You are on page 1of 28

Motorola Horizon macro BTS

The Motorola Horizon macro BTS is a BTS model manufactured by Motorola in the late
1990ies.
It can support up to 6 TRX, typically in a configuration of 3 sectors.
There is currently no support for it in OpenBSC, but we are working on it.

Hardware

CTU
The up to 6 CTU modules are the individual transceivers (TRX) of the BTS cabinet.
They plug into the SURF RF backplane and have a front-accessible DB9 serial port, as well
as a SMA connector for the TX PA output.
This TX PA output is normally wired using a ~10cm semi-rigid SMA cable to the TX input
port of a combiner/duplexer.

The CTU is of course fully shielded. But if you remove the shielding cover, it looks like this:

You can see

two diversity receivers in the top left part

digital section in the top right part

transmit section (exciter) in the center

RF power amplifier in the bottom right part

digital part
The CTU digital part has the following connections

backplane connector for


o

power supply (27V DC)

two redundand 2048 Mbps TDM links with MCUF, manchester-encoded, 32


timeslots

three coaxial backplane connectors with SURF


o

Rx side A (diversity)

Rx side B (diversity)

Rx loopback (for transmitting into Rx path, loopback testing)

The CTU digital part consists of three main processors:

RSS (Radio Subsystem)


o

communicates with MCUF via dedicated 64kbps timeslots in TDM link

communicates via dual-ported ram with CCCP

Flash EEPROM for boot loader and 8 MByte DRAM

EQCP (Equalizer and Control Processor)


o

DSP for radio control and channel equalization

alarm management

downlink burst building and modulator control

tx power control

synthesizer channel control

rf frequency hopping

receiver front-end and remote tune combiner control

uplink synchronziation and equalization

diversity receiver control

automatic gain control

receiver signal sthrength calculation

CCCP (Channel Coder Control Processor)


o

DSP for channel coding, data routing and baseband hopping

uplink channel decoding

downlink channel encoding

A5 encryption

baseband frequency hopping

TRAU frame collection and synchronization

The CTU has a three serial consoles routed to the same DB-9 plug. We describe it
in Motorola_Horizon_macro/CTU_Console

Combiner
The combiner / duplexer combines the TX signal of two CTU and duplexes it with the Rx
path in order to be able to have two TRX attached to one antenna

MCUF
The MCUF is a full-size digital board and contains the BTS controller

NIU

The NIU is a E1 interface card for up to two E1 lines. Multiple NIU boards can be plugged
into the rack

BPSM
The BPSM is a small power supply for the NIU, MCUF and other digital boards

ALARMS
The ALARMS board is monitoring FAN and other alarms in the cabinet.

A-bis interface
The A-bis interface is via classic E1 lines. The Horizon indoor cabinet supports up to 6 E1
ports.
Each NIU module serves 1 or 2 E1 ports.
The E1 ports are physically routed to the BIB (Balanced Interface Board) module on top of
the cabinet.
The pinout of the 37pin D-Sub connector on top of the BIB board has been reversed as:
Pin

Transformer

Usage

T1.1

NIUA0 Port 0 (Tx)

T2.1

NIUA0 Port 0 (Rx)

GND

T4.1

T5.1

GND

T7.1

T8.1

GND

10

T10.1

11

T11.1

12

GND

13

T13.1

14

T14.1

15

GND

16

T16.1

17

T17.1

18

GND

19

GND

20

T1.8

NIUA0 Port 0 (Tx)

21

T2.8

NIUA0 Port 0 (Rx)

22
23

T4.8

24

T5.8

25
27

T7.8

28

T8.8

29

T10.8

30

T11.8

31
32

T13.8

33

T14.8

34
35

T16.8

36

T17.8

Software
MCUF
There is a 20MByte Intel Series2 Flash PCMCIA card inside the MCUF. It contains software +
configuration for the BTS.

There once has been a mtd_iflash2.c driver for Linux 2.4.x, but apparently it has never been
merged mainline before the big CardServices? API redesign happened in 2.6.x. So
unfortunately it's not straight-forward to read them out :(
The MCUF is able to run without the PCMCIA card. In this case, it will download all software
+ config via E1 from the BSC.
The MCUF has a very extensive command line interface (MMI), for more information
check Motorola_Horizon_macro/MCUF_Console

CTU
It is assumed that the CTU only contains a boot loader to download the real software from
the MCUF.

Further reading

Motorola BSS11 Base Station Operational Aspects (Describes BTS hardware)


o

http://wenku.baidu.com/view/da379c82d4d8d15abe234e32.html

Motorola SYS01 GSM SYSTEM INTERFACES (Chapter 5: Mobis)


o

http://read.pudn.com/downloads61/ebook/212957/SYS01.pdf

ommand Reference MMI-ROM


chg_level
change the access level. If you want level 3 access, you have to type in the two passwords:
3stooges and 4beatles

set_site <siteID>
you can set the site ID (range: 0-104). However, the siteID must be identical with the siteID
stored on the PCMCIA card.
It seems for a Horizon macro (master cabinet) the site ID should be 18.
If you enter a wrong site ID, you will get a FATAL SWFM ERROR (Bad database - Cannot
adjust database for site). The system will reboot and you can try your luck with the next
site ID number ;)
Once you entered the correct siteID, the system transitions into the MMI-RAM prompt.
MMI-ROM 1015 -> set_site 18
Setting subsystem to 19 for site 18

Process 0x95 (Temp CM) requested a self-initiated soft reset

!!! REBOOT !!!

Reset due to self-initiated soft reset


[01/01/80 00:31:38] MMI-RAM 1015 -> Waiting for System Initialization
to complete.....

[01/01/80 00:31:49] MMI-RAM 1015 -> Database display commands accepted.


[01/01/80 00:31:54] MMI-RAM 1015 -> Initialization complete.
commands accepted.

All

Command reference MMI-RAM


state <siteID>
[01/01/80 00:32:03] MMI-RAM 1015 -> state

ERROR: Missing Parameters, only received: 0.

[01/01/80 00:32:18] MMI-RAM 1015 -> state 18

DEVICE STATUS INFORMATION FOR LOCATION 18:


OPER

STATES:

ADMIN STATES:

D:Disabled

E:Enabled

B:Busy

L:Locked

U:Unlocked

E:Equipped

S:Shutdown

Last Transition Related


Device

State Reason

dd/mm

hh:mm:ss Function

------------- ----- ------------------------- --------------------------CSFP 0 0 0

D-U

NO CODE

01/01

00:31:53 None

BTP 0 0 0

B-U

NO REASON

01/01

00:31:50 None

DRI 0 0 0

D-U

Code Load

01/01

00:32:01 None

DRI 0 1 0

D-U

DRI Not Detected

01/01

00:31:58 None

DRI 1 0 0

D-U

Code Load

01/01

00:32:01 None

DRI 1 1 0

D-U

DRI Not Detected

01/01

00:31:58 None

DRI 2 0 0

D-U

Code Load

01/01

00:32:01 None

DRI 2 1 0

D-U

DRI Not Detected

01/01

00:31:58 None

MSI 0 0 0

B-U

NO REASON

01/01

00:31:56 None

MMS 0 0 0

B-U

MMS Providing Clock

01/01

00:31:57 None

MMS 0 1 0

D-U

Synch Loss OOS Timer

01/01

00:31:57 None

RSL 0 0 0

E-U

64Kbps Link

01/01

00:31:57 None

RSL 0 1 0

D-U

NO REASON

01/01

00:31:42 None

GCLK 0 0 0

B-U

GCLK in Fast Tune Mode

01/01

00:31:57 None

EAS 0 0 0

B-U

NO REASON

01/01

00:31:50 None

CAB 0 0 0

B-U

NO REASON

01/01

00:31:42 None

SITE 0 0 0

D-U

NO REASON

01/01

00:31:42 None

PATH 0 0 0

D-U

NO REASON

01/01

00:31:42 None

PATH 0 1 0

D-U

NO REASON

01/01

00:31:42 None

FUNCTION STATUS INFORMATION FOR LOCATION 18:


OPER STATES:

E:Enabled

B:Busy

ADMIN STATES:

E:Equipped

Last Transition Related


Function

State Reason

dd/mm

hh:mm:ss Device

------------- ----- ------------------------- --------------------------RTF 0 0 0

E-E

NO REASON

01/01

00:31:42 None

RTF 0 1 0

E-E

NO REASON

01/01

00:31:42 None

RTF 1 0 0

E-E

NO REASON

01/01

00:31:42 None

RTF 1 1 0

E-E

NO REASON

01/01

00:31:42 None

RTF 2 0 0

E-E

NO REASON

01/01

00:31:42 None

END OF STATUS REPORT

Command Reference EMON


In order to enter EMON, you need to enter level3 of MMI-ROM and then press Ctrl+N

capture
[12/06/08 01:01:36] MCU:emon_1015 % capture

Data captured 12/06/2008 00:56:49

Process ID

Consumed

CPU

Time (us)

Util.

Message Message Receive Context


Send

Receive Suspend Switch

-------------- --------- ------- ------- ------- ------- ------00 Null

257143

1.01%

25

06 COM

1468

0.01%

07 btask

1241

0.00%

12 exec dlsp

14325

0.06%

15

22

22

22

14 tty_dlsp

15859

0.06%

75

28

29

16 filter

21657

0.09%

17 monitor

13700

0.05%

261

0.00%

3E mcu_dlsp

10473

0.04%

10

50 MIP

27834

0.11%

81

25

22

39

70 mmi_rom

3163

0.01%

F1 SWFM_PRINT

4153

0.02%

1E sync_fw_rl

Driver/OS

Consumed

CPU

Time (us)

Util.

Message Device
Send

System

Intr.

Calls

-------------- --------- ------- ------- ------- ------EXEC


TTY
FILTER

905
102

0.00%

80
1

COM

NVRAM

13

HDLC

5014

0.02%

15

34

ROUTER
TIMER

21
11

321418

1.27%

5200

QUICC

MSW

0.00%

952

PIX

SYNC

0.00%

Transition

Consumed

CPU

State

States

Time (us)

Util.

Count

-------------- --------- ------- ------Idle to INTR

24694428

97.25%

78

INTR to Idle

364

0.00%

53

CTXSW to Idle

491

0.00%

25

WARNING: Elapsed time and tick time do not match.


Elapsed time (microseconds) = 25393094
Tick time (microseconds) = 26000000

Consumed

CPU

Time (us)

Util.

Message Receive Context Device


Snd+Rcv Suspend Switch

Intr.

============== ========= ======= ======= ======= ======= =======


=======
Totals
1991

25393094 100.00%

Total - Null

25135951

98.99%

264

83

147

5237

System
Calls

Elapsed time = 25.39 seconds

msw_connects
[12/06/08 01:04:12] MCU:emon_1015 % msw_connects 0
Audit for LINK = 0.
TS

Source

(port-TS)

0x755

pattern 0x55

0x755

pattern 0x55

0x755

pattern 0x55

0x755

pattern 0x55

0x755

pattern 0x55

0x755

pattern 0x55

0x755

pattern 0x55

0x755

pattern 0x55

0x755

pattern 0x55

0x755

pattern 0x55

10

0x755

pattern 0x55

11

0x755

pattern 0x55

12

0x755

pattern 0x55

13

0x755

pattern 0x55

14

0x755

pattern 0x55

15

0x755

pattern 0x55

16

0x755

pattern 0x55

17

0x755

pattern 0x55

18

0x755

pattern 0x55

19

0x755

pattern 0x55

20

0x755

pattern 0x55

21

0x755

pattern 0x55

22

0x755

pattern 0x55

23

0x755

pattern 0x55

24

0x755

pattern 0x55

25

0x755

pattern 0x55

26

0x755

pattern 0x55

27

0x755

pattern 0x55

28

0x755

pattern 0x55

29

0x755

pattern 0x55

30

0x755

pattern 0x55

31

0x755

pattern 0x55

TCU Allocation Registers


TS Uplink value Downlink value
0

0x0001

0x0001

0x0001

0x0001

0x0001

0x0001

0x0301

0x0001

0x0001

0x0001

0x0101

0x0101

0x0001

0x0001

0x0001

0x0001

0x0001

0x0001

0x0301

0x0001

10

0x0001

0x0001

11

0x0001

0x0001

12

0x0001

0x0001

13

0x0001

0x0001

14

0x0001

0x0001

15

0x0001

0x0101

16

0x0001

0x0001

17

0x0001

0x0001

18

0x0001

0x0001

19

0x0001

0x0001

20

0x0001

0x0001

21

0x0201

0x0101

22

0x0001

0x0001

23

0x0001

0x0001

24

0x0001

0x0001

25

0x0301

0x0101

26

0x0001

0x0001

27

0x0001

0x0001

28

0x0001

0x0001

29

0x0301

0x0001

30

0x0001

0x0001

31

0x0001

0x0101

help

[01/01/80 00:00:37] MCU:emon_1015 % help


Commands available:
!

alias

analyze

baud

bstats

ca_iir_filter

capture

count_reset

coverage

csfp_objects

cstats

ctbl_objects

debug

dri_msg

eft

ex_iir_dis

ex_iir_mod

filter

help

history

iir_dis

iir_mod

iir_rte

iir_time_stamp

l_dump

l_modify

link_test

lstats

mem_use

memory

mmu_stats

msg_send

mstats

msw_connects

objects

pbegin

pcmcia

pend

perf

pstats

reset

rlogin

router_tbl

swfm

time
tty_backlog_dump

time_stamp

tstats

unalias

zstats

objects
Output of software objects with no PCMCIA card:
[01/01/80 00:00:49] MCU:emon_1015 % objects

Object
Object
Num
Name
Specific

Dv
Version

Date

Time

Checksum

Size

S Ty

=== ======== =========== =========== ===== ========== ======== = ==


============
000
c8

exec 08.00.00.35 24-Jan-2008 10:58 0x01ebf709 00418345 1 09

003
c8

null 08.00.00.35 24-Jan-2008 10:58 0x00008c25 00000492 2 09

004
c8

bootlib 08.00.00.35 24-Jan-2008 11:09 0x0017f900 00017866 1 09

006
c8

ex_com 08.00.00.35 24-Jan-2008 11:04 0x001abe24 00019575 2 09

007
cf

btask 08.00.00.35 24-Jan-2008 11:05 0x0009857d 00007128 2 09

008
0f

mcuboot 08.00.00.35 24-Jan-2008 11:09 0x03d4e1ed 00807616 1 09

018
c8

ex_dlsp 08.00.00.35 24-Jan-2008 11:02 0x0033707c 00039088 2 09

020
c8

ex_tty 08.00.00.35 24-Jan-2008 10:59 0x00134363 00013699 2 09

022
c8

ex_ftr 08.00.00.35 24-Jan-2008 11:03 0x000d2ed8 00010770 2 09

023
c8

emon 08.00.00.35 24-Jan-2008 11:00 0x00831024 00094654 2 09

030
88

xsync_f 08.00.00.35 24-Jan-2008 11:01 0x00040687 00002994 2 09

062
8f

mcu_dsp 08.00.00.35 24-Jan-2008 11:06 0x002c28de 00033739 2 09

080
c8

mip 08.00.00.35 24-Jan-2008 11:08 0x007d65ab 00089895 2 09

111
8f

mmi_rom 08.00.00.35 24-Jan-2008 11:09 0x001ac15c 00019855 2 09

160
uboot 06.05.00.04 20-Jun-2001 11:00 0x000c74a6 00008641 1 10 88
0000 0000

Load version information not present


Output of objects with PCMCIA card installed:
[12/06/08 01:03:11] MCU:emon_1015 % objects

Object
Object
Num
Name
Specific

Dv
Version

Date

Time

Checksum

Size

S Ty

=== ======== =========== =========== ===== ========== ======== = ==


============
000
c8

exec 08.00.00.35 24-Jan-2008 10:58 0x01ebf709 00418345 1 09

002
dbase 00.00.03.fd 15-May-2008 11:12 0x026205f6 01069062 1 03
14d1 eef8
003
c8

null 08.00.00.35 24-Jan-2008 10:58 0x00008c25 00000492 2 09

004
c8

bootlib 08.00.00.35 24-Jan-2008 11:09 0x0017f900 00017866 1 09

005
f8

libcomn 08.00.00.00 08-Jun-2004 10:59 0x00004303 00000202 1 06

006
c8

ex_com 08.00.00.35 24-Jan-2008 11:04 0x001abe24 00019575 2 09

007
cf

btask 08.00.00.35 24-Jan-2008 11:05 0x0009857d 00007128 2 09

008
0f

mcuboot 08.00.00.35 24-Jan-2008 11:09 0x03d4e1ed 00807616 1 09

012
20

rssboot 08.00.00.35 24-Jan-2008 12:11 0x020a40c5 00290068 1 12

013

options 09.00.00.00 05-Mar-2008 13:04 0x0002281d 00001144 1 04

018
c8

ex_dlsp 08.00.00.35 24-Jan-2008 11:02 0x0033707c 00039088 2 09

020
c8

ex_tty 08.00.00.35 24-Jan-2008 10:59 0x00134363 00013699 2 09

022
c8

ex_ftr 08.00.00.35 24-Jan-2008 11:03 0x000d2ed8 00010770 2 09

023
c8

emon 08.00.00.35 24-Jan-2008 11:00 0x00831024 00094654 2 09

030
88

xsync_f 08.00.00.35 24-Jan-2008 11:01 0x00040687 00002994 2 09

032
b8

cp_rrsm 08.00.00.34 07-Dec-2007 10:47 0x026ca2ec 00487135 1 05

034
b8

cp_crm 08.00.00.35 24-Jan-2008 12:04 0x056d776f 01082366 1 05

036
b8

cp_cbs 08.00.00.33 05-Nov-2007 09:52 0x007181c0 00090582 1 05

048
30

rs_cfm 08.00.00.33 05-Nov-2007 09:51 0x00390f3b 00031855 1 07

049
30

rs_ho 08.00.00.34 07-Dec-2007 11:00 0x008bb71f 00077886 1 07

050
30

rs_lyr1 08.00.00.34 07-Dec-2007 11:16 0x00d7d4cb 00121095 1 07

051
30

rs_abis 08.00.00.34 07-Dec-2007 11:29 0x00720c0e 00063101 1 07

052
30

rs_lyr2 08.00.00.33 05-Nov-2007 10:48 0x002892c2 00022675 1 07

060
3f

sm_mbts 08.00.00.33 05-Nov-2007 09:46 0x005bc0b7 00069519 1 09

062
8f

mcu_dsp 08.00.00.35 24-Jan-2008 11:06 0x002c28de 00033739 2 09

068
f8

fm_crtr 08.00.00.35 24-Jan-2008 10:59 0x0008f60c 00011626 1 06

070
3f

fm_mvp 08.00.00.35 24-Jan-2008 11:28 0x0022af26 00027024 1 09

071
3f

fm_mca 08.00.00.35 24-Jan-2008 11:54 0x041a22e4 00781446 1 09

072
3f

fm_sync 08.00.00.33 05-Nov-2007 10:46 0x003f2bff 00046487 1 09

075
f8

fm_ftp 08.00.00.34 07-Dec-2007 10:38 0x0205c69c 00409054 1 05

076
b8

fm_mmf 08.00.00.33 05-Nov-2007 11:10 0x00367cbe 00042382 1 05

077
f8

fm_sap 08.00.00.35 24-Jan-2008 11:01 0x00636f45 00077150 1 05

079
3f

fm_mfcp 08.00.00.33 05-Nov-2007 10:05 0x007d4ef2 00098860 1 17

080
c8

mip 08.00.00.35 24-Jan-2008 11:08 0x007d65ab 00089895 2 09

097
b8

st_ssp 08.00.00.33 05-Nov-2007 10:12 0x000f4cdd 00011373 1 05

111
8f

mmi_rom 08.00.00.35 24-Jan-2008 11:09 0x001ac15c 00019855 2 09

113
f8

om_cm 08.00.00.34 07-Dec-2007 11:00 0x053d9ec8 01054286 1 05

120
3f

om_mmmi 08.00.00.35 24-Jan-2008 11:33 0x038690c2 00699229 1 09

160
uboot 06.05.00.04 20-Jun-2001 11:00 0x000c74a6 00008641 1 10 88
0000 0000
165 TSM_FEP 08.00.00.07 27-Oct-2004 22:31 0x00258b0f 00020528 1 16 b0
0a00 0200

166
CC_TSM 08.00.00.30 12-Sep-2007 05:31 0x008db67d 00077444 1 16 b0
0a00 1800
169

a51 08.00.00.00 22-Jun-2004 13:13 0x00011259 00001077 1 19

170

a52 08.00.00.00 22-Jun-2004 13:13 0x0001519b 00001290 1 19

177
niu 08.00.00.30 11-Sep-2007 13:01 0x0118f93a 00163419 1 10 bf
0018 0200
184

cs1_ccc 08.00.00.35 22-Jan-2008 14:39 0x010b4a4f 00146012 1 18

185

cs1_eqc 08.00.00.0a 13-Jan-2005 16:30 0x015a0a59 00185538 1 18

193
001100 08.00.00.00 21-Jun-2004 10:53 0x00014b89 00001311 1 08 b8
0011 0000
194
001100 08.00.00.00 21-Jun-2004 11:42 0x0001cdf8 00001607 1 08 b8
0011 0000
200 sync_fw 08.00.00.00 16-Jun-2004 15:52 0x007756ac 00127364 1 26 bf
000f 0000
201
SCP 08.00.00.13 19-Jul-2005 19:07 0x00ae701f 00161502 1 08 b8
0a00 0300
202
SEQ 08.00.00.09 09-Dec-2004 22:21 0x001dfba4 00029750 1 08 b8
0a00 0300
207 niu_hds 07.06.00.00 15-Nov-2000 15:23 0x015f6b88 00229657 1 10 bf
0000 0202

Load version information not present

pstats
[12/06/08 01:02:14] MCU:emon_1015 % pstats
PROCESS

USER_STACK

MAILBOXES

ID NAME
PEAK

INSTANCE PRIORITY

SIZE

MAXIMUM CURRENT

-- -------

-------- --------

----

------- -------

00 Null
0014

00000003

00

00001000

0020

0014

06 COM
0002

00000006

05

00008000

0022

0002

07 btask
0005

00000007

01

00004000

0009

0005

12 exec dlsp
0010

00000012

19

00008000

0080

0010

14 tty_dlsp
000c

00000014

04

00004000

000c

000c

16 filter
0004

00000016

02

00004000

0009

0004

17 monitor
0014

00000017

03

00005000

0020

0014

1e sync_fw_rl
0001

0000001e

04

00004000

000c

0001

3e mcu_dlsp
0007

0000003e

05

00002000

000a

0007

50 MIP
002c

00000050

0f

00002000

0032

002c

70 mmi_rom
0006

0000006f

03

00004000

0006

0006

f1 SWFM_PRINT
0000

00000000

03

00004000

0000

0000

Logs
Normal boot log with PCMCIA card installed
!!! REBOOT !!!

Memory full configured Reset due to power reset


Checking DRAM: 16 of 16 MB complete
Motorola MCU Boot Software Version 1.8.0.0.35 24-Jan-08
Copyright 2008, Motorola Incorporated
Board type is MCU-F
QUICC microcode revision 0x0083
Exec microboot version 4
taking PCMCIA version of object 2

taking PCMCIA version of object 5


taking PCMCIA version of object 12
taking PCMCIA version of object 13
taking PCMCIA version of object 32
taking PCMCIA version of object 34
taking PCMCIA version of object 36
taking PCMCIA version of object 48
taking PCMCIA version of object 49
taking PCMCIA version of object 50
taking PCMCIA version of object 51
taking PCMCIA version of object 52
taking PCMCIA version of object 60
taking PCMCIA version of object 68
taking PCMCIA version of object 70
taking PCMCIA version of object 71
taking PCMCIA version of object 72
taking PCMCIA version of object 75
taking PCMCIA version of object 76
taking PCMCIA version of object 77
taking PCMCIA version of object 79
taking PCMCIA version of object 97
taking PCMCIA version of object 113
taking PCMCIA version of object 120
taking PCMCIA version of object 165
taking PCMCIA version of object 166
taking PCMCIA version of object 169
taking PCMCIA version of object 170

taking PCMCIA version of object 177


taking PCMCIA version of object 184
taking PCMCIA version of object 185
taking PCMCIA version of object 193
taking PCMCIA version of object 194
taking PCMCIA version of object 200
taking PCMCIA version of object 201
taking PCMCIA version of object 202
taking PCMCIA version of object 207
MMI-ROM 0000 ->
MMI-ROM 0000 ->
MMI-ROM 1015 ->

Normal boot log with no PCMCIA card installed


!!! REBOOT !!!

Memory full configured Reset due to power reset


Checking DRAM: 16 of 16 MB complete
Motorola MCU Boot Software Version 1.8.0.0.35 24-Jan-08
Copyright 2008, Motorola Incorporated
Board type is MCU-F
QUICC microcode revision 0x0083
Exec microboot version 4
PCMCIA: Socket 0 empty.
MMI-ROM 0000 ->
MMI-ROM 0000 ->
MMI-ROM 1015 ->

emon start log after Ctrl+N

MCU:emon_1015 %
[12/06/08 01:06:53] MCU:emon_0000 % Database is not compressed

MIP: Starting Micro IP


MIP: In slot 0
MIP: csfp_swap = 'NO_CSFP_SWAP'
MIP: Reset type is x48000025.
MIP: Current seconds is 897700014.
MIP: Soft reset count read is 0.
MIP: Writing time 897700014, count 1.
MIP: Will contact BSC.
MIP: Performing Hard Reset.
MIP: Disable phase detector 1 and 2
MIP: SYNC pulse the phase det strobe
MIP: 1015 is master MCU
MIP: Establishing links to NIU frame 0, slot 0
MIP: Establishing links to NIU frame 1, slot 0
NG EXEC DLSP dl_message_con:

Control mailbox opened for channel 1,

NG EXEC DLSP dl_message_con:


hdlc link, channel 1

HDLC link active timer started for first

NG EXEC DLSP dl_message_con:

Control mailbox opened for channel 3,

NG EXEC_DLSP process_hdlc_msg:
Mailbox id = 1001

LINK ESTABLISHED for channel 1, Link

NG EXEC_DLSP process_hdlc_msg:

LUI mailbox created

NG EXEC_DLSP process_hdlc_msg:

Low priority LAPD mailbox created

NG EXEC_DLSP process_hdlc_msg:

HDLC link active timer stopped.

NG EXEC_DLSP process_hdlc_msg:
= 3001h

NIU Flow mailbox id for local channel 1

MIP: HDLC link connected on frame 0, slot 0

[12/06/08 01:06:54] MCU:emon_1015 % MIP: CPU assigned ok on frame 0,


slot 0
MIP: NIU/NIU2 set for E1 interface
MIP: Default span 0 CHECKED HDSL settings are, ptype=0, msett=2.
MIP: Default span 1 CHECKED HDSL settings are, ptype=0, msett=2.
MIP: Default span 2 CHECKED HDSL settings are, ptype=0, msett=2.
MIP convert_to_niu_data.c: NIU/NIU2 config type is 8, int_hdsl_flag=0,
ext_hdsl_flag=0, hdsl_16_ts_flag=0.
MIP: Span response from NIU/NIU2 is PASS
MIP: Span data has been set for NIU/NIU2 on frame 0, slot 0
MIP: NIU/NIU2 set for E1 interface
MIP: Default span 0 CHECKED HDSL settings are, ptype=0, msett=2.
MIP: Default span 1 CHECKED HDSL settings are, ptype=0, msett=2.
MIP: Default span 2 CHECKED HDSL settings are, ptype=0, msett=2.
MIP convert_to_niu_data.c: NIU/NIU2 config type is 8, int_hdsl_flag=0,
ext_hdsl_flag=0, hdsl_16_ts_flag=0.
MIP: Span response from NIU/NIU2 is PASS
MIP: Span data has been set for NIU/NIU2 on frame 0, slot 0
MIP: Link state 1, channel 0, span 0, timeslot 1.
MIP: Current link owner is process 80, cpu x1015, mbox x7001.
MIP: Current span is 0; current timeslot is 1; expected 0 1.
MIP: Establishing second RSL on NIU/NIU2 frame 0, slot 0, span 1,
timeslot 2
MIP: Link state 1, channel 1, span 1, timeslot 2.
MIP: Current link owner is process 80, cpu x1015, mbox x7003.
MIP: Current span is 1; current timeslot is 2; expected 1 2.
NG EXEC DLSP dl_message_con:

Control mailbox opened for channel 5,

NG EXEC_DLSP process_hdlc_msg:
Mailbox id = 9001

LINK ESTABLISHED for channel 5, Link

NG EXEC_DLSP process_hdlc_msg:
= 5001h

NIU Flow mailbox id for local channel 5

MIP: HDLC link connected on frame 0, slot 0, span 1


MIP: Link state 1, channel 1, span 1, timeslot 2.
MIP: Current link owner is process 80, cpu x1015, mbox x7003.
MIP: Current span is 1; current timeslot is 2; expected 1 2.
MIP: Bad EXEC DLSP return code 1
MIP: HDLC link failed to connect on frame 1, slot 0 with code 5
MIP: Tag 0x00 indicates nv_write successful!

[12/06/08 01:12:17] MCU:emon_1015 %

You might also like