA222
RO 0.0
0
1.00
1.00
27.78
1

RW 0.0

$
$
$
$
$
$
$
$

Angle Anti-clockwise from X axis to North


Code TIA/EIA222-F
For icing
SITE + TOWER HEIGHT for icing
Partial safety factor for wind speed, BS8100
Partial safety factor for Material strength, BS8100
Basic Wind Speed 120 Kph (Fastest Mile)
Allow for the overlap of members

END
LOADS
CASE
DL

100 Weight of tower plus ancillaries

CASE 200 wind at


0 to X axis
WL ANGLX
0.0 NOICE
CASE 220 wind at
45 to X axis
WL ANGLX 45.0 NOICE
CASE 240 wind at
90 to X axis
WL ANGLX 90.0 NOICE
CASE 260 wind at 135 to X axis
WL ANGLX 135.0 NOICE
CASE 280 wind at 180 to X axis
WL ANGLX 180.0 NOICE
CASE 300 wind at 225 to X axis
WL ANGLX 225.0 NOICE
CASE 320 wind at 270 to X axis
WL ANGLX 270.0 NOICE
CASE 340 wind at 315 to X axis
WL ANGLX 315.0 NOICE
CASE 500 Max. tower weight
COMBIN 100 1.000
CASE 520 TENSION: wind at
COMBIN 100 1.000
COMBIN 200 1.000

0 to X axis

CASE 540 COMPRES: wind at


COMBIN 100 1.000
COMBIN 200 1.000

0 to X axis

CASE 560 TENSION: wind at


COMBIN 100 1.000
COMBIN 220 1.000

45 to X axis

CASE 580 COMPRES: wind at


COMBIN 100 1.000
COMBIN 220 1.000

45 to X axis

Page 2 of 3
10 Mar 2016
9:08 AM

Civil Engineering

CASE 600 TENSION: wind at


COMBIN 100 1.000
COMBIN 240 1.000

90 to X axis

CASE 620 COMPRES: wind at


COMBIN 100 1.000
COMBIN 240 1.000

90 to X axis

CASE 640 TENSION: wind at


COMBIN 100 1.000
COMBIN 260 1.000

135 to X axis

CASE 660 COMPRES: wind at


COMBIN 100 1.000
COMBIN 260 1.000

135 to X axis

CASE 680 TENSION: wind at


COMBIN 100 1.000
COMBIN 280 1.000

180 to X axis

CASE 700 COMPRES: wind at


COMBIN 100 1.000
COMBIN 280 1.000

180 to X axis

CASE 720 TENSION: wind at


COMBIN 100 1.000
COMBIN 300 1.000

225 to X axis

CASE 740 COMPRES: wind at


COMBIN 100 1.000
COMBIN 300 1.000

225 to X axis

CASE 760 TENSION: wind at


COMBIN 100 1.000
COMBIN 320 1.000

270 to X axis

CASE 780 COMPRES: wind at


COMBIN 100 1.000
COMBIN 320 1.000

270 to X axis

CASE 800 TENSION: wind at


COMBIN 100 1.000
COMBIN 340 1.000

315 to X axis

CASE 820 COMPRES: wind at


COMBIN 100 1.000
COMBIN 340 1.000

315 to X axis

END
ANCILLARIES
LINEAR LIB L:BJA_Lin
LADDER
CTRAY
FEEDER-1
FEEDER-2

XB 0.00
XB 0.30
XB 0.35
XB -0.35

YB
YB
YB
YB

-1.00
-0.80
-0.80
-0.80

ZB
ZB
ZB
ZB

0.00
0.00
0.00
0.00

XT 0.00
XT 0.25
XT 0.30
XT -0.30

YT
YT
YT
YT

-0.50
-0.35
-0.35
-0.35

ZT
ZT
ZT
ZT

35.0
35.0
35.0
35.0

LIB
LIB
LIB
LIB

LD-POLE
CTPOLE
FDRPOLE_3C
FDRPOLE_3C

LARGE LIB L:BJA_Anc


SWANN-P1
SWANN-P2
SWANN-P3
SWANN-P4
SWANN-P5

XA
XA
XA
XA
XA

0.0
0.0
0.0
0.0
0.0

YA
YA
YA
YA
YA

0.0
0.0
0.0
0.0
0.0

ZA
ZA
ZA
ZA
ZA

35.500
34.500
25.000
22.500
10.000

lib
lib
lib
lib
lib

SWANN-P3
SWANN-C1/2
SWANN-P4
SWANN-C1/2
SWANN-C1/2

ANG
ANG
ANG
ANG
ANG

180
180
180
180
180

$ MICROWAVE Antennas D 0.6 meter


MW1-0.6
MW2-0.6

XA
XA

-2.00
-2.00

YA
YA

0.00
0.00

ZA
ZA

35.50
34.50

LIB SH1PR-2 ANG


LIB SH1PR-2 ANG

270
270

AMASS 100
AMASS 100

$ GSM 2.5M
GSM-1
GSM-2
GSM-3

XA
XA
XA

0.00
2.00
0.00

YA
YA
YA

2.00
0.00
-2.00

ZA 35.00
ZA 35.00
ZA 35.00

LIB A0305 ANG


LIB A0305 ANG
LIB A0305 ANG

0
90
180

AMASS 100
AMASS 100
AMASS 100

FACT
FACT
FACT
FACT

1
1
1
1

ANG
ANG
ANG
ANG

90
0
0
0

Civil Engineering

END
END

Page 3 of 3
10 Mar 2016
9:08 AM

Civil Engineering
Job: MONOPOLE 20M
TOWER BERSAMA
MONOPOLE 20M

10 Mar 2016
08:46 AM

MW1-0.6
SWANN-P1 GSM-3
SWANN-P2 MW2-0.6 GSM-1 GSM-2

SWANN-P3
SWANN-P4

SWANN-P5

Civil Engineering
Job: MONOPOLE 20M
TOWER BERSAMA
MONOPOLE 20M

Z
Y

theta: 105 phi: 15

10 Mar 2016
08:46 AM

MICROCELL POLE - 20 M
GREEN FIELD

Output Data

MICROCELL POLE - 20 M
GREEN FIELD

Stress Ratio

Page 1 of 1
10 Mar 2016
8:45 AM

Civil Engineering

MSTOWER V6 Dev Member checking to EIA-222-F

.
TOWER BERSAMA
MONOPOLE .36M
-- L O A D
Case
Y/N
100
N
200
N
220
N
240
N
260
N
280
N
300
N
320
N
340
N
500
Y
520
Y
540
Y
560
Y
580
Y
600
Y
620
Y
640
Y
660
Y
680
Y
700
Y
720
Y
740
Y
760
Y
780
Y
800
Y
820
Y

C A S E S -Title
WEIGHT OF TOWER PLUS ANCILLARIES
WIND AT
0 TO X AXIS
WIND AT
45 TO X AXIS
WIND AT
90 TO X AXIS
WIND AT 135 TO X AXIS
WIND AT 180 TO X AXIS
WIND AT 225 TO X AXIS
WIND AT 270 TO X AXIS
WIND AT 315 TO X AXIS
MAX. TOWER WEIGHT
TENSION: WIND AT
0 TO X AXIS
COMPRES: WIND AT
0 TO X AXIS
TENSION: WIND AT
45 TO X AXIS
COMPRES: WIND AT
45 TO X AXIS
TENSION: WIND AT
90 TO X AXIS
COMPRES: WIND AT
90 TO X AXIS
TENSION: WIND AT 135 TO X AXIS
COMPRES: WIND AT 135 TO X AXIS
TENSION: WIND AT 180 TO X AXIS
COMPRES: WIND AT 180 TO X AXIS
TENSION: WIND AT 225 TO X AXIS
COMPRES: WIND AT 225 TO X AXIS
TENSION: WIND AT 270 TO X AXIS
COMPRES: WIND AT 270 TO X AXIS
TENSION: WIND AT 315 TO X AXIS
COMPRES: WIND AT 315 TO X AXIS

Y = Cases to be checked
N = Not Used
Report Units:
Dims., lengths, areas ... mm, mm2
Forces ..................... kN
Moments, Torques ........... kNm
Stresses ..............N/mm2 (MPa)
Allowable stresses to EIA-222-F. Overstress factor for WL:
Safety factor for guys:
2.000
Symbols:
fy = yield stress
nb = no. bolts in end connection.
C
= Section 5.7 sub-clause used for KL/r.
KL/r= Section 5.7.4 slenderness ratio. x/y/v=buckling axis.
P
= Axial force in member, kN. c=compression
f
= Axial stress in member, MPa.
F
= Allowable stress, MPa.
*
= Stress ratio > 1.0
#
= Exceeds code slenderness ratio

1.330

NB: The design approach of EIA-222-F is based on working stress methods.


Shaft Members - Cross-section: 12 sided polygon
Memb
1
101
201
301
401
501
601
701
801
901
1001
1101

Ht
D
33.0 445.0
30.0 505.0
27.0 566.0
24.0 627.5
21.0 687.5
18.0 747.5
15.0 810.0
12.0 870.0
9.0 930.0
6.0 990.0
3.0 1055.0
0.0 1100.0

t
6.0
6.0
6.0
6.0
6.0
6.0
8.0
8.0
8.0
8.0
8.0
8.0

fy
245.0
245.0
245.0
245.0
245.0
245.0
245.0
245.0
245.0
245.0
245.0
245.0

LC
540
540
540
540
540
540
700
700
700
700
700
700

P
10
13
17
21
31
35
41
48
54
64
71
79

Mx
0
0
0
0
0
0
0
0
0
0
0
0

My
18
46
84
129
184
248
319
397
482
580
682
791

Mr
18
46
84
129
184
248
319
397
482
580
682
791

T
0
0
0
0
0
0
0
0
0
0
0
0

fa
1.2
1.4
1.6
1.8
2.3
2.5
2.0
2.1
2.3
2.5
2.6
2.8

fb
18.7
38.1
54.5
68.1
81.1
92.2
76.1
82.0
86.8
92.0
95.2
101.4

Fa
147.0
147.0
147.0
147.0
147.0
147.0
147.0
147.0
147.0
147.0
147.0
147.0

Fb
147.0
147.0
147.0
147.0
147.0
147.0
147.0
147.0
147.0
147.0
147.0
147.0

0
0
0
0
0
0
0
0
0
0
0
0

ratio
0.135
0.268
0.382
0.475
0.568
0.644
0.531
0.572
0.606
0.643
0.665
0.709

Civil Engineering
Job: MONOPOLE 20M
TOWER BERSAMA
MONOPOLE 20M
Design Ratios - % of Code Capacity:
<= 50
<= 95
<= 100
<= 105
<= 110
> 110

Z
Y

theta: 105 phi: 15

10 Mar 2016
08:46 AM

MICROCELL POLE - 20 M
GREEN FIELD

Sway & Twist

Page 1 of 3
10 Mar 2016
9:02 AM

Civil Engineering

ANCILLARY ROTATIONS
-- L O A D
Case
Y/N
100
N
200
N
220
N
240
N
260
N
280
N
300
N
320
N
340
N
500
Y
520
Y
540
Y
560
Y
580
Y
600
Y
620
Y
640
Y
660
Y
680
Y
700
Y
720
Y
740
Y
760
Y
780
Y
800
Y
820
Y

C A S E S -Title
WEIGHT OF TOWER PLUS ANCILLARIES
WIND AT
0 TO X AXIS
WIND AT
45 TO X AXIS
WIND AT
90 TO X AXIS
WIND AT 135 TO X AXIS
WIND AT 180 TO X AXIS
WIND AT 225 TO X AXIS
WIND AT 270 TO X AXIS
WIND AT 315 TO X AXIS
MAX. TOWER WEIGHT
TENSION: WIND AT
0 TO X AXIS
COMPRES: WIND AT
0 TO X AXIS
TENSION: WIND AT
45 TO X AXIS
COMPRES: WIND AT
45 TO X AXIS
TENSION: WIND AT
90 TO X AXIS
COMPRES: WIND AT
90 TO X AXIS
TENSION: WIND AT 135 TO X AXIS
COMPRES: WIND AT 135 TO X AXIS
TENSION: WIND AT 180 TO X AXIS
COMPRES: WIND AT 180 TO X AXIS
TENSION: WIND AT 225 TO X AXIS
COMPRES: WIND AT 225 TO X AXIS
TENSION: WIND AT 270 TO X AXIS
COMPRES: WIND AT 270 TO X AXIS
TENSION: WIND AT 315 TO X AXIS
COMPRES: WIND AT 315 TO X AXIS

Y = Cases to be checked
N = Not Used
ENVELOPE OF TOWER ROTATIONS (Degrees)
Pt Height
LC
X-Rot
LC
Y_Rot

LC

ROTATIONS OF ANCILLARY AXES (Degrees)


Ancillary
Height Bearing
Case
SWANN-P1
35.500 180.000
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
800
820
SWANN-P2
34.500 180.000
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
800
820
SWANN-P3
25.000 180.000
500
520
540
560
580
600

Z-Rot
Rot-x
0.0317
0.4264
0.4264
0.3092
0.3092
0.0345
0.0345
0.2516
0.2516
0.3695
0.3695
0.2516
0.2516
0.0345
0.0345
0.3092
0.3092
0.0317
0.4264
0.4264
0.3092
0.3092
0.0345
0.0345
0.2516
0.2516
0.3695
0.3695
0.2516
0.2516
0.0345
0.0345
0.3092
0.3092
0.0087
0.3096
0.3096
0.2194
0.2194
0.0106

Rot-y
0.0000
0.0000
0.0000
0.2626
0.2626
0.3696
0.3696
0.2631
0.2631
0.0000
0.0000
0.2631
0.2631
0.3696
0.3696
0.2626
0.2626
0.0000
0.0000
0.0000
0.2626
0.2626
0.3696
0.3696
0.2631
0.2631
0.0000
0.0000
0.2631
0.2631
0.3696
0.3696
0.2626
0.2626
0.0000
0.0000
0.0000
0.2009
0.2009
0.2815

Rot-z
0.0000
0.0000
0.0000
0.0033
0.0033
0.0031
0.0031
0.0035
0.0035
0.0000
0.0000
0.0035
0.0035
0.0031
0.0031
0.0033
0.0033
0.0000
0.0000
0.0000
0.0033
0.0033
0.0031
0.0031
0.0035
0.0035
0.0000
0.0000
0.0035
0.0035
0.0031
0.0031
0.0033
0.0033
0.0000
0.0000
0.0000
0.0009
0.0009
0.0008

Page 2 of 3
10 Mar 2016
9:02 AM

Civil Engineering

SWANN-P4

22.500

180.000

SWANN-P5

10.000

180.000

MW1-0.6

35.500

270.000

MW2-0.6

34.500

270.000

GSM-1

35.000

0.000

620
640
660
680
700
720
740
760
780
800
820
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
800
820
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
800
820
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
800
820
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
800
820
500

0.0106
0.2058
0.2058
0.2965
0.2965
0.2058
0.2058
0.0106
0.0106
0.2194
0.2194
0.0087
0.3096
0.3096
0.2194
0.2194
0.0106
0.0106
0.2058
0.2058
0.2965
0.2965
0.2058
0.2058
0.0106
0.0106
0.2194
0.2194
0.0016
0.1086
0.1086
0.0761
0.0761
0.0021
0.0021
0.0741
0.0741
0.1067
0.1067
0.0741
0.0741
0.0021
0.0021
0.0761
0.0761
0.0000
0.0000
0.0000
0.2626
0.2626
0.3696
0.3696
0.2631
0.2631
0.0000
0.0000
0.2631
0.2631
0.3696
0.3696
0.2626
0.2626
0.0000
0.0000
0.0000
0.2626
0.2626
0.3696
0.3696
0.2631
0.2631
0.0000
0.0000
0.2631
0.2631
0.3696
0.3696
0.2626
0.2626
0.0317

0.2815
0.2012
0.2012
0.0000
0.0000
0.2012
0.2012
0.2815
0.2815
0.2009
0.2009
0.0000
0.0000
0.0000
0.2009
0.2009
0.2815
0.2815
0.2012
0.2012
0.0000
0.0000
0.2012
0.2012
0.2815
0.2815
0.2009
0.2009
0.0000
0.0000
0.0000
0.0718
0.0718
0.1001
0.1001
0.0719
0.0719
0.0000
0.0000
0.0719
0.0719
0.1001
0.1001
0.0718
0.0718
0.0317
0.4264
0.4264
0.3092
0.3092
0.0345
0.0345
0.2516
0.2516
0.3695
0.3695
0.2516
0.2516
0.0345
0.0345
0.3092
0.3092
0.0317
0.4264
0.4264
0.3092
0.3092
0.0345
0.0345
0.2516
0.2516
0.3695
0.3695
0.2516
0.2516
0.0345
0.0345
0.3092
0.3092
0.0000

0.0008
0.0009
0.0009
0.0000
0.0000
0.0009
0.0009
0.0008
0.0008
0.0009
0.0009
0.0000
0.0000
0.0000
0.0009
0.0009
0.0008
0.0008
0.0009
0.0009
0.0000
0.0000
0.0009
0.0009
0.0008
0.0008
0.0009
0.0009
0.0000
0.0000
0.0000
0.0002
0.0002
0.0002
0.0002
0.0002
0.0002
0.0000
0.0000
0.0002
0.0002
0.0002
0.0002
0.0002
0.0002
0.0000
0.0000
0.0000
0.0033
0.0033
0.0031
0.0031
0.0035
0.0035
0.0000
0.0000
0.0035
0.0035
0.0031
0.0031
0.0033
0.0033
0.0000
0.0000
0.0000
0.0033
0.0033
0.0031
0.0031
0.0035
0.0035
0.0000
0.0000
0.0035
0.0035
0.0031
0.0031
0.0033
0.0033
0.0000

Page 3 of 3
10 Mar 2016
9:02 AM

Civil Engineering

GSM-2

35.000

90.000

GSM-3

35.000

180.000

520
540
560
580
600
620
640
660
680
700
720
740
760
780
800
820
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
800
820
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
800
820

0.4264
0.4264
0.3092
0.3092
0.0345
0.0345
0.2516
0.2516
0.3695
0.3695
0.2516
0.2516
0.0345
0.0345
0.3092
0.3092
0.0000
0.0000
0.0000
0.2626
0.2626
0.3696
0.3696
0.2631
0.2631
0.0000
0.0000
0.2631
0.2631
0.3696
0.3696
0.2626
0.2626
0.0317
0.4264
0.4264
0.3092
0.3092
0.0345
0.0345
0.2516
0.2516
0.3695
0.3695
0.2516
0.2516
0.0345
0.0345
0.3092
0.3092

0.0000
0.0000
0.2626
0.2626
0.3696
0.3696
0.2631
0.2631
0.0000
0.0000
0.2631
0.2631
0.3696
0.3696
0.2626
0.2626
0.0317
0.4264
0.4264
0.3092
0.3092
0.0345
0.0345
0.2516
0.2516
0.3695
0.3695
0.2516
0.2516
0.0345
0.0345
0.3092
0.3092
0.0000
0.0000
0.0000
0.2626
0.2626
0.3696
0.3696
0.2631
0.2631
0.0000
0.0000
0.2631
0.2631
0.3696
0.3696
0.2626
0.2626

0.0000
0.0000
0.0033
0.0033
0.0031
0.0031
0.0035
0.0035
0.0000
0.0000
0.0035
0.0035
0.0031
0.0031
0.0033
0.0033
0.0000
0.0000
0.0000
0.0033
0.0033
0.0031
0.0031
0.0035
0.0035
0.0000
0.0000
0.0035
0.0035
0.0031
0.0031
0.0033
0.0033
0.0000
0.0000
0.0000
0.0033
0.0033
0.0031
0.0031
0.0035
0.0035
0.0000
0.0000
0.0035
0.0035
0.0031
0.0031
0.0033
0.0033

MICROCELL POLE - 20 M
GREEN FIELD

Support Reaction

Civil Engineering
Job: MONOPOLE 20M
TOWER BERSAMA
MONOPOLE 20M

10 Mar 2016
09:25 AM

1103
1104

1002
1105

1203
1204

1102
1205

Z
Y

theta: 105 phi: 15

Page 1 of 4
10 Mar 2016
9:56 AM

Civil Engineering
Job: MONOPOLE 20M
TOWER BERSAMA
MONOPOLE 20M
I N P U T / A N A L Y S I S
Job:

MICROCELM.

Title:

TOWER BERSAMA
MONOPOLE .36M
Space frame
10-Mar-16
09:55:28

Type:
Date:
Time:

R E P O R T

Nodes .............................
Members ...........................
Spring supports ...................
Sections ..........................
Materials .........................
Primary load cases ................
Combination load cases ............
Analysis:

52
51
0
13
1
9
17

Linear elastic

PLATE DIA. 40cm NOT STABLE

THIKNESS PIPE NOT STABLE

C O N D I T I O N

N U M B E R

Maximum condition number: 3.071E+02 at node: 1 DOFN: 1


S U P P O R T
CASE
Node

R E A C T I O N S

500: MAX. TOWER WEIGHT

1102
1203
1204
1205

Force-X
kN
0.000
0.000
0.000
0.000

Force-Y
kN
0.000
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
0.000
0.000
0.000
0.000

Moment-Y
kNm
3.646
0.000
0.000
0.000

SUM:

0.000

0.000

131.967

(all nodes)

Moment-Z
kNm
0.000
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

520: TENSION: WIND AT

0 TO X AXIS

1102
1203
1204
1205

Force-X
kN
45.918
0.000
0.000
0.000

Force-Y
kN
0.000
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
0.000
0.000
0.000
0.000

Moment-Y
kNm
980.846
0.000
0.000
0.000

SUM:

45.918

0.000

131.967

(all nodes)

Moment-Z
kNm
0.000
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

540: COMPRES: WIND AT

0 TO X AXIS

1102
1203
1204
1205

Force-X
kN
45.918
0.000
0.000
0.000

Force-Y
kN
0.000
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
0.000
0.000
0.000
0.000

Moment-Y
kNm
980.846
0.000
0.000
0.000

SUM:

45.918

0.000

131.967

(all nodes)

Moment-Z
kNm
0.000
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

560: TENSION: WIND AT

45 TO X AXIS

1102
1203
1204
1205

Force-X
kN
31.749
0.000
0.000
0.000

Force-Y
kN
31.074
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
-656.117
0.000
0.000
0.000

Moment-Y
kNm
683.402
0.000
0.000
0.000

SUM:

31.749

31.074

131.967

(all nodes)

Moment-Z
kNm
0.951
0.000
0.000
0.000

Civil Engineering
Job: MONOPOLE 20M
TOWER BERSAMA
MONOPOLE 20M

Page 2 of 4
10 Mar 2016
9:56 AM

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

580: COMPRES: WIND AT

45 TO X AXIS

1102
1203
1204
1205

Force-X
kN
31.749
0.000
0.000
0.000

Force-Y
kN
31.074
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
-656.117
0.000
0.000
0.000

Moment-Y
kNm
683.402
0.000
0.000
0.000

SUM:

31.749

31.074

131.967

(all nodes)

Moment-Z
kNm
0.951
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

600: TENSION: WIND AT

90 TO X AXIS

1102
1203
1204
1205

Force-X
kN
0.129
0.000
0.000
0.000

Force-Y
kN
42.973
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
-913.062
0.000
0.000
0.000

Moment-Y
kNm
8.149
0.000
0.000
0.000

SUM:

0.129

42.973

131.967

(all nodes)

Moment-Z
kNm
0.875
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

620: COMPRES: WIND AT

90 TO X AXIS

1102
1203
1204
1205

Force-X
kN
0.129
0.000
0.000
0.000

Force-Y
kN
42.973
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
-913.062
0.000
0.000
0.000

Moment-Y
kNm
8.149
0.000
0.000
0.000

SUM:

0.129

42.973

131.967

(all nodes)

Moment-Z
kNm
0.875
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

640: TENSION: WIND AT

135 TO X AXIS

1102
1203
1204
1205

Force-X
kN
-32.006
0.000
0.000
0.000

Force-Y
kN
31.095
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
-656.866
0.000
0.000
0.000

Moment-Y
kNm
-685.114
0.000
0.000
0.000

SUM:

-32.006

31.095

131.967

(all nodes)

Moment-Z
kNm
0.991
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

660: COMPRES: WIND AT

135 TO X AXIS

1102
1203
1204
1205

Force-X
kN
-32.006
0.000
0.000
0.000

Force-Y
kN
31.095
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
-656.866
0.000
0.000
0.000

Moment-Y
kNm
-685.114
0.000
0.000
0.000

SUM:

-32.006

31.095

131.967

(all nodes)

Moment-Z
kNm
0.991
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node
1102
1203
1204
1205

R E A C T I O N S

680: TENSION: WIND AT


Force-X
kN
-46.210
0.000
0.000
0.000

Force-Y
kN
0.000
0.000
0.000
0.000

180 TO X AXIS

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
0.000
0.000
0.000
0.000

Moment-Y
kNm
-983.760
0.000
0.000
0.000

Moment-Z
kNm
0.000
0.000
0.000
0.000

Civil Engineering
Job: MONOPOLE 20M
TOWER BERSAMA
MONOPOLE 20M
SUM:

-46.210

Page 3 of 4 10
Mar 2016
9:56 AM
0.000

131.967

(all nodes)

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

700: COMPRES: WIND AT

180 TO X AXIS

1102
1203
1204
1205

Force-X
kN
-46.210
0.000
0.000
0.000

Force-Y
kN
0.000
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
0.000
0.000
0.000
0.000

Moment-Y
kNm
-983.760
0.000
0.000
0.000

SUM:

-46.210

0.000

131.967

(all nodes)

Moment-Z
kNm
0.000
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

720: TENSION: WIND AT

225 TO X AXIS

1102
1203
1204
1205

Force-X
kN
-32.006
0.000
0.000
0.000

Force-Y
kN
-31.095
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
656.868
0.000
0.000
0.000

Moment-Y
kNm
-685.115
0.000
0.000
0.000

SUM:

-32.006

-31.095

131.967

(all nodes)

Moment-Z
kNm
-0.991
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

740: COMPRES: WIND AT

225 TO X AXIS

1102
1203
1204
1205

Force-X
kN
-32.006
0.000
0.000
0.000

Force-Y
kN
-31.095
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
656.868
0.000
0.000
0.000

Moment-Y
kNm
-685.115
0.000
0.000
0.000

SUM:

-32.006

-31.095

131.967

(all nodes)

Moment-Z
kNm
-0.991
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

760: TENSION: WIND AT

270 TO X AXIS

1102
1203
1204
1205

Force-X
kN
0.129
0.000
0.000
0.000

Force-Y
kN
-42.973
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
913.062
0.000
0.000
0.000

Moment-Y
kNm
8.149
0.000
0.000
0.000

SUM:

0.129

-42.973

131.967

(all nodes)

Moment-Z
kNm
-0.875
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

780: COMPRES: WIND AT

270 TO X AXIS

1102
1203
1204
1205

Force-X
kN
0.129
0.000
0.000
0.000

Force-Y
kN
-42.973
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
913.062
0.000
0.000
0.000

Moment-Y
kNm
8.149
0.000
0.000
0.000

SUM:

0.129

-42.973

131.967

(all nodes)

Moment-Z
kNm
-0.875
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node
1102
1203
1204

R E A C T I O N S

800: TENSION: WIND AT


Force-X
kN
31.749
0.000
0.000

Force-Y
kN
-31.074
0.000
0.000

315 TO X AXIS

Force-Z
kN
131.967
0.000
0.000

Moment-X
kNm
656.116
0.000
0.000

Moment-Y
kNm
683.401
0.000
0.000

Moment-Z
kNm
-0.951
0.000
0.000

Civil Engineering
Job: MONOPOLE 20M
TOWER BERSAMA
MONOPOLE 20M

Page 3 of 4
10 Mar 2016
9:56 AM

1205

0.000

0.000

0.000

SUM:

31.749

-31.074

131.967

0.000

0.000

0.000

(all nodes)

(Reactions act on structure in positive global axis directions.)


S U P P O R T
CASE
Node

R E A C T I O N S

820: COMPRES: WIND AT

315 TO X AXIS

1102
1203
1204
1205

Force-X
kN
31.749
0.000
0.000
0.000

Force-Y
kN
-31.074
0.000
0.000
0.000

Force-Z
kN
131.967
0.000
0.000
0.000

Moment-X
kNm
656.116
0.000
0.000
0.000

Moment-Y
kNm
683.401
0.000
0.000
0.000

SUM:

31.749

-31.074

131.967

(all nodes)

Moment-Z
kNm
-0.951
0.000
0.000
0.000

(Reactions act on structure in positive global axis directions.)

You might also like