You are on page 1of 18

GMR BUILDING

1903 2987 1250

WH1
WV1
WV2 WV3
2258
W2 D2
4102

WH2 JOIST J1
JOIST J3
1842 DW1
D2

589 W3 D1 WH3

WV5
W1 JOIST J2 3587
3000 WV4

WH4

3600
Floor to Floor Height of General Floor= 3.5 m
Floor to Roof Height of Top Floor= 3 m
Truss Heel Height= 0.2 m
Truss Ridge height= 1.5 m
DEAD LOAD
ROOF DEAD LOAD
Truss & Purlin= 15 Kg/sqm= 0.15 KN/sqm
9mm HD Board= 14.85 Kg/sqm= 0.15 KN/sqm
50MM XPS= 2.4 Kg/sqm= 0.02 KN/sqm
12 MM FCB Board= 17.4 Kg/sqm= 0.17 KN/sqm
Roof Single say= 15 Kg/sqm= 0.15 KN/sqm
50mm Insulation Ceiling 2.4 Kg/sqm= 0.02 KN/sqm
False Ceiling say= 15 Kg/sqm= 0.15 KN/sqm
Service and Colateral= 30 Kg/sqm= 0.30 KN/sqm
TOTAL= 1.12 KN/sqm

FLOOR DEAD LOAD


100mm Con(Eq Thickness=78mm)= 1.95 KN/sqm
50mm Finish= 1.00 KN/sqm
0.8 mm Deck Sheet= 10 Kg/sqm= 0.10 KN/sqm
Joist say 15 Kg/sqm= 0.15 KN/sqm
50mm Insulation Ceiling 2.4 Kg/sqm= 0.02 KN/sqm
False Ceiling say= 15 Kg/sqm= 0.15 KN/sqm
Service and Colateral= 30 Kg/sqm= 0.30 KN/sqm
Site Pouring Error Margin 25 mm Con= 0.00 KN/sqm
TOTAL= 3.67 KN/sqm
WALL SEFL WEIGHT
12mm Plank= 18 Kg/sqm 0.18 KN/sqm
9mm HD Board= 13.5 Kg/sqm 0.14 KN/sqm
STUD SAY= 9 Kg/sqm 0.09 KN/sqm
100mm insulation within Stud 4.8 Kg/sqm 0.05 KN/sqm
6mm HD Board= 9 Kg/sqm 0.09 KN/sqm
12.5mm Gyp Board 10 Kg/sqm 0.10 KN/sqm
TOTAL= 0.60 KN/sqm
LIVE LOAD
ROOF LIVE LOAD
Roof Inclination= 20 Degree
Load -Inaccessible Roof upto 10 degree= 0.75 KN/sqm
Load -Inaccessible Roof - 20 degree= 0.55 KN/sqm
FLOOR LIVE LOAD
For Residentail Use= 2.00 KN/sqm

AISI-IBC 2012 LOAD COMBINATIONS


Combina
tion Factor Load Factor Load Factor Load Factor Load Factor Load
STRENTH

Comb 1 1.2 DL 1.6 LLFLOor 0.5 LLroof


Comb 2 1.2 DL 1.0 LLFLOor 1.6 LLroof
Comb 3 0.9 DL 1.0 WLuplift 1.0 WLLateral
Comb 4 1.2 DL 1.0 LLFLOor 0.5 LLroof 1.0 WLthrust 1.0 WLLateral
Comb 5 0.9 DL 1.0 EL
Comb 6 1.2 DL 1.0 LLFLOor 1.0 LLroof 1.0 EL
SERVICEABILITY
Comb 7 1.0 LLFLOor 1.0 LLroof
Comb 8 1.0 DL 1.0 LLFLOor 1.0 LLroof
Comb 9 0.9 DL 1.0 WLuplift 0.7 WLLateral
Comb 10 1.0 DL 1.0 LLFLOor 1.0 LLroof 1.0 WLthrust 0.7 WLLateral
Comb 11 0.9 DL 1.0 EL
Comb 12 1.0 DL 1.0 LLFLOor 1.0 LLroof 1.0 EL

JOIST SPACING MAY GOVERN STUD SPACING IN LOAD BEARING WALL


JOIST DESIGN
Joist J1-DETAILED CALCULATIONS
Screw Connection Strenth for 12G(5.5mm Scew)= 2.65 KN Refer NASH DOCUMENT PAGE No 134
Assume Joist Spacing= 407 mm Say for 1 mm Sheet to 0.75 mm Sheet
Assumed Joist Depth= 400 mm
Joist Section Lip C 89-39-11-0.95
Con span= 2987 mm
Cantilever Span= 1250 mm
Gross Major Inertia of Section= 230633 mm4= 23.0633 cm4
Gross Minor Inertia of Section= 47197.24 mm4= 4.719724 cm4
Area of The Section= 125.255 mm2= 1.25255 cm2
Major Inertia of Section for Deflection Check= 213053.7 mm4= 21.30537 cm4
Minor Inertia of Section for Deflection Check= 30785.47 mm4= 3.078547 cm4
Distance of Cg from Web outside Face= 14.2 mm
Diagonal Node Spacing= 600 mm
Diagonal Lenth= 500 mm
Distance of Restrain in Chords= 1200 mm
Angle To Diagonal= Sin= 0.8 1.495318 KN/m
Cos= 0.6

Ra 600 Rb
Dead Load on Joist as UDL= 1.495318 KN/m

REACTIONS FOR DEAD LOAD


Ra+Rb= 6.336 KN
Taking Moment About Rb, Ra= 1.842 KN
Taking Moment About Ra, Rb= 4.494 KN

1.842 1.869

X -2.625

SHEAR FORCE DIAGRAM OF THE JOIST


Distance X where Shear Force is Zero= 1.232 m
Maximum Positive Bending Moment, Mpos= 1.135 KNm
Maximum Negative Bending Moment, MNeg= 1.168 KNm
FORCES DUE TO DEAD LOAD
Max Compression In Top Chord= 1.986 KN
Max Compression In Bottom Chord= 2.043 KN
Maximum Compression in Diagonals= 5.618 KN
Maximum Compression in Struct= 6.336 KN
FORCES DUE TO LIVE LOAD
Live Load on Joist as UDL= 0.814 KN/m
Max Compression In Top Chord= 1.081 KN
Max Compression In Bottom Chord= 1.112 KN
Maximum Compression in Diagonals= 3.058 KN
Maximum Compression in Struct= 3.449 KN

Forces Due to Load Combination


STRENGHT CHECK
Applicable Combination= LOAD COMB 1.0
Taking Capacity of Member for Lex= 600 mm and Ley= 600 mm
Capacity= 38.985 KN
Member Description Axial Load Capacity Utilizatio
n ratio
Max Compression In Top Chord= 4.11 KN 38.99 KN 0.11
Max Compression In Bottom Chord= 4.23 KN 38.99 KN 0.11
Maximum Compression in Diagonals= 11.63 KN 38.99 KN 0.30
Maximum Compression in Struct= 13.12 KN 38.99 KN 0.34
No of Screw Required= 5.00 ie 3 Each Side
Note :Generally More Than 4 Screw on Each Side Not Possible
Nominal Capacity of Screw Should 1.25 times Connection Capacity(Page 68 NASH)
SERCIABILITY CHECK
Applicable Combination= LOAD COMB 7.0 & LOAD COMB 8.0
Location of Point Of ContraFlexure from End A

2
Ra*X-wX /2=0
X= 2.46 m= 246.4 cm
Iyy= 3.08 cm4
A= 1.25 cm4
h= 18.58 cm
I of The Joist=3*IyySect+2*ASect*h2= 874.0372453 Cm4
E of Steel= 2074000 Kg/cm2
Allowable Deflection Due to Live Load = L/360 L/= 360
Allowable Deflection Due to Live Load = L/240 L/= 240
4
Deflection of Joist at Midspan= 5WL /(384EI) Between Points of ContraFlexure
Deflection of Cantilever= WL4/(8EI)
WLL= 1.495318 KN/m= 1.495318 Kg/Cm WDL+LL= 2.309318 KN/m= 2.309318 Kg/Cm

Load Span Type Deflection in Allowable Load Span Type Deflection Allowable
mm Deflection in mm Deflection

LOAD COMB 7.0 Cont 0.40 8.30 LOAD COMB 7.0 Cant 0.25 3.47
LOAD COMB 8.0 Cont 0.61 12.45 LOAD COMB 8.0 Cant 0.39 5.21

JOIST STERNTH DESIGN(ONLY SIMPLE SPAN)


Joist Name Load for Span in mm Chord Capacity Sturt Foce Capacity Sturt Diagonal Capacity
Load MaxDistance Force KN Chord KN KN KN Focce KN Diagonal
Spacing of Comb 1 BetweenPan KN
Joist in mm KN/m el Points

J2 610 4.64 600 3600 13.15 38.99 8.35 38.99 10.44 38.99
J3 610 4.64 600 1903 3.68 38.99 4.42 38.99 5.52 38.99
No of Screw Required= 2 on Each Side

JOIST SERVICEABILITY DESIGN(ONLY SIMPLE SPAN)


Wall No Joist Name Spacing Span in Cm Total Load Live Load inTotal
KN/m Def Allowable Live Load Def Allowable
STATUS
of Joist in in KN/m 5WL4/(384EI) in total 5WL4/(384EI) in Live
for Total
mm mm Deflectio mm LoadDefle
Load &
n in mm ction in
Live Load
mm

J2 407 360 2.31 0.81 2.786 15.00 0.982052027 10 OK OK


J3 407 190.3 2.31 0.81 0.218 7.93 0.076679566 5.286111 OK OK

WALL DESIGN(St-1-WV3-DETAILED)
Strength Check
Assume Stud Spacing= 407 mm= 0.407 m
Wall Height og General Floor= 3100 mm= 3.1 m
Wall Height of Top Floor= 3000 mm= 3m
Roof Dead Load= 1.12
Floor Dead Load= 3.67
Wall Self Weight= 0.60
Roof Live Load= 0.55
Floor Live Load= 2.00
Wall WV3-DETAILED CALCULATIONS
Tributary of Top Floor Wall= 2.74 m
Tributary of Second Floor Wall= 2.74 m
Tributray Area of Fisrt Floor Wall= 2.74 m
Max Width of Opening= 2.5 m
UDL on Wall Due to Dead Load
DL due To Roof= 3.07 KN/m
DL due Sec Floor Wall= 1.80 KN/m
DL due To Second Floor 10.08 KN/m
DL due First Floor Wall= 1.86 KN/m
DL due To First Floor 10.08 KN/m
DL due to Gr Floor Wall= 1.86 KN/m
Total= 28.75 KN/m Axial Load on Stud= 11.70 KN
UDL on Wall Due to Live Load
Floor
LL due To Second Floor 5.49 KN/m
LL due To First Floor 5.49 KN/m
Total= 10.97 KN/m Axial Load on Stud= 4.47 KN
Roof
LL due To Roof= 1.51 KN/m
Total= 1.51 KN/m Axial Load on Stud= 0.61 KN
UDL due To Wind Uplift
Wind Pressure 0.99 KN/Sq m Refer to Wind Load Calculations
WLuplift= 2.71 KN/m Axial Load on Stud= 1.10 KN

UDL due To Wind Thrust


Wind Pressure= 0.11 KN/Sq m Refer to Wind Load Calculations
WLthrust= 0.30 KN/m Axial Load on Stud= 0.12 KN

UDL due to Lateral Wind Pressure


Wind Pressure= 1.32 KN/Sq m
Critical Tirbutary Width of Jamb Stud= 1.45 m
Udl of Individual Stud= 0.54 KN/m
2
Bending Moment on Ind. Stud=wL /8= 0.64 KNm

Axial Capacity of Stud= 25.43 KN


Bending Capacity of Stud= 1.92 KNm
No of Stud for Wall 2
No of Stud for Jamb 3 Note: Not Possible To Provide More Than 4 Stud
If Jamp Post SHS 91.5x91.5x3.6 -Fy 310 Mpa required Even 4 Stud Requires Specail Detailing
Axial Capacity of SHS= 200 KN
Bending Capacity of SHS= 11.68 KNm
Individual Stud Jamb Stud Jamb Post Required
Load Combination Interation Interation
Axial KN BM KNm Axial KN BM KNm Interaction Ratio
Ratio Ration
Load Comb 1 21.50 0.42 76.77 0.00 1.01 0.38
Load Comb 2 19.49 0.38 69.61 0.00 0.91 0.35
Load Comb 3 9.43 0.64 0.35 33.67 2.30 0.84 0.37
Load Comb 4 18.94 0.64 0.54 67.64 2.30 1.29 0.54
A POST AS PER DESIGN ABOVE BE PROVIDED AT JAMB STUD

Serviceability Check
Deflection of Wall Stud to Lateral Pressure Between Floor Level
Maximum Lateral Wind Load External= 1.32 KN/Sqm
Maximum Lateral Wind Load Internal= 0.55 KN/Sqm
Load Comb 9 & 10, Applicable Wind Pressure= 0.7 WLLateral= 0.92 KN/Sqm
Stud Spacing= 0.407 m Lateral UDL on Stud= 0.38 KN/m= 0.38 Kg/Cm
No of Stud in Wall= 2 Nos
E= 2074000 Kg/Cm2
Istud deflection= 21.30537 Cm4
L= Clear Height of Stud= 310 cm
4
=5WL /384EI= 0.510577 Cm= 5.105768 mm
Allowable Deflection=L/240= 1.291667 cm= 12.91667 mm
Deflection is within Permissible Limit
STOREY WISE WALL DESIGN
Tributary Width of Walls
Top Storey First Storey Ground Storey
wall Name Tr Width Typical Wall wall Name Tr Width Typical Wall wall Tr Width in m Typical
in m from Frame in m from Frame Name Wall
Cad Cad from
Frame
Cad
St-3-WV1 0.952 St-2-WV1 0.952 St-1-WV1 0.952
St-3-WV2 2.445 St-2-WV2 2.445 St-1-WV2 2.445
St-3-WV3 2.744 St-2-WV3 2.744 St-1-WV3 2.744
St-3-WV4 1.800 St-2-WV4 1.800 St-1-WV4 1.800
St-3-WV5 1.800 St-2-WV5 1.800 St-1-WV5 1.800
St-3-WH1 0.204 St-2-WH1 0.204 St-1-WH1 0.204
St-3-WH2 0.407 St-2-WH2 0.407 St-1-WH2 0.407
St-3-WH3 0.407 St-2-WH3 0.407 St-1-WH3 0.407
St-3-WH4 0.204 St-2-WH4 0.204 St-1-WH4 0.204

Axial Capacity of Storey -3 Stud= 26.49 KN


Bending Capacity of Story- 3 Stud= 1.92 KNm

Axial Capacity of Storey 2 -Stud= 25.43 KN


Bending Capacity of Story 2 -Stud= 1.92 KNm

Axial Capacity of Storey- 1 Stud= 25.43 KN


Bending Capacity of Story -1 Stud= 1.92 KNm

DESIGN OF FEW CRITCALS WALLS Legend St-3-WV1 means wall named WV1 of Storey Number 3
Top Storey
Wall Stud Spacing No of Type of Critcal Interactio Deflection Allowable Jamb Stud No of Interactio
Name in Meter Stud Exopure to Load Comb n Ratio Deflection Tributary Stud in n ratio
Wind for Length Jamb
Strength
St-3-WV1 0.407 1 External Comb 4 0.37 8.96 12.5 0.80 1 0.74
St-3-WV2 0.407 1 Internal Comb 4 0.23 3.73 12.5 0.65 1 0.37
St-3-WV3 0.407 1 External Comb 4 0.42 8.96 12.5 1.45 2 0.75
St-3-WV4 0.407 1 External Comb 4 0.40 8.96 12.5 1.45 1 1.41
St-3-WV5 0.407 1 External Comb 4 0.40 8.96 12.5 0.00 1 0.00
St-3-WH1 0.407 1 External Comb 4 0.35 8.96 12.5 0.00 1 0.00
St-3-WH2 0.407 1 Internal Comb 4 0.17 3.73 12.5 0.00 1 0.00
St-3-WH3 0.407 1 Internal Comb 4 0.17 3.73 12.5 0.70 1 0.30
St-3-WH4 0.407 1 External Comb 4 0.35 8.96 12.5 0.00 1 0.09

Storey 2
Wall Stud Spacing No of Type of Critcal Interactio Deflection Allowable Jamb Stud No of Interactio
Name in Meter Stud Exopure to Load Comb n Ratio Deflection Tributary Stud in n ratio
Wind for Length Jamb
Strength
St-2-WV1 0.407 1 External Comb 4 0.53 8.96 12.5 0.80 2 0.52
St-2-WV2 0.407 1 Internal Comb 4 0.53 3.73 12.5 0.65 2 0.42
St-2-WV3 0.407 1 External Comb 4 0.76 8.96 12.5 1.45 4 0.68
St-2-WV4 0.407 1 External Comb 4 0.64 8.96 12.5 1.45 4 0.57
St-2-WV5 0.407 1 External Comb 4 0.64 8.96 12.5 0.00 2 0.00
St-2-WH1 0.407 1 External Comb 4 0.43 8.96 12.5 0.00 2 0.00
St-2-WH2 0.407 1 Internal Comb 4 0.26 3.73 12.5 0.00 2 0.00
St-2-WH3 0.407 1 Internal Comb 4 0.26 3.73 12.5 0.70 2 0.23
St-2-WH4 0.407 1 External Comb 4 0.43 8.96 12.5 0.00 2 0.12

Storey 1
Wall Stud Spacing No of Type of Critcal Interactio Deflection Allowable Jamb Stud No of Interactio
Name in Meter Stud Exopure to Load Comb n Ratio Deflection Tributary Stud in n ratio
Wind for Length Jamb
Strength
St-1-WV1 0.407 1 External Comb 4 0.66 8.96 12.5 0.80 2 0.65
St-1-WV2 0.407 2 Internal Comb 4 0.41 1.87 12.5 0.65 2 0.65
St-1-WV3 0.407 2 External Comb 4 0.54 4.48 12.5 1.45 3 1.29
St-1-WV4 0.407 2 External Comb 4 0.43 4.48 12.5 1.45 3 1.02
St-1-WV5 0.407 2 External Comb 4 0.43 4.48 12.5 0.00 2 0.00
St-1-WH1 0.407 1 External Comb 4 0.49 8.96 12.5 0.00 2 0.00
St-1-WH2 0.407 1 Internal Comb 4 0.34 3.73 12.5 0.00 2 0.00
St-1-WH3 0.407 1 Internal Comb 4 0.34 3.73 12.5 0.70 2 0.29
St-1-WH4 0.407 1 External Comb 4 0.49 8.96 12.5 0.00 2 0.19

Provide Jamb posts SHS 91.5x91.5x3.6mm where Jamp Stud Interaction Ratio Exeed 0.9 Marked in Red
LINTEL DESIGN(OPENING IN WALL St-1-WV3 )
Span of Opening= 2.5 m
Depth of Lintel Truss Beam= 0.9 m
Distance Bewteen Panel Point= 0.6
Digonal Lenght= 0.95 m
Angle To Diagonal= Sin= 0.95
Cos= 0.32

SCREWS AT LOWER HALF TO ALLOW ROTATION

From Design of Wall St-1-WV3


Dead Load= 28.75 KN/m
Floor Live Load= 10.97 KN/m
Roof Live Load= 1.51 KN/m
Wind Uplift= 2.71 KN/m
Wind Thrust= 0.30 KN/m
Load Comb Resultant Force in Capacity of Force in Capacity of Force in Comp.Capacity
load Bearing Strut Bearing Slung Slung Chord of Chord
(KN/m) Strut
Comb 1 52.82 66.02 37.54 69.59 34.41 47.34 38.99
Comb 2 47.89 59.87 37.54 63.10 34.41 42.93 38.99
Comb 3 23.17 28.96 37.54 30.53 34.41 20.77 38.99
Comb 4 46.53 58.17 37.54 61.31 34.41 41.71 38.99

Clearly The Lintel Truss Beam Requires Addittional Section to Share Load The Load
Providing a U Track A Shown Below on as a Header Beam
A

View A-A

SCREWS AT LOWER HALF TO ALLOW ROTATION

Assume % Load Carried by The Header Beam= 70 %


Max Udl Carried by U Track= 36.97180074
Maximum Bending Moment to be Resisted= 28.88 KNm
MaximumShear to be Resisted= 46.21 KN

Properties of U Track required


Web= 89 mm
Flange= 250 mm
Thickness= 4 mm
Bending Capacity= 28.75370797 KNm
Shear Capacity= 414 KN
Iyy of U Track 11622350.34 mm4= 1162.24 cm4
Deflection o f U Track 0.780129505 cm= 7.80 mm
Perm Deflection= 10.42 mm

Therefore New forced to be Resisted by Lintel Truss Beam


Load Comb Resultant Force in Capacity of Force in Capacity of Force in Comp.Capacity
load Bearing Strut Bearing Slung Slung Chord of Chord
(KN/m) Strut
Comb 1 15.85 19.81 35.25 20.88 34.50 14.20 39.00
Comb 2 14.37 17.96 35.25 18.93 34.50 12.88 39.00
Comb 3 6.95 8.69 35.25 9.16 34.50 6.23 39.00
Comb 4 13.96 17.45 35.25 18.39 34.50 12.51 39.00

Strenth of Srew Connection= 2.65 KN Refer NASH DOCUMENT PAGE No 134


No of Screw requred for Slung to Chord Connection= 4 on Each Side
No of Screw requred for Bearing Strut to Jamb Stud= 4 on Each Side
Comparing Capacity of Member Having Lmajor= 900 mm and Lminor= 900 mm
Capacity of C section as above= 34.41 KN
Screw Capacity= 2.65 KN
DESIGN OF FEW CRITICAL LINTEL TRUSS BEAM
Wall Lenght of Depth of Distance Critical Percent Forces in Force in Force in No of No of
Name Opening in m Truss Between Load Load Bearing Slung in Chords in KN Scew Req Scew Req
Beam Panel Points Comb Carried Strut in KN KN and and Status for for
by Lintel and Status Status Bearnig Diagonal
Truss Strut on on Each
Each Side Side

St-3-WV1 1.2 0.5 0.4 Comb 2 100 3 OK 3 OK 2 OK 1 1


St-3-WV2 0.9 0.5 0.4 Comb 2 100 3 OK 4 OK 2 OK 1 1
St-3-WV3 2.5 0.9 0.6 Comb 2 100 10 OK 11 OK 7 OK 2 3
St-3-WV4 2.5 0.9 0.6 Comb 2 100 8 OK 8 OK 6 OK 2 2
St-3-WV5 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0
St-3-WH1 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0
St-3-WH2 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0
St-3-WH3 1 0.5 0.5 Comb 2 100 2 OK 2 OK 1 OK 1 1
St-3-WH4 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0

St-2-WV1 1.2 0.5 0.4 Comb 1 100 8 OK 9 OK 5 OK 2 2


St-2-WV2 0.9 0.5 0.4 Comb 1 100 12 OK 13 OK 6 OK 3 3
St-2-WV3 2.5 0.9 0.6 Comb 1 30 11 OK 12 OK 8 OK 3 3
St-2-WV4 2.5 0.9 0.6 Comb 1 30 8 OK 8 OK 6 OK 2 2
St-2-WV5 0 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0
St-2-WH1 0 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0
St-2-WH2 0 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0
St-2-WH3 1 0.5 0.5 Comb 1 100 4 OK 5 OK 2 OK 1 1
St-2-WH4 0 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0

St-1-WV1 1.2 0.5 0.4 Comb 1 100 14 OK 15 OK 14 OK 3 3


St-1-WV2 0.9 0.5 0.4 Comb 1 100 22 OK 23 OK 22 OK 5 5
St-1-WV3 2.5 0.9 0.6 Comb 1 30 20 OK 21 OK 20 OK 4 4
St-1-WV4 2.5 0.9 0.6 Comb 1 30 14 OK 15 OK 14 OK 3 3
St-1-WV5 0 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0
St-1-WH1 0 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0
St-1-WH2 0 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0
St-1-WH3 1 0.5 0.5 Comb 1 100 7 OK 8 OK 7 OK 2 2
St-1-WH4 0 0 0 Comb 1 100 0 OK 0 OK 0 OK 0 0

Provide Header Beam As Designed above for Lintel of the Wall Opening in
Wall U Header Beam Properties Header Beam Design
Wall
Name Depth of U Flange Thickness in Percent Span of Load Comb Load on Effective I of Shear Bend
with Section in With in mm Load Beam in Header Header and and
Header mm mm Shared Meter KN/m Beam Cm4 Shear Bend
beam capacity Cap
over KN KNm
Opening
St-2-WV1 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-2-WV2 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-2-WV3 89 250 4 70 2.5 Comb 1 20.80 1161.47 26 & 416 16 & 29
St-2-WV4 89 250 4 70 2.5 Comb 1 14.70 1161.15 18 & 418 11 & 29
St-2-WV5 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-2-WH1 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-2-WH2 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-2-WH3 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-2-WH4 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req

St-1-WV1 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req


St-1-WV2 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-1-WV3 89 250 4 70 2.5 Comb 1 36.97 1148.59 46 & 428 29 & 29
St-1-WV4 89 250 4 70 2.5 Comb 1 25.85 1146.52 32 & 430 20 & 29
St-1-WV5 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-1-WH1 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-1-WH2 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-1-WH3 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req
St-1-WH4 0 0 0 0 0 Comb 1 0.00 0.00 Not Req Not Req

SERVICEABILITY CHECK LINTEL BEAM


Iyy of Cold Formed C Section for Deflection= 3.0785472 cm4
Area of C section for Deflection= 1.25255 cm2
Distance of Cg from Web Face for Deflection= 1.42 Cm
E of Steel= 2074000 Kg/Cm2
Wall Serviceabilty Check of Linet Truss and Lintel Header Beam
Name Distance of Max Total Live Load Percent I of Lintel I of Header Span of Total Load Live Load
Between Cg of Load Carried in Load Truss Beam Opening Total Load & Actual & Actual
Chords Truss Carried KN/m Shared by provided in cm Live Load Pemssible and
in Cm KN/m Lintel Truss Deflection of Deflection Perssible
Header Beam in mm Deflection
in mm & Status

St-3-WV1 37.16 3.49 0.52 100 874.0372 0 120 0.1 & 5 0 & 3.3
St-3-WV2 37.16 6.15 1.34 100 874.0372 0 90 0 & 3.8 0 & 2.5
St-3-WV3 57.16 6.68 1.51 100 2055.442 0 250 0.8 & 10.4 0.2 & 6.9
St-3-WV4 57.16 5.00 0.99 100 2055.442 0 250 0.6 & 10.4 0.1 & 6.9
St-3-WV5 0 5.00 0.99 100 0 0 0 0& 0 0& 0
St-3-WH1 0 2.16 0.11 100 0 0 0 0& 0 0& 0
St-3-WH2 0 2.52 0.22 100 0 0 0 0& 0 0& 0
St-3-WH3 47.16 2.52 0.22 100 1402.112 0 100 0 & 4.2 0 & 2.8
St-3-WH4 0 2.16 0.11 100 0 0 0 0& 0 0& 0

St-2-WV1 37.16 10.75 2.43 100 874.0372 0.00 120 0.2 & 5 0 & 3.3
St-2-WV2 37.16 21.89 6.23 100 874.0372 0.00 90 0.1 & 3.8 0 & 2.5
St-2-WV3 57.16 24.11 7.00 30 2055.442 1161.47 250 4 & 2 OK OK 0.9 & 10.4 0.3 & 6.9
St-2-WV4 57.16 17.08 4.59 30 2055.442 1161.15 250 3 & 1 OK OK 0.6 & 10.4 0.2 & 6.9
St-2-WV5 0 17.08 4.59 100 0 0.00 0 0& 0 0& 0
St-2-WH1 0 5.18 0.52 100 0 0.00 0 0& 0 0& 0
St-2-WH2 0 6.69 1.04 100 0 0.00 0 0& 0 0& 0
St-2-WH3 47.16 6.69 1.04 100 1402.112 0.00 100 0 & 4.2 0 & 2.8
St-2-WH4 0 5.18 0.52 100 0 0.00 0 0& 0 0& 0

St-1-WV1 37.16 18.01 4.33 100 874.0372 0.00 120 0.3 & 5 0.1 & 3.3
St-1-WV2 37.16 37.62 11.12 100 874.0372 0.00 90 0.2 & 3.8 0.1 & 2.5
St-1-WV3 57.16 41.54 12.48 30 2055.442 1148.59 250 7 & 2 OK OK 1.5 & 10.4 0.4 & 6.9
St-1-WV4 57.16 29.15 8.19 30 2055.442 1146.52 250 5 & 2 OK OK 1 & 10.4 0.3 & 6.9
St-1-WV5 0 29.15 8.19 100 0 0.00 0 0& 0 0& 0
St-1-WH1 0 8.19 0.93 100 0 0.00 0 0& 0 0& 0
St-1-WH2 0 10.86 1.85 100 0 0.00 0 0& 0 0& 0
St-1-WH3 47.16 10.86 1.85 100 1402.112 0.00 100 0 & 4.2 0 & 2.8
St-1-WH4 0 8.19 0.93 100 0 0.00 0 0& 0 0& 0

DESIGN FOR LATERAL WIND FORCES

1903 2987 1250


BRACING
WH1
BRACING

WV1
WV2 WV3
2258
W2 D2
4102
BRACING

BRACING
WH2 JOIST J1
JOIST J3
BRACING

1842 DW1
D2

BRACING 7689
589 W3 D1 WH3
500
BRACING

WV5
W1 JOIST J2 3587
3000 WV4

WH4
1
BRACING

3600

4890
Y DIRECTION

X DIRECTION
PLAN SHOWING LATERAL LOAD BRACING ( IN GREEN)
Referring to Wind Load Calculation Sheet
Design Wind Pressure Vb= 1.10 KN/m2
Maximum Global Pressure Co-effcinet in X Direction 0.95
Maximum Global Pressure Co-effcinet in Y Direction 0.80

Wind Pressure in X Direction= 1.042686 KN/m2


Wind Pressure in Y Direction= 0.878051 KN/m2
WIND SHEAR COMPUTATION IN X DIRECTION
Width of Exposure in X Direction= 7.689 m
Wind Force at Roof Eave Level= 26 KN 1.7
Wind Force ar Second Floor Level= 27 KN
Wind Force ar FirstFloor Level= 29 KN

26 3
26 KN

29

55 KN
3.5 All Dim in Meter

29

84 KN

3.5
Therefore Shear Force at
First Floor Level= 84 KN
Second Flolor Level= 55 KN
Roof Level= 26 KN
SIMILARLY WIND SHEAR COMPUTATION IN Y DIRECTION
Width of Exopure in Y Direction= 4.89 m
First Floor Level= 43 KN
Second Flolor Level= 29 KN
Roof Level= 16 KN

LOAD SHARED BY BRACING IN X DIRECTION LOAD SHARED BY BRACING IN Y DIRECTION


Name of Wall Frame Tributary Load Name of Wall Frame Tributary Load
with Bracing Cad Wall Width of Shared By with Bracing Cad Wall Width of Shared By
No Bracing in Bracing in No Bracing in Bracing in
Meter KN Meter KN

St-1-WH1 1.13 12.33 St-1-WV1 0.95 8.37


St-1-WH2 2.05 22.40 St-1-WV2 1.22 10.75
St-1-WH3 2.72 29.67 St-1-WV2A 1.22 10.75
St-1-WH4 1.79 19.59 St-1-WV3 1.49 13.13
TOTAL= 7.69 83.99 4.89 43.00
St-2-WH1 1.13 8.08 St-2-WV1 0.95 5.64
St-2-WH2 2.05 14.66 St-2-WV2 1.22 7.25
St-2-WH3 2.72 19.42 St-2-WV2A 1.22 7.25
St-2-WH4 1.79 12.83 St-2-WV3 1.49 8.86
TOTAL= 7.69 54.99 4.89 29.00
St-3-WH1 1.13 3.82 St-3-WV1 0.95 3.11
St-3-WH2 2.05 6.93 St-3-WV2 1.22 4.00
St-3-WH3 2.72 9.18 St-3-WV2B 1.22 4.00
St-3-WH4 1.79 6.06 St-3-WV3 1.49 4.89
TOTAL= 7.69 26.00 4.89 16.00
DETAILED DESIGN OF LATERAL BRACING FOR WIND
Bracing on Wall St-1-WH3
Spacing of Stud= 0.407 m
Dead Load Udl= 8.97 KN/m
Live Roof Udl= 0.22 KN/m
Live FloorUdl= 1.63 KN/m
Wind Thrust= 0.04 KN/m
Wind Uplift= -0.40 KN/m
Lat FORCE= 29.67 KN
SERVICE AXIAL FORCES ON STUDS
DL
3.65 3.65 3.65 3.65

LLFloor 0.66 0.66 0.66 0.66

LLRoof
0.09 0.09 0.09 0.09

WL Thrust
0.02 0.02 0.02 0.02

WL Uplift -0.16 -0.16 -0.16 -0.16

LAT
29.67

3100

3629.155411 mm

48.73590397
1887

SIN= 0.8541932
COS= 0.5199557 57.05489343
TAN= 1.6428193 48.7359

T= 57.054893 KN 29.66601639
C= 48.735904 KN

TOTAL AXIAL LOAD on STUD= 53.05

Comb 4 1.2 DL 1.0 LLFLOor 0.5 LLroof 1.0 WLthrust 1.0 WLLateral

Maximum Compression forces in Stud= 53.84 KN


Beding Moment on Stud due to Pressure= 0.64 KNm
Focre in Strap= 57.05 KN
Yield Strength of Strap Material= 550 N/mm2
Design Yeild Strengh of Strap Material= 495 N/mm2
No of Strap Bracing Provided= 2 Nos
Width of Strap Provided= 64 mm2
Thickness of Strap Provided= 1.2 mm
Area required= 115.26241 mm2
Provide Strap of= 2 Nos 64mm Wide 153.6 mm2
STRAP OK
Comnpression Capacity of Stud= 25.43 KN
Bending Capaccity of Stud= 1.92 KNm

No of Stud Provided as Collector Studs= 3 Nos

Interaction Ratio= 0.82

Comb 3 0.9 DL 0 0 0 0 1 WLuplift 1 WLLateral

Maximum UpliftForce forces in Stud= -45.62 KN


Type of Hold Down Provided= HTT5
No of Hold Down Provided= 2 Nos
Capacity of HoldDown= 24 KN
HOLD DOWN CAPACITY OK

ANALYSIS OF ALL WIND BRACINGS WALLS


WALL DETAIL Service Force ForceS For Strenght Design
FrameCad Name of Wall Stud Width of X Lateral Force in Compession/ Force in Compression Uplift Due Bending
Wall No With Bracing Spacing Brace Force Strap Tension in Strap Due in Stud Due to to Load on wall
Collector to Load Load Comb 4 Comb '3 Stud due
Stud Comb 4 to Wind
Pressure
St-1-WH1 0.407 1723 12.33 25.39 22.19 25.39 26.09 -19.62 0.64
St-1-WH2 0.407 1723 22.40 46.10 40.29 46.10 45.40 -37.17 0.87
St-1-WH3 0.407 1887 29.67 57.05 48.74 57.05 53.84 -45.62 0.87
St-1-WH4 0.407 3420 19.59 26.44 17.76 26.44 21.66 -15.19 0.64

St-2-WH1 0.407 1723 8.08 16.62 14.53 16.62 16.99 -12.91 0.64
St-2-WH2 0.407 1723 14.66 30.18 26.38 30.18 29.52 -24.49 0.87
St-2-WH3 0.407 1887 19.42 37.36 31.91 37.36 35.05 -30.02 0.87
St-2-WH4 0.407 3420 12.83 17.32 11.63 17.32 14.09 -10.01 0.64
0.00
St-3-WH1 0.407 1723 3.82 7.67 6.65 7.67 7.67 -5.99 0.60
St-3-WH2 0.407 1723 6.93 13.92 12.07 13.92 13.24 -11.41 0.81
St-3-WH3 0.407 1887 9.18 17.25 14.60 17.25 15.76 -13.94 0.81
St-3-WH4 0.407 3420 6.06 8.07 5.32 8.07 6.34 -4.66 0.60

St-1-WV1 0.407 2251 8.37 14.24 11.52 14.24 19.85 -6.93 0.64
St-1-WV2 0.407 1268 10.75 28.40 26.28 28.40 43.45 -17.66 0.87
St-1-WV2A 0.407 1268 10.75 28.40 26.28 28.40 43.45 -17.66 0.87
St-1-WV3 0.407 3407 13.13 17.76 11.95 17.76 30.89 -2.52 0.64
0.00 0.00
St-2-WV1 0.407 2251 5.64 9.60 7.77 9.60 12.71 -5.14 0.64
St-2-WV2 0.407 1268 7.25 19.15 17.72 19.15 27.61 -13.07 0.87
St-2-WV2A 0.407 1268 7.25 19.15 17.72 19.15 27.61 -13.07 0.87
St-2-WV3 0.407 3407 8.86 11.97 8.06 11.97 18.93 -3.00 0.64

St-3-WV1 0.407 2251 3.11 5.19 4.15 5.19 5.70 -3.48 0.60
St-3-WV2 0.407 1268 4.00 10.27 9.46 10.27 12.06 -8.78 0.81
St-3-WV2B 0.407 1268 4.00 10.27 9.46 10.27 12.06 -8.78 0.81
St-3-WV3 0.407 3407 4.89 6.51 4.30 6.51 7.11 -3.62 0.60

DESIGN OF ALL WIND BRACINGS WALLS


Axial Capacity of Top Story Stud= 26.49 KN
Bending Capacity of Top Storey Stud= 1.92 KNm
Axial Capacity of General Floor Stud= 25.43 KN
Bending Capacity of General Storey Stud= 1.92 KNm
Screw Capacity= 2.65 KN
Hold Down Capacity of HTT4= 12 KN
Hold Down Capacity of HTT5= 24 KN
Wall No of Intearctio No Strap Strap Strap Forc Vs No of No of Hold Type of Uplift Vs
Name Collector Stud n Ratio Width Thickness Capacity Srew Down Provide Hold Capacity
Provided Ratio of Required Down of Hold
Strap on Each Down
Side Ratio
St-1-WH1 2.00 0.66 2.00 32.00 1.20 0.67 5 2 HTT4 0.82
St-1-WH2 3.00 0.72 2.00 64.00 1.20 0.61 9 2 HTT5 0.77
St-1-WH3 3.00 0.83 2.00 64.00 1.20 0.75 11 2 HTT5 0.95
St-1-WH4 2.00 0.58 2.00 32.00 1.20 0.70 5 2 HTT4 0.63

St-2-WH1 2.00 0.50 1.00 32.00 1.20 0.87 7 2 HTT4 0.54


St-2-WH2 2.00 0.81 2.00 64.00 1.20 0.40 6 2 HTT5 0.51
St-2-WH3 2.00 0.92 2.00 64.00 1.20 0.49 8 2 HTT5 0.63
St-2-WH4 2.00 0.44 1.00 32.00 1.20 0.91 7 1 HTT4 0.83

St-3-WH1 2.00 0.31 1.00 32.00 1.20 0.40 3 1 HTT4 0.50


St-3-WH2 2.00 0.47 1.00 32.00 1.20 0.73 6 1 HTT4 0.95
St-3-WH3 2.00 0.52 1.00 32.00 1.20 0.91 7 1 HTT4 1.16
St-3-WH4 2.00 0.28 1.00 32.00 1.20 0.42 4 1 HTT4 0.39

St-1-WV1 2.00 0.54 1.00 32.00 1.20 0.75 6 1 HTT4 0.58


St-1-WV2 3.00 0.70 2.00 32.00 1.20 0.75 6 2 HTT4 0.74
St-1-WV2A 3.00 0.70 2.00 32.00 1.20 0.75 6 2 HTT4 0.74
St-1-WV3 2.00 0.75 1.00 32.00 1.20 0.93 7 1 HTT4 0.21

St-2-WV1 2.00 0.42 1.00 32.00 1.20 0.51 4 1 HTT4 0.43


St-2-WV2 2.00 0.77 2.00 32.00 1.20 0.50 4 1 HTT4 1.09
St-2-WV2A 2.00 0.77 2.00 32.00 1.20 0.50 4 1 HTT4 1.09
St-2-WV3 2.00 0.54 1.00 32.00 1.20 0.63 5 1 HTT4 0.25

St-3-WV1 2.00 0.27 1.00 32.00 1.20 0.27 2 1 HTT4 0.29


St-3-WV2 2.00 0.45 1.00 32.00 1.20 0.54 4 1 HTT4 0.73
St-3-WV2B 2.00 0.45 1.00 32.00 1.20 0.54 4 1 HTT4 0.73
St-3-WV3 2.00 0.30 1.00 32.00 1.20 0.34 3 1 HTT4 0.30

SERVICEABILITY DESIGN OF ALL WIND BRACINGS WALLS

Allowable Storey Drift for Wind Load= L/300 L/= 300


E of Steel= 200000 N/mm2
Wall Strap Focres in Area of Lenght of Axial Lateral Permissibe Ratio of
Name KN Strap in Strap in mm extension Extension Storey Drift Storey
mm2 A of Strap in of Strap Drift to
mm .cos Permsble
=PL/AE Storey
Drift
St-1-WH1 25.39 76.8 3546.65 5.86 2.85 10.33 0.28
St-1-WH2 46.10 153.6 3546.65 5.32 2.59 10.33 0.25
St-1-WH3 57.05 153.6 3629.16 6.74 3.50 10.33 0.34
St-1-WH4 26.44 76.8 4615.89 7.95 5.89 10.33 0.57

St-2-WH1 16.62 38.4 3546.65 7.68 3.73 10.33 0.36


St-2-WH2 30.18 153.6 3546.65 3.48 1.69 10.33 0.16
St-2-WH3 37.36 153.6 3629.16 4.41 2.29 10.33 0.22
St-2-WH4 17.32 38.4 4615.89 10.41 7.71 10.33 0.75

St-3-WH1 7.67 38.4 3459.59 3.45 1.72 10.00 0.17


St-3-WH2 13.92 38.4 3459.59 6.27 3.12 10.00 0.31
St-3-WH3 17.25 38.4 3544.12 7.96 4.24 10.00 0.42
St-3-WH4 8.07 38.4 4549.33 4.78 3.59 10.00 0.36

St-1-WV1 14.24 38.4 3831.06 7.10 4.17 10.33 0.40


St-1-WV2 28.40 76.8 3349.30 6.19 2.34 10.33 0.23
St-1-WV2A 28.40 76.8 3349.30 6.19 2.34 10.33 0.23
St-1-WV3 17.76 38.4 4606.26 10.65 7.88 10.33 0.76

St-2-WV1 9.60 38.4 3831.06 4.79 2.81 10.33 0.27


St-2-WV2 19.15 76.8 3349.30 4.18 1.58 10.33 0.15
St-2-WV2A 19.15 76.8 3349.30 4.18 1.58 10.33 0.15
St-2-WV3 11.97 38.4 4606.26 7.18 5.31 10.33 0.51

St-3-WV1 5.19 38.4 3750.60 2.53 1.52 10.00 0.15


St-3-WV2 10.27 38.4 3256.97 4.36 1.70 10.00 0.17
St-3-WV2B 10.27 38.4 3256.97 4.36 1.70 10.00 0.17
St-3-WV3 6.51 38.4 4539.56 3.85 2.89 10.00 0.29

DESIGN FOR EARTH QUAKE FORCES


6090 650

Computation of Seismic Weight


Roof Area= 53.71 Sqm 4890 1250
SF Floor Area= 34.88 Sqm
FF Floor Area= 34.88 Sqm
Wall Lenght-Top Floor= 32.04 Meter 4102 5302
Wall Height for Top Floor= 3.00 Meter 5889
Wall Lenght-Top Floor= 32.04 Meter 4689
Wall Height for Top Floor= 3.10 Meter
Wall Lenght-Top Floor= 32.04 Meter
Wall Height for Top Floor= 3.10 Meter

Percent LiveLoad Be Considered= 25 % 3000


3000
3600

Height of Building= 10 m

Zone Factor Z= 0.36 4800


Importance Factor I= 1.0
Response Reduction Factor = 4.0
Time Period of The Building T=0.085H0.75= 0.47799
Sa/g= 2.5 For Medium Soil
Hor Seism Co-eff Ah=Z/2*I/R*Sa/g = 0.1125
Multiplying Factor for 2 % Damping= 1.4
Seismic Co-ff for Steel Building= 0.1575

Level Seismic Floor Height WiHi2 Percent Seismic Force


Weigh Wi Hi in Meter Force in Each Lvl in
in KN Shared by KN
Lvl
Eave Lvl 89.02 10 8902.2002 0.45315 31.39
SF Lvl 175.40 7 8594.3594 0.43748 30.30
FF Lvl 175.40 3.5 2148.5899 0.10937 7.58 1.7
2
Seis Weight= 439.81 WiHi = 19645.15 31.39
Base Shear= 69.27042 KN
3
31.39
31.38989 KN
30.30

30.30
3.5
61.69431 KN
7.58

7.58
3.5
69.27 KN

STOREY SHEAR DIAGRAM(SEISMIC)

Therefore Shear Force at


First Floor Level= 69.27 KN
Second Flolor Level= 61.69 KN
Roof Level= 31.39 KN

LOAD SHARED BY BRACING IN X DIRECTION LOAD SHARED BY BRACING IN Y DIRECTION


Name of Wall Frame Tributary Load Name of Wall Frame Tributary Load
with Bracing Cad Wall Width of Shared By with Bracing Cad Wall Width of Shared By
No Bracing in Bracing in No Bracing in Bracing in
Meter KN Meter KN

St-1-WH1 1.13 10.17 St-1-WV1 0.00 0.95 13.48


St-1-WH2 2.05 18.47 St-1-WV2 1.22 17.32
St-1-WH3 2.72 24.47 St-1-WV2A 1.22 17.32
St-1-WH4 1.79 16.16 St-1-WV3 1.49 21.16
TOTAL= 7.69 69.27 4.89 69.27
St-2-WH1 1.13 9.06 St-2-WV1 0.95 12.00
St-2-WH2 2.05 16.45 St-2-WV2 1.22 15.42
St-2-WH3 2.72 21.79 St-2-WV2A 1.22 15.42
St-2-WH4 1.79 14.39 St-2-WV3 1.49 18.84
TOTAL= 7.69 61.69 4.89 61.69
St-3-WH1 1.13 4.61 St-3-WV1 0.95 6.11
St-3-WH2 2.05 8.37 St-3-WV2 1.22 7.85
St-3-WH3 2.72 11.09 St-3-WV2B 1.22 7.85
St-3-WH4 1.79 7.32 St-3-WV3 1.49 9.59
TOTAL= 7.69 31.39 4.89 31.39

ANALYSIS OF ALL SEISMICE BRACINGS Of WALLS

WALL DETAIL Service Force ForceS For Strenght Design


FrameCad Name of Wall Stud Width of X Lateral Force in Compession/ Force in Compression Uplift Due
Wall No With Bracing Spacing Brace Force Strap Tension in Strap Due in Stud Due to to Load
Collector to Load Load Comb 6 Comb 5
Stud Comb 6

St-1-WH1 0.407 1723 10.17 20.94 18.30 20.94 24.85 -17.40


St-1-WH2 0.407 1723 18.47 38.02 33.23 38.02 43.15 -33.64
St-1-WH3 0.407 1887 24.47 47.06 40.20 47.06 52.19 -42.68
St-1-WH4 0.407 3420 16.16 21.81 14.65 21.81 25.72 -18.27

St-2-WH1 0.407 1723 9.06 18.65 16.30 18.65 18.65 -18.65


St-2-WH2 0.407 1723 16.45 33.86 29.60 33.86 37.03 -31.81
St-2-WH3 0.407 1887 21.79 41.91 35.80 41.91 45.07 -39.85
St-2-WH4 0.407 3420 14.39 19.43 13.05 19.43 21.90 -17.73

St-3-WH1 0.407 1723 4.61 9.26 8.03 9.26 10.29 -8.51


St-3-WH2 0.407 1723 8.37 16.81 14.57 16.81 18.00 -15.98
St-3-WH3 0.407 1887 11.09 20.82 17.63 20.82 22.02 -20.00
St-3-WH4 0.407 3420 7.32 9.74 6.42 9.74 10.78 -9.00
St-1-WV1 0.407 2251 13.48 22.94 18.56 22.94 31.33 -16.31
St-1-WV2 0.407 1268 17.32 45.74 42.34 45.74 63.08 -32.93
St-1-WV2A 0.407 1268 17.32 45.74 42.34 45.74 63.08 -32.93
St-1-WV3 0.407 3407 21.16 28.60 19.25 28.60 47.73 -14.56

St-2-WV1 0.407 2251 12.00 20.43 16.53 20.43 25.43 -17.42


St-2-WV2 0.407 1268 15.42 40.74 37.71 40.74 50.79 -35.11
St-2-WV2A 0.407 1268 15.42 40.74 37.71 40.74 50.79 -35.11
St-2-WV3 0.407 3407 18.84 25.48 17.14 25.48 36.53 -19.32

St-3-WV1 0.407 2251 6.11 10.18 8.14 10.18 11.79 -9.13


St-3-WV2 0.407 1268 7.85 20.16 18.57 20.16 22.92 -18.49
St-3-WV2B 0.407 1268 7.85 20.16 18.57 20.16 22.92 -18.49
St-3-WV3 0.407 3407 9.59 12.77 8.44 12.77 15.77 -10.99

DESIGN OF ALL SEISMIC BRACINGS WALLS


Axial Capacity of Top Story Stud= 26.49 KN
Bending Capacity of Top Storey Stud= 1.92 KNm
Axial Capacity of General Floor Stud= 25.43 KN
Bending Capacity of General Storey Stud= 1.92 KNm
Screw Capacity= 2.65 KN
Hold Down Capacity of HTT4= 12.00 KN
Hold Down Capacity of HTT5= 24.00 KN
Wall No of No Strap Strap Width Strap No of Type of Hold Forc Vs No of Srew Compress Uplift Vs
Name Collector Stud Thickness Hold Down Capacity Required on ion Capacity
Provided Down Ratio of Each Side Capacity of Hold
Provide Strap Ratio Down
Ratio

St-1-WH1 2.00 2.00 32.00 1.20 2.00 HTT4 0.55 4 0.49 0.73
St-1-WH2 3.00 2.00 100.00 1.20 2.00 HTT5 0.32 8 0.57 0.70
St-1-WH3 3.00 2.00 100.00 1.20 2.00 HTT5 0.40 9 0.68 0.89
St-1-WH4 2.00 2.00 32.00 1.20 2.00 HTT4 0.57 5 0.51 0.76

St-2-WH1 2.00 2.00 32.00 1.20 2.00 HTT4 0.49 4 0.37 0.78
St-2-WH2 2.00 2.00 100.00 1.20 2.00 HTT5 0.29 7 0.73 0.66
St-2-WH3 2.00 2.00 100.00 1.20 2.00 HTT5 0.35 8 0.89 0.83
St-2-WH4 2.00 2.00 32.00 1.20 1.00 HTT5 0.51 4 0.43 0.74

St-3-WH1 2.00 2.00 32.00 1.20 1.00 HTT4 0.24 2 0.19 0.71
St-3-WH2 2.00 2.00 32.00 1.20 2.00 HTT4 0.44 4 0.34 0.67
St-3-WH3 2.00 2.00 32.00 1.20 2.00 HTT4 0.55 4 0.42 0.83
St-3-WH4 2.00 1.00 32.00 1.20 1.00 HTT4 0.51 4 0.20 0.75

St-1-WV1 2.00 2.00 32.00 1.20 2.00 HTT4 0.60 5 0.62 0.68
St-1-WV2 3.00 2.00 100.00 1.20 2.00 HTT5 0.39 9 0.83 0.69
St-1-WV2A 3.00 2.00 100.00 1.20 2.00 HTT5 0.39 9 0.83 0.69
St-1-WV3 2.00 2.00 32.00 1.20 2.00 HTT4 0.75 6 0.94 0.61

St-2-WV1 2.00 2.00 32.00 1.20 2.00 HTT4 0.54 4 0.50 0.73
St-2-WV2 2.00 2.00 64.00 1.20 2.00 HTT5 0.54 8 1.00 0.73
St-2-WV2A 2.00 2.00 64.00 1.20 2.00 HTT5 0.54 8 1.00 0.73
St-2-WV3 2.00 2.00 32.00 1.20 2.00 HTT4 0.67 5 0.72 0.80

St-3-WV1 2.00 1.00 32.00 1.20 1.00 HTT4 0.54 4 0.22 0.76
St-3-WV2 2.00 2.00 32.00 1.20 2.00 HTT4 0.53 4 0.43 0.77
St-3-WV2B 2.00 2.00 32.00 1.20 2.00 HTT4 0.53 4 0.43 0.77
St-3-WV3 2.00 1.00 32.00 1.20 3.00 HTT4 0.67 5 0.30 0.31
SERVICEABILITY DESIGN OF ALL WIND BRACINGS WALLS

Allowable Storey Drift for Wind Load= L/250 L/= 250


E of Steel= 200000 N/mm2
Wall Strap Focres in Area of Lenght of Axial Lateral Permissibe Ratio of
Name KN Strap in Strap in mm extension Extension Storey Drift Storey
mm2 A of Strap in of Strap Drift to
mm .cos Permsble
=PL/AE Storey
Drift
St-1-WH1 20.94 76.8 3546.65 4.83 2.35 12.40 0.19
St-1-WH2 38.02 240 3546.65 2.81 1.36 12.40 0.11
St-1-WH3 47.06 240 3629.16 3.56 1.85 12.40 0.15
St-1-WH4 21.81 76.8 4615.89 6.55 4.86 12.40 0.39
12.40
St-2-WH1 18.65 76.8 3546.65 4.31 2.09 12.40 0.17
St-2-WH2 33.86 240 3546.65 2.50 1.22 12.40 0.10
St-2-WH3 41.91 240 3629.16 3.17 1.65 12.40 0.13
St-2-WH4 19.43 38.4 4615.89 11.67 8.65 12.40 0.70

St-3-WH1 9.26 38.4 3459.59 4.17 2.08 12.40 0.17


St-3-WH2 16.81 76.8 3459.59 3.79 1.89 12.40 0.15
St-3-WH3 20.82 76.8 3544.12 4.80 2.56 12.40 0.21
St-3-WH4 9.74 38.4 4549.33 5.77 4.34 12.40 0.35

St-1-WV1 22.94 76.8 3831.06 5.72 3.36 12.40 0.27


St-1-WV2 45.74 240 3349.30 3.19 1.21 12.40 0.10
St-1-WV2A 45.74 240 3349.30 3.19 1.21 12.40 0.10
St-1-WV3 28.60 76.8 4606.26 8.58 6.34 12.40 0.51

St-2-WV1 20.43 76.8 3831.06 5.10 2.99 12.40 0.24


St-2-WV2 40.74 153.6 3349.30 4.44 1.68 12.40 0.14
St-2-WV2A 40.74 153.6 3349.30 4.44 1.68 12.40 0.14
St-2-WV3 25.48 76.8 4606.26 7.64 5.65 12.40 0.46
12.40
St-3-WV1 10.18 38.4 3750.60 4.97 2.98 12.40 0.24
St-3-WV2 20.16 76.8 3256.97 4.27 1.66 12.40 0.13
St-3-WV2B 20.16 76.8 3256.97 4.27 1.66 12.40 0.13
St-3-WV3 12.77 115.2 4539.56 2.52 1.89 12.40 0.15

You might also like