Professional Documents
Culture Documents
Caepipe
Version 7.70
Client :
Project :
File Number :
Report Number :
Title :
Hanger report 1
Flange report 1
Support load summary 1
Anchor at Node 10 1
Anchor at Node 180 2
Hanger at Node 40 2
Hanger at Node 60 2
Hanger at Node 80 2
Hanger at Node 90 2
Hanger at Node 110 3
Hanger at Node 140 3
Hanger at Node 160 3
Load case = Operating (W+P1+T1) 3
Loads on anchors 3
Loads on hangers 3
Pipe forces (local coordinates) 4
Other forces (local coordinates) 5
Pipe forces (global coordinates) 5
Other forces (global coordinates) 6
Displacements 6
Version 7.70 caepipe Apr 8,2017
Caepipe TRABAJO PROYECTO MICHEL Page 1
Analysis Options
Code : Piping code = B31.1 (2016)
Do not include axial force in stress calculations
Do not use liberal allowable stresses
Temperature : Reference temperature = 70 (F)
Number of thermal cycles = 7000
Number of thermal loads = 1
Solve thermal case
Use modulus at reference temperature
Pressure : Pressure stress = PD / 4t
Peak pressure factor = 1.00
Do not include Bourdon effect
Do not use pressure correction for bends
Dynamics : Cut off frequency = 33 Hz
Number of modes = 20
Include missing mass correction
Do not use friction in dynamic analysis
Misc. : Include hanger stiffness
Vertical direction = Y
Hanger Report
Spring Vert Horz Hot Cold
Node No Type Figure Size rate travel travel load load Var
of No. (lb/inch) (inch) (inch) (lb) (lb) (%)
40 1 NPS Industries VL 7 56 1.999 0.129 441 553 25
60 1 NPS Industries VL 5 31 1.922 0.400 278 338 21
80 1 NPS Industries VL 8 75 1.485 0.283 650 761 17
90 1 NPS Industries VM 8 150 0.544 0.468 765 847 10
110 1 NPS Industries VM 5 63 -0.037 0.571 274 271 0
140 1 NPS Industries VM 6 84 -0.159 0.290 377 364 3
160 1 NPS Industries VM 3 35 -0.194 0.071 159 152 4
Flange report
Bending Axial Gasket Flange Allowable Flange
Node Pressure moment force diameter Pressure Pressure Pressure
(psi) (ft-lb) (lb) (inch) (psi) (psi) Allowable
30 300 117 0 4.026 410
20 300 31 0 4.026 329
Support load summary for anchor at node 10
Displaceme
Load combination FX (lb) FY (lb) FZ (lb) MX (ft-lb) MY (ft-lb) MZ (ft-lb) X (inch) Y (i
Sustained 0 171 -2 255 27 1065 0.000 0.0
Operating1 0 33 1 24 -16 128 0.000 2.0
Maximum 0 171 1 255 27 1065 0.000 2.0
Minimum 0 33 -2 24 -16 128 0.000 0.0
Version 7.70 caepipe Apr 18,2017
Caepipe TRABAJO PROYECTO MICHEL Page 2
Support load summary for anchor at node 10
Displaceme
Load combination FX (lb) FY (lb) FZ (lb) MX (ft-lb) MY (ft-lb) MZ (ft-lb) X (inch) Y (i
Allowables 0 0 0 0 0 0 0.000 0.0
Support load summary for anchor at node 180
Displaceme
Load combination FX (lb) FY (lb) FZ (lb) MX (ft-lb) MY (ft-lb) MZ (ft-lb) X (inch) Y (i
Sustained 0 -49 2 -108 24 120 0.000 0.0
Operating1 0 -32 -1 -47 -17 -18 0.000 -0.1
Maximum 0 -32 2 -47 24 120 0.000 0.0
Minimum 0 -49 -1 -108 -17 -18 0.000 -0.1
Allowables 0 0 0 0 0 0 0.000 0.0
Support load summary for hanger at node 40
Displacements (global)
Load combination Load (lb) X (inch) Y (inch) Z (inch)
Sustained -549 0.000 0.072 -0.003
Operating1 -441 0.129 1.999 0.002
Maximum -441 0.129 1.999 0.002
Minimum -549 0.000 0.072 -0.003