You are on page 1of 17

EXPORT CONTROLLED SERVICE

BULLETIN

AIR -- SINGLE-UNIT COMPRESSOR ACCELERATION BLEED VALVE


CONFIGURATION
1. PLANNING INFORMATION

A. Effectivity
(1) Engines
All AE 3007C and AE 3007C1 engines.
NOTE: The engine serial numbers that are affected by this service bulletin have not been
established. This service bulletin will be revised when engine production records
for this modification are recorded, and engine serial number effectivity for in
service engines are established.
(2) Spares -- Not affected

B. Reason
This service bulletin introduces a new compressor acceleration bleed system that decreases
maintenance requirements and has better resistance to contamination.
The new compressor acceleration bleed system has a new, single compressor acceleration
bleed valve (CABV) installed on the bottom of the engine for easy access. The new compressor
acceleration bleed system has a compressor acceleration bleed control valve (CABCV) as an
integral part of the single CABV. The new compressor acceleration bleed system also
eliminates an external CABCV and its associated hardware, tubes, and brackets.

C. Description
This service bulletin gives you the procedure to remove the compressor acceleration bleed
system with the associated hardware and install the new single-unit compressor acceleration
bleed system.

D. Approval
Technical aspects are FAA approved.

E. Manpower
(1) In Service: Approximately 10.0 man--hours per engine are necessary to do this service
bulletin.
(2) Engine Removed: Approximately 8.0 man--hours per engine are necessary to do this
service bulletin.
(3) Authorized Maintenance Center: Approximately 3.0 man--hours per engine are necessary
to do this service bulletin.

F. Compliance
This service bulletin is optional. This service bulletin can be accomplished with the engine
installed on the aircraft.

G. Interchangeability -- Not affected


December 21, 2006 AE 3007C--75--034

Page 1 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN
H. Material Availability

NEW P/N NAME QTY/ENG UNIT PRICE


U.S.
DOLLARS
*MS9142--041 Gasket, Metal O--ring 1.375 OD X 0.063 THK 1 $3.58
*23038910 Cover, Customer Bleed Port, Compressor 1 323.45
23075314 Parts Kit, Adapter, Acceleration Bleed Valve 1 10,398.19
(PRE--SB AE 3007C--72--236 configuration)
23075810 Valve Assy, Air Bleed -- Compressor Acceleration 1 5,329.50
23083593 Parts Kit, Adapter, Acceleration Bleed Valve 1 10,398.19
(POST--SB AE 3007C--72--236 configuration)

*Parts needed for engine that has not complied with one of the service bulletins that follow:
-- AE 3007C--72--162
-- AE 3007C--75--012
-- AE 3007C--75--020.
Unit prices listed in this service bulletin are valid when the service bulletin is published. Unit
prices are subject to change. Contact your Account Representative at Rolls-Royce Supply
Services for current unit prices.
Contact your Account Representative at Rolls-Royce Supply Services for parts availability as
follows:

Mailing Address: Rolls-Royce Corporation


P. O. Box 420
Indianapolis, Indiana 46206--0420
USA
Attention: Supply Services
Speed Code R39

Telephone: 317--230--2016
FAX: 317--230--8899
I. Tooling -- Not applicable

J. Weight and Balance


Engine weight will decrease by 1.8 lb (816 g) when you incorporate this bulletin with parts kit
(23075314).
Engine weight will decrease by 2.0 lb (907 g) when you incorporate this bulletin with parts kit
(23083593).
K. Electrical Load Data -- Not affected

L. References
(1) Advance Engineering Memorandum (AEM), CN118816.
NOTE: The document above is referenced for the internal use of Rolls-Royce only.
(2) AE 3007C Series Illustrated Parts Catalog (IPC), CSP33001.
(3) AE 3007C Series Maintenance Manual (MM), CSP34012.
(4) Service Bulletin AE 3007C--72--162, Engine -- New Start Bleed Valve Support Bracket Kit
(23074437).
December 21, 2006 AE 3007C--75--034

Page 2 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN
(5) Service Bulletin AE 3007C--72--221, Engine -- Change the Location of the Compressor
Vibration Accelerometer.
(6) Service Bulletin AE 3007C--72--236, Engine -- New Right and Left Hand Coverplates and
Transfer Tubes.
(7) Service Bulletin AE 3007C--75--001, Air -- Improved Engine Bleed Control System.
(8) Service Bulletin AE 3007C--75--002, Air -- Replace the 8th Stage Customer Bleed Tube and
Support Brackets.
(9) Service Bulletin AE 3007C--75--012, Air -- New Start Bleed Control--Valve Assembly.
(10) Service Bulletin AE 3007C--75--017, Air -- Bleed Control Tube -- Clamping.
(11) Service Bulletin AE 3007C--75--020, Air -- New Start Bleed Control Valve Support Bracket
and Inlet Flexible Tube.

M. Other Publications Affected


(1) AE 3007C Series Illustrated Parts Catalog (IPC), CSP33001.
(2) AE 3007C Series Maintenance Manual (MM), CSP34012.
(3) AE 3007 Series Engine Manual (EM), CSP31010.

N. Prerequisites -- None
O. Corequisites -- None

2. ACCOMPLISHMENT INSTRUCTIONS
CAUTION: IN ORDER TO REDUCE THE POTENTIAL FOR MULTIPLE--ENGINE IN--FLIGHT
SHUTDOWN, POWER LOSS, OR OTHER ANOMALY DUE TO MAINTENANCE ERROR,
ROLLS--ROYCE RECOMMENDS THAT OPERATORS AVOID PERFORMING
MAINTENANCE ON MULTIPLE ENGINES INSTALLED ON THE SAME AIRCRAFT AT
THE SAME TIME. IF IT IS NOT POSSIBLE TO AVOID MAINTENANCE ON MORE THAN
ONE ENGINE AT THE SAME TIME, ROLLS--ROYCE RECOMMENDS THAT
ADDITIONAL CONTROLS ARE APPLIED IN ORDER TO ENSURE THAT MAINTENANCE
TASKS HAVE BEEN COMPLETED AS DEFINED. MAINTENANCE GUIDELINES
SHOULD BE REVISED, WHERE POSSIBLE, TO PROMOTE THIS RECOMMENDATION.
A. Remove the compressor air bleed components and tubes.
REF. FIG. 1
(1) Remove the upper bleed--air--valve bleed--air control tube (Ref. SUBTASK
75--00--00--020--002, MM).
(2) Remove the compressor acceleration--bleed--control valve--to--line--tee tube (CABCV tube).
(Ref. SUBTASK 75--00--00--020--003, MM).

December 21, 2006 AE 3007C--75--034

Page 3 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN
(3) Remove the line--tee--to--service--manifold tube.
PRE--SB AE 3007C--72--236
(a) Remove the line--tee--to--service--manifold tube (Ref. SUBTASK 75--00--00--020--004,
MM).
POST--SB AE 3007C--72--236
(a) Remove the line--tee--to--service--manifold tube (Ref. SUBTASK 75--00--00--020--013,
MM).
(b) Remove the nut (11) that attaches the bracket (12) to the compressor case bleed
manifold at the 7 oclock position. Remove the bracket and attached components.
WARNING: DO NOT GET THE ANTISEIZE COMPOUND ON YOUR SKIN OR
BREATHE THE VAPORS. IT IS POISONOUS. IF YOU GET IT ON YOUR
SKIN, CLEAN WITH SOAP AND WATER. IF YOU GET IT IN YOUR EYES,
FLUSH WITH WATER. GET MEDICAL AID.
(c) Apply the antiseize compound (NSN--165) to the threads of the stud (13) on the
compressor case bleed manifold.
(d) Install the nut (11) on the stud (13). Use the torque wrench to torque the nut (11) to
74--89 in--lb (8.4--10.0 Nm) (Ref. TASK 70--00--00--910--801, MM).
(4) Remove the bleed--control transfer tube.
POST--SB AE 3007C--72--236
(a) Remove the bleed--control transfer tube (23076606) (Ref. SUBTASK
75--00--00--020--008, MM).
(5) Remove the diffuser--to--compressor acceleration--bleed--control valve tube.
PRE--SB AE 3007C--75--020
(a) Remove the diffuser--to--compressor acceleration--bleed--control valve tube (Ref.
SUBTASK 75--00--00--020--005, MM).
POST--SB AE 3007C--75--020
(a) Remove the diffuser--to--compressor acceleration--bleed--control valve tube (flexible
tube) (Ref. SUBTASK 75--00--00--020--006, MM).
(6) Remove the compressor acceleration--bleed--control valve (Ref. TASK
75--31--15--000--801, MM).
(7) Remove the upper compressor--acceleration bleed valve (Ref. TASK 75--31--10--000--801,
MM).
(8) Remove the lower compressor--air bleed valve (Ref. TASK 75--31--10--000--802, MM).
(9) Remove the compressor--bleed--valve adapter (Ref. TASK 75--31--25--000--801, MM).
B. Remove the hardware from compressor.
REF. FIG. 1
(1) Remove the strap bracket.
POST--SB AE 3007C--72--221
(a) Remove the nut (1) and bolt (3) that attach the strap bracket (7) at position H34.
Remove the strap bracket.
POST--SB AE 3007C--72--162
(a) Remove the nut (1) and bolt (3) that attach the strap bracket (7) at position H26.
Remove the strap bracket.
December 21, 2006 AE 3007C--75--034

Page 4 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN
(2) Remove the line support bracket.
POST--SB AE 3007C--75--001
POST--SB AE 3007C--75--020
(a) Remove the two nuts (1) and two bolts (3) that attach the line support bracket (2)
(23061722) at positions H32 and H33. Remove the bracket.
(3) Remove the two nuts (1) and two bolts (3) that attach the bleed valve adapter bracket (10)
(23056819) at positions H18 and H20. Remove the bracket.
(4) Remove the compressor acceleration--bleed--control valve bracket (Ref. TASK
75--31--15--000--802, MM). Remove the bracket.
(5) Remove the nut (1) and bolt (3) at position H17.
(6) Remove the bleed tube support bracket.
POST--SB AE 3007C--75--002
(a) Remove the bolt (5) that attaches the bleed control tube support bracket (6) and
saddle clamp (8) to the bleed tube support bracket (9). Remove the bleed control
tube support bracket.
POST--SB AE 3007C--75--017
(a) Remove the bolt (5) that attaches the line support bracket (4) and saddle clamp (8) to
the bleed tube support bracket (9). Remove the line support bracket.
C. Install the hardware on the compressor and diffuser.
REF. FIG. 2
WARNING: DO NOT GET THE ANTISEIZE COMPOUND ON YOUR SKIN OR BREATHE
THE VAPORS. IT IS POISONOUS. IF YOU GET IT ON YOUR SKIN, CLEAN
WITH SOAP AND WATER. IF YOU GET IT IN YOUR EYES, FLUSH WITH
WATER. GET MEDICAL AID.
(1) Install hardware on the diffuser.
PRE--SB AE 3007C--72--162
PRE--SB AE 3007C--75--012
PRE--SB AE 3007C--75--020
(a) Apply the antiseize compound (NSN--165) to the threads of the three studs (25) on the
compressor diffuser port.
(b) Put the new metal O--ring gasket (21) (MS9142--041) on the compressor diffuser port.
(c) Install the new compressor customer bleed port cover (23) (23038910) on the diffuser.
(d) Install the three nuts (22) (AS3066--09) on the studs (25). Use the torque wrench to
torque the three nuts to 37--42 in--lb (4.2--4.7 Nm) (Ref. TASK 70--00--00--910--801,
MM).
POST--SB AE 3007C--72--162
POST--SB AE 3007C--75--012
POST--SB AE 3007C--75--020
(a) Install the new cap (30) (AN929--4J) on the fitting (29) of the diffuser. Use the torque
wrench to torque the cap to 80--120 in--lb (9.1--13.5 Nm) (Ref. TASK
70--00--00--910--801, MM).
December 21, 2006 AE 3007C--75--034

Page 5 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN
(2) Install the hardware on the compressor--diffuser flange.
POST--SB AE 3007C--72--221
(a) Apply the antiseize compound (NSN--165) to the threads of the bolt (24).
(b) Install the bolt (24) and nut (20) at position H34. Use the torque wrench to torque the
nut to 74--89 in--lb (8.4--10.0 Nm) (Ref. TASK 70--00--00--910--801, MM).
POST--SB AE 3007C--75--001
POST--SB AE 3007C--75--020
(a) Apply the antiseize compound (NSN--165) to the threads of the two bolts (24).
(b) Install the two bolts (24) and two nuts (20) at positions H32 and H33. Use the torque
wrench to torque the nuts to 74--89 in--lb (8.4--10.0 Nm) (Ref. TASK
70--00--00--910--801, MM).
POST--SB AE 3007C--72--162
(a) Apply the antiseize compound (NSN--165) to the threads of the bolt (24).
(b) Install the bolt (24) and nut (20) at position H26. Use the torque wrench to torque the
nut to 74--89 in--lb (8.4--10.0 Nm) (Ref. TASK 70--00--00--910--801, MM).
(3) Apply the antiseize compound (NSN--165) to the threads of the three bolts (24).
(4) Install the three bolts (24) and three nuts (20) at positions H18, H28 and H29. Use the
torque wrench to torque the nuts to 74--89 in--lb (8.4--10.0 Nm) (Ref. TASK
70--00--00--910--801, MM).
(5) Install the new bleed valve mounting bracket (28) (23074441) on the compressor--diffuser
flange.
(a) Apply the antiseize compound (NSN--165) to the threads of the two bolts (24).
(b) Install the two bolts (24) and two nuts (20) that attach the bleed valve mounting
bracket (28) at positions H17 and H20. Use the torque wrench to torque the nuts to
74--89 in--lb (8.4--10.0 Nm) (Ref. TASK 70--00--00--910--801, MM).
(6) Install the hardware on the compressor.
POST--SB AE 3007C--75--002
POST--SB AE 3007C--75--017
(a) Apply the antiseize compound (NSN--165) to the threads of the bolt (26)
(MS9696--06).
(b) Install the bolt (26) that attaches the saddle clamp (31) to the bleed tube support
bracket (27). Use the torque wrench to torque the bolt to 37--42 in--lb (4.2--4.7 Nm)
(Ref. TASK 70--00--00--910--801, MM).
D. Install the new compressor acceleration bleed system.
REF. FIG. 3
REF. FIG. 4
REF. FIG. 5
(1) Install the new upper acceleration bleed port cover (cover) (41) (23074440).
(a) Apply the antiseize compound (NSN--165) to the threads of the three new bolts (40)
(MS9557--10).
(b) Install the three bolts (40) and three new nuts (43) (AS3477--10) that attach the
customer services core manifold (45), new gasket (42) (23074928) and cover (41) to
the bracket (44). Use the torque wrench to torque the three nuts to 37--42 in--lb
(4.2--4.7 Nm) (Ref. TASK 70--00--00--910--801, MM).
December 21, 2006 AE 3007C--75--034

Page 6 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN
(2) Install the new lower acceleration bleed valve adapter (adapter) (23074439) on the
compressor mounting flange (Ref. TASK 75--31--25--400--801, MM).
(a) Apply the antiseize compound (NSN--165) to the threads of the three bolts (50).
(b) Install the three bolts (50) that attach the adapter (49) and new gasket (48)
(23073460) to the compressor mounting flange (47).
(c) Install the customer bleed--air tube (53) on the adapter (49) (Ref. SUBTASK
75--00--00--420--001, MM). Use a new seal retainer (51) (23062486--32) and spiral
retaining ring (52) (AS3217--163).
(d) Use the torque wrench to torque the three bolts (50) to 74--89 in--lb (8.4--10.0 Nm)
(Ref. TASK 70--00--00--910--801, MM).
(3) Install the new CABV assembly (55) (23075810).
(a) Apply the antiseize compound (NSN--165) to the threads of the four bolts (54) installed
on the CABV assembly (55).
NOTE: The four bolts are held captive and are part of the CABV assembly.
(b) Install the two top bolts (54) that attach the CABV assembly (55) and adapter (49) to
the new bleed valve mounting bracket (46) (23074441).
(c) Install the two bottom bolts (54) that attach the CABV assembly (55) to the adapter
(49).
(d) Use the torque wrench to torque the four bolts (54) to 74--89 in--lb (8.4--10.0 Nm) (Ref.
TASK 70--00--00--910--801, MM).
(4) Install the new air bleed control tube.
PRE--SB AE 3007C--72--236
(a) Connect the fittings of the new air bleed control tube (64) (23074438) to the CABV
assembly (69) and service manifold (65). Use the torque wrench to torque the fittings
of the tube to 80--120 in--lb (9.1--13.5 Nm) (Ref. TASK 70--00--00--910--801, MM).
(b) Apply the antiseize compound (NSN--165) to the threads of the bolt (63)
(MS9696--06).
(c) Install the clamp (62) (23060015--04) on the air bleed control tube (64).
(d) Install the bolt (63) that attaches the clamp (62) and angle bracket (60) to the line
support bracket (61). Use the torque wrench to torque the bolt to 37--42 in--lb (4.2--4.7
Nm) (Ref. TASK 70--00--00--910--801, MM).
(e) Apply the antiseize compound (NSN--165) to the threads of the stud (68).
(f) Install the mending plate (67) on the stud (68).
(g) Install the nut (66) on the stud (68). Use the torque wrench to torque the nut to 37--42
in--lb (4.2--4.7 Nm) (Ref. TASK 70--00--00--910--801, MM).

December 21, 2006 AE 3007C--75--034

Page 7 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN
POST--SB AE 3007C--72--236
(a) Connect the fittings of the new TFE hose (85) (MS8005E214AC or 6886430E214AC)
to the CABV assembly (92) and the fitting on engine service coverplate (87). Use the
torque wrench to torque the fittings of the hose to 80--120 in--lb (9.1--13.5 Nm) (Ref.
TASK 70--00--00--910--801, MM).
(a) Install the new clamp (84) (23060015--06) on the TFE hose (85).
(b) Install the new clamp (88) (23037873--32) on the tube (93).
(c) Apply the antiseize compound (NSN--165) to the threads of the new bolt (83)
(MS9696--06).
(d) Install the bolt (83) and new nut (86) (AS3477--09) that attach the clamps (88 and 84).
Use the torque wrench to torque the nut to 37--42 in--lb (4.2--4.7 Nm) (Ref. TASK
70--00--00--910--801, MM).
(e) Apply the antiseize compound (NSN--165) to the threads of the bolt (82)
(MS9696--06).
(f) Install the bolt (82) that attaches the angle bracket (80) to the line support bracket
(81). Use the torque wrench to torque the bolt to 37--42 in--lb (4.2--4.7 Nm) (Ref.
TASK 70--00--00--910--801, MM).
(g) Apply the antiseize compound (NSN--165) to the threads of the stud (91).
(h) Install the mending plate (90) on the stud (91).
(i) Install the nut (89) on the stud (91). Use the torque wrench to torque the nut to 37--42
in--lb (4.2--4.7 Nm) (Ref. TASK 70--00--00--910--801, MM).
E. Install the left--hand inner duct (Ref. TASK 72--71--10--400--801, MM).
F. Install the access cover for the outer bypass duct (Ref. TASK 72--73--10--400--801, MM).
G. Do the test of the engine (Ref. TASK 72--00--00--700--801, MM).
H. Return the removed parts with the attached Parts Return Report to the following address:
Rolls-Royce Corporation
C/O UPS -- SCS
Returns Processing Center
2840 Fortune Circle West Drive
Dock Door 16
Indianapolis, Indiana 46241
USA
I. Record compliance with this service bulletin in the applicable section of the engine logbook.

December 21, 2006 AE 3007C--75--034

Page 8 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN

Compressor Hardware -- Removal


FIG. 1
December 21, 2006 AE 3007C--75--034

Page 9 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN

Compressor and Diffuser Hardware -- Installation


FIG. 2
December 21, 2006 AE 3007C--75--034

Page 10 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN

Single-unit Compressor Acceleration Bleed Valve -- Installation


FIG. 3
December 21, 2006 AE 3007C--75--034

Page 11 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN

Air Bleed Control Tube (PRE--SB AE 3007C--72--236) -- Installation


FIG. 4
December 21, 2006 AE 3007C--75--034

Page 12 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN

TFE Hose (POST--SB AE 3007C--72--236) -- Installation


FIG. 5
December 21, 2006 AE 3007C--75--034

Page 13 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN
3. MATERIAL INFORMATION

A. Configuration Chart
*Included in Compressor Acceleration Bleed Valve Adapter Parts Kit (23075314).
#Included in Compressor Acceleration Bleed Valve Adapter Parts Kit (23083593).

QTY/ QTY/ INSTRUCTIONS/


NEW P/N ENG NAME OLD P/N ENG DISPOSITION
#*23074441 1 Bracket, Mounting Bleed 23056819 1 1
Valve
-- -- Bracket Assy, Line 23062694 1 3
Support 23062499 1
23060139 1
-- -- Bracket, Strap -- Holes 26, 23073966 2 3
34
-- -- Bracket, Line Support -- 23061722 2 5
Holes 28, 29, 32, 33
-- -- Valve Assy, Compressor 23074337 1 2
Acceleraton Bleed Control 23052650 1
#*23073460 1 Gasket, Compressor -- -- 1
Bleed Manifold
#*23074439 1 Adapter, Acceleration 23063810 1 1, 3
Bleed Valve -- Lower
23075810 1 Valve Assy, Air Bleed -- 6809125 2 1, 2
Compressor Acceleration
-- -- Spacer Assy, Collector 23056721 2 2
Compressor Air Bleed
#*23074928 1 Gasket -- Corrugated, 3 -- -- 1
bolts
#*23074440 1 Cover, Acceleration Bleed -- -- 1
Port -- Upper
--ATTACHING PARTS--
#*MS9557--10 3 Bolt, Mach 12 PT, MS9697--33 3 1, 3
0.250--28 X 0.750 LG
-- -- Nut, Self--locking 12 PT, AS3477--10 REF --
0.250--28 1200Deg F
------*------
#*AS3217--163 1 Ring, Retaining, Spiral, AS3217--163 1 1, 3
Internal, 2.748 OD X
0.049 THK
#*23062486--32 2 Retainer, PSI Tube Seal 23062486--32 2 1, 3
*23074438 1 Tube Assy, Air Bleed 23061724 1 1, 3
Control 23056817 1
-- -- Tube Assy, Air -- Start 23070419 1 3
Bleed Control Valve to 23063899 1
Line Tee 23055512 1

December 21, 2006 AE 3007C--75--034

Page 14 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN
QTY/ QTY/ INSTRUCTIONS/
NEW P/N ENG NAME OLD P/N ENG DISPOSITION
-- -- Tube Assy, Line Tee to 23076605 1 3
Service Manifold 23060972 1
23056818 1
-- -- Tube Assy, Air -- Diffuser 23070418 1 3
to Start Bleed Control 23035948 1
Valve
-- -- Valve Assy, Check 23066190 1 3
#MS8005E214AC 1 Hose Assy, TFE 23061724 1 1, 3
#6886430E214AC ALT 23056817 1
-- -- Elbow, Check Valve to 23076608 1 3
Transfer Tube -- Air Bleed
Control
-- -- Tube Assy, Bleed Control 23076606 1 3
Transfer
-- -- Bracket Assy, Support 23076607 1 3
Elbow Air Bleed Control
#23037873--32 1 Clamp, Single Loop -- -- 1
Cushion, 2.00 ID
#23060015--06 1 Clamp, Single Loop, 0.375 -- -- 1
ID
--ATTACHING PARTS--
#MS9696--06 1 Bolt, Mach, 12 PT, -- -- 1
0.190--32 X 0.500 LG
#AS3477--09 1 Nut, Self Locking, 12 PT, -- -- 1
0.190--32
------*------
#*AN929--4J 1 Cap Assy, Steel -- -- -- 1
Pressure Seal 0.4375--20
MS9142--041 1 Gasket, Metal O--ring MS9142--041 1 3
1.375 OD X 0.063 THK
23038910 1 Cover, Customer Bleed 23052650 1 1, 3
Port, Compressor

INSTRUCTIONS/DISPOSITION NOTES
1. New item.
2. Return removed item.
3. Discard item.
4. Rework item to new configuration.
5. Change quantity.

December 21, 2006 AE 3007C--75--034

Page 15 of 16
EXPORT CONTROLLED Rolls--Royce
SERVICE BULLETIN
B. Consumable Materials
(1) Compound, antiseize, NSN--165.
C. Expendable Parts -- None

CUSTOMER SUPPORT
ROLLS-ROYCE

December 21, 2006 AE 3007C--75--034

Page 16 of 16
PARTS RETURN REPORT
Rolls-Royce Corporation
1--888--255--4766 or 317--230--6400
Date _____________________

PART AND SHIPPING DETAILS: (Required) PART HISTORY: (Recommended)


Part Number ______________________________________ Total part time _________________________________
Part quantity ______________________________________ Total part cycles ________________________________
Part Name ________________________________________ Part time since O/H or repair ______________________
Part Serial Number _________________________________ Part cycles since O/H or repair ____________________
Operator _________________________________________ Engine Model __________________________________
Part shipped from: _____________________________ Engine Serial Number ___________________________
(address) _____________________________ Total engine time _______________________________
_____________________________ Total engine cycles _____________________________
Customer contact _____________________________ Aircraft reg # __________________________________
Phone/FAX/email _____________________________ Engine position (L/H or R/H) ______________________
Shipped via: _____________________________ Field Service Report Number _____________________
AWB _____________________________

REASON FOR RETURN/ACTION REQUIRED: (Required)


__________________________________________________________________________________________________
__________________________________________________________________________________________________
FIM task ___________________________________________________________
CMC Message ___________________________________________________________
Description of failure mode ___________________________________________________________
Service bulletin compliance ___________________________________________________________
Other (details required) ___________________________________________________________

ORDER DETAILS:
Repair order/purchase order/EAFA tracking number ______________________________________________
Date of issue for the repair order/purchase order/EAFA ______________________________________________

CONTACT INFO: (Required for investigation hardware)


Rolls--Royce person requesting return (and phone #): _______________________________________________________

Was a local investigation performed? Yes No If Yes, please attach report.


For additional information contact: (sender) ________________________________ Phone: _________________________

SHIPPING INSTRUCTIONS: (Include a copy of this report with shipment)

(Check the appropriate engine program box)


AE Commercial Engines AE Military Engines AE 1107C Engines
(AE 2100A, AE 2100C, (AE 2100D2, AE 2100D3,
AE 3007A Series, and AE 3007C) and AE 2100J)

Include a copy of this report with the shipment, and ship the part(s) to:

For New/Unused Parts Returns: For Normal/Investigation Parts Returns:


Rolls-Royce Corporation Rolls-Royce Corporation
New/Unused Parts Returns C/O UPS -- SCS
Plant 5 - Stop 313 Returns Processing Center
2355 South Tibbs Avenue 2840 Fortune Circle West Drive
Indianapolis, Indiana 46241 Dock Door 16
USA Indianapolis, Indiana 46241
USA

GT--1133 (02/03)

You might also like