You are on page 1of 2

Asian Paints WoodTech Melamyne

Gold Clear
PRODUCT CODE: 2355, 2356, 2357

WOODTECH MELAMYNE GOLD CLEAR BENEFITS

NON YELLOWING GOOD GLOSS RETENTION RESISTANCE HARDNESS


WoodTech Melamyne Gold WoodTech Melamyne Gold WoodTech Melamyne Gold Clear The hard film of WoodTech
Clear is specially formulated to Clear Glossy has good gloss Interior has moderate scratch, Melamyne Gold Clear protects
resist yellowing of the film over retention and keeps your stain and heat resistance. your interior furniture effectively
the years. furniture looking shiny for against daily wear and tear.
years.

PRODUCT FEATURES
DURABILITY COLOURS AVAILABLE AVAILABLE PACKS

BEST IN CLASS
CLEAR
HIGH
Range of 9 attractive
MODERATE Translucent Asian Paints
Interior Woodtech Wood Stains,
LOW & 6 Aquadur Water based Wood Stain 500 ml 1 Ltr 4 Ltr 20 Ltr
available to add/change colour.
WoodTech Melamyne Gold clear Matt ( 2355)- 500 ml,1lt, 4 lts, 20 lts
WoodTech Melamyne Gold clear Glossy ( 2356)- 500 ml,1lt, 4 lts, 20 lts
COVERAGE FINISH WoodTech Melamyne Gold clear Sealer ( 2357)- 500 ml,1lt, 4 lts, 20 lts

On smooth sanded wooden


surface by Spraying MATT SEMI GLOSS GLOSS HIGH GLOSS
80-100 sq.ft/ltr/Coat**

** Actual coverage may vary from the quoted


coverage due to factors such as method and
condition of application and surface roughness.

HOW TO APPLY PAINT APPLICATION PROCESS


APPLICATION PRODUCT MIXING RATIO OF THINNER DILUTION % VISCOSITY RECOATING
PRE PAINTING STEPS CODE BASE: HARDENER ( BY VOL) (BY VOL) (SEC) PERIOD (HRS)
STEP 1
WOODTECH MELAMYNE 2357 90:10 AP Thinner for SPRAY : 20-40 ; SPRAY : 20-25 SPRAY : 5-6 HRS
1.Sand the wooden surface along GOLD CLEAR SEALER 1ST Melamyne(Brushing)- BRUSH : 20-40 SECS BRUSH : 8-10 HRS
the grains using sand paper No. BRUSH : 20-25 WET ON WET 15 Min
COAT (2126) or Thinner
180, and then 320 or 400.Wipe
surface to clean off loose dust SPRAY/BRUSH T-124 (Spraying)-(0632)
particles. SANDING Sand the surface with Sand paper 320 or 400 and wipe clean
2. If the surface has dents, apply STEP 2
Aquadur Dent Filler with a putty WOODTECH MELAMYNE 2357 90:10 AP Thinner for SPRAY : 20-40 ; SPRAY : 20-25 SPRAY : 5-6 HRS
knife over the dented area. GOLD CLEAR SEALER 2ND Melamyne(Brushing)- BRUSH : 20-40 SECS BRUSH : 8-10 HRS
COAT (2126) or Thinner BRUSH : 20-25 WET ON WET 15 Min
SPRAY/BRUSH T-124 (Spraying)-(0632)

3. To colour, Apply WoodTech Sand with Sand Paper No. 320 or 400 And Wipe Clean
Wood stains or Aquadur Wood ( Apply 3rd Coat if required Before Top coat Application, Sand with Sand Paper no. 320 / 400 and wipe clean )
stain by Ragging. Allow to dry for STEP 3
30 to 120 minutes. WOODTECH MELAMYNE 2355/2356 90:10 AP Thinner for SPRAY : 20-40 ; SPRAY : 20-25 SPRAY : 5-6 HRS
GOLD CLEAR MATT/ Melamyne(Brushing)- BRUSH : 20-40 SECS BRUSH : 8-10 HRS
GLOSSY 1ST COAT (2126) or Thinner BRUSH : 20-25 WET ON WET 15 Min
Note: 1. If required, apply Asian Paints WoodTech Wood Stain or Aquadur SPRAY/BRUSH T-124 (Spraying)-(0632)
Wood Stain by ragging on sanded wooden surface and allow
30-120 minutes of drying time. SANDING Sand the surface with Sand paper 320 or 400 and wipe clean
2. Mixing Ratio for Asian Paints Melamyne Gold Clear Base : Hardener
is 90:10 by volume. STEP 4
3. Asian Paints WoodTech Melamyne Gold Clear Base should be
thoroughly stirred and mixed with the hardener and thinner in WOODTECH MELAMYNE 2355/2356 90:10 AP Thinner for SPRAY : 20-40 ; SPRAY : 20-25 SPRAY : 5-6 HRS
the specified mixing ratio. GOLD CLEAR MATT/ Melamyne(Brushing)- BRUSH : 20-40 SECS BRUSH : 8-10 HRS
4. Asian Paints WoodTech wood stains should not be mixed with BRUSH : 20-25 WET ON WET 15 Min
Asian Paints WoodTech Melamyne Gold Clear Base. GLOSSY 2ND COAT (2126) or Thinner
5. Mix Matt and Glossy finishes for desired level of sheen. SPRAY/BRUSH T-124 (Spraying)-(0632)
6. Use only Basecoat or Top coat during wet on wet application.
7. Asian Paints WoodTech Melamyne Gold Clear must not be polluted ( Apply 3rd Coat if required after sanding with Sand Paper no. 320 / 400 and wipe clean )
with oil, varnish or the like and must not be sanded with steel
wool between coats.
8. Recoat period is quoted for 30C and 75% relative humidity, these
may vary under different conditions.
9. Spraying air pressure 2.2 to 2.8 Kgs/sq.cm.
10. Viscosity as measured through a Ford cup B4 at 30C.
Asian Paints WoodTech Melamyne
Gold Clear

HOW TO CHOOSE COLOUR

WOODSTAIN FANDECK AQUADUR WOOD STAINS SHADE CARD WOODTECH WOODSTAIN SHADE CARD

ADDITIONAL INFORMATION

POST PAINTING CARE PRECAUTIONS


For removing stains on tiles and metal surfaces, For optimum performance, Asian Paints Woodtech Melamyne Gold Clear must be
apply NC Thinner on the surface and wipe clean. applied at a temperature between 20C and 40C and humidity not above 75%
If stains are difficult to remove, scrapping can be Do not over-thin and mix according to recommended ratios
done after applying NC thinner on the stained area. Stir well and strain before use.
Precautions need to be taken while spraying /
brushing, like masking of adjourning areas with
suitable material, as the stains may be difficult to
remove if present on wood or coated wooden and
wall surfaces.

TECHNICAL DETAILS SAFETY FEATURES


a. Drying time: Surface dry time 20 minutes. Kindly refer to the MSDS for Asian Paints Woodtech Melamyne Gold Clear Sealer,
Tack Free time 2 hrs. Gloss and Matt, which gives detailed information on safety measures while
b. Gloss levels: 80% minimum (Glossy) and 10-15% (Matt) handling the paint.
on coated wooden pannel at 60 Gloss Head. Store the product at ambient conditions in well ventilated locations and away from
c. Flash point (IS 101/1987, Part 1, Sec 6): source of ignition and fire
Above 25C (77F) Use protective equipment like rubber/polyurathene gloves, safety goggles/glasses,
d. Stability of thinned paint: To be used within 8 hours face mask while handling the paint
e. Shelf Life: 3 years from date of manufacture in original Avoid eye and skin contact. In both cases wash with soap and plenty of water. Get
tightly closed container away from direct sunlight and medical attention if irritation develops or persists.
extensive heat. Do not inhale or ingest. In case of inhalation move to fresh air and seek medical
attention if symptoms persist in both cases
Dispose in land filling. Do not dispose in any drain or land filling
No added Lead, Mercury or Chromium compounds
Flamable

You might also like