Professional Documents
Culture Documents
The flow monitors must not be positioned in inductive or magnetic fields. Minimum distance The switchpoint should be adjusted on the scale of the flowswitch.
from iron parts : 10 mm.
Please noticethat he switch point is always the shutdown point. That means, the contact will
All connection sizes comply with the R-Norm (DIN 2999, part 1). Only suitable thread and open when the flow rate is decreasing to the adjusted switchpoint. So the NO opens in case
sealing material should be used for installation, otherwise the correct functioning of the of an alarm.
equipment may be affected.
BFS-30-O:
To avoid the risk of measure faults, the upstream line should be 10 x D and the downstream If not activated, the NO contact will be open. It closes if the flow reaches a pre-adjusted value.
line 5 x D (where D = internal diameter of the tube). a) Pull the contact towards the flow inlet side (NO contact closed)
b) Adjust the flow to the desired flowrate.
The highest accuracy will be reached by mounting the flow monitors vertically, with flow c) Slide the switch towards the outlet port, until it opens. Now switch the switchcase.
direction from bottom to the top.
When screwing the fittings, take care of the max. lengh of the threads. Too long threads 4. Maintenance
may cause damage of the flow monitor.
The flowmeters are free of maintenance because of the few mechanical parts. For security
(BFS-30-O: reason we advice to check the flowmeters from time to time.
When screwing the fittings, the flowmeter threads must be fixed with a spanner. Never
rotate the flowmeter connections inside the aluminium sleeve. This may cause leakage
or breaking of the glass.)
All model provided with a switch should be protected from electrical overload. Never exceed
the given maximum switch capacity, not even for short periods. The embedded reedswitch is
very sensitive for specifically inductive loads, which may occur at closing or opening and Art.-Nr.: 923-0269
which can up to 10 times the given nominal value of the coil. Use protecting relays or other Index B, Mittl. 141-2000
precautions in such cases. Barksdale GmbH
Dorn-Assenheimer Strasse 27
Our reedswitch are gold- rhodium-plated, which allow direct connecting to SPS - systems. D-61203 Reichelsheim / Germany Specifications are subject to
changes without notice.
Tel.: +49 - 60 35 - 9 49-0
Fax: +49 - 60 35 - 9 49-111 and 9 49-113
e-mail: Info@Barksdale.de
Web-Site: http://www.barksdale.de
1 2
5. Technical data: Dimensions (in mm)
L
Change over 500 V - 1,5 A - 50 VA 500 V - 1,5 A - 50 VA
(D) 21 21 21 17 14
Protection IP65 IP65 (L) 152 152 152 130 90
Materials brass stainl. steel bras stainl. steel Weight (g) 1100 1100 1100 1000 350
D
Float brass 1.4571 brass 1.4571
W
Spring 1.4310 1.4571 1.4310 1.4571
Seals Perbunan, Viton or EPDM
Accuracy 10% of FS 10% of FS
Electrical connection acc. to DIN 43650 or with 1 m cable
D
Temperatuer max. 120 C
(G) G 1/4 G 1/2 G 3/4 G1
Electrical data (hex) 34 34 34 40
Normally open 250 V - 3A - 100 VA () 40 40 40 40
(W) 68 68 68 68
L
Change over 500 V - 1,5 A - 50 VA
(D) 21 21 21 17
Protection IP65 (L) 152 152 152 130
Materials brass stainl. steel Weight (g) 1350 1350 1350 1200
D
Float brass 1.4571
W
Spring 1.4310 1.4571
Seals Perbunan, Viton or EPDM
Accuracy 10% of FS
Electrical connection acc. to DIN 43650 or with 1 m cable 1
3 4