You are on page 1of 104

(Subject To Change Without Notice) CONSTRUCTION PRODUCTS C-3-ZAXIS 130-5-1

ZAXIS 130-5 EXCAVATOR


Equipment for Base Machine

ENGINE: *One Upper Rollers Gauge


*Isuzu AI-4JJ1X - certified to Spring Applied Hydraulic Engine Coolant Temperature
IT4 / Stage IIIB emissions Released Propel Brake Warning Indicator with Audible
*97 Horsepower (72 kW) Net Rated Alarm
Power (ISO9249) UPPER STRUCTURE: Engine Oil Pressure Warning
Turbocharger *Right, Left, and Counterweight Indicator with Audible Alarm
Electronic Engine Control Unit Mirrors(3) Fuel Gauge with Low Fuel
Auto-Idle System Toolbox Indicator
Antifreeze Protection to -34F Vandal Locks for: Work Mode Indicator
(-37C) Cab Door Auto Idle Indicator
Enclosed Fan Guard Service Doors Alternator Charge Indicator
Dual Element Dry-type Air Filter Fuel Cap Air Filter Restriction
with Restriction Indicator Tool Box Indicator
Full Flow Oil Filter *Counterweight, 5,512 lbs. Fault Code Alert Indicator
Double Fuel Filter (2,500 kg) Check Engine Indicator
Water Separator Work Lights: Wiper Mode Indicator
*Underhood Diesel Particulate One Mounted on Frame Work Lights On Indicator
Filter with Curved Exhaust One Mounted on Boom Fuel Rate Display
*Radiator, Oil Cooler, Remote Mounted Engine Oil and Clock
Intercooler with Dust Net Fuel Filters Hour Meter
Glow Plug Start Aid Mode Selection:
50-Amp Alternator - 24 Volt FRONT ATTACHMENT: One Work Mode
500 Hour Engine Oil Change Oil Impregnated Bushings Three Power Modes
Interval Reinforced Resin Thrust Plates Numerous Attachment Modes
Engine Oil Drain Coupler Tungsten Carbide Thermal Coating Auto-Climate Control/Air
70% (35 degree) Off Level on arm to Bucket Joint Conditioner, Heater with
Capability Centralized Lubrication System Pressurizer
Isolation Mounted Dirt Seals on Bucket Pins AM-FM Radio
Less Boom Machine Information Center (MIC)
HYDRAULICS: Less Arm Windshield Wiper/Washer with
Open Center, Load Sensing with Less Bucket Intermittent Speed
Variable Displacement Pumps 12V-60W, 5 Amp Cell Phone Power
Hydraulic Pilot Controls OPERATOR'S STATION: Outlet
Axial Piston Swing Motor ZXLink Ultimate Machine 2 In. Retractable Seat Belt
Multiple Wet Disk Swing Brake Monitoring System w/ 3-year Tinted Safety Glass
Auxiliary Valve Section Message Service (Available in Hot/Cold Box Compartment
Adjustable Flow for Attachments United States and Canada only) Horn
Through Monitor Adjustable Control Positions Two Cup Holders
Boom and Arm Reduced Drift (Levers to Seat, Seat to Pedals) Interior Light
Valves 4" Arm Rests Attached to Side Coat Hook
Power Boost Consoles Floor Mat
Auto Power Lift Pilot Control Shut-Off Lever Motion Alarm with Cancel Switch
Hydraulic Tank Site Gauge Short Stroke, Low Effort Pilot Transparent Tinted Roof Hatch
5,000 Hour Hydraulic Oil Change Levers with Sunshade
Interval Switches for Auxiliary Hydraulic Four Fluid-Filled Elastic Mounts
Control on RH Pilot Lever Easy Access Air Conditioning
UNDERCARRIAGE: Deluxe Adjustable Cloth Seat Filter
Two Speed Propel with Auto-Shift with Suspension, Reclining
Axial Piston Propel Motors Backrest, Headrest, and
Propel Motor Shields Adjustable Lumbar Support
Planetary Final Drives Multifunction, Color LCD Monitor
Sealed Track Chain System with:
Front and Center Track Guides Diagnostic Capability
Provisions for Tie Downs Systems Monitoring Capability
X-Frame Car Body Multiple Language Capability
Hydraulic Track Adjuster Maintenance Tracking
Eight Lower Rollers Engine Coolant Temperature

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B Kernersville, North Carolina for Complete Machine.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS C-3-ZAXIS 130-5-2
ZAXIS 130-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

BASE MACHINE Continued...


05U0FF ZAXIS 130-5 EXCAVATOR 158,139.00

MACHINE CONNECTIVITY
Machine connectivity functions require cellular coverage. Usage of ZXLink System requires
customer's acceptance of the terms of the John Deere Telematics System Contract.

Option availability limited by specific geographical regions. Please refer to region specific price
pages for appropriate ordering codes.

1700 ZXLink Ultimate Cellular for the Americas, excluding Costa Rica In Base Price
Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway
(MTG), and ZXLink Ultimate activation.

Includes 3 year subscription. Annual subscription renewal required after 3 years for continued
functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to
www.StellarSupport.com to renew or update ZXLink subscriptions.

1741 No ZXLink Ultimate No Charge

TRACK SHOES
3200 600 mm (24 In.) Triple Semi Grousers without Backfill Blade In Base Price
Recommended for rocky terrain, hard ground and stumps.

3205 600 mm (24 In.) Triple Semi Grousers with 2590 mm (8'6") wide Backfill Blade 13,664.00
Recommended for rocky terrain, hard ground and stumps.

3250 700 mm (28 In.) Triple Semi Grousers without Backfill Blade 645.00
Recommended for general conditions and soft terrain.

3255 700 mm (28 In.) Triple Semi Grousers with 2690 mm (8'10") wide Backfill Blade 14,292.00
Recommended for general conditions and soft terrain.

3260 600 mm (24 In.) Rubber Crawler Pads without Backfill Blade 10,190.00
Rubber pads are laminated to track shoe.
This option requires a long lead time, contact your dealer for availability of this option.

3265 600 mm (24 In.) Rubber Crawler with 2590 mm (8'6") wide Backfill Blade 24,267.00
Rubber pads are laminated to track shoe.
This option requires a long lead time, contact your dealer for availability of this option.

SEATS
4125 Seat, Standard Mechanical In Base Price

4130 Seat, Heated Air-Suspension 785.00

BOOM
6801 Less Boom In Base Price
Excludes Arm Cylinder, Boom Cylinders and Plumbing on Boom.
Includes Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins.
Requires code 7001, "Less Arm".
The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is
recommended

6835 One Piece Boom with Arm Cylinder and Plumbing 13,190.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS C-3-ZAXIS 130-5-3
ZAXIS 130-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price
Hydraulic Filter Indicator Recommended.

7140 2.52 M (8 ft. 3 in.) Arm with Bucket 8,465.00


Cylinder and Linkage

7180 3.01 M (9 ft. 11 in.) Arm with Bucket 9,719.00


Cylinder and Linkage

AUXILIARY HYDRAULICS
7401 Less Auxiliary Hydraulics In Base Price

7420 Auxiliary High-Flow Hydraulic Lines for 2.52 M Arm w/ 2-Way Foot Controller 6,016.00

7430 Auxiliary High-Flow Hydraulic Lines for 3.01 M Arm w/ 2-Way Foot Controller 6,138.00

7440 Auxiliary High-Flow Hydraulic Lines Only for 2.52 M Arm 3,996.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

7450 Auxiliary High-Flow Hydraulic Lines Only for 3.01 M Arm 4,118.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

BUCKETS
8001 Less Buckets In Base Price
Includes bucket mounting pins.

8410 24 In. (600 mm), 0.48 Yd3 (0.37 M3) Heavy-Duty Bucket 4,201.00
Includes Four (4) Esco Super-V EV23SYL Teeth

8420 30 In. (750 mm), 0.65 Yd3 (0.50 M3) Heavy-Duty Bucket 4,442.00
Includes Four (4) Esco Super-V EV23SYL Teeth

8430 36 In. (900 mm), 0.81 Yd3 (0.62 M3) Heavy-Duty Bucket 4,967.00
Includes Five (5) Esco Super-V EV23SYL Teeth

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9150 Light Package 727.00
Additional 2 Cab lights, with 1 Right hand Boom Light.

9500 Mechanical Control-Pattern Selector 1,333.00

9803 Special Export Preperation-- Do not install front for shipping No Charge
For Export Containerization

9909 Non-Export Rust Preventive Coating 229.00


Non-English Operator's Manuals
Translated Customer Delivery Packets can be ordered using the John Deere Technical Information
Bookstore at http://www.johndeeretechinfo.com at no charge. The Translated Delivery Packets
include the Operator Manual, Decal Kit, Warranty Information Booklet, and Uptime Maintenance
Planner. Search for and order the Translated Delivery Packets by model and language that meets
your customer requirements. A listing of all Translated Delivery Packets available can be found by
selecting Translated Delivery Packets from the Manual Type dropdown list. Technical support is

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS C-3-ZAXIS 130-5-4
ZAXIS 130-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

OPTIONAL EQUIPMENT--ORDER AS DESIRED Continued...


available by calling 1-866-213-3373.

Machine Information Center, PLUS


Machine Information Center (MIC) kits can be ordered using the Technical Information Web
Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC.
MIC_Plus is for certain customers that would like the ability to perform their own diagnostics as well
as downloading MIC data using an approved PDA. This software is not available directly to
customers and Service Department should be advised before providing MIC_Plus to customers. There
are 2 types of MIC_Plus kits available:
1. Complete MIC_Plus (Customer Diagnostics) - Includes PDA, Software and Cables
2. Update MIC_Plus (Customer Diagnostics) - Includes only Diagnostics cable and latest software
Technical support for the Customer MIC program is the responsibility of the selling dealer. Technical
support for using the Technical Information Web Bookstore can be obtained by calling
1-866-213-3373.

Machine Information Center, Standard


Machine Information Center (MIC) kits can be ordered using the Technical Information Web
Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC.
MIC Download is used for downloading MIC controller only using an approved PDA. Customer then
transfers information to PC for viewing stored information. There are 2 types of kits available for
customers:
1. Complete MIC for Customer Download - Includes PDA, Software and Cables
2. Update MIC for Customer Download - Includes only download cable and latest software
Technical support for the Customer MIC program is the responsibility of the selling dealer.
Technical support for using the Technical Information Web Bookstore can be obtained by calling
1-866-213-3373.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Heavy-Duty:
Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339032 24 In (610 mm), 0.48 yd3 (0.37 M3) Heavy-Duty Bucket 3,370.00
Includes Four (4) Esco Super-V EV23SYL Teeth

AT339034 30 In (762 mm), 0.65 yd3 (0.50 M3) Heavy-Duty Bucket 3,584.00
Includes Four (4) Esco Super-V EV23SYL Teeth

AT339036 36 In (914 mm), 0.81 yd3 (0.62 M3) Heavy-Duty Bucket 4,084.00
Includes Five (5) Esco Super-V EV23SYL Teeth

AT339038 42 In (1067 mm), 0.99 yd3 (0.76 M3) Heavy-Duty Bucket 4,204.00
Includes Five (5) Esco Super-V EV23SYL Teeth

Guards:

AT390802 Cab FOPS Guard 2,533.00


FOPS Level II, ISO 10262 Certified

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS C-3-ZAXIS 130-5-5
ZAXIS 130-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Hydraulic Couplers:

AT343227 Hydraulic Quick Coupler 7,520.00

AT345608 Installation Charge for Hydraulic Coupler 1,015.00


Installation Charge Order also requires attachment part number, SHIP-TO address for Paladin
Custom Works, AND reference related machine order number.
The related machine order must reference the attachment order number.
Order code available only for Kernersville, North Carolina installations.

Hydraulic Thumb Kits:


Please click on the following link to access the freight rate tables.

AT339844 Deere/Hitachi Hydraulic Thumb Installation 1,871.00


Labor for installation of Deere/Hitachi thumb at Paladin Customworks Kernersville, NC.

AT379640 Hydraulic Thumb Kit, Direct 7,534.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379641 Hydraulic Thumb Kit, Direct for Couplers 7,534.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379642 Hydraulic Thumb Kit, Progressive 9,685.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379643 Hydraulic Thumb Kit, Progressive for Couplers 8,071.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

Hydraulics:

AT418447 Auxiliary High-Flow Lines for 2.52 M Arm 3,396.00

AT418449 Auxiliary High-Flow Lines for 3.01 M Arm 3,513.00

AT343969 Auxiliary Hydraulics, Attachment Combination Kit 424.00


Requires Auxiliary High-Flow Hydraulic Lines.
Allows for a combination of attachments (i.e. hammer and thumb) to be connected to the high-flow
lines, ready for operation.
Kit includes parts to replace the arm tube of the high-flow hydraulic lines with a short tube and uses
the existing stop valves to shut-off thumb operation when not in use.

AT327652 Control Handle for Auxiliary Hydraulics, Left-Hand 505.00


Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size
excavators.
Requires control solenoid for either 1-way or 2-way auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS C-3-ZAXIS 130-5-6
ZAXIS 130-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT390742 Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch 913.00
Does not use the monitor for flow control.
Does not require solenoids for auxiliary hydraulics.
Includes foot switch, solenoid, relays, wiring, and hoses.

AT390718 Control Solenoids for 2-Way Auxiliary Hydraulics 768.00


Monitor can be used to control hydraulic flow.
Can be used with either right-hand or left-hand control handle.

AT418450 Foot Control, Two-Way Hydraulics 1,931.00

AT339802 Hydraulic Filter Restriction Indicator Kit 758.00

AT418446 Mechanical Control Pattern Selector Kit 967.00


Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control
pattern.
Some excavators require additional parts.

AT390776 Single Pedal Propel Kit 2,039.00

Operator Environment:

AT390824 Guard, Lower Front Window ISO Level II 1,028.00

AT390823 Guard, Upper Front Window ISO Level II 772.00

ETN93549 MP3 Player Field Kit 156.00

AT396663 Work Lights 712.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

Overall Vehicle:

AT422264 Rear View Camera 1,646.00

AT390721 Vandal Cover Kit 2,164.00

REFERRAL ATTACHMENTS
G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

AT430877 Counterweight, Bottom Mount, 1200 lbs. 3,100.00


Parts are primed only (contact GR Mfg for paint color).

ETN85142 Front Window Guard, Polycarbonate 2,550.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS C-3-ZAXIS 130-5-7
ZAXIS 130-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

REFERRAL ATTACHMENTS Continued...


AT430873 Slant Top Rub Rails 1,645.00
Parts are primed only (contact GR Mfg for paint color).

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS C-3-ZAXIS 130-5-8
ZAXIS 130-5 EXCAVATOR
Continued

THIS PAGE IS INTENTIONALLY LEFT BLANK

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 160 LC-5 -1
ZAXIS 160 LC-5 EXCAVATOR
Equipment for Base Machine

ENGINE: Two Upper Rollers Gauge


*Isuzu AI-4JJ1X - certified to Spring Applied Hydraulic Engine Coolant Temperature
IT4 / Stage IIIB emissions Released Propel Brake Warning Indicator with Audible
121 Net Peak Power (ISO9249) Alarm
Turbocharger UPPER STRUCTURE: Engine Oil Pressure Warning
Electronic Engine Control Unit *Right, Left, and Counterweight Indicator with Audible Alarm
Auto-Idle System Mirrors(3) Fuel Gauge with Low Fuel
Antifreeze Protection to -34F Toolbox Indicator
(-37C) Vandal Locks for: Work Mode Indicator
Enclosed Fan Guard Cab Door Auto Idle Indicator
Dual Element Dry-type Air Filter Service Doors Alternator Charge Indicator
with Restriction Indicator Fuel Cap Air Filter Restriction
Full Flow Oil Filter Tool Box Indicator
Double Fuel Filter Counterweight, 7,077 lbs. (3,210 Fault Code Alert Indicator
Water Separator kg) Check Engine Indicator
*Underhood Diesel Particulate Work Lights: Wiper Mode Indicator
Filter with Curved Exhaust One Mounted on Frame Work Lights On Indicator
Side by Side by Side Radiator, One Mounted on Boom Fuel Rate Display
Oil Cooler, Intercooler with Remote Mounted Engine Oil and Clock
Dust Net Fuel Filters Hour Meter
Glow Plug Start Aid Mode Selection:
50-Amp Alternator - 24 Volt FRONT ATTACHMENT: One Work Mode
500 Hour Engine Oil Change Oil Impregnated Bushings Three Power Modes
Interval Reinforced Resin Thrust Plates Numerous Attachment Modes
Engine Oil Drain Coupler Tungsten Carbide Thermal Coating Auto-Climate Control/Air
70% (35 degree) Off Level on arm to Bucket Joint Conditioner, Heater with
Capability Centralized Lubrication System Pressurizer
Isolation Mounted Dirt Seals on Bucket Pins AM-FM Radio
Less Boom Machine Information Center (MIC)
HYDRAULICS: Less Arm Windshield Wiper/Washer with
Open Center, Load Sensing with Less Bucket Intermittent Speed
Variable Displacement Pumps 12V-60W, 5 Amp Cell Phone Power
Hydraulic Pilot Controls OPERATOR'S STATION: Outlet
Axial Piston Swing Motor ZXLink Ultimate Machine 2 In. Retractable Seat Belt
Multiple Wet Disk Swing Brake Monitoring System w/ 3-year Tinted Safety Glass
Auxiliary Valve Section Message Service (Available in Hot/Cold Box Compartment
Adjustable Flow for Attachments United States and Canada only) Horn
Through Monitor Adjustable Control Positions Two Cup Holders
Boom and Arm Reduced Drift (Levers to Seat, Seat to Pedals) Interior Light
Valves 4" Arm Rests Attached to Side Coat Hook
Power Boost Consoles Floor Mat
Auto Power Lift Pilot Control Shut-Off Lever Motion Alarm with Cancel Switch
Hydraulic Tank Site Gauge Short Stroke, Low Effort Pilot Transparent Tinted Roof Hatch
5,000 Hour Hydraulic Oil Change Levers with Sunshade
Interval Switches for Auxiliary Hydraulic Four Fluid-Filled Elastic Mounts
Control on RH Pilot Lever Easy Access Air Conditioning
UNDERCARRIAGE: Deluxe Adjustable Cloth Seat Filter
Two Speed Propel with Auto-Shift with Suspension, Reclining
Axial Piston Propel Motors Backrest, Headrest, and
Propel Motor Shields Adjustable Lumbar Support
Planetary Final Drives Multifunction, Color LCD Monitor
Sealed Track Chain System with:
Front and Center Track Guides Diagnostic Capability
Provisions for Tie Downs Systems Monitoring Capability
X-Frame Car Body Multiple Language Capability
Hydraulic Track Adjuster Maintenance Tracking
Eight Lower Rollers Engine Coolant Temperature

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B Kernersville, North Carolina for Complete Machine.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 160 LC-5 -2
ZAXIS 160 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

BASE MACHINE Continued...


05W0FF ZAXIS 160 LC-5 EXCAVATOR 192,144.00

MACHINE CONNECTIVITY
Machine connectivity functions require cellular coverage. Usage of ZXLink System requires
customer's acceptance of the terms of the John Deere Telematics System Contract.

Option availability limited by specific geographical regions. Please refer to region specific price
pages for appropriate ordering codes.

1700 ZXLink Ultimate Cellular for the Americas, excluding Costa Rica In Base Price
Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway
(MTG), and ZXLink Ultimate activation.

Includes 3 year subscription. Annual subscription renewal required after 3 years for continued
functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to
www.StellarSupport.com to renew or update ZXLink subscriptions.

1741 No ZXLink Ultimate No Charge

TRACK SHOES
3200 600 mm (24 In.) Triple Semi-Grouser Shoes In Base Price
Recommended for rocky terrain, hard ground and stumps.

3250 700 mm (28 In.) Triple Semi-Grouser Shoes 1,119.00


Recommended for general conditions and soft terrain.

SEATS
4125 Seat, Standard Mechanical In Base Price

4130 Seat, Heated Air-Suspension 785.00

BOOM
6801 Less Boom In Base Price
Excludes Arm Cylinder, Boom Cylinders and Plumbing on Boom.
Includes Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins.
Requires code 7001, "Less Arm".
The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is
recommended

6835 One Piece Boom with Arm Cylinder and Plumbing 15,905.00

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price
Hydraulic Filter Indicator Recommended.

7115 2.6 M (8 ft. 6 in.) Arm with Bucket Cylinder and Linkage 10,831.00

7180 3.1 M (10 ft. 2 In.) Arm with Bucket Cylinder and Linkage 12,369.00

AUXILIARY HYDRAULICS
7401 Less Auxiliary Hydraulics In Base Price

7420 Auxiliary High-Flow Hydraulic Lines for 2.6 M Arm w/ 2-Way Foot Controller 6,767.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 160 LC-5 -3
ZAXIS 160 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

AUXILIARY HYDRAULICS Continued...

7430 Auxiliary High-Flow Hydraulic Lines for 3.1 M Arm w/ 2-Way Foot Controller 6,919.00

7440 Auxiliary High-Flow Hydraulic Lines Only for 2.6 M Arm 4,747.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

7450 Auxiliary High-Flow Hydraulic Lines Only for 3.1 M Arm 4,899.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

BUCKETS
8001 Less Buckets In Base Price
Includes bucket mounting pins.

8420 30 In. (762 mm), 0.65 Yd3 (0.50 M3) Heavy-Duty Bucket 4,079.00
Includes Four (4) Esco Super-V EV29SYL Teeth

8430 36 In. (914 mm), 0.81 Yd3 (0.62 M3) Heavy-Duty Bucket 5,497.00
Includes Five (5) Esco Super-V EV29SYL Teeth

8440 42 In. (1067 mm) 0.99 Yd3 (0.76 M3), Heavy-Duty Bucket 5,750.00
Includes Five (5) Esco Super-V EV29SYL Teeth

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9010 Boom Cylinders with Plumbing to Main Frame 5,959.00
Requires 6801, Less Boom, and Code 7001, Less Arm.

9150 Light Package 727.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

9500 Mechanical Control-Pattern Selector 1,333.00

9600 Rear View Camera 1,745.00

9909 Non-Export Rust Preventive Coating 246.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 160 LC-5 -4
ZAXIS 160 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

OPTIONAL EQUIPMENT--ORDER AS DESIRED Continued...


Machine Information Center, Standard
Machine Information Center (MIC) kits can be ordered using the Technical Information Web
Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC.
MIC Download is used for downloading MIC controller only using an approved PDA. Customer then
transfers information to PC for viewing stored information. There are 2 types of kits available for
customers:
1. Complete MIC for Customer Download - Includes PDA, Software and Cables
2. Update MIC for Customer Download - Includes only download cable and latest software
Technical support for the Customer MIC program is the responsibility of the selling dealer.
Technical support for using the Technical Information Web Bookstore can be obtained by calling
1-866-213-3373.

Machine Information Center, PLUS


Machine Information Center (MIC) kits can be ordered using the Technical Information Web
Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC.
MIC_Plus is for certain customers that would like the ability to perform their own diagnostics as well
as downloading MIC data using an approved PDA. This software is not available directly to
customers and Service Department should be advised before providing MIC_Plus to customers. There
are 2 types of MIC_Plus kits available:
1. Complete MIC_Plus (Customer Diagnostics) - Includes PDA, Software and Cables
2. Update MIC_Plus (Customer Diagnostics) - Includes only Diagnostics cable and latest software
Technical support for the Customer MIC program is the responsibility of the selling dealer. Technical
support for using the Technical Information Web Bookstore can be obtained by calling
1-866-213-3373.

ZXLINK Machine Monitoring System Standard


ZXLINK Machine Monitoring System Standard

The configurator does not automatically order and add ZXLINK to the Machine Quote.
Need to MANUALLY add ZXLINK price to Machine Quote.
Click on (ZXLINK Machine Monitoring System) Hyperlink above to access ZXLINK information
page.
Only for use in the United States and Canada at this time.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Heavy-Duty, High-Capacity:


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT428707 42 In (1067 mm), 1.05 yd3 (.80 M3) Heavy-Duty, High-Capacity Bucket 5,881.00
Only available for Unit 20 (Brazil)

AT428706 42 In (1067 mm), 1.05 yd3 (.80 M3) Standard Duty Bucket 5,592.00
Only available for Unit 20 (Brazil)

AT428708 48 In (1219 mm), 1.21 yd3 (.93 M3) Heavy-Duty, High-Capacity Bucket 6,258.00
Only available for Unit 20 (Brazil)

Buckets, Heavy-Duty:
Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 160 LC-5 -5
ZAXIS 160 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...

AT339089 24 In (610 mm), 0.48 yd3 (0.37 M3) Heavy-Duty Bucket 3,620.00
Includes Four (4) Esco Super-V EV29SYL Teeth

AT339091 30 In (762 mm), 0.65 yd3 (0.50 M3) Heavy-Duty Bucket 3,834.00
Includes Four (4) Esco Super-V EV29SYL Teeth

AT339093 36 In (914 mm), 0.81 yd3 (0.62 M3) Heavy-Duty Bucket 4,370.00
Includes Five (5) Esco Super-V EV29SYL Teeth

AT339095 42 In (1067 mm), 0.99 yd3 (0.76 M3) Heavy-Duty Bucket 4,621.00
Includes Five (5) Esco Super-V EV29SYL Teeth

AT351718 48 In (1220 mm), 1.18 yd3 (0.90 M3) Heavy-Duty Bucket 5,228.00

Guards:

AT390802 Cab FOPS Guard 2,533.00


FOPS Level II, ISO 10262 Certified

Hydraulic Couplers:

AT343229 Hydraulic Quick Coupler 7,835.00

AT345608 Installation Charge for Hydraulic Coupler 1,015.00


Installation Charge Order also requires attachment part number, SHIP-TO address for Paladin
Custom Works, AND reference related machine order number.
The related machine order must reference the attachment order number.
Order code available only for Kernersville, North Carolina installations.

Hydraulic Thumb Kits:


Please click on the following link to access the freight rate tables.

AT339844 Deere/Hitachi Hydraulic Thumb Installation 1,871.00


Labor for installation of Deere/Hitachi thumb at Paladin Customworks Kernersville, NC.

AT379644 Hydraulic Thumb Kit, Direct 8,071.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379645 Hydraulic Thumb Kit, Direct for Couplers 8,071.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379646 Hydraulic Thumb Kit, Progressive 10,223.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379647 Hydraulic Thumb Kit, Progressive for Couplers 10,223.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 160 LC-5 -6
ZAXIS 160 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Hydraulics:

AT415229 Auxiliary Hydraulic Lines for 2.6 M Arm 4,331.00

AT415230 Auxiliary Hydraulic Lines for 3.1 M Arm 4,449.00

AT343990 Auxiliary Hydraulics, Attachment Combination Kit 375.00


Requires Auxiliary High-Flow Hydraulic Lines.
Allows for a combination of attachments (i.e. hammer and thumb) to be connected to the high-flow
lines, ready for operation.
Kit includes parts to replace the arm tube of the high-flow hydraulic lines with a short tube and uses
the existing stop valves to shut-off thumb operation when not in use.

AT327652 Control Handle for Auxiliary Hydraulics, Left-Hand 505.00


Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size
excavators.
Requires control solenoid for either 1-way or 2-way auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390742 Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch 913.00
Does not use the monitor for flow control.
Does not require solenoids for auxiliary hydraulics.
Includes foot switch, solenoid, relays, wiring, and hoses.

AT390718 Control Solenoids for 2-Way Auxiliary Hydraulics 768.00


Monitor can be used to control hydraulic flow.
Can be used with either right-hand or left-hand control handle.

AT390739 Foot Control, Two-Way Hydraulics 1,931.00

AT334168 Hydraulic Filter Restriction Indicator Kit 758.00


Installation Instructions T229238.

ETN93716 Mechanical Control Pattern Selector Kit 967.00


Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control
pattern.
Some excavators require additional parts.

AT390776 Single Pedal Propel Kit 2,039.00

Operator Environment:

AT390824 Guard, Lower Front Window ISO Level II 1,028.00

AT390823 Guard, Upper Front Window ISO Level II 772.00

ETN93549 MP3 Player Field Kit 156.00

AT396663 Work Lights 712.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

Overall Vehicle:

AT422263 Rear View Camera 1,646.00

AT390721 Vandal Cover Kit 2,164.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 160 LC-5 -7
ZAXIS 160 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

REFERRAL ATTACHMENTS
G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

AT430878 Counterweight, Bottom Mount, 1500 lbs. 4,426.00


Parts are primed only (contact GR Mfg for paint color).

ETN85142 Front Window Guard, Polycarbonate 2,550.00

AT430874 Slant Top Rub Rails 1,730.00


Parts are primed only (contact GR Mfg for paint color).

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 160 LC-5 -8
ZAXIS 160 LC-5 EXCAVATOR
Continued

THIS PAGE IS INTENTIONALLY LEFT BLANK

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 210 LC-5 -1
ZAXIS 210 LC-5 EXCAVATOR
Equipment for Base Machine

HYDRAULICS: Air Filter Restriction


Open Center, Load Sensing with FRONT ATTACHMENT: Indicator
Variable Displacement Pumps Oil Impregnated Bushings Fault Code Alert Indicator
Hydraulic Pilot Controls Reinforced Resin Thrust Plates Check Engine Indicator
Axial Piston Swing Motor Tungsten Carbide Thermal Coating Wiper Mode Indicator
Multiple Wet Disk Swing Brake on arm to Bucket Joint Work Lights On Indicator
Auxiliary Valve Section Centralized Lubrication System Fuel Rate Display
Adjustable Flow for Attachments Dirt Seals on Bucket Pins Clock
Through Monitor Less Boom Hour Meter
Boom and Arm Reduced Drift Less Arm Mode Selection:
Valves Less Bucket One Work Mode
Power Boost Three Power Modes
Auto Power Lift OPERATOR'S STATION: Numerous Attachment Modes
Hydraulic Tank Site Gauge ZXLink Ultimate Machine Auto-Climate Control/Air
5,000 Hour Hydraulic Oil Change Monitoring System w/ 3-year Conditioner, Heater with
Interval Message Service (Available in Pressurizer
United States and Canada only) AM-FM Radio
UNDERCARRIAGE: Adjustable Control Positions Machine Information Center (MIC)
Two Speed Propel with Auto-Shift (Levers to Seat, Seat to Pedals) Windshield Wiper/Washer with
Axial Piston Propel Motors 4" Arm Rests Attached to Side Intermittent Speed
Propel Motor Shields Consoles 12V-60W, 5 Amp Cell Phone Power
Planetary Final Drives Pilot Control Shut-Off Lever Outlet
Sealed Track Chain Short Stroke, Low Effort Pilot 2 In. Retractable Seat Belt
Front and Center Track Guides Levers Tinted Safety Glass
Provisions for Tie Downs Switches for Auxiliary Hydraulic Hot/Cold Box Compartment
X-Frame Car Body Control on RH Pilot Lever Horn
Hydraulic Track Adjuster Deluxe Adjustable Cloth Seat Two Cup Holders
Eight Lower Rollers with Suspension, Reclining Interior Light
Two Upper Rollers Backrest, and Headrest Coat Hook
Spring Applied Hydraulic Multifunction, Color LCD Monitor Floor Mat
Released Propel Brake System with: Motion Alarm with Cancel Switch
Diagnostic Capability Transparent Tinted Roof Hatch
UPPER STRUCTURE: Systems Monitoring Capability with Sunshade
Right and Left Mirrors Multiple Language Capability Four Fluid-Filled Elastic Mounts
Toolbox Maintenance Tracking Easy Access Air Conditioning
Vandal Locks for: Engine Coolant Temperature Filter
Cab Door Gauge
Service Doors Engine Coolant Temperature
Fuel Cap Warning Indicator with Audible
Tool Box Alarm
Counterweight, 10,463 lbs. Engine Oil Pressure Warning
(4,750 kg) Indicator with Audible Alarm
Work Lights: Fuel Gauge with Low Fuel
One Mounted on Frame Indicator
One Mounted on Boom Work Mode Indicator
Remote Mounted Engine Oil and Auto Idle Indicator
Fuel Filters Alternator Charge Indicator

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B Kernersville, North Carolina for Complete Machine.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

05X0FF ZAXIS 210 LC-5 EXCAVATOR 194,751.00

ENGINE
1090 *Isuzu AI-4HK1, Certified to IT4 / Stage IIIB emissions 14,018.00
159 hp Net Peak Power (ISO9249)
Turbocharger
Electronic Engine Control Unit
Auto-Idle System

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 210 LC-5 -2
ZAXIS 210 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ENGINE Continued...
Antifreeze Protection to -34F (-37C)
Enclosed Fan Guard
Dual Element Dry-type Air Filter with Restriction Indicator
Full Flow Oil Filter
Double Fuel Filter
Water Separator
*Underhood Diesel Particulate Filter with Curved Exhaust
Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net
Glow Plug Start Aid
50-Amp Alternator - 24 Volt
500 Hour Engine Oil Change Interval
Engine Oil Drain Coupler
70% (35 degree) Off Level Capability
Isolation Mounted
#Note: For use only in areas where EPA Interim Tier 4/EU Stage IIIB is required.#

1060 Engine, Isuzu CC-6BG1 Meets Tier 2 / Stage II emissions -1,529.00


Isuzu CC-6BG1
Meets Tier 2 / Stage II emissions
159 Net Rated hp (ISO 9249)
Turbocharger
Electronic Engine Control Unit
Auto-Idle System
Antifreeze Protection to -34F (-37C)
Enclosed Fan Guard
Dual Element Dry-type Air Filter with Restriction Indicator
Full Flow Oil Filter
Double Fuel Filter
Water Separator
Underhood Muffler with Curved Exhaust
Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net
Glow Plug Start Aid
50-Amp Alternator - 24 Volt
500 Hour Engine Oil Change Interval
*70% (35 degrees) Off Level Capability
Note: For use in areas where EPA Tier 3/EU Stage IIIA or EPA Interim Tier 4/EU Stage IIIB is not
required.

DECALS / OPERATOR MANUALS


1600 Customer Packet, SII, English No Charge
Not available for Brazil.

1610 Portugese Customer Delivery Packet No Charge

MACHINE CONNECTIVITY
Machine connectivity functions require cellular coverage. Usage of ZXLink System requires
customer's acceptance of the terms of the John Deere Telematics System Contract.

Option availability limited by specific geographical regions. Please refer to region specific price
pages for appropriate ordering codes.

1700 ZXLink Ultimate Cellular for the Americas, excluding Costa Rica In Base Price
Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway
(MTG), and ZXLink Ultimate activation.

Includes 3 year subscription. Annual subscription renewal required after 3 years for continued
functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to
www.StellarSupport.com to renew or update ZXLink subscriptions.

1741 No ZXLink Ultimate No Charge

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 210 LC-5 -3
ZAXIS 210 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

TRACK SHOES
3300 Long Undercarriage with 600 mm (24 In.) Triple Semi-Grouser Shoes -1,636.00
Recommended for rocky terrain, hard ground and stumps.

3310 Short Undercarriage with 600 mm (24 In.) Triple Semi-Grouser Shoes -9,265.00
Recommended for rocky terrain, hard ground and stumps.

3325 Long Undercarriage with 700 mm (28 In.) Triple Semi-Grouser Shoes -919.00
Recommended for general conditions and soft terrain.

3330 Short Undercarriage with 700 mm (28 In.) Triple Semi-Grouser Shoes -8,524.00
Recommended for general conditions and soft terrain.

3350 Long Undercarriage with 800 mm (32 In.) Triple Semi-Grouser Shoes In Base Price
Recommended for extremely soft terrain.

3360 Short Undercarriage with 800 mm (32 In.) Triple Semi-Grouser Shoes -7,627.00
Recommended for extremely soft terrain.

SEATS
4125 Seat, Standard Mechanical In Base Price

4130 Seat, Heated Air-Suspension 785.00

BOOM
6801 Less Boom In Base Price
Excludes Arm Cylinder, Boom Cylinders and Plumbing on Boom.
Includes Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins.
Requires code 7001, "Less Arm".
The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is
recommended

6835 One Piece Boom with Arm Cylinder and Plumbing 22,322.00

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price
Hydraulic Filter Indicator Recommended.

7140 2.42 M (7'11") Arm with Bucket Cylinder and Linkage 12,388.00

7160 2.91 M (9'7") Arm with Bucket Cylinder and Linkage 12,767.00

AUXILIARY HYDRAULICS
7401 Less Auxiliary Hydraulics In Base Price

7420 Auxiliary High-Flow Hydraulic Lines for 2.91 M Arm w/ 2-Way Foot Controller 7,828.00

7430 Auxiliary High-Flow Hydraulic Lines for 2.42 M Arm w/ 2-Way Foot Controller 7,575.00

7440 Auxiliary High-Flow Hydraulic Lines Only for 2.91 M Arm 5,808.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

7450 Auxiliary High-Flow Hydraulic Lines Only for 2.42 M Arm 5,555.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 210 LC-5 -4
ZAXIS 210 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

AUXILIARY HYDRAULICS Continued...


switches. Also order a solenoid kit.

BUCKETS
8001 Less Buckets In Base Price
Includes bucket mounting pins.

8320 36 In. (914 mm) 0.90 Yd3 (0.69 M3) Heavy-Duty Bucket 5,975.00
Includes Five (5) Esco Super-V EV29SYL Teeth

8330 42 In. (1067 mm) 1.09 Yd3 (0.83 M3) Heavy-Duty Bucket 6,363.00
Includes Five (5) Esco Super-V EV29SYL Teeth

8340 48 In. (1219 mm) 1.29 Yd3 (0.99 M3) Heavy-Duty Bucket 6,767.00
Includes Six (6) Esco Super-V EV29SYL Teeth

8410 24 in. (610 mm), 0.56 Yd3 (0.43 M3) Heavy-Duty, High-Capacity Bucket 5,374.00
Includes Four (4) Esco Super-V EV29SYL Teeth

8420 36 In. (914 mm) 0.97 Yd3 (0.74 M3) Heavy-Duty, High-Capacity Bucket 6,663.00
Includes Five (5) Esco Super-V EV29SYL Teeth

8430 42 In. (1067 mm), 1.19 Yd3 (0.91 M3) Heavy-Duty, High-Capacity Bucket 6,933.00
Includes Five (5) Esco Super-V EV29SYL Teeth

8470 42 In (1067 mm), 1.58 yd3 (1.21 M3) Standard Duty Bucket 8,568.00
Only available for Unit 20 (Brazil)

8480 48 In (1219 mm), 1.57 yd3 (1.20 M3) Heavy-Duty, High-Capacity Bucket 8,568.00
Only available for Unit 20 (Brazil) and Unit 28

8490 54 In (1372 mm), 1.77 yd3 (1.35 M3) Heavy-Duty, High-Capacity Bucket 8,811.00
Only available for Unit 20 (Brazil) and Unit 28

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9010 Boom Cylinders with Plumbing to Main Frame 7,959.00
Requires 6801, Less Boom, and Code 7001, Less Arm.

9150 Light Package 727.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

9400 Tropical Doors, Radiator-Side and Pump-Side 379.00

9500 Mechanical Control-Pattern Selector 1,333.00

9600 Rear View Camera 1,745.00

9803 Special Export Preperation-- Do not install front for shipping No Charge
For Export Containerization

9909 Non-Export Rust Preventive Coating 264.00

9700 Chrome Exhaust 407.00


ZXLINK Machine Monitoring System Standard
ZXLINK Machine Monitoring System Standard

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 210 LC-5 -5
ZAXIS 210 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

OPTIONAL EQUIPMENT--ORDER AS DESIRED Continued...


The configurator does not automatically order and add ZXLINK to the Machine Quote.
Need to MANUALLY add ZXLINK price to Machine Quote.
Click on (ZXLINK Machine Monitoring System) Hyperlink above to access ZXLINK information
page.
Only for use in the United States and Canada at this time.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Heavy-Duty, High-Capacity:


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339139 24 In (610 mm), 0.56 yd3 (0.43 M3) Heavy-Duty, High-Capacity Bucket 4,701.00
Includes Four (4) Esco Super-V EV29SYL Teeth

AT339141 30 In (762 mm), 0.76 yd3 (0.58 M3) Heavy-Duty, High-Capacity Bucket 5,004.00
Includes Four (4) Esco Super-V EV29SYL Teeth

AT339143 36 In (914 mm), 0.97 yd3 (0.74 M3) Heavy-Duty, High-Capacity Bucket 5,951.00
Includes Five (5) Esco Super-V EV29SYL Teeth

AT339145 42 In (1067 mm), 1.19 yd3 (0.91 M3) Heavy-Duty, High-Capacity Bucket 6,202.00
Includes Five (5) Esco Super-V EV29SYL Teeth

AT428718 42 In (1067 mm), 1.58 yd3 (1.21 M3) Standard Duty Bucket 7,664.00
Only available for Unit 20 (Brazil)

AT339147 48 In (1219 mm), 1.39 yd3 (1.06 M3) Heavy-Duty, High-Capacity Bucket 6,722.00

AT428719 48 In (1219 mm), 1.57 yd3 (1.20 M3) Heavy-Duty, High-Capacity Bucket 7,664.00
Only available for Unit 20 (Brazil) and 28 (LAT)

AT428720 54 In (1372 mm), 1.77 yd3 (1.35 M3) Heavy-Duty, High-Capacity Bucket 7,894.00
Only available for Unit 20 (Brazil)

Buckets, Heavy-Duty:
Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339129 24 In (610 mm), 0.52 yd3 (0.40 M3) Heavy-Duty Bucket 4,437.00
Includes Four (4) Esco Super-V EV29SYL Teeth

AT339131 30 In (762 mm), 0.71 yd3 (0.54 M3) Heavy-Duty Bucket 4,523.00
Includes Four (4) Esco Super-V EV29SYL Teeth

AT339133 36 In (914 mm), 0.90 yd3 (0.69 M3) Heavy-Duty Bucket 4,851.00
Includes Five (5) Esco Super-V EV29SYL Teeth

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 210 LC-5 -6
ZAXIS 210 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT339135 42 In (1067 mm), 1.09 yd3 (0.83 M3) Heavy-Duty Bucket 5,698.00
Includes Five (5) Esco Super-V EV29SYL Teeth

AT339137 48 In (1219 mm), 1.29 yd3 (0.99 M3) Heavy-Duty Bucket 6,089.00
Includes Six (6) Esco Super-V EV29SYL Teeth

Guards:

AT390802 Cab FOPS Guard 2,533.00


FOPS Level II, ISO 10262 Certified

Hydraulic Couplers:

AT343230 Hydraulic Quick Coupler 8,412.00

Hydraulic Thumb Kits:


Please click on the following link to access the freight rate tables.

AT339844 Deere/Hitachi Hydraulic Thumb Installation 1,871.00


Labor for installation of Deere/Hitachi thumb at Paladin Customworks Kernersville, NC.

AT379648 Hydraulic Thumb Kit, Direct 9,068.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379649 Hydraulic Thumb Kit, Direct for Couplers 9,068.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379650 Hydraulic Thumb Kit, Progressive 10,689.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379651 Hydraulic Thumb Kit, Progressive for Couplers 10,689.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

Hydraulics:

AT300477 Anti-Drift Valve with Plumbing and Hardware, Arm Cylinder 3,009.00

AT390761 Auxilary High-Flow Lines for 2.42 M Arm 5,050.00


Installation Instructions T227160

AT390760 Auxiliary High Flow Lines for 2.9 M Arm 5,194.00


Installation Instructions T227160.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 210 LC-5 -7
ZAXIS 210 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT343990 Auxiliary Hydraulics, Attachment Combination Kit 375.00
Requires Auxiliary High-Flow Hydraulic Lines.
Allows for a combination of attachments (i.e. hammer and thumb) to be connected to the high-flow
lines, ready for operation.
Kit includes parts to replace the arm tube of the high-flow hydraulic lines with a short tube and uses
the existing stop valves to shut-off thumb operation when not in use.

AT340288 Boom Cylinder Anti-Drift Valve with Plumbing and Hardware 3,014.00
Installation Instructions T229721.

AT327652 Control Handle for Auxiliary Hydraulics, Left-Hand 505.00


Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size
excavators.
Requires control solenoid for either 1-way or 2-way auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390742 Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch 913.00
Does not use the monitor for flow control.
Does not require solenoids for auxiliary hydraulics.
Includes foot switch, solenoid, relays, wiring, and hoses.

AT390718 Control Solenoids for 2-Way Auxiliary Hydraulics 768.00


Monitor can be used to control hydraulic flow.
Can be used with either right-hand or left-hand control handle.

AT390724 Foot Control, Two-Way Hydraulics 1,931.00

AT334168 Hydraulic Filter Restriction Indicator Kit 758.00


Installation Instructions T229238.

AT393163 Mechanical Control Pattern Selector Kit 967.00


Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control
pattern.
Some excavators require additional parts.

AT390776 Single Pedal Propel Kit 2,039.00

Operator Environment:

AT390824 Guard, Lower Front Window ISO Level II 1,028.00

AT390823 Guard, Upper Front Window ISO Level II 772.00

ETN93549 MP3 Player Field Kit 156.00

AT396663 Work Lights 712.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

Overall Vehicle:

AT421387 Bottom Guards, Upperstructure, Heavy-Duty 2,657.00

AT387779 Rear View Camera 1,646.00

AT390721 Vandal Cover Kit 2,164.00

REFERRAL ATTACHMENTS

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 210 LC-5 -8
ZAXIS 210 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

REFERRAL ATTACHMENTS Continued...


G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

AT430880 Counterweight, Bottom Mount, 2100 lbs. 5,640.00


Parts are primed only (contact GR Mfg for paint color).

ETN85142 Front Window Guard, Polycarbonate 2,550.00

AT430875 Slant Top Rub Rails 1,822.00


Parts are primed only (contact GR Mfg for paint color).

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 180 LC-5 -1
ZAXIS 180 LC-5 EXCAVATOR
Equipment for Base Machine

ENGINE: Two Upper Rollers Engine Coolant Temperature


*Isuzu AI-4JJ1X - certified to Spring Applied Hydraulic Warning Indicator with Audible
IT4 / Stage IIIB emissions Released Propel Brake Alarm
121 Net Peak Power (ISO9249) Engine Oil Pressure Warning
Turbocharger UPPER STRUCTURE: Indicator with Audible Alarm
Electronic Engine Control Unit *Right, Left, and Counterweight Fuel Gauge with Low Fuel
Auto-Idle System Mirrors(3) Indicator
Antifreeze Protection to -34F Toolbox Work Mode Indicator
(-37C) Vandal Locks for: Auto Idle Indicator
Enclosed Fan Guard Cab Door Alternator Charge Indicator
Dual Element Dry-type Air Filter Service Doors Air Filter Restriction
with Restriction Indicator Fuel Cap Indicator
Full Flow Oil Filter Tool Box Fault Code Alert Indicator
Double Fuel Filter Counterweight, 8,620 lbs. (3,910 Check Engine Indicator
Water Separator kg) Wiper Mode Indicator
*Underhood Diesel Particulate Work Lights: Work Lights On Indicator
Filter with Curved Exhaust One Mounted on Frame Fuel Rate Display
Side by Side by Side Radiator, One Mounted on Boom Clock
Oil Cooler, Intercooler with Remote Mounted Engine Oil and Hour Meter
Dust Net Fuel Filters Mode Selection:
Glow Plug Start Aid One Work Mode
50-Amp Alternator - 24 Volt FRONT ATTACHMENT: Three Power Modes
500 Hour Engine Oil Change Oil Impregnated Bushings Numerous Attachment Modes
Interval Reinforced Resin Thrust Plates Auto-Climate Control/Air
Engine Oil Drain Coupler Tungsten Carbide Thermal Coating Conditioner, Heater with
70% (35 degree) Off Level on arm to Bucket Joint Pressurizer
Capability Centralized Lubrication System AM-FM Radio
Isolation Mounted Dirt Seals on Bucket Pins Machine Information Center (MIC)
Less Boom Windshield Wiper/Washer with
HYDRAULICS: Less Arm Intermittent Speed
Open Center, Load Sensing with Less Bucket 12V-60W, 5 Amp Cell Phone Power
Variable Displacement Pumps Outlet
Hydraulic Pilot Controls OPERATOR'S STATION: 2 In. Retractable Seat Belt
Axial Piston Swing Motor ZXLink Ultimate Machine Tinted Safety Glass
Multiple Wet Disk Swing Brake Monitoring System w/ 3-year Hot/Cold Box Compartment
Auxiliary Valve Section Message Service (Available in Horn
Adjustable Flow for Attachments United States and Canada only) Two Cup Holders
Through Monitor Adjustable Control Positions Interior Light
Boom and Arm Reduced Drift (Levers to Seat, Seat to Pedals) Coat Hook
Valves 4" Arm Rests Attached to Side Floor Mat
Power Boost Consoles Motion Alarm with Cancel Switch
Auto Power Lift Pilot Control Shut-Off Lever Transparent Tinted Roof Hatch
Hydraulic Tank Site Gauge Short Stroke, Low Effort Pilot with Sunshade
5,000 Hour Hydraulic Oil Change Levers Four Fluid-Filled Elastic Mounts
Interval Switches for Auxiliary Hydraulic Easy Access Air Conditioning
Control on RH Pilot Lever Filter
UNDERCARRIAGE: Deluxe Adjustable Cloth Seat
Two Speed Propel with Auto-Shift with Suspension, Reclining
Axial Piston Propel Motors Backrest, and Headrest
Propel Motor Shields Multifunction, Color LCD Monitor
Planetary Final Drives System with:
Sealed Track Chain Diagnostic Capability
Front and Center Track Guides Systems Monitoring Capability
Provisions for Tie Downs Multiple Language Capability
X-Frame Car Body Maintenance Tracking
Hydraulic Track Adjuster Engine Coolant Temperature
Eight Lower Rollers Gauge

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B Kernersville, North Carolina for Complete Machine.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 180 LC-5 -2
ZAXIS 180 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

BASE MACHINE Continued...


05Y0FF ZAXIS 180 LC-5 EXCAVATOR 197,031.00

MACHINE CONNECTIVITY
Machine connectivity functions require cellular coverage. Usage of ZXLink System requires
customer's acceptance of the terms of the John Deere Telematics System Contract.

Option availability limited by specific geographical regions. Please refer to region specific price
pages for appropriate ordering codes.

1700 ZXLink Ultimate Cellular for the Americas, excluding Costa Rica In Base Price
Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway
(MTG), and ZXLink Ultimate activation.

Includes 3 year subscription. Annual subscription renewal required after 3 years for continued
functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to
www.StellarSupport.com to renew or update ZXLink subscriptions.

1741 No ZXLink Ultimate No Charge

TRACK SHOES
3310 600 mm (24 In.) Triple Semi-Grouser Shoes In Base Price
Recommended for rocky terrain, hard ground and stumps.

3330 700 mm (28 In.) Triple Semi-Grouser Shoes 1,172.00


Recommended for general conditions and soft terrain.

3360 800 mm (32 In.) Triple Semi-Grouser Shoes 1,664.00


Recommended for extremely soft terrain.

SEATS
4125 Seat, Standard Mechanical In Base Price

4130 Seat, Heated Air-Suspension 785.00

BOOM
6801 Less Boom In Base Price
Excludes Arm Cylinder, Boom Cylinders and Plumbing on Boom.
Includes Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins.
Requires code 7001, "Less Arm".
The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is
recommended

6835 One Piece Boom with Arm Cylinder and Plumbing 16,658.00

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price
Hydraulic Filter Indicator Recommended.

7115 2.7 M (8 ft. 10 in.) Arm with Bucket Cylinder and Linkage 11,424.00

7180 3.2 M (10 ft. 6 In.) Arm with Bucket Cylinder and Linkage 12,955.00

AUXILIARY HYDRAULICS

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 180 LC-5 -3
ZAXIS 180 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

AUXILIARY HYDRAULICS Continued...


7401 Less Auxiliary Hydraulics In Base Price

7420 Auxiliary High-Flow Hydraulic Lines for 2.7 M Arm w/ 2-Way Foot Controller 7,205.00

7430 Auxiliary High-Flow Hydraulic Lines for 3.2 M Arm w/ 2-Way Foot Controller 7,373.00

7440 Auxiliary High-Flow Hydraulic Lines Only for 2.7 M Arm 5,185.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

7450 Auxiliary High-Flow Hydraulic Lines Only for 3.2 M Arm 5,353.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

BUCKETS
8001 Less Buckets In Base Price
Includes bucket mounting pins.

8320 36 In. (914 mm) 0.90 Yd3 (0.69 M3) Heavy-Duty Bucket 6,556.00
Includes Five (5) Esco Super-V EV29SYL Teeth

8330 42 In. (1067 mm) 1.09 Yd3 (0.83 M3) Heavy-Duty Bucket 7,015.00
Includes Five (5) Esco Super-V EV29SYL Teeth

8340 48 In. (1219 mm) 1.29 Yd3 (0.99 M3) Heavy-Duty Bucket 7,425.00
Includes Six (6) Esco Super-V EV29SYL Teeth

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9150 Light Package 727.00
Additional 2 Cab lights, with 1 Right hand Boom Light.

9500 Mechanical Control-Pattern Selector 1,333.00

9600 Rear View Camera 1,745.00

9909 Non-Export Rust Preventive Coating 246.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 180 LC-5 -4
ZAXIS 180 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

OPTIONAL EQUIPMENT--ORDER AS DESIRED Continued...


Machine Information Center, Standard
Machine Information Center (MIC) kits can be ordered using the Technical Information Web
Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC.
MIC Download is used for downloading MIC controller only using an approved PDA. Customer then
transfers information to PC for viewing stored information. There are 2 types of kits available for
customers:
1. Complete MIC for Customer Download - Includes PDA, Software and Cables
2. Update MIC for Customer Download - Includes only download cable and latest software
Technical support for the Customer MIC program is the responsibility of the selling dealer.
Technical support for using the Technical Information Web Bookstore can be obtained by calling
1-866-213-3373.

Machine Information Center, PLUS


Machine Information Center (MIC) kits can be ordered using the Technical Information Web
Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC.
MIC_Plus is for certain customers that would like the ability to perform their own diagnostics as well
as downloading MIC data using an approved PDA. This software is not available directly to
customers and Service Department should be advised before providing MIC_Plus to customers. There
are 2 types of MIC_Plus kits available:
1. Complete MIC_Plus (Customer Diagnostics) - Includes PDA, Software and Cables
2. Update MIC_Plus (Customer Diagnostics) - Includes only Diagnostics cable and latest software
Technical support for the Customer MIC program is the responsibility of the selling dealer. Technical
support for using the Technical Information Web Bookstore can be obtained by calling
1-866-213-3373.

ZXLINK Machine Monitoring System Standard


ZXLINK Machine Monitoring System Standard

The configurator does not automatically order and add ZXLINK to the Machine Quote.
Need to MANUALLY add ZXLINK price to Machine Quote.
Click on (ZXLINK Machine Monitoring System) Hyperlink above to access ZXLINK information
page.
Only for use in the United States and Canada at this time.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Heavy-Duty, High-Capacity:


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339139 24 In (610 mm), 0.56 yd3 (0.43 M3) Heavy-Duty, High-Capacity Bucket 4,701.00
Includes Four (4) Esco Super-V EV29SYL Teeth

AT339141 30 In (762 mm), 0.76 yd3 (0.58 M3) Heavy-Duty, High-Capacity Bucket 5,004.00
Includes Four (4) Esco Super-V EV29SYL Teeth

AT339143 36 In (914 mm), 0.97 yd3 (0.74 M3) Heavy-Duty, High-Capacity Bucket 5,951.00
Includes Five (5) Esco Super-V EV29SYL Teeth

AT428713 42 In (1067 mm), 1.05 yd3 (.80 M3) Heavy-Duty, High-Capacity Bucket 5,881.00
Only available for Unit 20 (Brazil)

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 180 LC-5 -5
ZAXIS 180 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT428712 42 In (1067 mm), 1.05 yd3 (.80 M3) Standard Duty Bucket 5,592.00
Only available for Unit 20 (Brazil)

AT339145 42 In (1067 mm), 1.19 yd3 (0.91 M3) Heavy-Duty, High-Capacity Bucket 6,202.00
Includes Five (5) Esco Super-V EV29SYL Teeth

AT428714 48 In (1219 mm), 1.36 yd3 (1.04 M3) Heavy-Duty, High-Capacity Bucket 6,258.00
Only available for Unit 20 (Brazil)

Buckets, Heavy-Duty:
Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339129 24 In (610 mm), 0.52 yd3 (0.40 M3) Heavy-Duty Bucket 4,437.00
Includes Four (4) Esco Super-V EV29SYL Teeth

AT339131 30 In (762 mm), 0.71 yd3 (0.54 M3) Heavy-Duty Bucket 4,523.00
Includes Four (4) Esco Super-V EV29SYL Teeth

AT339133 36 In (914 mm), 0.90 yd3 (0.69 M3) Heavy-Duty Bucket 4,851.00
Includes Five (5) Esco Super-V EV29SYL Teeth

AT339135 42 In (1067 mm), 1.09 yd3 (0.83 M3) Heavy-Duty Bucket 5,698.00
Includes Five (5) Esco Super-V EV29SYL Teeth

Guards:

AT390802 Cab FOPS Guard 2,533.00


FOPS Level II, ISO 10262 Certified

Hydraulic Couplers:

AT343230 Hydraulic Quick Coupler 8,412.00

Hydraulic Thumb Kits:


Please click on the following link to access the freight rate tables.

AT339844 Deere/Hitachi Hydraulic Thumb Installation 1,871.00


Labor for installation of Deere/Hitachi thumb at Paladin Customworks Kernersville, NC.

AT379648 Hydraulic Thumb Kit, Direct 9,068.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379649 Hydraulic Thumb Kit, Direct for Couplers 9,068.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379650 Hydraulic Thumb Kit, Progressive 10,689.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 180 LC-5 -6
ZAXIS 180 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT379651 Hydraulic Thumb Kit, Progressive for Couplers 10,689.00
Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

Hydraulics:

AT415234 Auxiliary High Flow Lines for 3.2 M Arm 4,822.00

AT415233 Auxiliary High-Flow Lines for 2.7 M Arm 4,690.00

AT343990 Auxiliary Hydraulics, Attachment Combination Kit 375.00


Requires Auxiliary High-Flow Hydraulic Lines.
Allows for a combination of attachments (i.e. hammer and thumb) to be connected to the high-flow
lines, ready for operation.
Kit includes parts to replace the arm tube of the high-flow hydraulic lines with a short tube and uses
the existing stop valves to shut-off thumb operation when not in use.

AT327652 Control Handle for Auxiliary Hydraulics, Left-Hand 505.00


Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size
excavators.
Requires control solenoid for either 1-way or 2-way auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390742 Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch 913.00
Does not use the monitor for flow control.
Does not require solenoids for auxiliary hydraulics.
Includes foot switch, solenoid, relays, wiring, and hoses.

AT390718 Control Solenoids for 2-Way Auxiliary Hydraulics 768.00


Monitor can be used to control hydraulic flow.
Can be used with either right-hand or left-hand control handle.

AT390739 Foot Control, Two-Way Hydraulics 1,931.00

AT334168 Hydraulic Filter Restriction Indicator Kit 758.00


Installation Instructions T229238.

ETN93716 Mechanical Control Pattern Selector Kit 967.00


Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control
pattern.
Some excavators require additional parts.

AT390776 Single Pedal Propel Kit 2,039.00

Operator Environment:

AT390824 Guard, Lower Front Window ISO Level II 1,028.00

AT390823 Guard, Upper Front Window ISO Level II 772.00

ETN93549 MP3 Player Field Kit 156.00

AT396663 Work Lights 712.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 180 LC-5 -7
ZAXIS 180 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Overall Vehicle:

AT422263 Rear View Camera 1,646.00

AT390721 Vandal Cover Kit 2,164.00

REFERRAL ATTACHMENTS
G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

AT430878 Counterweight, Bottom Mount, 1500 lbs. 4,426.00


Parts are primed only (contact GR Mfg for paint color).

ETN85142 Front Window Guard, Polycarbonate 2,550.00

AT430874 Slant Top Rub Rails 1,730.00


Parts are primed only (contact GR Mfg for paint color).

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 180 LC-5 -8
ZAXIS 180 LC-5 EXCAVATOR
Continued

THIS PAGE IS INTENTIONALLY LEFT BLANK

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 1
ZX27U-3 COMPACT EXCAVATOR
Equipment for Base Machine

ENGINE: UNDERCARRIAGE: Horn


Yanmar 3TNV88 3-100 12 in. (300 mm) Rubber Track Hour Meter
(1.64 l) 5 ft. 1 in. (1.55 m) Backfill Instrumentation Lights
26.4 SAE Net HP Blade Monitor System with:
Certified to EPA Interim Propel Motor Shield Engine Preheat Indicator
Tier 4 Emissions Planetary Final Drive Engine Oil Pressure
Antifreeze Two Speed Propel with Auto- Indicator
Single Dry-Type Air Filter matic Shifting Alternator Voltage
Electric Fuel Shutoff Axial Piston Propel Motor Indicator
Fan Guard Fuel Gauge and
Full Flow Oil Filter UPPERSTRUCTURE: Level Indicator
Low Maintenance Battery Zero Tail Swing Configuration Engine Coolant
Fuel Filter & Water Separator 360 Degree Upper Structure Temperature Gauge
Isolation Mounted Rotation and Indicator
Under Hood Muffler Independent Boom Swing Hour Meter
35 Amp Alternator - 12 Volt (72 degree left and Operating Lights Switch
HYDRAULICS: 62 degree right rotation) Operating Lights
Open Center with Two Variable ROPS/FOPS Canopy Indicator
Displacement Pumps and One Toolbox Foldable Propel Pedals and
Fixed Gear Pump Vandal Locks for: Levers
Hydraulic Pilot Controls for Service Doors Two Travel Modes with
Boom, Arm, Bucket, Swing, Work lights: Automatic Shifting and Speed
Boom Swing, Blade, and One Mounted on Canopy Selection Switch
Auxiliary (Cab) Motion Alarm with Cancel
Excavator to Backhoe Control One Mounted on Boom Switch
Pattern Change Valve Counterweight 644 lb. Cupholder
Auxiliary Function Control (292 kg.) 12 Volt Cell Phone Outlet
and Right Hand Lever FRONT ATTACHMENTS:
Boom Swing Foot Control Boom 6 ft. 10 in. (2.10 m)
Axial Piston Swing Motor Arm 3 ft. 10 in. (1.17 m)
Wet Disk Swing Brake Mechanical Quick Coupler
Auxiliary Valve Section
Auxiliary Hydraulic Lines with OPERATOR'S STATION:
Release Under Pressure Vinyl Seat with Fore/Aft
Hydraulic Quick Couplers to Adjustment
End of Boom 2 in. Retractable Seat Belt

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
2870FF ZX27U-3 COMPACT EXCAVATOR 35,595.00

TRACK
3125 12 in. (300 mm) Rubber Track In Base Price

3128 12 in. (300 mm) Steel Track with Triple Semi-Grouser Shoes 712.00

3130 Rubber Crawler Pads 2,793.00


NOTE:
* Shipped from the nearest port
* Factory Hydraulic Clamp installation is not available; dealer-installed only
* Steel track shoes with vulcanized rubber pads bonded to top of shoes.
* Long lead-time item; contact Order Fulfillment for availability

ARM
7110 Standard Arm 3 ft. 10 in. (1.17 m) In Base Price

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 2
ZX27U-3 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ARM Continued...
7120 Long Arm 4 ft. 10 in. (1.47 m) and Extra Counterweight 412 lbs (187 kg) 1,341.00
NOTE:
* Long lead-time item; contact Order Fulfillment for availability
* Extra counterweight extends beyond width of tracks when upper structure is rotated to the side

CANOPY OR CAB
8150 ROPS / FOPS Canopy In Base Price

8185 ROPS / FOPS Cab with Heater & Air Conditioner 6,001.00
Cab is Radio Ready with Speakers, Antenna, Wiring and Mounting.

SEAT
4140 Standard Seat - Vinyl In Base Price
NOTE: Requires ROPS / FOPS Canopy (8150)

4145 Suspension Seat - Vinyl 337.00


NOTE: Requires ROPS / FOPS Canopy (8150)

4150 Suspension Seat - Cloth 366.00


NOTE: Requires ROPS / FOPS Cab with Heater & Air Conditioner (8185)

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets:

AT316552G 12 in. (305 mm) Heavy Duty GREY Bucket; 1.33 cu. 598.00
ft. (0.038 cu. m) (3 Teeth Included)

AT340071G 18 in. (457 mm) Heavy Duty GREY Bucket Bundle 2,357.00
NOTE:
* Bundle includes a quantity of 4 of the same size bucket
* Price includes a 5% discount from individual buckets' prices

AT316553G 18 in. (457 mm) Heavy Duty GREY Bucket; 2.33 cu. 623.00
ft. (0.066 cu. m) (4 Teeth Included)

AT316554G 24 in. (610 mm) Heavy Duty GREY Bucket; 3.29 cu. ft. (0.093 cu. m) (4 Teeth Included) 671.00

AT316555G 30 in. (762 mm) Ditch Cleaning GREY Bucket; 4.4 cu. ft. (0.12 cu. m) (No Teeth) 748.00

Clamps:

AT349585 Hydraulic Clamp, Long Arm - Factory Installation Fee 623.00


NOTE:
* Must also order Hydraulic Clamp
* Cannot be ordered with Rubber Crawler Pads, 3130

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 3
ZX27U-3 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT349584 Hydraulic Clamp, Short Arm - Factory Installation Fee 508.00
NOTE:
* Must also order Hydraulic Clamp
* Cannot be ordered with Rubber Crawler Pads, 3130

AT401411 Hydraulic GREY Clamp Bundle, Short- and Long-Arms 6,391.00


Units prior to SN 255739 also order T213184 (1) and AT317646 (1).
* Bundle includes a quantity of 4 of the same size Hydraulic Clamp
* Price includes a 5% discount from individual clamps' prices
* Works with quick coupler buckets
* If equipped with Long Arm, also requires 2 hydraulic hoses (4661804) from Parts

AT401412 Hydraulic GREY Clamp, Short- and Long-Arms 1,684.00


Units prior to SN 255739 also order T213184 (1) and AT317646 (1)
* Works with quick coupler buckets
* If equipped with Long Arm, also requires 2 hydraulic hoses (4661804) from Parts

Engine:

AT358708 Engine Coolant Heater (110 Volt) See Parts


NOTE:
* Recommended for use in temperatures 32 degrees F / 0 degrees C, and below.
* For model 17, also order Adapter Kit (Part AM882530)

Kits and Accessories:

AT171619 3 in. Retractable Seat Belt See Parts

TY21764 Heavy Duty Battery See Parts


NOTE:
* Recommended for Cold Start climates

4647737 Radio See Parts


NOTE: AM, FM, Clock, and Set-able station buttons

AT323252 Secondary Exit 450.00


NOTE:
* For serial #s 224915 and below
* Only available for cabs with hinged rear window

REFERRAL ATTACHMENTS

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 4
ZX27U-3 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

REFERRAL ATTACHMENTS Continued...


G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

AT318959 Front Protection Screen for Cab (27-60CE) 791.00


NOTE:
* Required when a Hydraulic Breaker is equipped on a ZX27U, ZX35U, or ZX50U Compact
Excavator with a Cab

AT318960 Front Protection Screen for Canopy (27-50 CE) 620.00


NOTE:
* Required when a Hydraulic Breaker is equipped on a ZX27U, ZX35U, or ZX50U Compact
Excavator with a Canopy

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 1
ZX35U-5 COMPACT EXCAVATOR
Equipment for Base Machine

ENGINE: 2 in. Retractable Seat Belt


Yanmar 3TNV88 UNDERCARRIAGE: Horn
(1.64 l) 12 in. (300 mm) Rubber Track Hour Meter
23.3 SAE Net HP 5 ft. 8 in. (1.74 m) Backfill Instrumentation Lights
Certified to EPA Final Blade Monitor System with:
Tier 4 Emissions Propel Motor Shield Engine Preheat Indicator
Antifreeze Planetary Final Drive Engine Oil Pressure
Single Dry-Type Air Filter Two Speed Propel with Auto- Indicator
Electric Fuel Shutoff matic Shifting Alternator Voltage
Fan Guard Axial Piston Propel Motor Indicator
Full Flow Oil Filter Fuel Gauge and
Low Maintenance Battery UPPERSTRUCTURE: Level Indicator
Fuel Filter & Water Separator Zero Tail Swing Configuration Engine Coolant
Isolation Mounted 360 Degree Upper Structure Temperature Gauge
Under Hood Muffler Rotation and Indicator
55 Amp Alternator - 12 Volt Independent Boom Swing Hour Meter
(72 degree left and Operating Lights Switch
HYDRAULICS: 62 degree right rotation) Operating Lights
Closed-Center, Load-Sensing ROPS/FOPS Canopy Indicator
with One Variable Displace- Vandal Locks for: Foldable Propel Pedals and
ment Pump and One Fixed Service Doors Levers
Gear Pump Work lights: Two Travel Modes with
Hydraulic Pilot Controls for One Mounted on Canopy Automatic Shifting and Speed
Boom, Arm, Bucket, Swing, (Cab) Selection Switch
Boom Swing, Blade, and One Mounted on Boom Motion Alarm with Cancel
Auxiliary Counterweight 1190 lb. Switch
Excavator to Backhoe Control (540 kg.) Cupholder
Pattern Change Valve 12 Volt Cell Phone Outlet
Auxiliary Function Control FRONT ATTACHMENTS:
and Right Hand Pilot Lever Boom 8 ft. (2.45 m)
Boom Swing Foot Control Arm 4 ft. 4 in. (1.32 m)
Axial Piston Swing Motor Mechanical Quick Coupler
Wet Disk Swing Brake
Auxiliary Valve Section OPERATOR'S STATION:
Auxiliary Hydraulic Lines with Electronic Throttle Control
Release Under Pressure with Auto Idle
Hydraulic Quick Couplers to Vinyl Seat with Fore/Aft
End of Boom Adjustment

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
2900FF ZX35U-5 COMPACT EXCAVATOR 50,400.29

TRACK
3125 12 in. (300 mm) Rubber Track In Base Price

3128 12 in. (300 mm) Steel Track with Triple Semi-Grouser Shoes 1,035.00

3130 Rubber Crawler Pads 3,029.00


NOTE:
* Shipped from the nearest port
* Factory Hydraulic Clamp installation is not available; dealer-installed only
* Steel track shoes with vulcanized rubber pads bonded to top of shoes.
* Long lead-time item; contact Order Fulfillment for availability

ARM
7110 Standard Arm 4 ft. 4 in. (1.32 m) In Base Price

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 2
ZX35U-5 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ARM Continued...

7120 Long Arm 5 ft. 8 in. (1.72 m) and Extra Counterweight 507 lbs (230 kg) 1,452.00
NOTE:
* Long lead-time item; contact Order Fulfillment for availability
* Extra counterweight extends beyond width of tracks when upper structure is rotated to the side

CANOPY OR CAB
8150 ROPS / FOPS Canopy In Base Price

8185 ROPS / FOPS Cab with Heater & Air Conditioner 6,001.00
Cab is Radio Ready with Speakers, Antenna, Wiring and Mounting.

SEAT
4140 Standard Seat - Vinyl In Base Price
NOTE: Requires ROPS / FOPS Canopy (8150)

4145 Suspension Seat - Vinyl 337.00


NOTE: Requires ROPS / FOPS Canopy (8150)

4150 Suspension Seat - Cloth 366.00


NOTE: Requires ROPS / FOPS Cab with Heater & Air Conditioner (8185)

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9100 Bolt On Cutting Edge 734.21

9555 Angle Blade 2,881.00

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets:

AT316552G 12 in. (305 mm) Heavy Duty GREY Bucket; 1.33 cu. 598.00
ft. (0.038 cu. m) (3 Teeth Included)

AT340073G 18 in. (457 mm) Heavy Duty GREY Bucket Bundle 2,631.00
NOTE:
* Bundle includes a quantity of 4 of the same size bucket
* Price includes a 5% discount from individual buckets' prices

AT316557G 18 in. (457 mm) Heavy Duty GREY Bucket; 2.8 cu. 695.00
ft. (0.080 cu. m) (_ Teeth Included)

AT340075G 24 in. (610 mm) Heavy Duty GREY Bucket Bundle 2,949.00
NOTE:
* Bundle includes a quantity of 4 of the same size bucket
* Price includes a 5% discount from individual buckets' prices

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 3
ZX35U-5 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT316558G 24 in. (610 mm) Heavy Duty GREY Bucket; 4.0 cu. 779.00
ft. (0.11 cu. m) (4 Teeth Included)

AT316559G 30 in. (762 mm) Heavy Duty GREY Bucket; 5.2 cu. ft. (0.14 cu. m) (5 Teeth Included) 851.00

AT316560G 34 in. (863 mm) Ditch Cleaning GREY Bucket; 5.9 916.00
cu. ft. (0.17 cu. m) (No Teeth)

Clamps:

AT349585 Hydraulic Clamp, Long Arm - Factory Installation Fee 623.00


NOTE:
* Must also order Hydraulic Clamp
* Cannot be ordered with Rubber Crawler Pads, 3130

AT349584 Hydraulic Clamp, Short Arm - Factory Installation Fee 508.00


NOTE:
* Must also order Hydraulic Clamp
* Cannot be ordered with Rubber Crawler Pads, 3130

AT386304 Hydraulic GREY Clamp 1,684.00


Works with quick coupler buckets except 12" Heavy Duty.
If equipped with Long Arm (7120), also requires 2 hydraulic hoses (AT321206 & AT324558) from
Parts.
FOR SN PRIOR TO 265350 ALSO ORDER T213184 and AT317646.

AT340080G Hydraulic GREY Clamp Bundle 6,391.00


NOTE:
* Bundle includes a quantity of 4 of the same size Hydraulic Clamp
* Price includes a 5% discount from individual clamps' prices
* Works with quick coupler buckets except 12" Heavy Duty
* If equipped with Long Arm (7120), also requires 2 hydraulic hoses (AT321206) from Parts.

Engine:

AT358708 Engine Coolant Heater (110 Volt) See Parts


NOTE:
* Recommended for use in temperatures 32 degrees F / 0 degrees C, and below.
* For model 17, also order Adapter Kit (Part AM882530)

Kits and Accessories:

AT171619 3 in. Retractable Seat Belt See Parts

FYD00000525 Cab Tilt Tool See Parts

TY21764 Heavy Duty Battery See Parts


NOTE:
* Recommended for Cold Start climates

4647737 Radio See Parts


NOTE: AM, FM, Clock, and Set-able station buttons

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 4
ZX35U-5 COMPACT EXCAVATOR
Continued

THIS PAGE IS INTENTIONALLY LEFT BLANK

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 1
ZX50U-5 COMPACT EXCAVATOR
Equipment for Base Machine

ENGINE: Adjustment
Yanmar 4TNV88 UNDERCARRIAGE: 2 in. Retractable Seat Belt
(2.19 l) 16 in. (400 mm) Rubber Track Horn
35.9 SAE Net HP 6 ft. 7 in. (2.0 m) Backfill Hour Meter
Certified to EPA Final Blade Instrumentation Lights
Tier 4 Emissions Propel Motor Shield Monitor System with:
Antifreeze Planetary Final Drive Engine Preheat Indicator
Single Dry-Type Air Filter Two Speed Propel With Auto- Engine Oil Pressure
Electric Fuel Shutoff matic Shifting Indicator
Fan Guard Axial Piston Propel Motor Alternator Voltage
Full Flow Oil Filter Indicator
Low Maintenance Battery UPPERSTRUCTURE: Fuel Gauge and
Fuel Filter & Water Separator Zero Tail Swing Configuration Level Indicator
Isolation Mounted 360 Degree Upper Structure Engine Coolant
Under Hood Muffler Rotation Temperature Gauge
55 Amp Alternator - 12 Volt Independent Boom Swing and Indicator
(80 degree left and Hour Meter
HYDRAULICS: 60 degree right rotation) Operating Lights Switch
Closed-Center, Load-Sensing ROPS/FOPS Canopy Operating Lights
with One Variable Displace- Toolbox Indicator
ment Pump and One Fixed Vandal Locks for: Foldable Propel Pedals and
Gear Pump Service Doors Levers
Hydraulic Pilot Controls for Work lights: Two Travel Modes with
Boom, Arm, Bucket, Swing, One Mounted on Canopy Automatic Shifting And Speed
Boom Swing, Blade, and (Cab) Selection Switch
Auxiliary One Mounted on Boom Motion Alarm with Cancel
Excavator to Backhoe Control Counterweight 1543 lb. Switch
Pattern Change Valve (700 kg.) Cupholder
Auxiliary Function Control 12 Volt Cell Phone Outlet
and Right Hand Pilot Lever FRONT ATTACHMENTS:
Boom Swing Foot Control Boom 9 ft. 2 in. (2.8 m)
Axial Piston Swing Motor Arm 4 ft. 6 in. (1.38 m)
Wet Disk Swing Brake Mechanical Quick Coupler
Auxiliary Valve Section
Auxiliary Hydraulic Lines with OPERATOR'S STATION:
Release Under Pressure Electronic Throttle Control
Hydraulic Quick Couplers to with Auto Idle
End of Boom Vinyl Seat with Fore/Aft

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
2910FF ZX50U-5 COMPACT EXCAVATOR 67,316.67

TRACK
3125 16 in. (400 mm) Rubber Track In Base Price

3128 16 in. (400 mm) Steel Track with Triple Semi-Grouser Shoes 1,909.00

3130 Rubber Crawler Pads 5,647.00


NOTE:
* Shipped from the nearest port
* Factory Hydraulic Clamp installation is not available; dealer-installed only
* Steel track shoes with vulcanized rubber pads bonded to top of shoes.
* Long lead-time item; contact Order Fulfillment for availability

ARM
7110 Standard Arm 4 ft. 6 in. (1.38 m) In Base Price

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 2
ZX50U-5 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ARM Continued...

7120 Long Arm 5 ft. 7 in. (1.67 m) and Extra Counterweight 474 lbs (215 kg) 1,496.00
NOTE:
* Long lead-time item; contact Order Fulfillment for availability
* Extra counterweight extends beyond width of tracks when upper structure is rotated to the side

CANOPY OR CAB
8150 ROPS / FOPS Canopy In Base Price

8185 ROPS / FOPS Cab with Heater & Air Conditioner 6,001.00
Cab is Radio Ready with Speakers, Antenna, Wiring and Mounting.

SEAT
4140 Standard Seat - Vinyl In Base Price
NOTE: Requires ROPS / FOPS Canopy (8150)

4145 Suspension Seat - Vinyl 337.00


NOTE: Requires ROPS / FOPS Canopy (8150)

4150 Suspension Seat - Cloth 366.00


NOTE: Requires ROPS / FOPS Cab with Heater & Air Conditioner (8185)

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9100 Bolt On Cutting Edge 1,030.26
Can only be ordered for the Angle Blade option

9555 Angle Blade 3,079.00

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets:

AT316561G 12 in. (305 mm) Heavy Duty GREY Bucket; 2.1 cu. 833.00
ft. (0.06 cu. m) (3 Teeth Included)

AT340076G 18 in. (457 mm) Heavy Duty GREY Bucket Bundle 3,476.00
NOTE:
* Bundle includes a quantity of 4 of the same size bucket
* Price includes a 5% discount from individual buckets' prices

AT316562G 18 in. (457 mm) Heavy Duty GREY Bucket; 3.6 cu. 916.00
ft. (0.10 cu. m) (4 Teeth Included)

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 3
ZX50U-5 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT340078G 24 in. (610 mm) Heavy Duty GREY Bucket Bundle 3,910.00
NOTE:
* Bundle includes a quantity of 4 of the same size bucket
* Price includes a 5% discount from individual buckets' prices

AT316563G 24 in. (610 mm) Heavy Duty GREY Bucket; 5.2 cu. 1,031.00
ft. (0.15 cu. m) (4 Teeth Included)

AT316564G 30 in. (762 mm) Heavy Duty GREY Bucket; 6.8 cu. ft. 1,103.00
(0.19 cu. m) (5 Teeth Included)

AT316565G 36 in. (914 mm) Ditch Cleaning GREY Bucket; 8.3 1,144.00
cu. ft. (0.24 cu. m) (No Teeth)

Clamps:

AT349585 Hydraulic Clamp, Long Arm - Factory Installation Fee 623.00


NOTE:
* Must also order Hydraulic Clamp
* Cannot be ordered with Rubber Crawler Pads, 3130

AT349584 Hydraulic Clamp, Short Arm - Factory Installation Fee 508.00


NOTE:
* Must also order Hydraulic Clamp
* Cannot be ordered with Rubber Crawler Pads, 3130

AT340081G Hydraulic GREY Clamp Bundle 6,657.00


NOTE:
* Bundle includes a quantity of 4 of the same size Hydraulic Clamp
* Price includes a 5% discount from individual clamps' prices
* Works with Quick Coupler Buckets except 12" Heavy Duty
* If equipped with Long Arm (7120), also requires 2 hydraulic hoses (AT321206) from Parts.

AT397391 Hydraulic GREY Clamp for (Model 50 SN 275467 above) and (Model 60 SN 280529 above) 1,755.00
Works with Quick Coupler Buckets except 12" Heavy Duty
If equipped with Long Arm (7120), also requires 2 hydraulic hoses (AT321206 and AT363177) from
Parts.

WHEN AT397391 IS ORDERED FOR SERVICE FOR THE 50D, ZX50U2 OR ZX50U3 UNITS
PRIOR TO SERIAL NUMBER 275466 ALSO ORDER AT317647(1) AND T213185 (1).

WHEN AT397391 IS ORDERED FOR SERVICE FOR THE 60D OR ZX60USB3 UNITS PRIOR TO
SERIAL NUMBER 280529 ALSO ORDER AT317647 (1) AND T213185 (1).

Engine:

AT358708 Engine Coolant Heater (110 Volt) See Parts


NOTE:
* Recommended for use in temperatures 32 degrees F / 0 degrees C, and below.
* For model 17, also order Adapter Kit (Part AM882530)

Kits and Accessories:

AT171619 3 in. Retractable Seat Belt See Parts

FYD00000525 Cab Tilt Tool See Parts

TY25803 Heavy Duty Battery See Parts


NOTE:
* Recommended for Cold Start climates

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 4
ZX50U-5 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


4647737 Radio See Parts
NOTE: AM, FM, Clock, and Set-able station buttons

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 1
ZX60USB-5 COMPACT EXCAVATOR
Equipment for Base Machine

ENGINE: UNDERCARRIAGE: Fore/Aft Adjustment


Yanmar 4TNV98 16 in. (400 mm) Rubber Track 2 in. Retractable Seat Belt
(3.3 l) 6 ft. 7 in. (2.0 m) Backfill Horn
53 SAE Net HP Blade Hour Meter
Certified to EPA Final Propel Motor Shield Instrumentation Lights
Tier 4 Emissions Planetary Final Drive Monitor System with:
Antifreeze Two Speed Propel With Auto- Engine Preheat Indicator
Single Dry-Type Air Filter matic Shifting Engine Oil Pressure
Electric Fuel Shutoff Axial Piston Propel Motor Indicator
Fan Guard Alternator Voltage
Full Flow Oil Filter UPPERSTRUCTURE: Indicator
Low Maintenance Battery Reduced Tail Swing Configuration Fuel Gauge and
Fuel Filter & Water Separator 360 Degree Upper Structure Level Indicator
Isolation Mounted Rotation Engine Coolant
Under Hood Muffler Independent Boom Swing Temperature Gauge
55 Amp Alternator - 12 Volt (80 degree left and and Indicator
60 degree right rotation) Hour Meter
HYDRAULICS: ROPS/FOPS/TOPS Cab Operating Lights Switch
Closed-Center, Load-Sensing Toolbox Operating Lights
with One Variable Displace- Vandal Locks for: Indicator
ment Pump and One Fixed Service Doors Foldable Propel Pedals and
Gear Pump Work lights: Levers
Hydraulic Pilot Controls for One Mounted on Canopy Two Travel Modes with
Boom, Arm, Bucket, Swing, (Cab) Automatic Shifting And Speed
Boom Swing, Blade, and One Mounted on Boom Selection Switch
Auxiliary Counterweight 1642 lb. Motion Alarm with Cancel
Excavator to Backhoe Control (745 kg.) Switch
Pattern Change Valve Cupholder
Auxiliary Function Control FRONT ATTACHMENTS: 12 Volt Cell Phone Outlet
and Right Hand Pilot Lever Boom 9 ft. 9 in. (3.0 m)
Boom Swing Foot Control Arm 4 ft. 11 in. (1.5 m)
Axial Piston Swing Motor Mechanical Quick Coupler
Wet Disk Swing Brake
Auxiliary Valve Section OPERATOR'S STATION:
Auxiliary Hydraulic Lines with Air Conditioning and Heat
Release Under Pressure Electronic Throttle Control
Hydraulic Quick Couplers to with Auto Idle
End of Boom Efficiency/Productivity Modes
Cloth Suspension Seat with

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
2920FF ZX60USB-5 COMPACT EXCAVATOR 76,736.06

TRACK
3125 16 in. (400 mm) Rubber Track In Base Price

3128 16 in. (400 mm) Steel Track with Triple Semi-Grouser Shoes 1,909.00

3130 Rubber Crawler Pads 5,647.00


NOTE:
* Shipped from the nearest port
* Factory Hydraulic Clamp installation is not available; dealer-installed only
* Steel track shoes with vulcanized rubber pads bonded to top of shoes.
* Long lead-time item; contact Order Fulfillment for availability

ARM

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 2
ZX60USB-5 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ARM Continued...
7110 Standard Arm 4 ft. 11 in. (1.50 m) In Base Price

7120 Long Arm 6 ft. 1 in. (1.85 m) and Extra Counterweight 573 lbs (260 kg) 1,634.00
NOTE:
* Long lead-time item; contact Order Fulfillment for availability
* Extra counterweight extends beyond width of tracks when upper structure is rotated to the side

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9555 Angle Blade 4,301.00

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets:

AT358512G 18 in. (457 mm) Heavy Duty 4 Tooth GREY Bucket; 5.1 cu. ft. 1,080.00

AT358513G 24 in. (610 mm) Heavy Duty 5 Tooth GREY Bucket; 7.5 cu. ft. 1,216.00

AT358514G 30 in. (762 mm) Heavy Duty 5 Tooth GREY Bucket; 10.0 cu. ft 1,352.00

AT365014G 36 in. (914 mm) Heavy Duty 6 Tooth GREY Bucket; 12.5 cu. ft. 1,408.00

Clamps:

AT349585 Hydraulic Clamp, Long Arm - Factory Installation Fee 623.00


NOTE:
* Must also order Hydraulic Clamp
* Cannot be ordered with Rubber Crawler Pads, 3130

AT349584 Hydraulic Clamp, Short Arm - Factory Installation Fee 508.00


NOTE:
* Must also order Hydraulic Clamp
* Cannot be ordered with Rubber Crawler Pads, 3130

AT397391 Hydraulic GREY Clamp for (Model 50 SN 275467 above) and (Model 60 SN 280529 above) 1,755.00
Works with Quick Coupler Buckets except 12" Heavy Duty
If equipped with Long Arm (7120), also requires 2 hydraulic hoses (AT321206 and AT363177) from
Parts.

WHEN AT397391 IS ORDERED FOR SERVICE FOR THE 50D, ZX50U2 OR ZX50U3 UNITS
PRIOR TO SERIAL NUMBER 275466 ALSO ORDER AT317647(1) AND T213185 (1).

WHEN AT397391 IS ORDERED FOR SERVICE FOR THE 60D OR ZX60USB3 UNITS PRIOR TO
SERIAL NUMBER 280529 ALSO ORDER AT317647 (1) AND T213185 (1).

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 3
ZX60USB-5 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Engine:

AT358708 Engine Coolant Heater (110 Volt) See Parts


NOTE:
* Recommended for use in temperatures 32 degrees F / 0 degrees C, and below.
* For model 17, also order Adapter Kit (Part AM882530)

Kits and Accessories:

AT171619 3 in. Retractable Seat Belt See Parts

FYD00000525 Cab Tilt Tool See Parts

TY25879 Heavy Duty Battery See Parts


NOTE:
* Recommended for Cold Start climates

4647737 Radio See Parts


NOTE: AM, FM, Clock, and Set-able station buttons

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 4
ZX60USB-5 COMPACT EXCAVATOR
Continued

THIS PAGE IS INTENTIONALLY LEFT BLANK

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS ZAXIS 75US-3-1
ZAXIS 75US-3 EXCAVATOR
Equipment for Base Machine

ENGINE: Fuel Cap Work Mode Indicator


Isuzu CC-4JG1 187hp 3.06L # Hydraulic Reservoir Auto Idle Indicator
certified to IT4 / Stage IIIB Toolbox Alternator Charge Indicator
emissions Work lights: Air Filter Restriction
54 SAE Net HP One Mounted on Frame Indicator
Direct Injection One Mounted on Boom Fault Code Alert Indicator
Auxiliary Pump Drive Counterweight 3,040 lbs. (1,380 Check Engine Indicator
Antifreeze Protection to -34 kg) Wiper Mode Indicator
degrees F (-37 degrees C) FRONT ATTACHMENTS: Work Lights On Indicator
Single Dry-Type Air Filter WC Thermal Spraying of Bucket Fuel Rate Display
Electric Fuel Shutoff Joint Clock
Low-Noise Fan with Guard Bucket Clearance adjust Hour Meter
Full Flow Oil Filter mechanism Mode Selection:
Heavy-Duty Low Maintenance Dirt Seal on all Bucket Pins One Work Mode
Batteries (180 Minute Reserve) Monolithically cast bucket link Two Power Modes
Fuel Filter A Numerous Attachment Modes
Isolation Mounted 3.72 M (12 ft. 3 in) One Piece Auto-Climate Control/Air
Radiator/Oil Cooler Trash Screen Boom Conditioner, Heater with
Underhood Muffler with Vertical Less Arm Pressurizer
Exhaust Less Bucket AM-FM Radio
50 Amp Alternator - 24 Volt OPERATOR'S STATION: Machine Information Center (MIC)
Automatic Belt Tension Device Adjustable Control Positions Windshield Wiper/Washer with
Water Separator (Levers to Seat, Seat to Pedals) Intermittent Speed
HYDRAULICS: 4" Arm Rests Attached to Side 12V-60W, 5 Amp Cell Phone Power
Open Center with Two Variable Consoles Outlet
Displacement Pumps Pilot Control Shut-Off Lever 2 In. Retractable Seat Belt
Hydraulic Shut-Off Lever Short Stroke, Low Effort Pilot Tinted Safety Glass
Hydraulic Pilot Controls Levers Hot/Cold Box Compartment
Axial Piston Swing Motor Switches for Auxiliary Hydraulic Horn
Multiple Wet Disk Swing Brake Control on RH Pilot Lever Two Cup Holders
Auxiliary Valve Section Deluxe Adjustable Cloth Seat Interior Light
Boom Reduced-Drift Valves with Suspension, Reclining Coat Hook
UNDERCARRIAGE: Backrest, and Headrest Floor Mat
600 mm (24 In.) Track Shoes Multifunction, Color LCD Monitor Motion Alarm with Cancel Switch
Front Track Guide System with: Transparent Tinted Roof Hatch
Propel Motor Shield Diagnostic Capability with Sunshade
Planetary Final Drive Systems Monitoring Capability Four Fluid-Filled Elastic Mounts
Two-Speed Propel Multiple Language Capability Easy Access Air Conditioning
Axial Piston Propel Motor Maintenance Tracking Filter
Backfill Blade Engine Coolant Temperature
UPPERSTRUCTURE: Gauge
Rearview Mirrors (right, left, Engine Coolant Temperature
and rear) Warning Indicator with Audible
Door, Tropical, Left-Hand Alarm
Toolbox Engine Oil Pressure Warning
Vandal Locks for: Indicator with Audible Alarm
Cab Door Fuel Gauge with Low Fuel
Service Doors Indicator

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B. US/Canadian Port of Entry except where noted.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

3270FF ZAXIS 75US-3 EXCAVATOR 109,328.00

TRACK SHOES
3205 600 mm (24 In.) Triple Semi-Grouser Shoes w/ Blade In Base Price

3265 450 mm (18 In.) Rubber Pads w/ Blade 2,185.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS ZAXIS 75US-3-2
ZAXIS 75US-3 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

TRACK SHOES Continued...

3275 450 mm (18 In.) Continous Rubber Belt w/ Blade 4,920.00


Long lead time required.

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price

7015 1.62 M (5 Ft. 4 In.) Arm Assembly with Bucket Cylinder and Linkage 5,141.00

7060 2.12 M (6 Ft. 11 In.) Arm Assembly with Bucket Cylinder and Linkage 6,378.00

OPTIONAL EQUIPMENT--ORDER AS DESIRED


Non-English Operator's Manuals
Translated Customer Delivery Packets can be ordered using the John Deere Technical Information
Bookstore at http://www.johndeeretechinfo.com at no charge. The Translated Delivery Packets
include the Operator Manual, Decal Kit, Warranty Information Booklet, and Uptime Maintenance
Planner. Search for and order the Translated Delivery Packets by model and language that meets
your customer requirements. A listing of all Translated Delivery Packets available can be found by
selecting Translated Delivery Packets from the Manual Type dropdown list. Technical support is
available by calling 1-866-213-3373.

Machine Information Center, Standard


Machine Information Center (MIC) kits can be ordered using the Technical Information Web
Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC.
MIC Download is used for downloading MIC controller only using an approved PDA. Customer then
transfers information to PC for viewing stored information. There are 2 types of kits available for
customers:
1. Complete MIC for Customer Download - Includes PDA, Software and Cables
2. Update MIC for Customer Download - Includes only download cable and latest software
Technical support for the Customer MIC program is the responsibility of the selling dealer.
Technical support for using the Technical Information Web Bookstore can be obtained by calling
1-866-213-3373.

Machine Information Center, PLUS


Machine Information Center (MIC) kits can be ordered using the Technical Information Web
Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC.
MIC_Plus is for certain customers that would like the ability to perform their own diagnostics as well
as downloading MIC data using an approved PDA. This software is not available directly to
customers and Service Department should be advised before providing MIC_Plus to customers. There
are 2 types of MIC_Plus kits available:
1. Complete MIC_Plus (Customer Diagnostics) - Includes PDA, Software and Cables
2. Update MIC_Plus (Customer Diagnostics) - Includes only Diagnostics cable and latest software
Technical support for the Customer MIC program is the responsibility of the selling dealer. Technical
support for using the Technical Information Web Bookstore can be obtained by calling
1-866-213-3373.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Heavy-Duty:
Buckets come standard with horizontal wear strips.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS ZAXIS 75US-3-3
ZAXIS 75US-3 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT384251 24 In (610 mm), 0.31 yd3 (0.24 M3) Heavy-Duty Bucket 2,565.00
Includes Five (5) Fanggs Teeth (TF23D).

AT384253 30 In (762 mm), 0.41 yd3 (0.31 M3) Heavy-Duty Bucket 2,709.00
Includes Six (6) Fanggs Teeth (TF23D).

AT384255 36 In (914 mm), 0.51 yd3 (0.39 M3) Heavy-Duty Bucket 2,962.00
Includes Seven (7) Fanggs Teeth (TF23D).

Buckets, Ditching:

AT339016 48 In (1219 mm), 0.64 yd3 (0.49 M3) Ditching Bucket 2,335.00

Hydraulics:

AT350233 Auxiliary Hydraulic Lines for 2.12 M Arm 2,034.00

AT356391 Foot Pedal Control Kit for Meterable Two-Way Hydraulics 1,382.00
Recommended: Hydraulic Filter Restriction Indicator Kit
Does not require a solenoid kit.

AT196587 Foot Pedal Switch for 1-Way Control of Auxiliary Valve 505.00
Installation instructions T161995.
Average installation, 1 hour.
For customers who want an auxiliary valve with foot pedal control of attachments that require
1-direction on/off control without metering.
Includes foot switch and wiring harness.

ALSO ORDER:
Hydraulic Filter Restriction Indicator Kit Recommended.
For a complete system, also order the 2-Way Electric Solenoid Valves for Auxiliary Valve and
Auxiliary Hydraulic Lines.

AT334168 Hydraulic Filter Restriction Indicator Kit 758.00


Installation Instructions T229238.

AT356510 Mechanical Pattern Changer 967.00

AT130157 Metric O-Ring Kit See Parts

AT356249 Solenoid Control Kit for 2-Way Auxiliary Hydraulics 770.00


For use with Foot Pedal Switch and/or either joystick control switches

Operator Environment:

AT173678 3 Inch Seat Belt See Parts

AT341067 Cab Window Vandal Protection Kit 2,050.00


The installation instruction number is T230180.

AT337329 Guard, Lower Front Window ISO Level II 720.00


Installation Instructions T227262.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS ZAXIS 75US-3-4
ZAXIS 75US-3 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT336154 Guard, Upper Front Window ISO Level II 960.00
Installation Instructions T227262.
If not installed with the Lower Front Window Guard also order part numbers 4666224 and 4666223.

Overall Vehicle:

AT341089 Oil Sampling Valves 105.00


Installation Instructions T230188.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS ZAXIS 85US-3-1
ZAXIS 85USB-3 EXCAVATOR
Equipment for Base Machine

ENGINE: Hydraulic Reservoir Alternator Charge Indicator


Isuzu CC-4JG1 3.06 L # certified Toolbox Air Filter Restriction
to IT4 / Stage IIIB emissions Work lights: Indicator
54 SAE Net HP One Mounted on Frame Fault Code Alert Indicator
Direct Injection One Mounted on Boom Check Engine Indicator
Auxiliary Pump Drive Counterweight 3,040 lbs. (1,380 Wiper Mode Indicator
Antifreeze Protection to -34 kg) Work Lights On Indicator
degrees F (-37 degrees C) FRONT ATTACHMENTS: Fuel Rate Display
Single Dry-Type Air Filter Independent Swing Boom Clock
Electric Fuel Shutoff WC Thermal Spraying of Bucket Hour Meter
Low-Noise Fan with Guard Joint Mode Selection:
Full Flow Oil Filter Bucket Clearance adjust One Work Mode
Heavy-Duty Low Maintenance mechanism Two Power Modes
Batteries (180 Minute Reserve) Dirt Seal on all Bucket Pins Numerous Attachment Modes
Fuel Filter Monolithically cast bucket link Auto-Climate Control/Air
Isolation Mounted 3.72 M (12 ft. 3 in) One Piece Conditioner, Heater with
Radiator/Oil Cooler Trash Screen Boom Pressurizer
Underhood Muffler with Vertical Less Arm AM-FM Radio
Exhaust Less Bucket Machine Information Center (MIC)
50 Amp Alternator - 24 Volt OPERATOR'S STATION: Windshield Wiper/Washer with
Automatic Belt Tension Device Adjustable Control Position Intermittent Speed
Water Separator (Seat to Pedals) 12V-60W, 5 Amp Cell Phone Power
HYDRAULICS: 3" Arm Rests Attached to Side Outlet
Open Center with Two Variable Consoles 2 In. Retractable Seat Belt
Displacement Pumps Pilot Control Shut-Off Lever Tinted Safety Glass
Hydraulic Shut-Off Lever Short Stroke, Low Effort Pilot Hot/Cold Box Compartment
Hydraulic Pilot Controls Levers Horn
Axial Piston Swing Motor Switches for Auxiliary Hydraulic Two Cup Holders
Multiple Wet Disk Swing Brake Control on RH Pilot Lever Interior Light
Auxiliary Valve Section Deluxe Adjustable Fabric Coat Hook
Boom Reduced-Drift Valves Suspension Seat Floor Mat
UNDERCARRIAGE: Multifunction, Color LCD Monitor Motion Alarm with Cancel Switch
600 mm (24 In.) Track Shoes System with: Transparent Tinted Roof Window
Front Track Guide Diagnostic Capability with Sunshade
Propel Motor Shield Systems Monitoring Capability Four Fluid-Filled Elastic Mounts
Planetary Final Drive Multiple Language Capability Easy Access Air Conditioning
Two-Speed Propel Maintenance Tracking Filter
Axial Piston Propel Motor Engine Coolant Temperature
Backfill Blade Gauge
UPPERSTRUCTURE: Engine Coolant Temperature
Rearview Mirrors (right, left, Warning Indicator with Audible
and rear) Alarm
Door, Tropical, Left-Hand Engine Oil Pressure Warning
Toolbox Indicator with Audible Alarm
Vandal Locks for: Fuel Gauge with Low Fuel
Cab Door Indicator
Service Doors Work Mode Indicator
Fuel Cap Auto Idle Indicator

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B. US/Canadian Port of Entry except where noted.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

3280FF ZAXIS 85USB-3 EXCAVATOR 117,368.00

TRACK SHOES
3205 600 mm (24 In.) Triple Semi-Grouser Shoes w/ Blade In Base Price

3265 450 mm (18 In.) Rubber Pads w/ Blade 2,185.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS ZAXIS 85US-3-2
ZAXIS 85USB-3 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

TRACK SHOES Continued...


Steel track shoes with vulcanized rubber pads bonded to top of shoes.

3275 450 mm (18 In.) Continous Rubber Belt w/ Blade 4,920.00


Long lead time required.

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price

7015 1.62 M (5 Ft. 4 In.) Arm Assembly with Bucket Cylinder and Linkage 5,141.00

7060 2.12 M (6 Ft. 11 In.) Arm Assembly with Bucket Cylinder and Linkage 6,378.00

OPTIONAL EQUIPMENT--ORDER AS DESIRED


Non-English Operator's Manuals
Translated Customer Delivery Packets can be ordered using the John Deere Technical Information
Bookstore at http://www.johndeeretechinfo.com at no charge. The Translated Delivery Packets
include the Operator Manual, Decal Kit, Warranty Information Booklet, and Uptime Maintenance
Planner. Search for and order the Translated Delivery Packets by model and language that meets
your customer requirements. A listing of all Translated Delivery Packets available can be found by
selecting Translated Delivery Packets from the Manual Type dropdown list. Technical support is
available by calling 1-866-213-3373.

Machine Information Center, Standard


Machine Information Center (MIC) kits can be ordered using the Technical Information Web
Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC.
MIC Download is used for downloading MIC controller only using an approved PDA. Customer then
transfers information to PC for viewing stored information. There are 2 types of kits available for
customers:
1. Complete MIC for Customer Download - Includes PDA, Software and Cables
2. Update MIC for Customer Download - Includes only download cable and latest software
Technical support for the Customer MIC program is the responsibility of the selling dealer.
Technical support for using the Technical Information Web Bookstore can be obtained by calling
1-866-213-3373.

Machine Information Center, PLUS


Machine Information Center (MIC) kits can be ordered using the Technical Information Web
Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC.
MIC_Plus is for certain customers that would like the ability to perform their own diagnostics as well
as downloading MIC data using an approved PDA. This software is not available directly to
customers and Service Department should be advised before providing MIC_Plus to customers. There
are 2 types of MIC_Plus kits available:
1. Complete MIC_Plus (Customer Diagnostics) - Includes PDA, Software and Cables
2. Update MIC_Plus (Customer Diagnostics) - Includes only Diagnostics cable and latest software
Technical support for the Customer MIC program is the responsibility of the selling dealer. Technical
support for using the Technical Information Web Bookstore can be obtained by calling
1-866-213-3373.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Heavy-Duty:

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS ZAXIS 85US-3-3
ZAXIS 85USB-3 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT384251 24 In (610 mm), 0.31 yd3 (0.24 M3) Heavy-Duty Bucket 2,565.00
Includes Five (5) Fanggs Teeth (TF23D).

AT384253 30 In (762 mm), 0.41 yd3 (0.31 M3) Heavy-Duty Bucket 2,709.00
Includes Six (6) Fanggs Teeth (TF23D).

AT384255 36 In (914 mm), 0.51 yd3 (0.39 M3) Heavy-Duty Bucket 2,962.00
Includes Seven (7) Fanggs Teeth (TF23D).

Buckets, Ditching:

AT339016 48 In (1219 mm), 0.64 yd3 (0.49 M3) Ditching Bucket 2,335.00

Hydraulics:

AT350366 Auxiliary Hydraulic Lines for both Short & Long Arms 2,387.00
Requires some mounting fabrication.

AT356391 Foot Pedal Control Kit for Meterable Two-Way Hydraulics 1,382.00
Recommended: Hydraulic Filter Restriction Indicator Kit
Does not require a solenoid kit.

AT196587 Foot Pedal Switch for 1-Way Control of Auxiliary Valve 505.00
Installation instructions T161995.
Average installation, 1 hour.
For customers who want an auxiliary valve with foot pedal control of attachments that require
1-direction on/off control without metering.
Includes foot switch and wiring harness.

ALSO ORDER:
Hydraulic Filter Restriction Indicator Kit Recommended.
For a complete system, also order the 2-Way Electric Solenoid Valves for Auxiliary Valve and
Auxiliary Hydraulic Lines.

AT334168 Hydraulic Filter Restriction Indicator Kit 758.00


Installation Instructions T229238.

AT356510 Mechanical Pattern Changer 967.00

AT130157 Metric O-Ring Kit See Parts

AT356249 Solenoid Control Kit for 2-Way Auxiliary Hydraulics 770.00


For use with Foot Pedal Switch and/or either joystick control switches

Operator Environment:

AT173678 3 Inch Seat Belt See Parts

Overall Vehicle:

4712722 Cab FOPS Guard Kit See Parts

AT341089 Oil Sampling Valves 105.00


Installation Instructions T230188.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS ZAXIS 85US-3-4
ZAXIS 85USB-3 EXCAVATOR
Continued

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 250 LC-5 -1
ZAXIS 250 LC-5 EXCAVATOR
Equipment for Base Machine

Fuel Filters Alternator Charge Indicator


HYDRAULICS: Air Filter Restriction
Open Center, Load Sensing with FRONT ATTACHMENT: Indicator
Variable Displacement Pumps Oil Impregnated Bushings Fault Code Alert Indicator
Hydraulic Pilot Controls Reinforced Resin Thrust Plates Check Engine Indicator
Axial Piston Swing Motor Tungsten Carbide Thermal Coating Wiper Mode Indicator
Multiple Wet Disk Swing Brake on arm to Bucket Joint Work Lights On Indicator
Auxiliary Valve Section Centralized Lubrication System Fuel Rate Display
Adjustable Flow for Attachments Dirt Seals on Bucket Pins Clock
Through Monitor Less Boom Hour Meter
Boom and Arm Reduced Drift Less Arm Mode Selection:
Valves Less Bucket One Work Mode
Auto Power Lift Three Power Modes
Hydraulic Tank Site Gauge OPERATOR'S STATION: Numerous Attachment Modes
5,000 Hour Hydraulic Oil Change *ZXLink Ultimate Machine Auto-Climate Control/Air
Interval Monitoring System w/ 3-year Conditioner, Heater with
Message Service Pressurizer
UNDERCARRIAGE: Adjustable Control Positions AM-FM Radio
Two Speed Propel with Auto-Shift (Levers to Seat, Seat to Pedals) Machine Information Center (MIC)
Axial Piston Propel Motors 4" Arm Rests Attached to Side Windshield Wiper/Washer with
Propel Motor Shields Consoles Intermittent Speed
Planetary Final Drives Pilot Control Shut-Off Lever 12V-60W, 5 Amp Cell Phone Power
Sealed Track Chain Short Stroke, Low Effort Pilot Outlet
Front and Center Track Guides Levers 2 In. Retractable Seat Belt
Provisions for Tie Downs Switches for Auxiliary Hydraulic Tinted Safety Glass
X-Frame Car Body Control on RH Pilot Lever Hot/Cold Box Compartment
Hydraulic Track Adjuster Deluxe Adjustable Cloth Seat Horn
Nine Lower Rollers with Suspension, Reclining Two Cup Holders
Two Upper Rollers Backrest, and Headrest Interior Light
Spring Applied Hydraulic Multifunction, Color LCD Monitor Coat Hook
Released Propel Brake System with: Floor Mat
Diagnostic Capability Motion Alarm with Cancel Switch
UPPER STRUCTURE: Systems Monitoring Capability Transparent Tinted Roof Hatch
*Right, Left and Counterweight Multiple Language Capability with Sunshade
Mirrors Maintenance Tracking Four Fluid-Filled Elastic Mounts
Toolbox Engine Coolant Temperature Easy Access Air Conditioning
Vandal Locks for: Gauge Filter
Cab Door Engine Coolant Temperature
Service Doors Warning Indicator with Audible
Tool Box Alarm
Counterweight, 11,270 lbs. Engine Oil Pressure Warning
(5,112 kg) Indicator with Audible Alarm
Work Lights: Fuel Gauge with Low Fuel
One Mounted on Frame Indicator
One Mounted on Boom Work Mode Indicator
Remote Mounted Engine Oil and Auto Idle Indicator

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B Kernersville, North Carolina for Complete Machine.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

4260FF ZAXIS 250 LC-5 EXCAVATOR 225,468.00

ENGINE
1090 Engine, Isuzu AH-4HK Meets IT4 / Stage IIIB emissions 18,818.00
Isuzu AH-4HK
Certified to EPA Interim Tier 4 emissions
188 Net Rated hp (ISO 9249)
Turbocharger
Electronic Engine Control Unit

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 250 LC-5 -2
ZAXIS 250 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ENGINE Continued...
Auto-Idle System
Antifreeze Protection to -34F (-37C)
Enclosed Fan Guard
Dual Element Dry-type Air Filter with Restriction Indicator
Full Flow Oil Filter
Double Fuel Filter
Water Separator
*Underhood Diesel Particulate Filter with Curved Exhaust
Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net
Glow Plug Start Aid
50-Amp Alternator - 24 Volt
500 Hour Engine Oil Change Interval
*70% (35 degrees) Off Level Capability
Note: For use only in areas where EPA Interim Tier 4/EU Stage IIIB is required.

1060 Engine, Isuzu CC-6BG1 Meets Tier 2 / Stage II emissions -1,529.00


Isuzu CC-6BG1
Meets Tier 2 / Stage II emissions
168 Net Rated hp (ISO 9249)
Turbocharger
Electronic Engine Control Unit
Auto-Idle System
Antifreeze Protection to -34F (-37C)
Enclosed Fan Guard
Dual Element Dry-type Air Filter with Restriction Indicator
Full Flow Oil Filter
Double Fuel Filter
Water Separator
Underhood Muffler with Curved Exhaust
Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net
Glow Plug Start Aid
50-Amp Alternator - 24 Volt
500 Hour Engine Oil Change Interval
*70% (35 degrees) Off Level Capability
Note: For use in areas where EPA Tier 3/EU Stage IIIA or EPA Interim Tier 4/EU Stage IIIB is not
required.

DECALS / OPERATOR MANUALS


1600 Customer Packet, SII, English No Charge
Not available for Brazil.

1610 Portugese Customer Delivery Packet No Charge

MACHINE CONNECTIVITY
Machine connectivity functions require cellular coverage. Usage of ZXLink System requires
customer's acceptance of the terms of the John Deere Telematics System Contract.

Option availability limited by specific geographical regions. Please refer to region specific price
pages for appropriate ordering codes.

1700 ZXLink Ultimate Cellular for the Americas, excluding Costa Rica In Base Price
Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway
(MTG), and ZXLink Ultimate activation.

Includes 3 year subscription. Annual subscription renewal required after 3 years for continued
functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to
www.StellarSupport.com to renew or update ZXLink subscriptions.

1741 No ZXLink Ultimate No Charge

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 250 LC-5 -3
ZAXIS 250 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

TRACK SHOES
3325 700 mm (28 In.) Triple Semi-Grouser Shoes -1,194.00
Recommended for general conditions and soft terrain.

3350 800 mm (32 In.) Triple Semi-Grouser Shoes In Base Price


Recommended for extremely soft terrain.

SEATS
4125 Seat, Standard Mechanical In Base Price

4130 Seat, Heated Air-Suspension 785.00

BOOM
6801 Less Boom In Base Price
Excludes Arm Cylinder, Boom Cylinders and Plumbing on Boom.
Includes Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins.
Requires code 7001, "Less Arm".
The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is
recommended

6835 One Piece Boom with Arm Cylinder and Plumbing 23,855.00

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price
Hydraulic Filter Indicator Recommended.

7160 2.96 M (9 Ft. 9 In.) Arm with Bucket Cylinder and Linkage 13,118.00

7180 3.61 M (11 Ft. 10 In.) Arm with Bucket Cylinder and Linkage 15,413.00
Not recommended for impact (hammer) or high density material applications.

AUXILIARY HYDRAULICS
7401 Less Auxiliary Hydraulics In Base Price

7420 Auxiliary High-Flow Hydraulic Lines for 2.96 M Arm w/ 2-Way Foot Controller 8,181.00

7430 Auxiliary High-Flow Hydraulic Lines for 3.61 M Arm w/ 2-Way Foot Controller 8,484.00

7440 Auxiliary High-Flow Hydraulic Lines Only for 2.96 M Arm 6,161.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

7450 Auxiliary High-Flow Hydraulic Lines Only for 3.61 M Arm 6,464.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

BUCKETS
8001 Less Buckets In Base Price
Includes bucket mounting pins.

8320 36 In. (914 mm), 0.97 Yd3 (0.74 M3) Heavy-Duty Bucket 6,574.00
Includes Four (4) Esco Super-V EV39SYL Teeth

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 250 LC-5 -4
ZAXIS 250 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

BUCKETS Continued...

8330 42 In. (1067 mm), 1.19 Yd3 (0.91 M3) Heavy-Duty Bucket 7,440.00
Includes Five (5) Esco Super-V EV39SYL Teeth

8340 48 In. (1219 mm), 1.39 Yd3 (1.06 M3) Heavy-Duty Bucket 7,820.00
Includes Six (6) Esco Super-V EV39SYL Teeth

8350 54 In. (1372 mm), 1.61 Yd3 (1.23 M3) Heavy-Duty Bucket 8,157.00
Includes Six (6) Esco Super-V EV39SYL Teeth

8420 36 In. (914 mm), 1.30 Yd3 (0.99 M3) Heavy-Duty, High-Capacity Bucket 7,725.00
Includes Four (4) Esco Super-V EV39SYL Teeth

8430 42 In. (1067 mm), 1.59 Yd3 (1.22 M3) Heavy-Duty, High-Capacity Bucket 8,247.00
Includes Five (5) Esco Super-V EV39SYL Teeth

8440 48 In. (1219 mm), 1.88 Yd3 (1.44 M3) Heavy-Duty, High-Capacity Bucket 8,660.00
Includes Six (6) Esco Super-V EV39SYL Teeth

8470 42 In (1067 mm), 1.58 yd3 (1.21 M3) Standard Duty Bucket 10,511.00
Only available for Unit 20 (Brazil)

8480 48 In (1219 mm), 1.57 yd3 (1.20 M3) Heavy-Duty, High-Capacity Bucket 8,684.00
Only available for Unit 20 (Brazil)

8490 54 In (1372 mm), 1.77 yd3 (1.35 M3) Heavy-Duty, High-Capacity Bucket 9,028.00
Only available for Unit 20 (Brazil) and Unit 28

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9010 Boom Cylinders with Plumbing to Main Frame 6,847.00
Requires 6801, Less Boom, and Code 7001, Less Arm.

9150 Light Package 727.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

9400 Tropical Doors, Radiator-Side and Pump-Side 326.00

9500 Mechanical Control-Pattern Selector 1,333.00

9600 Rear View Camera 1,745.00

9700 Chrome Exhaust 420.00

9803 Special Export Preperation-- Do not install front for shipping No Charge
For Export Containerization

9909 Non-Export Rust Preventive Coating 282.00

OPTIONAL MACHINE INFORMATION


Non-English Operator's Manuals
Translated Customer Delivery Packets can be ordered using the John Deere Technical Information
Bookstore at http://www.johndeeretechinfo.com at no charge. The Translated Delivery Packets
include the Operator Manual, Decal Kit, Warranty Information Booklet, and Uptime Maintenance
Planner. Search for and order the Translated Delivery Packets by model and language that meets
your customer requirements. A listing of all Translated Delivery Packets available can be found by
selecting Translated Delivery Packets from the Manual Type dropdown list. Technical support is

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 250 LC-5 -5
ZAXIS 250 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

OPTIONAL MACHINE INFORMATION Continued...


available by calling 1-866-213-3373.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Heavy-Duty, High-Capacity:


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339182 24 In (610 mm), 0.75 yd3 (0.57 M3) Heavy-Duty, High-Capacity Bucket 6,406.00
Includes Three (3) John Deere TK-Series Fanggs Teeth (TK400FD).

AT339186 30 In (762 mm), 1.02 yd3 (0.78 M3) Heavy-Duty, High-Capacity Bucket 6,840.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK400FD).

AT339189 36 In (914 mm), 1.30 yd3 (0.99 M3) Heavy-Duty, High-Capacity Bucket 7,384.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK400FD).

AT339191 42 In (1067 mm), 1.59 yd3 (1.22 M3) Heavy-Duty, High-Capacity Bucket 7,917.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK400FD).

AT428724 48 In (1219 mm), 1.57 yd3 (1.20 M3) Heavy-Duty, High-Capacity Bucket 7,774.00
Only available for Unit 20 (Brazil)

AT339193 48 In (1219 mm), 1.88 yd3 (1.44 M3) Heavy-Duty, High-Capacity Bucket 8,340.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK400FD).

AT428725 54 In (1372 mm), 1.77 yd3 (1.35 M3) Heavy-Duty, High-Capacity Bucket 8,099.00
Only available for Unit 20 (Brazil) and 28 (LAT)

AT428726 54 In (1372 mm), 2.03 yd3 (1.55 M3) Heavy-Duty, High-Capacity Bucket 9,500.00
Only available for Unit 20 (Brazil)

Buckets, Heavy-Duty:
Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339173 36 In (914 mm), 0.97 yd3 (0.74 M3) Heavy-Duty Bucket 6,027.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK450FD)

AT339176 42 In (1067 mm), 1.19 yd3 (0.91 M3) Heavy-Duty Bucket 7,087.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK450FD).

AT339178 48 In (1219 mm), 1.39 yd3 (1.06 M3) Heavy-Duty Bucket 7,483.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK550FD)

AT339180 54 In (1372 mm), 1.61 yd3 (1.23 M3) Heavy-Duty Bucket 7,817.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK550FD)

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 250 LC-5 -6
ZAXIS 250 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Buckets, Side Cutters:

AT342511 Edge Protector Kit 399.00

AT342512 Side-Cutter Kit, 3 inch 485.00

AT342513 Side-Cutter Kit, 6 inch 485.00

Guards:

AT390802 Cab FOPS Guard 2,533.00


FOPS Level II, ISO 10262 Certified

Hydraulic Couplers:

AT343231 Hydraulic Quick Coupler 9,269.00

AT345608 Installation Charge for Hydraulic Coupler 1,015.00


Installation Charge Order also requires attachment part number, SHIP-TO address for Paladin
Custom Works, AND reference related machine order number.
The related machine order must reference the attachment order number.
Order code available only for Kernersville, North Carolina installations.

Hydraulic Thumb Kits:


Please click on the following link to access the freight rate tables.

AT339844 Deere/Hitachi Hydraulic Thumb Installation 1,871.00


Labor for installation of Deere/Hitachi thumb at Paladin Customworks Kernersville, NC.

AT379652 Hydraulic Thumb Kit, Direct 9,149.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379653 Hydraulic Thumb Kit, Direct for Couplers 9,149.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379654 Hydraulic Thumb Kit, Progressive 11,298.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379655 Hydraulic Thumb Kit, Progressive for Couplers 11,298.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

Hydraulics:

AT327659 Anti-Drift Valve with Plumbing and Hardware, Arm Cylinder 2,593.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 250 LC-5 -7
ZAXIS 250 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT343990 Auxiliary Hydraulics, Attachment Combination Kit 375.00
Requires Auxiliary High-Flow Hydraulic Lines.
Allows for a combination of attachments (i.e. hammer and thumb) to be connected to the high-flow
lines, ready for operation.
Kit includes parts to replace the arm tube of the high-flow hydraulic lines with a short tube and uses
the existing stop valves to shut-off thumb operation when not in use.

AT390844 Auxiliary Lines, High-Flow for 2.96 M Arm 5,627.00

AT390845 Auxiliary Lines, High-Flow for 3.61 M Arm 5,916.00

AT300471 Boom Cylinder Anti-Drift Valve with Plumbing and Hardware 3,008.00

AT327652 Control Handle for Auxiliary Hydraulics, Left-Hand 505.00


Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size
excavators.
Requires control solenoid for either 1-way or 2-way auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390742 Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch 913.00
Does not use the monitor for flow control.
Does not require solenoids for auxiliary hydraulics.
Includes foot switch, solenoid, relays, wiring, and hoses.

AT390718 Control Solenoids for 2-Way Auxiliary Hydraulics 768.00


Monitor can be used to control hydraulic flow.
Can be used with either right-hand or left-hand control handle.

AT390797 Foot Control, Two-Way Hydraulics 1,931.00


Hydraulic Flow can be controlled by the monitor setting.
If installing kit without auxiliary hydraulic lines also order the following parts: 4239976, 4208313,
4453063, 4654406, and (3) A852133

AT334168 Hydraulic Filter Restriction Indicator Kit 758.00


Installation Instructions T229238.

AT393163 Mechanical Control Pattern Selector Kit 967.00


Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control
pattern.
Some excavators require additional parts.

AT390776 Single Pedal Propel Kit 2,039.00

AT327836 Two-Pump Combined Flow Piping 1,625.00


For attachments that require additional hydraulic flow.
#Do not use with DPF Load Valve kit ETN92612#

Operator Environment:

AT173678 3 Inch Seat Belt See Parts

AT390824 Guard, Lower Front Window ISO Level II 1,028.00

AT390823 Guard, Upper Front Window ISO Level II 772.00

ETN93549 MP3 Player Field Kit 156.00

AT396663 Work Lights 712.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 250 LC-5 -8
ZAXIS 250 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Overall Vehicle:

AT387779 Rear View Camera 1,646.00

AT421344 Undercovers, Heavy-Duty 3,607.00


Please see the parts catalog for undercover installation layout.

AT390721 Vandal Cover Kit 2,164.00

REFERRAL ATTACHMENTS
G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

ETN87389 Auxilary Counterweight, 2250 lbs.,Bottom Mount 6,440.00


Parts are primed only (contact GR Mfg for paint color).

ETN85142 Front Window Guard, Polycarbonate 2,550.00

AT401260 Guard, Slant Top Rub Rails 1,908.00


Parts are primed only (contact GR Mfg for paint color).

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 290 LC-5 -1
ZAXIS 290 LC-5 EXCAVATOR
Equipment for Base Machine

HYDRAULICS: Fuel Filters Air Filter Restriction


Open Center, Load Sensing with Indicator
Variable Displacement Pumps FRONT ATTACHMENT: Fault Code Alert Indicator
Hydraulic Pilot Controls Oil Impregnated Bushings Check Engine Indicator
Axial Piston Swing Motor Reinforced Resin Thrust Plates Wiper Mode Indicator
Multiple Wet Disk Swing Brake Tungsten Carbide Thermal Coating Work Lights On Indicator
Auxiliary Valve Section on arm to Bucket Joint Fuel Rate Display
Adjustable Flow for Attachments Centralized Lubrication System Clock
Through Monitor Dirt Seals on Bucket Pins Hour Meter
Boom and Arm Reduced Drift Less Boom Mode Selection:
Valves Less Arm One Work Mode
Auto Power Lift Less Bucket Three Power Modes
Hydraulic Tank Site Gauge Numerous Attachment Modes
5,000 Hour Hydraulic Oil Change OPERATOR'S STATION: Auto-Climate Control/Air
Interval *ZXLink Ultimate Machine Conditioner, Heater with
Monitoring System w/ 3-year Pressurizer
UNDERCARRIAGE: Message Service AM-FM Radio
32 In. (800 mm) Triple Grouser Adjustable Control Positions Machine Information Center (MIC)
Shoes (Levers to Seat, Seat to Pedals) Windshield Wiper/Washer with
Two Speed Propel with Auto-Shift 4" Arm Rests Attached to Side Intermittent Speed
Axial Piston Propel Motors Consoles 12V-60W, 5 Amp Cell Phone Power
Propel Motor Shields Pilot Control Shut-Off Lever Outlet
Planetary Final Drives Short Stroke, Low Effort Pilot 2 In. Retractable Seat Belt
Sealed Track Chain Levers Tinted Safety Glass
Front and Center Track Guides Switches for Auxiliary Hydraulic Hot/Cold Box Compartment
Provisions for Tie Downs Control on RH Pilot Lever Horn
X-Frame Car Body Deluxe Adjustable Cloth Seat Two Cup Holders
Hydraulic Track Adjuster with Suspension, Reclining Interior Light
Eight Lower Rollers Backrest, and Headrest Coat Hook
Two Upper Rollers Multi-Function, Color LCD Floor Mat
Spring Applied Hydraulic Monitor System with: Motion Alarm with Cancel Switch
Released Propel Brake Diagnostic Capability Transparent Tinted Roof Hatch
Systems Monitoring Capability with Sunshade
UPPER STRUCTURE: Multiple Language Capability Four Fluid-Filled Elastic Mounts
*Right, Left and Counterweight Maintenance Tracking Easy Access Air Conditioning
Mirrors Engine Coolant Temperature Filter
Toolbox Gauge
Vandal Locks for: Engine Coolant Temperature
Cab Door Warning Indicator with Audible
Service Doors Alarm
Tool Box Engine Oil Pressure Warning
Counterweight, 12813 lbs. (5,812 Indicator with Audible Alarm
kg) Fuel Gauge with Low Fuel
Work Lights: Indicator
One Mounted on Frame Work Mode Indicator
One Mounted on Boom Auto Idle Indicator
Remote Mounted Engine Oil and Alternator Charge Indicator

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B Kernersville, North Carolina for Complete Machine.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

4270FF ZAXIS 290 LC-5 EXCAVATOR 262,434.00

ENGINE
1090 Engine, Isuzu AH-4HK Meets IT4 / Stage IIIB emissions 21,792.00
Isuzu AH-4HK
Certified to EPA Interim Tier 4 emissions
188 Net Rated hp (ISO 9249)
Turbocharger

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 290 LC-5 -2
ZAXIS 290 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ENGINE Continued...
Electronic Engine Control Unit
Auto-Idle System
Antifreeze Protection to -34F (-37C)
Enclosed Fan Guard
Dual Element Dry-type Air Filter with Restriction Indicator
Full Flow Oil Filter
Double Fuel Filter
Water Separator
*Underhood Diesel Particulate Filter with Curved Exhaust
Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net
Glow Plug Start Aid
50-Amp Alternator - 24 Volt
500 Hour Engine Oil Change Interval
*70% (35 degrees) Off Level Capability
Note: For use only in areas where EPA Interim Tier 4/EU Stage IIIB is required.

1060 Engine, Isuzu CC-6BG1 Meets Tier 2 / Stage II emissions -1,529.00


Isuzu CC-6BG1
Meets Tier 2 / Stage II emissions
168 Net Rated hp (ISO 9249)
Turbocharger
Electronic Engine Control Unit
Auto-Idle System
Antifreeze Protection to -34F (-37C)
Enclosed Fan Guard
Dual Element Dry-type Air Filter with Restriction Indicator
Full Flow Oil Filter
Double Fuel Filter
Water Separator
Underhood Muffler with Curved Exhaust
Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net
Glow Plug Start Aid
50-Amp Alternator - 24 Volt
500 Hour Engine Oil Change Interval
*70% (35 degrees) Off Level Capability
Note: For use in areas where EPA Tier 3/EU Stage IIIA or EPA Interim Tier 4/EU Stage IIIB is not
required.

MACHINE CONNECTIVITY
Machine connectivity functions require cellular coverage. Usage of ZXLink System requires
customer's acceptance of the terms of the John Deere Telematics System Contract.

Option availability limited by specific geographical regions. Please refer to region specific price
pages for appropriate ordering codes.

1700 ZXLink Ultimate Cellular for the Americas, excluding Costa Rica In Base Price
Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway
(MTG), and ZXLink Ultimate activation.

Includes 3 year subscription. Annual subscription renewal required after 3 years for continued
functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to
www.StellarSupport.com to renew or update ZXLink subscriptions.

1741 No ZXLink Ultimate No Charge

TRACK SHOES
3325 700 mm (28 In.) Triple Semi-Grouser Shoes -1,249.00
Recommended for general conditions and soft terrain.

3350 800 mm (32 In.) Triple Semi-Grouser Shoes In Base Price


Recommended for extremely soft terrain.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 290 LC-5 -3
ZAXIS 290 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

TRACK SHOES Continued...

SEATS
4125 Seat, Standard Mechanical In Base Price

4130 Seat, Heated Air-Suspension 785.00

BOOM
6801 Less Boom In Base Price
Excludes Arm Cylinder, Boom Cylinders and Plumbing on Boom.
Includes Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins.
Requires code 7001, "Less Arm".
The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is
recommended

6835 One Piece Boom with Arm Cylinder and Plumbing 28,424.00

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price
Hydraulic Filter Indicator Recommended.

7160 3.1 M (10 ft. 2 In.) Arm with Bucket Cylinder and Linkage 14,002.00

7180 3.75 M (12 Ft. 4 In.) Arm with Bucket Cylinder and Linkage 18,424.00
Not recommended for impact (hammer) or high density material applications.

AUXILIARY HYDRAULICS
7401 Less Auxiliary Hydraulics In Base Price

7420 Auxiliary High-Flow Hydraulic Lines for 3.1 M Arm w/ 2-Way Foot Controller 8,867.00

7430 Auxiliary High-Flow Hydraulic Lines for 3.75 M Arm w/ 2-Way Foot Controller 9,090.00

7440 Auxiliary High-Flow Hydraulic Lines Only for 3.1 M Arm 6,847.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

7450 Auxiliary High-Flow Hydraulic Lines Only for 3.75 M Arm 7,070.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

BUCKETS
8001 Less Buckets In Base Price
Includes bucket mounting pins.

8320 36 In. (914 mm), 0.97 Yd3 (0.74 M3) Heavy-Duty Bucket 6,770.00
Includes Four (4) Esco Super-V EV39SYL Teeth

8330 42 In. (1067 mm), 1.19 Yd3 (0.91 M3) Heavy-Duty Bucket 7,661.00
Includes Five (5) Esco Super-V EV39SYL Teeth

8340 48 In. (1219 mm), 1.39 Yd3 (1.06 M3) Heavy-Duty Bucket 8,055.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 290 LC-5 -4
ZAXIS 290 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

BUCKETS Continued...
Includes Six (6) Esco Super-V EV39SYL Teeth

8350 54 In. (1372 mm), 1.61 Yd3 (1.23 M3) Heavy-Duty Bucket 8,401.00
Includes Six (6) Esco Super-V EV39SYL Teeth

8420 36 In. (914 mm), 1.30 Yd3 (0.99 M3) Heavy-Duty, High-Capacity Bucket 7,956.00
Includes Four (4) Esco Super-V EV39SYL Teeth

8430 42 In. (1067 mm), 1.59 Yd3 (1.22 M3) Heavy-Duty, High-Capacity Bucket 8,493.00
Includes Five (5) Esco Super-V EV39SYL Teeth

8440 48 In. (1219 mm), 1.88 Yd3 (1.44 M3) Heavy-Duty, High-Capacity Bucket 8,918.00
Includes Six (6) Esco Super-V EV39SYL Teeth

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9010 Boom Cylinders with Plumbing to Main Frame 7,222.00
Requires 6801, Less Boom, and Code 7001, Less Arm.

9150 Light Package 727.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

9400 Tropical Doors, Radiator-Side and Pump-Side 341.00

9500 Mechanical Control-Pattern Selector 1,333.00

9600 Rear View Camera 1,745.00

9700 Chrome Exhaust 420.00

9803 Special Export Preperation-- Do not install front for shipping No Charge
For Export Containerization

9909 Non-Export Rust Preventive Coating 282.00

OPTIONAL MACHINE INFORMATION


Non-English Operator's Manuals
Translated Customer Delivery Packets can be ordered using the John Deere Technical Information
Bookstore at http://www.johndeeretechinfo.com at no charge. The Translated Delivery Packets
include the Operator Manual, Decal Kit, Warranty Information Booklet, and Uptime Maintenance
Planner. Search for and order the Translated Delivery Packets by model and language that meets
your customer requirements. A listing of all Translated Delivery Packets available can be found by
selecting Translated Delivery Packets from the Manual Type dropdown list. Technical support is
available by calling 1-866-213-3373.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Heavy-Duty, High-Capacity:


Buckets come standard with horizontal wear strips.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 290 LC-5 -5
ZAXIS 290 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339182 24 In (610 mm), 0.75 yd3 (0.57 M3) Heavy-Duty, High-Capacity Bucket 6,406.00
Includes Three (3) John Deere TK-Series Fanggs Teeth (TK400FD).

AT339186 30 In (762 mm), 1.02 yd3 (0.78 M3) Heavy-Duty, High-Capacity Bucket 6,840.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK400FD).

AT339189 36 In (914 mm), 1.30 yd3 (0.99 M3) Heavy-Duty, High-Capacity Bucket 7,384.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK400FD).

AT339191 42 In (1067 mm), 1.59 yd3 (1.22 M3) Heavy-Duty, High-Capacity Bucket 7,917.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK400FD).

AT339193 48 In (1219 mm), 1.88 yd3 (1.44 M3) Heavy-Duty, High-Capacity Bucket 8,340.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK400FD).

Buckets, Heavy-Duty:
Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339173 36 In (914 mm), 0.97 yd3 (0.74 M3) Heavy-Duty Bucket 6,027.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK450FD)

AT339176 42 In (1067 mm), 1.19 yd3 (0.91 M3) Heavy-Duty Bucket 7,087.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK450FD).

AT339178 48 In (1219 mm), 1.39 yd3 (1.06 M3) Heavy-Duty Bucket 7,483.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK550FD)

AT339180 54 In (1372 mm), 1.61 yd3 (1.23 M3) Heavy-Duty Bucket 7,817.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK550FD)

Buckets, Side Cutters:

AT342511 Edge Protector Kit 399.00

AT342512 Side-Cutter Kit, 3 inch 485.00

AT342513 Side-Cutter Kit, 6 inch 485.00

Guards:

AT390802 Cab FOPS Guard 2,533.00


FOPS Level II, ISO 10262 Certified

Hydraulic Couplers:

AT343231 Hydraulic Quick Coupler 9,269.00

AT345608 Installation Charge for Hydraulic Coupler 1,015.00


Installation Charge Order also requires attachment part number, SHIP-TO address for Paladin
Custom Works, AND reference related machine order number.
The related machine order must reference the attachment order number.
Order code available only for Kernersville, North Carolina installations.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 290 LC-5 -6
ZAXIS 290 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Hydraulic Thumb Kits:
Please click on the following link to access the freight rate tables.

AT339844 Deere/Hitachi Hydraulic Thumb Installation 1,871.00


Labor for installation of Deere/Hitachi thumb at Paladin Customworks Kernersville, NC.

AT389951 Hydraulic Thumb Kit, Direct 9,149.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT389949 Hydraulic Thumb Kit, Direct for Couplers 9,149.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379658 Hydraulic Thumb Kit, Progressive 11,298.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379659 Hydraulic Thumb Kit, Progressive for Couplers 11,298.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

Hydraulics:

AT327659 Anti-Drift Valve with Plumbing and Hardware, Arm Cylinder 2,593.00

AT343991 Auxiliary Hydraulics, Attachment Combination Kit 748.00


Requires Auxiliary High-Flow Hydraulic Lines.
Allows for a combination of attachments (i.e. hammer and thumb) to be connected to the high-flow
lines, ready for operation.
Kit includes parts to replace the arm tube of the high-flow hydraulic lines with a short tube and uses
the existing stop valves to shut-off thumb operation when not in use.

AT390849 Auxiliary Lines, High-Flow for 3.1 M Arm 6,204.00

AT390850 Auxiliary Lines, High-Flow for 3.75 M Arm 6,421.00

AT300472 Boom Cylinder Anti-Drift Valve with Plumbing and Hardware 3,008.00

AT327652 Control Handle for Auxiliary Hydraulics, Left-Hand 505.00


Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size
excavators.
Requires control solenoid for either 1-way or 2-way auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390742 Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch 913.00
Does not use the monitor for flow control.
Does not require solenoids for auxiliary hydraulics.
Includes foot switch, solenoid, relays, wiring, and hoses.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 290 LC-5 -7
ZAXIS 290 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT390718 Control Solenoids for 2-Way Auxiliary Hydraulics 768.00
Monitor can be used to control hydraulic flow.
Can be used with either right-hand or left-hand control handle.

AT390797 Foot Control, Two-Way Hydraulics 1,931.00


Hydraulic Flow can be controlled by the monitor setting.
If installing kit without auxiliary hydraulic lines also order the following parts: 4239976, 4208313,
4453063, 4654406, and (3) A852133

AT334168 Hydraulic Filter Restriction Indicator Kit 758.00


Installation Instructions T229238.

AT393163 Mechanical Control Pattern Selector Kit 967.00


Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control
pattern.
Some excavators require additional parts.

AT390776 Single Pedal Propel Kit 2,039.00

AT327836 Two-Pump Combined Flow Piping 1,625.00


For attachments that require additional hydraulic flow.
#Do not use with DPF Load Valve kit ETN92612#

Operator Environment:

AT173678 3 Inch Seat Belt See Parts

AT390824 Guard, Lower Front Window ISO Level II 1,028.00

AT390823 Guard, Upper Front Window ISO Level II 772.00

ETN93549 MP3 Player Field Kit 156.00

AT396663 Work Lights 712.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

Overall Vehicle:

AT387779 Rear View Camera 1,646.00

AT421344 Undercovers, Heavy-Duty 3,607.00


Please see the parts catalog for undercover installation layout.

AT390721 Vandal Cover Kit 2,164.00

REFERRAL ATTACHMENTS
G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 290 LC-5 -8
ZAXIS 290 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

REFERRAL ATTACHMENTS Continued...


Phone: (800)841-8001
Fax: (205)655-8005

ETN87389 Auxilary Counterweight, 2250 lbs.,Bottom Mount 6,440.00


Parts are primed only (contact GR Mfg for paint color).

ETN85142 Front Window Guard, Polycarbonate 2,550.00

AT401260 Guard, Slant Top Rub Rails 1,908.00


Parts are primed only (contact GR Mfg for paint color).

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 350 LC-5 -1
ZAXIS 350 LC-5 EXCAVATOR
Equipment for Base Machine

HYDRAULICS: Fuel Filters Air Filter Restriction


Open Center, Load Sensing with Indicator
Variable Displacement Pumps FRONT ATTACHMENT: Fault Code Alert Indicator
Hydraulic Pilot Controls Oil Impregnated Bushings Check Engine Indicator
Axial Piston Swing Motor Reinforced Resin Thrust Plates Wiper Mode Indicator
Multiple Wet Disk Swing Brake Tungsten Carbide Thermal Coating Work Lights On Indicator
Auxiliary Valve Section on arm to Bucket Joint Fuel Rate Display
Adjustable Flow for Attachments Centralized Lubrication System Clock
Through Monitor Dirt Seals on Bucket Pins Hour Meter
Boom and Arm Reduced Drift Less Boom Mode Selection:
Valves Less Arm One Work Mode
Auto Power Lift Less Bucket Three Power Modes
Hydraulic Tank Site Gauge Numerous Attachment Modes
5,000 Hour Hydraulic Oil Change OPERATOR'S STATION: Auto-Climate Control/Air
Interval *ZXLink Ultimate Machine Conditioner, Heater with
Monitoring System w/ 3-year Pressurizer
UNDERCARRIAGE: Message Service AM-FM Radio
32 In. (800 mm) Triple Grouser Adjustable Control Positions Machine Information Center (MIC)
Shoes (Levers to Seat, Seat to Pedals) Windshield Wiper/Washer with
Two Speed Propel with Auto-Shift 4" Arm Rests Attached to Side Intermittent Speed
Axial Piston Propel Motors Consoles 12V-60W, 5 Amp Cell Phone Power
Propel Motor Shields Pilot Control Shut-Off Lever Outlet
Planetary Final Drives Short Stroke, Low Effort Pilot 2 In. Retractable Seat Belt
Sealed Track Chain Levers Tinted Safety Glass
Three Track Guides Switches for Auxiliary Hydraulic Hot/Cold Box Compartment
Provisions for Tie Downs Control on RH Pilot Lever Horn
X-Frame Car Body Deluxe Adjustable Cloth Seat Two Cup Holders
Hydraulic Track Adjuster with Suspension, Reclining Interior Light
Eight Lower Rollers Backrest, and Headrest Coat Hook
Two Upper Rollers Multi-Function, Color LCD Floor Mat
Spring Applied Hydraulic Monitor System with: Motion Alarm with Cancel Switch
Released Propel Brake Diagnostic Capability Transparent Tinted Roof Hatch
Systems Monitoring Capability with Sunshade
UPPER STRUCTURE: Multiple Language Capability Four Fluid-Filled Elastic Mounts
*Right, Left and Counterweight Maintenance Tracking Easy Access Air Conditioning
Mirrors Engine Coolant Temperature Filter
Toolbox Gauge
Vandal Locks for: Engine Coolant Temperature
Cab Door Warning Indicator with Audible
Service Doors Alarm
Tool Box Engine Oil Pressure Warning
Counterweight, 15,274 lbs. Indicator with Audible Alarm
(6.928 kg) Fuel Gauge with Low Fuel
Work Lights: Indicator
One Mounted on Frame Work Mode Indicator
One Mounted on Boom Auto Idle Indicator
Remote Mounted Engine Oil and Alternator Charge Indicator

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B Kernersville, North Carolina for Complete Machine.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

4280FF ZAXIS 350 LC-5 EXCAVATOR 315,652.00

ENGINE
1090 Engine, Isuzu AH-6HK Meets IT4 / Stage IIIB emissions 26,073.00
Isuzu AH-6HK
Certified to EPA Interim Tier 4 emissions
271 Net Rated hp (ISO 9249)
Turbocharger

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 350 LC-5 -2
ZAXIS 350 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ENGINE Continued...
Electronic Engine Control Unit
Auto-Idle System
Antifreeze Protection to -34F (-37C)
Enclosed Fan Guard
Dual Element Dry-type Air Filter with Restriction Indicator
Full Flow Oil Filter
Double Fuel Filter
Water Separator
*Underhood Diesel Particulate Filter with Curved Exhaust
Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net
Glow Plug Start Aid
50-Amp Alternator - 24 Volt
500 Hour Engine Oil Change Interval
*70% (35 degrees) Off Level Capability
Note: For use only in areas where EPA Interim Tier 4/EU Stage IIIB is required.

1060 Engine, Isuzu AA-6HK1 Meets Tier 2 / Stage II emissions -2,294.00


Isuzu AA-6HK1
Meets Tier 2 / Stage II emissions
237 Net Rated hp (ISO 9249)
Turbocharger
Electronic Engine Control Unit
Auto-Idle System
Antifreeze Protection to -34F (-37C)
Enclosed Fan Guard
Dual Element Dry-type Air Filter with Restriction Indicator
Full Flow Oil Filter
Double Fuel Filter
Water Separator
Underhood Muffler with Curved Exhaust
Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net
Glow Plug Start Aid
50-Amp Alternator - 24 Volt
500 Hour Engine Oil Change Interval
*70% (35 degrees) Off Level Capability
Note: For use in areas where EPA Tier 3/EU Stage IIIA or EPA Interim Tier 4/EU Stage IIIB is not
required.

DECALS / OPERATOR MANUALS


1600 Customer Packet, SII, English No Charge
Not available for Brazil.

1610 Portugese Customer Delivery Packet No Charge

MACHINE CONNECTIVITY
Machine connectivity functions require cellular coverage. Usage of ZXLink System requires
customer's acceptance of the terms of the John Deere Telematics System Contract.

Option availability limited by specific geographical regions. Please refer to region specific price
pages for appropriate ordering codes.

1700 ZXLink Ultimate Cellular for the Americas, excluding Costa Rica In Base Price
Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway
(MTG), and ZXLink Ultimate activation.

Includes 3 year subscription. Annual subscription renewal required after 3 years for continued
functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to
www.StellarSupport.com to renew or update ZXLink subscriptions.

1741 No ZXLink Ultimate No Charge

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 350 LC-5 -3
ZAXIS 350 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

TRACK SHOES
3310 600 mm (24 In.) Triple Semi-Grouser Shoes -1,975.00

3330 700 mm (28 In.) Triple Semi-Grouser Shoes -1,292.00

3320 700 mm (28 In.) Single-Bar, Heavy-Duty Chain and Shoes 8,790.00

3350 800 mm (32 In.) Triple Semi-Grouser Shoes In Base Price

SEATS
4125 Seat, Standard Mechanical In Base Price

4130 Seat, Heated Air-Suspension 785.00

BOOM
6801 Less Boom In Base Price
Excludes Arm Cylinder, Boom Cylinders and Plumbing on Boom.
Includes Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins.
Requires code 7001, "Less Arm".
The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is
recommended

6835 One Piece Boom with Arm Cylinder and Plumbing 28,273.00

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price
Hydraulic Filter Indicator Recommended.

7150 2.66 M (8 Ft. 9 In.) Arm with Bucket Cylinder and Linkage 19,215.00

7222 3.2 M (10 ft. 6 In.) Arm with Bucket Cylinder and Linkage 20,733.00

7267 4.0 M (13 Ft. 1 In.) Arm with Bucket Cylinder and Linkage 22,169.00
Not recommended for impact (hammer) or high density material applications.

AUXILIARY HYDRAULICS
7401 Less Auxiliary Hydraulics In Base Price

7420 Auxiliary High-Flow Hydraulic Lines for 3.2 M Arm w/ 2-Way Foot Controller 9,242.00

7430 Auxiliary High-Flow Hydraulic Lines for 4.0 M Arm w/ 2-Way Foot Controller 9,290.00

7450 Auxiliary High-Flow Hydraulic Lines Only for 3.2 M Arm 7,270.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

7460 Auxiliary High-Flow Hydraulic Lines Only for 4.0 M Arm 7,376.00
Requires a control circuit such as a foot controller or the standard right-hand control handle with (2)
switches. Also order a solenoid kit.

BUCKETS
8001 Less Buckets In Base Price
Includes bucket mounting pins.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 350 LC-5 -4
ZAXIS 350 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

BUCKETS Continued...

8270 60 In. (1524 mm), 2.78 Yd3 (2.13 M3) General-Purpose, High-Capacity Bucket 10,321.00
Includes Seven (7) Hensley-Style Fanggs (TF400)

8340 48 In. (1219 mm), 1.88 Yd3 (1.44 M3) Heavy-Duty Bucket 8,437.00
Includes Six (6) Hensley-Style Fanggs (TF400)

8350 54 In. (1372 mm) 2.18 Yd3 (1.67 M3) Heavy-Duty Bucket 9,279.00
Includes Six (6) Hensley-Style Fanggs (TF400)

8430 42 In. (1067 mm), 1.74 Yd3 (1.33 M3) Heavy-Duty, High-Capacity Bucket 9,061.00
Includes Five (5) Hensley-Style Fanggs (TF400)

8440 48 In. (1219 mm), 2.07 Yd3 (1.58 M3) Heavy-Duty, High-Capacity Bucket 9,719.00
Includes Six (6) Hensley-Style Fanggs (TF400)

8450 54 In. (1373 mm), 2.41 Yd3 (1.84 M3) Heavy-Duty, High-Capacity Bucket 10,202.00
Includes Six (6) Hensley-Style Fanggs (TF400)

8510 54 In (1372 mm), 2.38 yd3 (1.82 M3) Standard Duty Bucket 14,242.00
Only available for Unit 20 (Brazil)

8520 60 In (1524 mm), 2.66 yd3 (2.03 M3) Heavy-Duty, High-Capacity Bucket 15,120.00
Only available for Unit 20 (Brazil)

8530 66 In (1676 mm), 2.85 yd3 (2.18 M3) Heavy-Duty, High-Capacity Bucket 15,466.00
Only available for Unit 20 (Brazil) and Unit 28

8540 66 In (1676 mm), 3.30 yd3 (2.52 M3) Heavy-Duty, High-Capacity Bucket 17,041.00
Only available for Unit 20 (Brazil) and Unit 28

Only available for ME front

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9010 Boom Cylinders with Plumbing to Main Frame 7,115.00
Requires 6801, Less Boom, and Code 7001, Less Arm.

9150 Light Package 727.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

9400 Tropical Doors, Radiator-Side and Pump-Side 348.00

9500 Mechanical Control-Pattern Selector 1,333.00

9600 Rear View Camera 1,745.00

9700 Chrome Exhaust 432.00

9803 Special Export Preperation-- Do not install front for shipping No Charge
For Export Containerization

9909 Non-Export Rust Preventive Coating 300.00

OPTIONAL MACHINE INFORMATION


Non-English Operator's Manuals
Translated Customer Delivery Packets can be ordered using the John Deere Technical Information

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 350 LC-5 -5
ZAXIS 350 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

OPTIONAL MACHINE INFORMATION Continued...


Bookstore at http://www.johndeeretechinfo.com at no charge. The Translated Delivery Packets
include the Operator Manual, Decal Kit, Warranty Information Booklet, and Uptime Maintenance
Planner. Search for and order the Translated Delivery Packets by model and language that meets
your customer requirements. A listing of all Translated Delivery Packets available can be found by
selecting Translated Delivery Packets from the Manual Type dropdown list. Technical support is
available by calling 1-866-213-3373.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, General-Purpose, High-Capacity:


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339215 60 In (1524 mm), 2.78 yd3 (2.13 M3) General-Purpose, High-Capacity Bucket 10,815.00
Includes Seven (7) John Deere TK-Series Fanggs Teeth (TK450FD).

Buckets, Heavy-Duty, High-Capacity:


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339225 36 In (914 mm), 1.41 yd3 (1.08 M3) Heavy-Duty, High-Capacity Bucket 8,809.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK450FD).

AT339227 42 In (1067 mm), 1.74 yd3 (1.33 M3) Heavy-Duty, High-Capacity Bucket 9,441.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK450FD).

AT339230 48 In (1219 mm), 2.07 yd3 (1.58 M3) Heavy-Duty, High-Capacity Bucket 10,158.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK450FD).

AT428731 54 In (1372 mm), 2.38 yd3 (1.82 M3) Standard Duty Bucket 13,026.00
Only available for Unit 20 (Brazil)

AT339232 54 In (1372 mm), 2.41 yd3 (1.84 M3) Heavy-Duty, High-Capacity Bucket 10,692.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK450FD).

AT428732 60 In (1524 mm), 2.66 yd3 (2.03 M3) Heavy-Duty, High-Capacity Bucket 13,856.00
Only available for Unit 20 (Brazil)

AT428733 66 In (1676 mm), 2.85 yd3 (2.18 M3) Heavy-Duty, High-Capacity Bucket 14,182.00
Only available for Unit 20 (Brazil) and 28 (LAT)

AT428734 66 In (1676 mm), 3.30 yd3 (2.52 M3) Heavy-Duty, High-Capacity Bucket 15,670.00
Only available for Unit 20 (Brazil)

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 350 LC-5 -6
ZAXIS 350 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Buckets, Heavy-Duty:
Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339217 36 In (914 mm), 1.30 yd3 (0.99 M3) Heavy-Duty Bucket 7,670.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK450FD)

AT339219 42 In (1067 mm), 1.59 yd3 (1.22 M3) Heavy-Duty Bucket 8,240.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK450FD).

AT339221 48 In (1219 mm), 1.88 yd3 (1.44 M3) Heavy-Duty Bucket 8,760.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK550FD)

AT339223 54 In (1372 mm), 2.18 yd3 (1.67 M3) Heavy-Duty Bucket 9,218.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK550FD)

Buckets, Side Cutters:

AT342511 Edge Protector Kit 399.00

AT342512 Side-Cutter Kit, 3 inch 485.00

AT342513 Side-Cutter Kit, 6 inch 485.00

Guards:

AT390802 Cab FOPS Guard 2,533.00


FOPS Level II, ISO 10262 Certified

Hydraulic Couplers:

AT343232 Hydraulic Quick Coupler 11,100.00

AT345608 Installation Charge for Hydraulic Coupler 1,015.00


Installation Charge Order also requires attachment part number, SHIP-TO address for Paladin
Custom Works, AND reference related machine order number.
The related machine order must reference the attachment order number.
Order code available only for Kernersville, North Carolina installations.

Hydraulic Thumb Kits:


Please click on the following link to access the freight rate tables.

AT339844 Deere/Hitachi Hydraulic Thumb Installation 1,871.00


Labor for installation of Deere/Hitachi thumb at Paladin Customworks Kernersville, NC.

AT379660 Hydraulic Thumb Kit, Direct 10,223.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379661 Hydraulic Thumb Kit, Direct for Couplers 10,223.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 350 LC-5 -7
ZAXIS 350 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT379662 Hydraulic Thumb Kit, Progressive 12,268.00
Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

AT379663 Hydraulic Thumb Kit, Progressive for Couplers 12,268.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

Hydraulics:

AT327659 Anti-Drift Valve with Plumbing and Hardware, Arm Cylinder 2,593.00

AT343991 Auxiliary Hydraulics, Attachment Combination Kit 748.00


Requires Auxiliary High-Flow Hydraulic Lines.
Allows for a combination of attachments (i.e. hammer and thumb) to be connected to the high-flow
lines, ready for operation.
Kit includes parts to replace the arm tube of the high-flow hydraulic lines with a short tube and uses
the existing stop valves to shut-off thumb operation when not in use.

AT419615 Auxiliary Lines, High-Flow for 2.67 M Arm 6,493.00


Includes 1 In. diameter lines from the auxiliary spool in main control valve along the boom ending on
the arm and 1.25 In. return line routed directly to return filter piping for low pressure return. Also
includes 2 relief valves and 2 shutoff valves located on end of arm.
Recommend Hydraulic Filter Restriction Indicator Kit.

AT390855 Auxiliary Lines, High-Flow for 3.2 M Arm 6,637.00


Includes 1 In. diameter lines from the auxiliary spool in main control valve along the boom ending on
the arm and 1.25 In. return line routed directly to return filter piping for low pressure return. Also
includes 2 relief valves and 2 shutoff valves located on end of arm.
Recommend Hydraulic Filter Restriction Indicator Kit.

AT390854 Auxiliary Lines, High-Flow for 4.0 M Arm 6,781.00


Includes 1 In. diameter lines from the auxiliary spool in main control valve along the boom ending on
the arm and 1.25 In. return line routed directly to return filter piping for low pressure return. Also
includes 2 relief valves and 2 shutoff valves located on end of arm.
Recommend Hydraulic Filter Restriction Indicator Kit.

AT300472 Boom Cylinder Anti-Drift Valve with Plumbing and Hardware 3,008.00

AT327652 Control Handle for Auxiliary Hydraulics, Left-Hand 505.00


Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size
excavators.
Requires control solenoid for either 1-way or 2-way auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390742 Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch 913.00
Does not use the monitor for flow control.
Does not require solenoids for auxiliary hydraulics.
Includes foot switch, solenoid, relays, wiring, and hoses.

AT390718 Control Solenoids for 2-Way Auxiliary Hydraulics 768.00


Monitor can be used to control hydraulic flow.
Can be used with either right-hand or left-hand control handle.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 350 LC-5 -8
ZAXIS 350 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT327632 Filter Restriction Indicator 758.00
This kit is recommended when the excavator will be equipped with front attachment such as crushers,
thumbs, hammers, log loaders, etc.
Installation Instruction T229238

AT390798 Foot Control, Two-Way Hydraulics 1,931.00


If ordering for the 470 excavators also order 4659600 and 4659601.
If installing kit without auxiliary hydraulic lines also order the following parts: 4239976, 4208913,
4453063, 4654406, and (3) A852133.

AT390719 Mechanical Control Pattern Selector Kit 967.00


Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control
pattern.
Some excavators require additional parts.

AT390776 Single Pedal Propel Kit 2,039.00

AT358596 Two-Pump Combined Flow Piping 1,625.00


For attachments that require additional hydraulic flow.
#Do not use with DPF Load Valve kit ETN92604#

Operator Environment:

AT173678 3 Inch Seat Belt See Parts

AT390824 Guard, Lower Front Window ISO Level II 1,028.00

AT390823 Guard, Upper Front Window ISO Level II 772.00

ETN93549 MP3 Player Field Kit 156.00

AT396663 Work Lights 712.00


Additional 2 Cab lights, with 1 Right hand Boom Light.

Overall Vehicle:

AT387779 Rear View Camera 1,646.00

AT420419 Undercovers, Heavy-Duty 3,902.00


Please see the parts catalog for undercover installation layout.

AT390721 Vandal Cover Kit 2,164.00

REFERRAL ATTACHMENTS
G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 350 LC-5 -9
ZAXIS 350 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

REFERRAL ATTACHMENTS Continued...

ETN85108 Auxilary Counterweight, 2000 lbs. Bottom Mount 6,440.00


Parts are primed only (contact GR Mfg for paint color).

ETN85109 Auxilary Counterweight, 4300 lbs, Bottom Mount, 22m Arm 10,864.00
Parts are primed only (contact GR Mfg for paint color).

ETN85142 Front Window Guard, Polycarbonate 2,550.00

AT401261 Guard, Slant Top Rub Rails 2,100.00


Parts are primed only (contact GR Mfg for paint color).

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 350 LC-5 -10
ZAXIS 350 LC-5 EXCAVATOR
Continued

THIS PAGE IS INTENTIONALLY LEFT BLANK

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 470 LC-5 -1
ZAXIS 470 LC-5 EXCAVATOR
Equipment for Base Machine

ENGINE: Nine Lower Rollers Fuel Gauge with Low Fuel


Isuzu 6UZ1 certified to IT4 / Three Upper Rollers Indicator
Stage IIIB emissions Spring Applied Hydraulic Work Mode Indicator
367 Horsepower Net Peak Power Released Propel Brake Auto Idle Indicator
(ISO 9249) UPPER STRUCTURE: Auto Shut Down Indicator
Turbocharger Right and Left Mirrors Alternator Charge Indicator
Charge Air Cooler Toolbox Air Filter Restriction
Auto-Idle System Vandal Locks for: Indicator
Cool-on-Demand Hydraulic-Driven Cab Door Fault Code Alert Indicator
Fan Service Doors Check Engine Indicator
Hydraulic Fan Reverser Fuel Cap Wiper Mode Indicator
Antifreeze Protection to -34F Tool Box Work Lights On Indicator
(-37C) Work Lights: Fuel Rate Display
Enclosed Fan Guard One Mounted on Frame Clock
Hinged A/C Condenser and Fuel Two Mounted on Boom Hour Meter
Cooler Two Mounted on Cab Mode Selection:
Dual Element Dry-type Air Filter Debris Screen in Side Panel One Work Mode
with Restriction Indicator Remote Mounted Engine Oil Three Power Modes
Full Flow Oil Filter Filter Boom Mode
Fuel Filters with Water FRONT ATTACHMENT: Numerous Attachment Modes
Separators Centralized Lubrication System Engine Oil Level Indicator
Underhood After Treatment Device Dirt Seals on Bucket Pins Engine Coolant Level Indicator
with Curved Exhaust Less Boom Auto-Climate Control/Air
Heavy Duty, Low Maintenance Less Arm Conditioner, Heater with
Batteries Less Bucket Pressurizer
Glow Plug Start Aid OPERATOR'S STATION: AM-FM Radio
50-Amp Alternator - 24 Volt ZXLink Ultimate Machine Machine Information Center
500 Hour Engine Oil Change Monitoring System w/ 3-year (MIC)
Interval Message Service (Available in Windshield Wiper/Washer with
70% (35) Off Level Capability United States and Canada only) Intermittent Speed
HYDRAULICS: Adjustable Control Positions 12V-60W, 5 Amp Cell Phone Power
Open Center, Load Sensing with (Levers to Seat, Seat to Outlet
Variable Displacement Pumps Pedals) 2 In. Retractable Seat Belt
Hydraulic Pilot Controls 4" Arm Rests Attached to Side Tinted Safety Glass
Axial Piston Swing Motor Consoles Hot/Cold Box Compartment
Multiple Wet Disk Swing Brake Pilot Control Shut-Off Lever Horn
Auxiliary Valve Section Short Stroke, Low Effort Pilot Two Cup Holders
Adjustable Flow for Attachments Levers Interior Light
Through Monitor Deluxe Adjustable, Heated Cloth Coat Hook
Boom and Arm Reduced Drift Seat with Air Suspension, Floor Mat
Valves Reclining Backrest, Headrest, Motion Alarm with Cancel Switch
Hydraulic Tank Site Gauge and Adjustable Lumbar Support Transparent Tinted Roof Hatch
4,000 Hour Hydraulic Oil Change Multifunction, Color LCD Monitor with Sunshade
Interval System with: Easy Access Air Conditioning
UNDERCARRIAGE: Diagnostic Capability Filter
Two Speed Propel with Systems Monitoring Capability
Auto-Shift Multiple Language Capability
Axial Piston Propel Motors Maintenance Tracking
Propel Motor Shields Engine Coolant Temperature
Planetary Final Drives Gauge
Sealed and Lubricated Track Engine Coolant Temperature
Chain Warning Indicator with Audible
Front and Center Track Guides Alarm
X-Frame Car Body Engine Oil Pressure Warning
Hydraulic Track Adjuster Indicator with Audible Alarm

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B. US/Canadian Port of Entry for Complete Machine.
F.O.B. Kernersville, North Carolina for 470 boom and arm, or Port of Entry depending on
configuration.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 470 LC-5 -2
ZAXIS 470 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

BASE MACHINE Continued...


4290FF ZAXIS 470 LC-5 EXCAVATOR 465,509.00

MACHINE CONNECTIVITY
Machine connectivity functions require cellular coverage. Usage of ZXLink System requires
customer's acceptance of the terms of the John Deere Telematics System Contract.

Option availability limited by specific geographical regions. Please refer to region specific price
pages for appropriate ordering codes.

1700 ZXLink Ultimate Cellular for the Americas, excluding Costa Rica In Base Price
Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway
(MTG), and ZXLink Ultimate activation.

Includes 3 year subscription. Annual subscription renewal required after 3 years for continued
functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to
www.StellarSupport.com to renew or update ZXLink subscriptions.

1741 No ZXLink Ultimate No Charge

MAIN FRAME
2620 Standard main frame and counterweight w/o removal device -4,415.00
Will not accept counterweight removal device.

2625 Modified Mainframe and Counterweight In Base Price


Will accept counterweight removal device.

2650 Modified Mainframe and Counterweight with Counterweight Removal Device 8,889.00
Includes factory installed counterweight removal device.

TRACK SHOES
3275 750 mm (30 In.) Triple-Bar Semi-Grouser Shoes No Charge
Recommended for rocky terrain, hard ground and stumps.

3350 900 mm (36 In.) Triple-Bar Semi-Grouser Shoes In Base Price


Recommended for general conditions and soft terrain.

BOOM
6801 Less Boom In Base Price
Excludes Arm Cylinder, Boom Cylinders and Plumbing on Boom.
Includes Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins.
Code 9010 Boom Cylinders recommended.
The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is
recommended.

6840 6.3M (20 ft 8 in) One Piece, Mass Excavating (ME) Boom with Arm Cylinder and Plumbing 70,601.00
Requires code 7275, Mass-Excavating (ME) Arm.
Check availability, may require long lead time.

6940 7.0 M (23 ft.) HD Boom with Arm Cylinder and Plumbing 71,945.00
Similar to the Heavy-Duty Boom on Previous Series

ARMS

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 470 LC-5 -3
ZAXIS 470 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ARMS Continued...
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price
Hydraulic Filter Indicator Recommended.

7160 2.9 M (9 Ft. 6 In.) Arm Assembly w/ Bucket Cylinder & Linkage 34,072.00

7180 3.4 M (11 Ft. 2 In.) Arm with Bucket Cylinder and Linkage 34,509.00
Recommended for hammer or high density material applications.

7250 3.9 M (12 Ft. 10 In.) Arm Assembly w/ Bucket Cylinder & Linkage 34,755.00

7275 2.9 M (9 Ft. 6 In.) Mass Excavating (ME) Arm with Bucket Cylinder and Linkage 39,469.00
Requires Code 6840 Mass Excavating Boom.
Check availability, may require long lead time.

7285 4.9 M (16 Ft. 1 In.) Arm with Bucket Cylinder and Linkage 34,985.00
Requires Long Lead Time, check with your dealer for availability.
Will not accept 450 buckets due to the pin diameters. Use 350-size buckets.

BUCKETS
8001 Less Buckets In Base Price
Includes bucket mounting pins.

8360 60 In. (1525 mm), 3.17 Yd3 (2.42 M3) Heavy-Duty, High-Capacity Bucket 16,466.00
Includes Six (6) Esco Super-V EV43SYL Teeth

8380 72 In. (1830MM) 3.97 Yd3 (3.04 M3) Heavy-Duty, High-Capacity Bucket 17,808.00
Includes Seven (7) Esco Super-V EV43SYL Teeth

OPTIONAL EQUIPMENT--ORDER AS DESIRED


9010 Boom Cylinders with Plumbing to Main Frame 19,026.00
Requires 6801, Less Boom, and Code 7001, Less Arm.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Side Cutters:

AT342513 Side-Cutter Kit, 6 inch 485.00

Guards:

AT419609 Cab FOPS Guard 2,533.00


FOPS Level II, ISO 10262 Certified

Hydraulic Couplers:

AT343233 Hydraulic Quick Coupler 11,874.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 470 LC-5 -4
ZAXIS 470 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Hydraulic Thumb Kits:
Please click on the following link to access the freight rate tables.

AT379664 Hydraulic Thumb Kit, Progressive 13,990.00


Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and
tooth spacing.

Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.

Hydraulics:

AT335922 Accumulator Kit 6,437.00


Requires the installation of High-Flow Auxiliary Hydraulic Lines prior to installing this kit.

AT338257 Anti-Drift Valve with Plumbing and Hardware, Arm Cylinder 3,496.00
Installation Instruction T228319

AT316251 Boom Anti-Drift Kit 3,887.00


Installation Instruction T217533

AT327652 Control Handle for Auxiliary Hydraulics, Left-Hand 505.00


Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size
excavators.
Requires control solenoid for either 1-way or 2-way auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390774 Control Handle for Auxiliary Hydraulics, Right-Hand 256.00


Also order solenoids for auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT330567 Control Solenoids for 2-Way Auxiliary Hydraulics 768.00


Monitor can be used to control hydraulic flow.
Can be used with either right-hand or left-hand control handle.
Installation Instructions T223910.

AT327632 Filter Restriction Indicator 758.00


This kit is recommended when the excavator will be equipped with front attachment such as crushers,
thumbs, hammers, log loaders, etc.
Installation Instruction T229238

AT418864 High-Flow Auxiliary Hydraulic Lines for 3.4 M Arm 12,111.00


Includes 1.25 in ID piping with selector valve for direct return to tank and arm mounted shut off
valves.
Includes In Line Return Filter for Direct Return to Tank.
Includes dual pump combined flow functionality. Also, includes adjustable relief circuit which is
operator activated through the monitor.

AT418865 High-Flow Auxiliary Hydraulic Lines for 3.9 M Arm 12,227.00


Includes 1.25 in ID piping with selector valve for direct return to tank and arm mounted shut off
valves.
Includes In Line Return Filter for Direct Return to Tank.
Includes dual pump combined flow functionality. Also, includes adjustable relief circuit which is
operator activated through the monitor.

AT390776 Single Pedal Propel Kit 2,039.00

Operator Environment:

AT173678 3 Inch Seat Belt See Parts

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 470 LC-5 -5
ZAXIS 470 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT390824 Guard, Lower Front Window ISO Level II 1,028.00

AT390823 Guard, Upper Front Window ISO Level II 772.00

ETN93549 MP3 Player Field Kit 156.00

AT390720 Mechanical Pattern Changer 1,314.00

Overall Vehicle:

AT390721 Vandal Cover Kit 2,164.00

REFERRAL ATTACHMENTS
G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

ETN90043 Front Window Guard, Polycarbonate 2,550.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 470 LC-5 -6
ZAXIS 470 LC-5 EXCAVATOR
Continued

THIS PAGE IS INTENTIONALLY LEFT BLANK

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 670 LC-5 -1
ZAXIS 670 LC-5 EXCAVATOR
Equipment for Base Machine

ENGINE: Spring Applied Indicator with Audible Alarm


Isuzu 6WG1 certified to IT4 / Hydraulic Released Propel Brake Fuel Gauge with Low Fuel
Stage IIIB emissions Indicator
463 Horsepower Net Peak Power UPPER STRUCTURE: Work Mode Indicator
(ISO 9249) Right and Left Mirrors Auto Idle Indicator
Turbocharger Toolbox Auto Shut Down Indicator
Charge Air Cooler Vandal Locks for: Alternator Charge Indicator
Auto-Idle System Cab Door Air Filter Restriction
Cool-on-Demand Service Doors Indicator
Hydraulic-Driven Fan Fuel Cap Fault Code Alert Indicator
Hydraulic Fan Reverser Tool Box Check Engine Indicator
Antifreeze Protection to -34 Work Lights: Wiper Mode Indicator
degrees F (-37 degrees C) One Mounted on Frame Work Lights On Indicator
Enclosed Fan Guard Two Mounted on Boom Fuel Rate Display
Hinged A/C Condenser and Two Mounted on Cab Clock
Fuel Cooler Debris Screen in Side Panel Hour Meter
Dual Element Dry-type Air Remote Mounted Engine Oil Mode Selection:
Filter Filter One Work Mode
with Restriction Indicator FRONT ATTACHMENT: Three Power Modes
Full Flow Oil Filter Centralized Lubrication System Boom Mode
Fuel Filters with Water Boom Cylinders with Plumbing Numerous Attachment Modes
Separators Dirt Seals on Bucket Pins Engine Oil Level Indicator
Underhood After Treatment Device Less Boom Engine Coolant Level Indicator
with Curved Exhaust Less Arm Auto-Climate Control/Air
Heavy Duty, Low Less Bucket Conditioner, Heater with
Maintenance Batteries Pressurizer
Glow Plug Start Aid OPERATOR'S STATION: AM-FM Radio
50-Amp Alternator - 24 Volt ZXLink Ultimate Machine Machine Information Center
500 Hour Engine Oil Monitoring System w/ 3-year (MIC)
Change Interval Message Service (Available in Windshield Wiper/Washer with
70% (35 degrees) Off Level United States and Canada only) Intermittent Speed
Capability Adjustable Control Positions 12V-60W, 5 Amp Cell Phone Power
HYDRAULICS: (Levers to Seat, Seat to Outlet
Open Center, Load Sensing with Pedals) 2 In. Retractable Seat Belt
Variable Displacement Pumps 4" Arm Rests Attached to Side Tinted Safety Glass
Hydraulic Pilot Controls Consoles Hot/Cold Box Compartment
Axial Piston Swing Motor Pilot Control Shut-Off Lever Horn
Multiple Wet Disk Swing Brake Short Stroke, Low Effort Pilot Two Cup Holders
Auxiliary Valve Section Levers Interior Light
Adjustable Flow for Deluxe Adjustable, Heated Cloth Coat Hook
Attachments Through Monitor Seat with Air Suspension, Floor Mat
Boom and Arm Reduced Reclining Backrest, Headrest, Motion Alarm with Cancel Switch
Drift Valves and Adjustable Lumbar Support Transparent Tinted Roof Hatch
Hydraulic Tank Site Gauge Multifunction, Color LCD Monitor with Sunshade
4,000 Hour Hydraulic Oil System with: Easy Access Air Conditioning
Change Interval Diagnostic Capability Filter
UNDERCARRIAGE: Systems Monitoring Capability
Two Speed Propel Multiple Language Capability
Axial Piston Propel Motors Maintenance Tracking
Propel Motor Shields Engine Coolant Temperature
Planetary Final Drives Gauge
Sealed Track Chain Engine Coolant Temperature
Front and Center Track Guides Warning Indicator with Audible
X-Frame Car Body Alarm
Hydraulic Track Adjuster Engine Oil Pressure Warning

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B. US/Canadian Port of Entry for Complete Machine.
F.O.B. Kernersville, North Carolina for 470 boom and arm, or Port of Entry depending on
configuration.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 670 LC-5 -2
ZAXIS 670 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

BASE MACHINE Continued...


4300FF ZAXIS 670 LC-5 EXCAVATOR 738,409.00

MACHINE CONNECTIVITY
Machine connectivity functions require cellular coverage. Usage of ZXLink System requires
customer's acceptance of the terms of the John Deere Telematics System Contract.

Option availability limited by specific geographical regions. Please refer to region specific price
pages for appropriate ordering codes.

1700 ZXLink Ultimate Cellular for the Americas, excluding Costa Rica In Base Price
Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway
(MTG), and ZXLink Ultimate activation.

Includes 3 year subscription. Annual subscription renewal required after 3 years for continued
functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to
www.StellarSupport.com to renew or update ZXLink subscriptions.

1741 No ZXLink Ultimate No Charge

MAIN FRAME
2625 Standard main frame and counterweight In Base Price
Will not accept counterweight removal device.

2650 Modified Mainframe and Counterweight with Counterweight Removal Device 22,902.00
Includes factory installed counterweight removal device.

TRACK SHOES
3200 650 mm (26 In.) Double-Bar Semi-Grouser Shoes -17,092.00
Recommended for rocky terrain, hard ground and stumps.

3300 750 mm (30 In.) Double-Bar Semi-Grouser Shoes -6,858.00


Recommended for general conditions.
Long Lead Time.

3350 900 mm (36 In.) Double-Bar Semi-Grouser Shoes In Base Price


Recommended for general conditions and soft terrain.

BOOM
6801 Less Boom, Arm Cylinder, and Plumbing on Boom In Base Price
Includes Boom Cylinders, Plumbing to Boom, and Pin Connecting Boom to Mainframe.
Requires "Less Arm".
The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is
recommended.

6840 6.8 M (22 Ft. 4 In.) One Piece, Mass Excavating (ME) Boom with Arm Cylinder and Plumbing 96,723.00
Requires code 7275, Mass-Excavating (ME) Arm.
Check availability, may require long lead time.

6845 7.8 M (25 Ft. 7 In.) One Piece Boom with Arm Cylinder and Plumbing 89,351.00

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price
Hydraulic Filter Indicator Recommended.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 670 LC-5 -3
ZAXIS 670 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ARMS Continued...
7180 3.6 M (11 Ft. 10 In.) Arm with Bucket Cylinder and Linkage 55,318.00

7265 4.2 M (13 Ft. 9 In.) Arm with Bucket Cylinder and Linkage 57,002.00

7270 5.3 M (17 Ft. 5 In.) Arm with Bucket Cylinder and Linkage 61,010.00

7275 2.9 M (9 Ft. 6 In.) Mass Excavating (ME) Arm with Bucket Cylinder and Linkage 73,980.00
Requires code 6850, Mass Excavating (ME) Boom

OPTIONAL EQUIPMENT--ORDER AS DESIRED

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Extreme-Duty, Plate Lip:


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339310 48 In (1219 mm), 3.39 yd3 (2.59 M3) Extreme-Duty, Plate-Lip Bucket 30,422.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 3.6 and 4.2 M Arms Only.

AT339312 48 In (1219 mm), 3.39 yd3 (2.59 M3) Extreme-Duty, Plate-Lip Bucket 31,736.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK700FD)
For use on the 2.9 M Mass Excavating Arm Only.

AT339314 54 In (1372 mm), 3.96 yd3 (3.03 M3) Extreme-Duty, Plate-Lip Bucket 34,510.00

Includes Four (5) John Deere TK-Series Fanggs Teeth (TK700FD). For use on the 3.6 and 4.2 M
Arms Only.
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 2.9 M Mass Excavating Arm Only.

AT339316 54 In (1372 mm), 3.96 yd3 (3.03 M3) Extreme-Duty, Plate-Lip Bucket 33,197.00

Includes Four (5) John Deere TK-Series Fanggs Teeth (TK700FD). For use on the 3.6 and 4.2 M
Arms Only.

AT339318 60 In (1524 mm), 4.54 yd3 (3.47 M3) Extreme-Duty, Plate-Lip Bucket 35,984.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK700FD)
For use on the 2.9 M Mass Excavating Arm Only.

Buckets, Heavy-Duty, High-Capacity:


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339293 36 In (914 mm), 2.29 yd3 (1.75 M3) Heavy-Duty, High-Capacity Bucket 19,337.00
Includes Three (3) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 3.6 and 4.2 M Arms Only.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 670 LC-5 -4
ZAXIS 670 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT339295 42 In (1067 mm), 2.84 yd3 (2.17 M3) Heavy-Duty, High-Capacity Bucket 20,972.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 3.6 and 4.2 M Arms Only.

AT339297 48 In (1219 mm), 3.39 yd3 (2.59 M3) Heavy-Duty, High-Capacity Bucket 22,025.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 3.6 and 4.2 M Arms Only.

AT339299 54 In (1372 mm), 3.96 yd3 (3.03 M3) Heavy-Duty, High-Capacity Bucket 23,487.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 3.6 and 4.2 M Arms Only.

AT339301 60 In (1524 mm), 4.54 yd3 (3.47 M3) Heavy-Duty, High-Capacity Bucket 24,502.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 3.6 and 4.2 M Arms Only.

AT339304 72 In (1829 mm), 5.70 yd3 (4.36 M3) Heavy-Duty, High-Capacity Bucket 28,726.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 3.6 and 4.2 M Arms Only.

AT339306 80 In (2032 mm), 6.49 yd3 (4.96 M3) Heavy-Duty, High-Capacity Bucket 31,413.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 3.6 and 4.2 M Arms Only.

AT339308 86 In (2184 mm), 5.77 yd3 (4.41 M3) Heavy-Duty, High-Capacity Bucket 29,767.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 2.9 M Mass Excavating Arm Only.

Buckets, Heavy-Duty:
Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339278 36 In (914 mm), 1.59 yd3 (1.22 M3) Heavy-Duty Bucket 13,516.00
Includes Three (3) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 5.3 M Arm Only.

AT339281 42 In (1067 mm), 1.98 yd3 (1.51 M3) Heavy-Duty Bucket 14,766.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 5.3 M Arm Only.

AT339283 48 In (1219 mm), 2.37 yd3 (1.81 M3) Heavy-Duty Bucket 15,373.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 5.3 M Arm Only.

AT339285 54 In (1372 mm), 2.76 yd3 (2.11 M3) Heavy-Duty Bucket 16,921.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 5.3 M Arm Only.

AT339291 60 In (1524 mm), 3.17 yd3 (2.42 M3) Heavy-Duty Bucket 17,628.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 5.3 M Arm Only.

Buckets, Side Cutters:

AT342513 Side-Cutter Kit, 6 inch 485.00

Buckets, Truck Loading:


Truck-loading buckets are not drilled to accept bolt-on sidecutters.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 670 LC-5 -5
ZAXIS 670 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339320 76 In (1931 mm), 5.02 yd3 (3.84 M3) Truck-Loading Bucket 21,543.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 3.6 and 4.2 M Arms Only.

AT339322 82 In (2083 mm), 5.50 yd3 (4.21 M3) Truck-Loading Bucket 23,103.00
Includes Seven (7) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 3.6 and 4.2 M Arms Only.

Guards:

AT419609 Cab FOPS Guard 2,533.00


FOPS Level II, ISO 10262 Certified

Hydraulics:

AT327652 Control Handle for Auxiliary Hydraulics, Left-Hand 505.00


Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size
excavators.
Requires control solenoid for either 1-way or 2-way auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390774 Control Handle for Auxiliary Hydraulics, Right-Hand 256.00


Also order solenoids for auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390776 Single Pedal Propel Kit 2,039.00

Operator Environment:

AT173678 3 Inch Seat Belt See Parts

AT390824 Guard, Lower Front Window ISO Level II 1,028.00

AT390823 Guard, Upper Front Window ISO Level II 772.00

ETN93549 MP3 Player Field Kit 156.00

AT390720 Mechanical Pattern Changer 1,314.00

REFERRAL ATTACHMENTS
G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 670 LC-5 -6
ZAXIS 670 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

REFERRAL ATTACHMENTS Continued...

ETN90043 Front Window Guard, Polycarbonate 2,550.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 870 LC-5 -1
ZAXIS 870 LC-5 EXCAVATOR
Equipment for Base Machine

ENGINE: Spring Applied Hydraulic Indicator


Isuzu 6WG1 certified to IT4 / Released Propel Brake Work Mode Indicator
Stage IIIB emissions UPPER STRUCTURE: Auto Idle Indicator
532 Horsepower Net Peak Power Right and Left Mirrors Auto Shut Down Indicator
(ISO 9249) Toolbox Alternator Charge Indicator
Turbocharger Vandal Locks for: Air Filter Restriction
Charge Air Cooler Cab Door Indicator
Electronic Engine Control Unit Service Doors Fault Code Alert Indicator
Auto-Idle System Fuel Cap Check Engine Indicator
Cool-on-Demand Hydraulic-Driven Tool Box Wiper Mode Indicator
Fan Work Lights: Work Lights On Indicator
Hydraulic Fan Reverser One Mounted on Frame Fuel Rate Display
Antifreeze Protection to -34 Two Mounted on Boom Clock
degrees F (-37 degrees C) Two Mounted on Cab Hour Meter
Enclosed Fan Guard Debris Screen in Side Panel Mode Selection:
Hinged A/C Condenser and Fuel Remote Mounted Engine Oil One Work Mode
Cooler Filter Three Power Modes
Dual Element Dry-type Air Filter FRONT ATTACHMENT: Boom Mode
with Restriction Indicator Centralized Lubrication System Numerous Attachment Modes
Full Flow Oil Filter Boom Cylinders with Plumbing Engine Oil Level Indicator
Fuel Filters with Water Dirt Seals on Bucket Pins Engine Coolant Level Indicator
Separators Less Boom Auto-Climate Control/Air
Underhood After Treatment Device Less Arm Conditioner, Heater with
with Curved Exhaust Less Bucket Pressurizer
Heavy Duty, Low Maintenance OPERATOR'S STATION: AM-FM Radio
Batteries ZXLink Ultimate Machine Machine Information Center
Glow Plug Start Aid Monitoring System w/ 3-year (MIC)
50-Amp Alternator - 24 Volt Message Service (Available in Windshield Wiper/Washer with
500 Hour Engine Oil Change United States and Canada only) Intermittent Speed
Interval Adjustable Control Positions 12V-60W, 5 Amp Cell Phone Power
70% (35 degrees) Off Level (Levers to Seat, Seat to Outlet
Capability Pedals) 2 In. Retractable Seat Belt
HYDRAULICS: 4" Arm Rests Attached to Side Tinted Safety Glass
Open Center, Load Sensing with Consoles Hot/Cold Box Compartment
Variable Displacement Pumps Pilot Control Shut-Off Lever Horn
Hydraulic Pilot Controls Short Stroke, Low Effort Pilot Two Cup Holders
Axial Piston Swing Motor Levers Interior Light
Multiple Wet Disk Swing Brake Deluxe Adjustable, Heated Cloth Coat Hook
Auxiliary Valve Section Seat with Air Suspension, Floor Mat
Adjustable Flow for Attachments Reclining Backrest, Headrest, Motion Alarm with Cancel Switch
Through Monitor and Adjustable Lumbar Support Transparent Tinted Roof Hatch
Boom and Arm Reduced Drift Multifunction, Color LCD Monitor with Sunshade
Valves System with: Easy Access Air Conditioning
Hydraulic Tank Site Gauge Diagnostic Capability Filter
4,000 Hour Hydraulic Oil Change Systems Monitoring Capability
Interval Multiple Language Capability
UNDERCARRIAGE: Maintenance Tracking
Two Speed Propel Engine Coolant Temperature
Axial Piston Propel Motors Gauge
Propel Motor Shields Engine Coolant Temperature
Planetary Final Drives Warning Indicator with Audible
Sealed Track Chain Alarm
Front and Center Track Guides Engine Oil Pressure Warning
X-Frame Car Body Indicator with Audible Alarm
Hydraulic Track Adjuster Fuel Gauge with Low Fuel

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
F.O.B. US/Canadian Port of Entry for Complete Machine.
F.O.B. Kernersville, North Carolina for 470 boom and arm, or Port of Entry depending on
configuration.
See DEALER-INSTALLED ATTACHMENT section for additional source notes.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 870 LC-5 -2
ZAXIS 870 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

BASE MACHINE Continued...


4310FF ZAXIS 870 LC-5 EXCAVATOR 944,683.00

MACHINE CONNECTIVITY
Machine connectivity functions require cellular coverage. Usage of ZXLink System requires
customer's acceptance of the terms of the John Deere Telematics System Contract.

Option availability limited by specific geographical regions. Please refer to region specific price
pages for appropriate ordering codes.

1700 ZXLink Ultimate Cellular for the Americas, excluding Costa Rica In Base Price
Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway
(MTG), and ZXLink Ultimate activation.

Includes 3 year subscription. Annual subscription renewal required after 3 years for continued
functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to
www.StellarSupport.com to renew or update ZXLink subscriptions.

1741 No ZXLink Ultimate No Charge

MAIN FRAME
2625 Standard main frame and counterweight In Base Price
Will not accept counterweight removal device.

2650 Modified Mainframe and Counterweight with Counterweight Removal Device 22,139.00
Includes factory installed counterweight removal device.

TRACK SHOES
3200 650 mm (26 In.) Double-Bar Semi-Grouser Shoes -10,939.00
Recommended for rocky terrain, hard ground and stumps.

3300 750 mm (30 In.) Double-Bar Semi-Grouser Shoes -5,555.00


Recommended for general conditions.
Long Lead Time.

3350 900 mm (36 In.) Double-Bar Semi-Grouser Shoes In Base Price


Recommended for general conditions and soft terrain.

3400 1020 mm (40 In.) Double-Bar Semi-Grouser Shoes 8,995.00


Recommended for general conditions and soft terrain.

BOOM
6801 Less Boom, Arm Cylinder, and Plumbing on Boom In Base Price
Includes Boom Cylinders, Plumbing to Boom, and Pin Connecting Boom to Mainframe.
Requires "Less Arm".
The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is
recommended.

6850 7.1 M (23 Ft. 4 In.) One Piece Mass Excavating (ME) Boom with Arm Cylinder and Plumbing 129,835.00
Requires code 7275, Mass-Excavating (ME) Arm.
Check availability, may require long lead time.

6855 8.4 M (27 Ft. 7 In.) Standard One Piece Boom with Arm Cylinder and Plumbing 108,850.00

6870 10.4 M (32 ft. 10 in.) One Piece Boom with Boom Cylinders, Arm Cylinders, and Plumbing 128,693.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 870 LC-5 -3
ZAXIS 870 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

BOOM Continued...
Requires code 7265 or 7270.
Includes remote grease bank.
Includes unique lift chart for factory installed booms.
Boom cylinders are unique to this boom.

ARMS
7001 Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses In Base Price
Hydraulic Filter Indicator Recommended.

7180 3.7 M (12 Ft. 2 In.) Arm with Bucket Cylinder and Linkage 72,260.00

7265 4.4 M. (14 Ft. 5 In.) Arm with Bucket Cylinder and Linkage 76,819.00

7270 5.4 M. (17 Ft. 9 In.) Arm with Bucket Cylinder and Linkage 83,813.00
The 5.4 M Arm requires 650-size buckets.

7275 2.95 M (9 Ft. 8 In.) Mass Excavating (ME) Arm with Bucket Cylinder and Linkage 80,777.00
Requires code 6850, Mass Excavating (ME) Boom

OPTIONAL EQUIPMENT--ORDER AS DESIRED

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets, Extreme-Duty, Plate Lip:


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339350 48 In (1218 mm), 3.65 yd3 (2.79 M3) Extreme-Duty, Plate-Lip Bucket 37,582.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK700FD)
For use on the 3.7 and 4.4 M Arms Only.

AT339352 48 In (1218 mm), 3.65 yd3 (2.79 M3) Extreme-Duty, Plate-Lip Bucket 37,061.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 2.95 M Mass Excavating Arm Only.

AT339354 54 In (1372 mm), 4.27 yd3 (3.26 M3) Extreme-Duty, Plate-Lip Bucket 40,518.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 3.7 and 4.4 M Arms Only.

AT339356 54 In (1372 mm), 4.27 yd3 (3.26 M3) Extreme-Duty, Plate-Lip Bucket 40,009.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 2.95 M Mass Excavating Arm Only.

AT339358 60 In (1524 mm), 4.89 yd3 (3.74 M3) Extreme-Duty, Plate-Lip Bucket 42,104.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 3.7 and 4.4 M Arms Only.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 870 LC-5 -4
ZAXIS 870 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT339360 60 In (1524 mm), 4.89 yd3 (3.74 M3) Extreme-Duty, Plate-Lip Bucket 41,584.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 2.95 M Mass Excavating Arm Only.

AT339363 72 In (1829 mm), 6.17 yd3 (4.72 M3) Extreme-Duty, Plate-Lip Bucket 45,263.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 2.95 M Mass Excavating Arm Only.

Buckets, Heavy-Duty, High-Capacity:


Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339334 36 In (914 mm), 2.48 yd3 (1.90 M3) Heavy-Duty, High-Capacity Bucket 25,926.00
Includes Three (3) John Deere TK-Sereis Fanggs Teeth (TK700FD).
For use on the 3.7 and 4.4 M Arms Only.

AT339336 42 In (1067 mm), 3.05 yd3 (2.33 M3) Heavy-Duty, High-Capacity Bucket 29,641.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 3.7 and 4.4 M Arms Only.

AT339338 48 In (1218 mm), 3.65 yd3 (2.79 M3) Heavy-Duty, High-Capacity Bucket 30,560.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 3.7 and 4.4 M Arms Only.

AT339340 54 In (1372 mm), 4.27 yd3 (3.26 M3) Heavy-Duty, High-Capacity Bucket 32,479.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK700FD.)
For use on the 3.7 and 4.4 M Arms Only.

AT339342 60 In (1524 mm), 4.89 yd3 (3.74 M3) Heavy-Duty, High-Capacity Bucket 33,977.00

AT339344 72 In (1829 mm), 6.17 yd3 (4.72 M3) Heavy-Duty, High-Capacity Bucket 36,926.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 3.7 and 4.4 M Arms Only.

AT339346 80 In (2032 mm), 7.02 yd3 (5.37 M3) Heavy-Duty, High-Capacity Bucket 37,718.00
Includes Seven (7) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 3.7 and 4.4 M Arms Only.

AT339348 90 In (2286 mm), 7.46 yd3 (5.70 M3) Heavy-Duty, High-Capacity Bucket 36,565.00
Includes Seven (7) John Deere TK-Series Fanggs Teeth (TK600FD).
For use on the 2.9 M Mass Excavating Arm Only.

Buckets, Heavy-Duty:
Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339324 36 In (914 mm), 1.87 yd3 (1.43 M3) Heavy-Duty Bucket 17,950.00
Includes Three (3) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 5.4 M Arm Only.

AT339326 42 In (1067 mm), 2.32 yd3 (1.77 M3) Heavy-Duty Bucket 19,461.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 5.4 M Arm Only.

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 870 LC-5 -5
ZAXIS 870 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT339328 48 In (1219 mm), 2.78 yd3 (2.13 M3) Heavy-Duty Bucket 20,427.00
Includes Four (4) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 5.4 M Arm Only.

AT339330 54 In (1372 mm), 3.24 yd3 (2.48 M3) Heavy-Duty Bucket 21,815.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 5.4 M Arm Only.

AT339332 60 In (1524 mm), 3.72 yd3 (2.84 M3) Heavy-Duty Bucket 23,115.00
Includes Five (5) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 5.4 M Arm Only.

Buckets, Side Cutters:

AT342513 Side-Cutter Kit, 6 inch 485.00

Buckets, Truck Loading:


Truck-loading buckets are not drilled to accept bolt-on sidecutters.
Buckets come standard with horizontal wear strips.
Vertical wear strips in lieu of horizontal are available at no additional charge.
The switch to vertical wear strips MUST be indicated in the comments section of your order.

AT339368 84 In (2134 mm), 5.66 yd3 (4.33 M3) Truck-Loading Bucket 29,097.00
Includes Six (6) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 3.7 and 4.4 M Arms Only.

AT339372 92 In (2337 mm), 6.28 yd3 (4.80 M3) Truck-Loading Bucket 31,054.00
Includes Eight (8) John Deere TK-Series Fanggs Teeth (TK700FD).
For use on the 3.7 and 4.4 M Arms Only.

Guards:

AT419609 Cab FOPS Guard 2,533.00


FOPS Level II, ISO 10262 Certified

Hydraulics:

AT327652 Control Handle for Auxiliary Hydraulics, Left-Hand 505.00


Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size
excavators.
Requires control solenoid for either 1-way or 2-way auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390774 Control Handle for Auxiliary Hydraulics, Right-Hand 256.00


Also order solenoids for auxiliary hydraulics.
Recommended for use with auxiliary hydraulic lines.

AT390776 Single Pedal Propel Kit 2,039.00

Operator Environment:

AT173678 3 Inch Seat Belt See Parts

AT390824 Guard, Lower Front Window ISO Level II 1,028.00

AT390823 Guard, Upper Front Window ISO Level II 772.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS H-2-ZAXIS 870 LC-5 -6
ZAXIS 870 LC-5 EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


ETN93549 MP3 Player Field Kit 156.00

AT390720 Mechanical Pattern Changer 1,314.00

REFERRAL ATTACHMENTS
G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

ETN90043 Front Window Guard, Polycarbonate 2,550.00

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 1
ZX17U-2 COMPACT EXCAVATOR
Equipment for Base Machine

ENGINE: End of Boom 2 in. Retractable Seat Belt


Yanmar 3THV70 3-52.1 cu. in. Horn
(0.85 l) UNDERCARRIAGE: Hour Meter
14.8 ISO9249 Net HP (11.0 kW) 9.1 in. (230 mm) Rubber Track Instrumentation Lights
Certified to EPA Tier 4 Final Backfill Blade Monitor System with:
Engine Coolant Propel Motor Shield Alternator Charge Warning
Single Dry-Type Air Filter Planetary Final Drive Light
Electric Fuel Shutoff Two Speed Travel Engine Coolant Temperature
Fan Guard 5 ft. 2 in. (1.57 m) Overall Gauge and
Full Flow Oil Filter Track Length Warning Light
Low Maintenance Battery 4 ft. (1.21 m) Ground and Alarm
Fuel Filter & Water Separator Contact Length Engine Oil Pressure Warning
Isolation Mounted Axial Piston Propel Motor Light
Under Hood Muffler Travel Mode Indicator
40 Amp Alternator - 12 Volt UPPERSTRUCTURE: Fuel Gauge and Warning Light
Glow Plugs Cold Start Aid 360 Degree Upper Structure Engine Preheat Indicator
Rotation Light Switch with "On"
HYDRAULICS: Independent Boom Swing Indicator
Open Center with Two Variable (70 degree left and Two Travel Modes with Foot
Displacement Pumps and 50 degree Selection Switch
One Fixed Gear Pump right Propel Motion Alarm with Cancel
Hydraulic Pilot Controls for rotation) Cupholder
Boom, Arm, Bucket, Swing, ROPS/OPG/FOPS Canopy 12 Volt Cell Phone Outlet
and Propel Work light, mounted on Boom Operator manual storage in back
Excavator to Backhoe Control Counterweight 507 lb. of seat
Pattern Change Valve (230 kg.)
Auxiliary Function Foot Toolbox
Control
Boom Swing Foot Control FRONT ATTACHMENTS:
Axial Piston Swing Motor Boom 6 ft. (1.82 m)
Wet Disk Swing Brake Arm 3 ft. 1 in. (0.93 m)
Propel Brake Mechanical Quick Coupler
Auxiliary Valve Section
Auxiliary Hydraulic Lines with OPERATOR'S STATION:
Release Under Pressure Adjustable Vinyl Seat
Hydraulic Quick Couplers to - fore and aft

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

Select One Code From Each Required Category

BASE MACHINE
6930FF ZX17U-2 COMPACT EXCAVATOR 29,166.00

TRACK
3125 9 in. (230 mm) Rubber Track In Base Price

3128 9 in. (230 mm) Steel Track with Triple Semi-Grouser Shoes 462.00

3130 Rubber City Pads 2,239.00


NOTE:
* Shipped from the nearest port
* Factory Hydraulic Clamp installation is not available; dealer-installed only
* Steel track shoes with vulcanized rubber pads bonded to top of shoes.
* Long lead-time item; contact Order Fulfillment for availability

ARM
7110 Standard Arm 3 ft. 1 in. (0.93 m) In Base Price

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 2
ZX17U-2 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ARM Continued...
7120 Long Arm 3 ft. 8 in. (1.13 m) and Extra Counterweight 176 lb. (80 kg) 1,247.00
NOTE:
* Long lead-time item; contact Order Fulfillment for availability.
* Extra counterweight extends 5 in. (115 mm) beyond width of tracks when upper structure is rotated
to the side

SEAT
4140 Standard Seat - Vinyl In Base Price

4145 Suspension Seat - Vinyl 321.00


NOTE: Long lead-time item; contact Order Fulfillment for availability

EXPORT CODES
Translated Customer Delivery Packets can be ordered using the John Deere Technical Information
Bookstore at http://www.johndeeretechinfo.com at no charge. The Translated Delivery Packets
include the Operator Manual, Decal Kit, Warranty Information Booklet, and Uptime Maintenance
Planner. Search for and order the Translated Delivery Packets by model and language that meets
your customer requirements. A listing of all Translated Delivery Packets available can be found by
selecting Translated Delivery Packets from the Manual Type dropdown list. Technical support is
available by calling 1-866-213-3373.

ATTACHMENTS FOR FIELD CONVERSION


F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may
require additional parts for a complete installation. Prior to ordering, check the installation
instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this
Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment
installation instruction bulletin for additional parts.
Exception to above note is FRONTIER Dealer Installed Kits.

Buckets:

AT316548G 12 In. (305 mm) Heavy Duty GREY Bucket; 443.00


0.8 Cu. Ft. (0.027 Cu. M) (3 Teeth Included)

AT316549G 16 In. (406 mm) Heavy Duty GREY Bucket; 478.00


1.2 Cu. Ft. (0.03 Cu. M) (3 Teeth Included)

AT316550G 18 In. (457 mm) Heavy Duty GREY Bucket; 520.00


1.4 Cu. Ft. (0.04 Cu. M) (4 Teeth Included)

AT316547G 9 In. (229 mm) Heavy Duty GREY Bucket; 0.6 399.00
Cu. Ft.
(0.020 Cu. M)

Clamps:

AT349585 Hydraulic Clamp, Long Arm - Factory Installation Fee 623.00


NOTE:
* Must also order Hydraulic Clamp
* Cannot be ordered with Rubber Crawler Pads, 3130

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 3
ZX17U-2 COMPACT EXCAVATOR
Continued

SUGGESTED
LIST PRICE
CODE DESCRIPTION USD ($)

ATTACHMENTS FOR FIELD CONVERSION Continued...


AT349584 Hydraulic Clamp, Short Arm - Factory Installation Fee 508.00
NOTE:
* Must also order Hydraulic Clamp
* Cannot be ordered with Rubber Crawler Pads, 3130

AT318254G Hydraulic GREY Clamp, Short and Long Arms 1,651.00

Engine:

AT358708 Engine Coolant Heater (110 Volt) See Parts


NOTE:
* Recommended for use in temperatures 32 degrees F / 0 degrees C, and below.
* For model 17, also order Adapter Kit (Part AM882530)

Kits and Accessories:

AT171619 3 in. Retractable Seat Belt See Parts

TY25876 Heavy Duty Battery See Parts


NOTE:
* Recommended for Cold Start climates
* Requires 2 Electrical Connectors (Part PMA4U)

REFERRAL ATTACHMENTS
G.R. Mfg.:
G.R. Manufacturing, Inc.
* Kits listed below must be ordered through John Deere.
* F.O.B. Trussville, Alabama
* All kits include installation instructions
* All warranty, repair parts, technical support and assistance, and sales support and assistance will
be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer
and G.R. Manufacturing, Inc.

G.R. Manufacturing, Inc.


4800 Commerce Drive
Trussville, Alabama 35173
Phone: (800)841-8001
Fax: (205)655-8005

AT337084 Front Protection Screen for Canopy (17 CE) 670.00


NOTE:
* Required when a Hydraulic Breaker is equipped on a ZX17U-2 Compact Excavator with a canopy

01 May 2013
US
(Subject To Change Without Notice) CONSTRUCTION PRODUCTS 4
ZX17U-2 COMPACT EXCAVATOR
Continued

THIS PAGE IS INTENTIONALLY LEFT BLANK

01 May 2013
US

You might also like