Professional Documents
Culture Documents
ANSI
3121138
August 13, 2008
FOREWORD
FOREWORD
This manual is a very important tool! Keep it with the machine at all times.
The purpose of this manual is to provide owners, users, operators, lessors, and lessees with the precautions and
operating procedures essential for the safe and proper machine operation for its intended purpose.
Due to continuous product improvements, JLG Industries, Inc. reserves the right to make specification changes
without prior notification. Contact JLG Industries, Inc. for updated information.
This is the Safety Alert Symbol. It is used to alert you to the potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid possible
injury or death
INDICATES AN IMMINENTLY HAZARDOUS SITUATION. IF NOT INDI CAT ES A POTE NTIA LLY HAZ AR DOUS SIT UATI ON. IF NOT
AVOIDED, WILL RESULT IN SERIOUS INJURY OR DEATH. THIS DECAL AVOIDED, COULD RESULT IN SERIOUS INJURY OR DEATH. THIS
WILL HAVE A RED BACKGROUND. DECAL WILL HAVE AN ORANGE BACKGROUND.
INDI CAT ES A POTE NTIA LLY HAZ AR DOUS SIT UATI ON. IF NOT
AVOIDED, MAY RESULT IN MINOR OR MODERATE INJURY. IT MAY
ALSO ALERT AGAINST UNSAFE PRACTICES. THIS DECAL WILL HAVE A
YELLOW BACKGROUND.
For:
THIS PRODUCT MUST COMPLY WITH ALL SAFETY RELATED BULLE- Accident Reporting Standards and Regulations
TINS. CONTACT JLG INDUSTRIES, INC. OR THE LOCAL AUTHORIZED Compliance Information
Product Safety Publica-
JLG REPRESENTATIVE FOR INFORMATION REGARDING SAFETY-
tions Questions Regarding Spe-
RELATED BULLETINS WHICH MAY HAVE BEEN ISSUED FOR THIS cial Product Applications
PRODUCT. Current Owner Updates
Questions Regarding Prod-
Questions Regarding
uct Modifications
Product Safety
JLG INDUSTRIES, INC. SENDS SAFETY RELATED BULLETINS TO THE
OWNER OF RECORD OF THIS MACHINE. CONTACT JLG INDUSTRIES,
Contact:
INC. TO ENSURE THAT THE CURRENT OWNER RECORDS ARE Product Safety and Reliability Department
UPDATED AND ACCURATE. JLG Industries, Inc.
13224 Fountainhead Plaza
Hagerstown, MD 21742
JLG INDUSTRIES, INC. MUST BE NOTIFIED IMMEDIATELY IN ALL or Your Local JLG Office
INSTANCES WHERE JLG PRODUCTS HAVE BEEN INVOLVED IN AN (See addresses on inside of manual cover)
ACCIDENT INVOLVING BODILY INJURY OR DEATH OF PERSONNEL OR
WHEN SUBSTANTIAL DAMAGE HAS OCCURRED TO PERSONAL PROP- In USA:
ERTY OR THE JLG PRODUCT.
Toll Free: 877-JLG-SAFE (877-554-7233)
Outside USA:
Phone: 240-420-2661
Fax: 301-745-3713
E-mail: ProductSafety@JLG.com
REVISION LOG
Read, understand, and obey all DANGERS, WARNINGS, This machine can be operated in temperatures of 0o F to
CAUTIONS, and operating instructions on the machine
104o F (-20o C to 40o C). Consult JLG for operation out-
and in this manual.
side this range.
Use the machine in a manner which is within the scope of
its intended application set by JLG. Machine Inspection
All operating personnel must be familiar with the emer- Before machine operation, perform inspections and func-
gency controls and emergency operation of the machine tional checks. Refer to Section 2 of this manual for
as specified in this manual. detailed instructions.
Read, understand, and obey all applicable employer, Do not operate this machine until it has been serviced and
local, and governmental regulations as they pertain to maintained according to requirements specified in the
operation of the machine. Service and Maintenance Manual.
Workplace Inspection Be sure the footswitch and all other safety devices are
operating properly. Modification of these devices is a
The operator is to take safety measures to avoid all haz- safety violation.
ards in the work area prior to machine operation.
Do not operate or raise the platform while on trucks, trail-
ers, railway cars, floating vessels, scaffolds or other equip- MODIFICATION OR ALTERATION OF AN AERIAL WORK PLATFORM
ment unless approved in writing by JLG. SHALL BE MADE ONLY WITH WRITTEN PERMISSION FROM THE MANU-
Do not operate the machine in hazardous environments FACTURER
unless approved for that purpose by JLG.
Do not operate any machine on which safety or instruction
Be sure that the ground conditions are able to support the placards or decals are missing or illegible.
maximum load shown on the decals located on the
machine. Avoid any buildup of debris on the platform floor. Keep
mud, oil, grease, and other slippery substances from foot-
wear and platform floor.
1.3 OPERATION Supplies or tools which extend outside the platform are
prohibited unless approved by JLG.
General When driving, always position boom over rear axle in line
with the direction of travel. Remember, if boom is over the
Do not use the machine for any purpose other than posi- front axle, steer and drive functions will be reversed.
tioning personnel, their tools, and equipment.
Do not assist a stuck or disabled machine by pushing,
Never operate a machine that is not working properly. If a pulling, or by using boom functions. Only pull the unit
malfunctions occurs, shut down the machine. from the tie-down lugs on the chassis.
Never slam a control switch or lever through neutral to an Do not place boom or platform against any structure to
opposite direction. Always return switch to neutral and steady the platform or to support the structure.
stop before moving the switch to the next function. Oper-
ate controls with slow and even pressure. Stow boom and shut off all power before leaving machine.
Hydraulic cylinders should never be left fully extended or Trip and Fall Hazards
fully retracted before shutdown or for long periods of time.
During operation, occupants in the platform must wear a full
Do not allow personnel to tamper with or operate the
body harness with a lanyard attached to an authorized lan-
machine from the ground with personnel in the platform,
yard anchorage point. Attach only one (1) lanyard per lan-
except in an emergency.
yard anchorage point.
Do not carry materials directly on platform railing unless
approved by JLG.
When two or more persons are in the platform, the opera-
tor shall be responsible for all machine operations.
Always ensure that power tools are properly stowed and
never left hanging by their cord from the platform work
area.
Before operating the machine, make sure all gates are Use extreme caution when entering or leaving platform.
closed and fastened in their proper position. Be sure that the boom is fully lowered. It may be neces-
sary to telescope out to position the platform closer to the
ground for entry/exit. Face the machine, maintain three
point contact with the machine, using two hands and one
foot or two feet and one hand during entry and exit.
Electrocution Hazards
This machine is not insulated and does not provide pro-
tection from contact or proximity to electrical current.
Do not elevate platform or drive with platform elevated If boom assembly or platform is in a position that one or
while on a sloping, uneven, or soft surface. more wheels are off the ground, all persons must be
removed before attempting to stabilize the machine. Use
Before driving on floors, bridges, trucks, and other sur-
cranes, forklift trucks, or other appropriate equipment to
faces, check allowable capacity of the surfaces.
stabilize machine and remove personnel.
Never exceed the maximum platform capacity. Distribute
loads evenly on platform floor. Crushing and Collision Hazards
Do not raise the platform or drive from an elevated posi- Approved head gear must be worn by all operating and
tion unless the machine is on firm, level and smooth sur- ground personnel.
faces.
Check work area for clearances overhead, on sides, and
Keep the chassis of the machine at least 2 ft. (0.6m) from bottom of platform when lifting or lowering platform, and
holes, bumps, drop-offs, obstructions, debris, concealed driving.
holes, and other potential hazards on the floor/surface.
Do not push or pull any object with the boom.
Never attempt to use the machine as a crane. Do not tie-
off machine to any adjacent structure.
Do not operate the machine when wind conditions exceed
28 mph (12.5 m/s).
Do not increase the surface area of the platform or the
load. Increase of the area exposed to the wind will
decrease stability.
Do not increase the platform size with unauthorized deck
extensions or attachments.
During operation, keep all body parts inside platform rail-
ing.
Use the boom functions, not the drive function, to position 1.4 TOWING, LIFTING, AND HAULING
the platform close to obstacles.
Never allow personnel in platform while towing, lifting, or
Always post a lookout when driving in areas where vision
hauling.
is obstructed.
This machine should not be towed, except in the event of
Keep non-operating personnel at least 6 ft. (1.8m) away
emergency, malfunction, power failure, or loading/unload-
from machine during all driving and swing operations.
ing. Refer to the Emergency Procedures section of this
Limit travel speed according to conditions of ground sur- manual for emergency towing procedures.
face, congestion, visibility, slope, location of personnel,
Ensure boom is in the stowed position and the turntable
and other factors which may cause collision or injury to
locked prior to towing, lifting or hauling. The platform must
personnel.
be completely empty of tools.
Be aware of stopping distances in all drive speeds. When
When lifting machine, lift only at designated areas of the
driving in high speed, switch to low speed before stop-
machine. Lift the unit with equipment of adequate capac-
ping. Travel grades in low speed only.
ity.
Do not use high speed drive in restricted or close quarters
Refer to the Machine Operation section of this manual for
or when driving in reverse.
lifting information.
Exercise extreme caution at all times to prevent obstacles
from striking or interfering with operating controls and per-
sons in the platform.
Be sure that operators of other overhead and floor level
machines are aware of the aerial work platforms pres-
ence. Disconnect power to overhead cranes.
Warn personnel not to work, stand, or walk under a raised
boom or platform. Position barricades on floor if neces-
sary.
NOTES:
Primary Service
Type Frequency Reference
Responsibility Qualification
Pre-Start Inspection Before using each day; or User or Operator User or Operator Operator and Safety Manual
whenever theres an Operator change.
Pre-Delivery Inspection (See Before each sale, lease, or rental delivery. Owner, Dealer, or User Qualified JLG Service and Maintenance
Note) Mechanic Manual and applicable JLG
inspection form
Frequent Inspection In service for 3 months or 150 hours, whichever Owner, Dealer, or User Qualified JLG Service and Maintenance
(See Note) comes first; Mechanic Manual and applicable JLG
or inspection form
Out of service for a period of more than 3 months;
or
Purchased used.
Annual Machine Inspection Annually, no later than 13 months from the date of Owner, Dealer, or User Factory Certified Service and Maintenance
(See Note) prior inspection. Service Technician Manual and applicable JLG
(Recommended) inspection form
Preventative Maintenance At intervals as specified in the Service and Main- Owner, Dealer, or User Qualified JLG Service and Maintenance
tenance Manual. Mechanic Manual
NOTE: Inspection forms are available from JLG. Use the Service and Maintenance Manual to perform inspections.
Perform the Function Check as follows: a. Drive the machine on a grade, not to exceed the
rated gradeability, and stop to ensure the brakes
1. From the ground control panel with no load in the plat- hold;
form: b. Check the tilt sensor alarm to ensure proper opera-
a. Check that all guards protecting the switches or tion.
locks are in place;
b. Operate all functions and check all limiting and cut-
out switches;
c. Check auxiliary power (or manual descent);
d. Ensure that all machine functions are disabled
when the Emergency Stop Button is activated.
2. From the platform control console:
a. Ensure that the control console is firmly secured in
the proper location;
b. Check that all guards protecting the switches or
locks are in place;
c. Operate all functions and check all limiting and cut-
out switches;
d. Ensure that all machine functions are disabled
when the Emergency Stop Button is pushed in.
1. Steer Wheels
2. Drive Wheels
3. Lift Cylinder
4. Tower
5. Level Link
6. Upright
7. Base Boom Section
8. Mid Boom Section
9. Fly Boom Section
10. Boom Assembly
11. Power Track
12. Jib (If Equipped)
13. Platform
14. Platform Console
TO AVOID POSSIBLE INJURY, BE SURE MACHINE POWER IS OFF. 7. Hood Assemblies - See Inspection Note.
8. Auxiliary Hydraulic Pump - See Inspection Note.
DO NOT OPERATE MACHINE UNTIL ALL MALFUNCTIONS HAVE BEEN COR-
RECTED. 9. All Hydraulic Cylinders - No visible damage; pivot pins
and hydraulic hoses undamaged, not leaking.
INSPECTION NOTE: On all components, make sure there are
no loose or missing parts, that they are securely fastened, and 10. Turntable Bearing - Evidence of proper lubrication. No
no visible damage, leaks or excessive wear exists in addition to evidence of loose bolts or looseness between bearing
any other criteria mentioned. and machine.
1. Platform Assembly and Gate - Footswitch works prop- 11. Tie Rod Ends and Steering Spindles - See Inspection
erly, not modified, disabled or blocked. Latch, stop, and Note.
hinges in working condition. 12. Horizontal and Capacity Limit Switches - Switches
2. Platform & Ground Control Consoles - Switches and operate properly.
levers return to neutral, decals/placards secure and legi- 13. Main Hydraulic Pump - See Inspection Note.
ble, control markings legible.
14. Platform Rotator - See Inspection Note.
3. Boom Sections/Uprights/Turntable - See Inspection
Note.
Figure 2-3. Daily Walk-Around Inspection - Sheet 2 of 2
2.4 OSCILLATING AXLE LOCKOUT TEST (IF 3. Place the Drive control lever to the forward position and
carefully drive machine up ascension ramp until left front
EQUIPPED) wheel is on top of block.
4. Carefully activate Swing control lever and position boom
over right side of machine.
LOCKOUT SYSTEM TEST MUST BE PERFORMED QUARTERLY, ANY TIME
A SYSTEM COMPONENT IS REPLACED, OR WHEN IMPROPER SYSTEM 5. With boom over right side of machine, place Drive con-
OPERATION IS SUSPECTED. trol lever to Reverse and drive machine off of block and
ramp.
NOTE: Ensure boom is fully retracted, lowered, and centered 6. Have an assistant check to see that left front or right rear
between drive wheels prior to beginning lockout cylinder wheel remains elevated in position off of ground.
test.
7. Carefully activate Swing control lever and return boom
1. Place a 6 inches (15.2 cm) high block with ascension to stowed position (centered between drive wheels).
ramp in front of left front wheel. When boom reaches center, stowed position, lockout
cylinders should release and allow wheel to rest on
2. From platform control station, start engine ground, it may be necessary to activate Drive to release
cylinders.
8. Place the 6 inches (15.2 cm) high block with ascension 12. Carefully activate Swing control lever and return boom
ramp in front of right front wheel. to stowed position (centered between drive wheels).
When boom reaches center, stowed position, lockout
9. Place Drive control lever to Forward and carefully drive
cylinders should release and allow wheel to rest on
machine up ascension ramp until right front wheel is on
ground, it may be necessary activate Drive to release
top of block.
cylinders.
10. With boom over left side of machine, place Drive control
13. If lockout cylinders do not function properly, have quali-
lever to Reverse and drive machine off of block and
fied personnel correct the malfunction prior to any fur-
ramp.
ther operation.
11. Have an assistant check to see that right front or left rear
wheel remains elevated in position off of ground.
NOTES:
3.2 CONTROLS AND INDICATORS WHEN THE MACHINE IS SHUT DOWN THE MASTER/EMERGENCY STOP
SWITCH MUST BE POSITIONED TO THE OFF POSITION TO PREVENT
NOTE: This machines is equipped with control panels that use DRAINING THE BATTERY.
symbols to indicate control functions. Refer to decal
located on the control box guard in front of the control NOTE: If equipped, the Function Enable switch must
box or by the ground controls for these symbols and the be held down in order to operate Telescope,
corresponding functions. Swing, Lift, Jib Lift, Platform Level Override,
and Platform Rotate functions.
The LED Indicator Panel contains indicator lights that A three position, key operated switch supplies power to
signal problem conditions or functions operating during the platform control console when positioned to PLAT-
machine operation. FORM. With the switch key held in the GROUND posi-
tion, power is shut off to platform and only ground
controls are operable.
TO AVOID SERIOUS INJURY, DO NOT OPERATE MACHINE IF ANY CON- NOTE: With PLATFORM/GROUND SELECT switch in the center
TROL LEVERS OR TOGGLE SWITCHES CONTROLLING PLATFORM position, power is shut off to controls at both operating
MOVEMENT DO NOT RETURN TO THE OFF POSITION WHEN RELEASED. stations.
Provides extension and retraction of the boom, when Registers the amount of time the machine has been in
positioned to IN or OUT. use, with engine running. By connecting into the oil
pressure circuit of the engine, only engine run hours are
3. Swing Control.
recorded. The hourmeter registers up to 9,999.9 hours
and cannot be reset.
Provides 360 degrees continuous turntable rotation.
7. Power/Emergency Stop Switch.
4. Lift Control.
A two-position red mushroom shaped switch furnishes
Provides raising and lowering of the main boom.
power to PLATFORM/GROUND SELECT switch when
pulled out (on). When pushed in (off), power is shut off
to the PLATFORM/GROUND SELECT switch.
1. Indicator Panel
2. Telescope
3. Swing
4. Lift
5. Platform/Ground Select Switch
6. Hourmeter
7. Power/Emergency Stop
8. Engine Start/Auxiliary Power
or
Engine Start/Auxiliary Power/Function Enable
9. N/A
10. Platform Leveling Override
11. Platform Rotate
1. Indicator Panel
2. Telescope
3. Swing
4. Lift
5. Platform/Ground Select Switch
6. Hourmeter
7. Power/Emergency Stop
8. Engine Start/Auxiliary Power
or
Engine Start/Auxiliary Power/Function Enable
9. Articulating Jib Boom
10. Platform Leveling Override
11. Platform Rotate
(See Figure 3-2., Ground Control Indicator Panel) Indicates a problem in the battery or charging circuit,
and service is required.
2. Low Engine Oil Pressure Indicator.
NOTE: MAIN LIFT, SWING, and DRIVE control levers are spring- 5. Drive/Steer
loaded and will automatically return to neutral (OFF) posi-
tion when released. The DRIVE joystick provides for driving either forward or
backward. The controller is ramped to allow variable
drive speed.
TO AVOID SERIOUS INJURY, DO NOT OPERATE MACHINE IF ANY CON- Steering is controlled by a thumb operated switch on
TROL LEVERS OR TOGGLE SWITCHES CONTROLLING PLATFORM top of the joystick.
MOVEMENT DO NOT RETURN TO THE OFF OR NEUTRAL POSITION
WHEN RELEASED. NOTE: To operate the Drive Joystick, pull up on the locking ring
below the handle.
3. Main Lift/Swing Controller.
NOTE: When boom is positioned above horizontal and any of the
An infinitely proportional dual axis joystick is provided following switches, DRIVE SPEED/TORQUE SELECT or
FUNCTION SPEED, are positioned to HIGH, high function
for main lift and swing. Push forward to lift up, pull back-
ward to lift down. Move right to swing right, move left to speeds are automatically cut out and the machine contin-
swing left. ues to operate at a lower speed.
Controls the speed of Boom and Swing Functions. Push forward to lift up, pull back to lift down. Variable lift
Rotate CCW for slower speed and CW for faster speed. speed is using the Function Speed Control.
To adjust to creep, turn knob fully CCW until it clicks.
11. Fuel Select (Dual Fuel Engine Only). (If Equipped)
7. Drive Speed/Torque Select.
Gasoline or liquid propane fuel may be selected by mov-
The forward position gives maximum drive speed by ing the switch to the appropriate position. It is unneces-
shifting the drive motors to minimum the displacement sary to purge the fuel system before switching fuels, so
and giving high engine when drive controller is moved. there is no waiting period when switching fuels while the
The back position gives maximum torque for rough ter- engine is running.
rain and climbing grades by shifting the wheel motors to
12. Lights. (If Equipped)
maximum displacement and giving high engine speed
when drive controller is moved. The center position
This switch operates control console panel lights and
allows the machine to be driven as quietly as possible
head lights if the machine is so equipped. The ignition
by leaving the engine at mid speed and the drive motors
switch does not have to be on to operate the lights, so
in maximum displacement.
care must be taken to avoid draining the battery if left
8. Platform Rotate. unattended. The master switch and / or the ignition
switch at the ground control will turn off power to all
This switch allows the operator to rotate the basket to lights.
the left or right.
9. Platform Leveling Override.
When equipped with four wheel steering, the action of When pushed forward, the switch energizes the starter
the steering system is operator selectable. The center motor to start the engine.
switch position gives conventional front wheel steering
with the rear wheels unaffected. This is for normal driv- When pushed back, it energizes the electrically oper-
ing at maximum speeds. The forward position is for ated hydraulic pump, when actuated. (Switch must be
crab steering. When in this mode both front and rear held ON for duration of auxiliary pump use.)
axles steer in the same direction, which allows the chas-
sis to move sideways as it goes forward. This can be The auxiliary pump functions to provide sufficient oil flow
used for positioning the machine in aisle ways or against to operate the basic machine functions should the main
buildings. The back switch position is for coordinated pump or engine fail. The auxiliary pump will operate
steering. In this mode the front and rear axles steer in tower boom lift, tower telescope, main boom lift, main
the opposite directions to produce the tightest turning telescope and swing.
circle for maneuvering in confined areas. 15. Indicator Panel.
To re-synchronize the front and rear axles, position the The LED Indicator Panel contains indicator lights that
rear drive wheels to the forward drive position by select- signal problem conditions or functions operating during
ing either crab or compound steer, then select front machine operation.
steer (center switch position) to operate the normal
steering function.
(See Figure 3-4., Platform Light Panel) Indicates a fault in the electronic leveling system. The
fault indicator will flash and an alarm sound. All func-
NOTE: The platform control indicator panel uses different shaped tions will default to creep if the boom is extended more
symbols to alert the operator to different types of opera- than 20 inches (51 cm) or elevated above horizontal.
tional situations that could arise. The meaning of those
symbols are explained below.
Indicates a potentially hazardous situation, which
IF THE LEVEL SYSTEM FAULT INDICATOR IS ILLUMINATED, SHUT
if not corrected, could result in serious injury or
death. This indicator will be red. DOWN THE MACHINE, RECYCLE THE EMERGENCY STOP, AND RESTART
THE MACHINE. IF THE FAULT PERSISTS, RETURN THE PLATFORM TO
THE STOWED POSITION, USING MANUAL LEVELING AS REQUIRED,
Indicates an abnormal operating condition,
AND HAVE LEVELING SYSTEM REPAIRED.
which if not corrected, may result in machine
interruption or damage. This indicator will be yel-
low. 2. AC Generator. (Green)
Indicates the maximum platform capacity for the current Indicates the glow plugs are operating. After turning on
position of the platform. Restricted capacities are permit- ignition, wait until light goes out before cranking engine.
ted at restricted platform positions (shorter boom
7. Footswitch/Enable Indicator
lengths and higher boom angles).
NOTE: Refer to the capacity decals on the machine for restricted To operate any function, the footswitch must be
and unrestricted platform capacities. depressed and the function selected within seven sec-
onds. The enable indicator shows that the controls are
5. Tilt Alarm Warning Light and Alarm enabled. If a function is not selected within seven sec-
onds, or if a seven second lapse between ending one
This orange illuminator indicates that the chassis is on a function and beginning the next function, the enable
slope. An alarm will also sound when the chassis is on a light will go out and the footswitch must be released and
slope and the boom is above horizontal. If lit when boom depressed again to enable the controls.
is raised or extended, retract and lower to below hori-
zontal then reposition machine so that it is level before Releasing the footswitch removes power from all con-
continuing operation. If the boom is above horizontal trols and applies the drive brakes.
and the machine is on a slope, the tilt alarm warning
light will illuminate and an alarm will sound and CREEP
is automatically activated.
TO AVOID SERIOUS INJURY, DO NOT REMOVE, MODIFY OR DISABLE
THE FOOTSWITCH BY BLOCKING OR ANY OTHER MEANS.
Indicates the level of fuel in the fuel tank. When illuminated, the light indicates the boom cables
are loose or broken and must be repaired or adjusted
9. Creep Speed Indicator.
immediately.
When the Function Speed Control is turned to the creep
position, the indicator acts as a reminder that all func-
tions are set to the slowest speed. IF THE CABLE SERVICE INDICATOR IS ILLUMINATED, RETURN THE
PLATFORM TO THE STOWED POSITION, SHUT DOWN THE MACHINE,
10. Engine Malfunction Indicator.
AND HAVE THE BOOM CABLES INSPECTED.
The light indicates that the JLG Control System has
12. Soft Touch Indicator. (If Equipped)
detected a malfunction and a Diagnostic Trouble Code
has been set in the system memory. Refer to the Service
Indicates the Soft Touch bumper is against an object. All
Manual for instructions concerning the trouble codes
controls are cut out until the override button is pushed,
and trouble code retrieval.
at which time controls are active in the Creep mode.
The malfunction indicator light will illuminate for 2-3 sec-
onds when the key is positioned to the on position to act
as a self test.
NOTES:
TO AVOID FORWARD OR BACKWARD TIPPING, DO NOT OVERLOAD ALLOW ENGINE TO WARM-UP FOR A FEW MINUTES AT LOW SPEED
MACHINE OR OPERATE THE MACHINE ON AN OUT-OF-LEVEL SURFACE. BEFORE APPLYING ANY LOAD.
4.3 ENGINE OPERATION 2. After engine has had sufficient time to warm up, shut
engine off.
NOTE: Initial starting should always be performed from the
3. Turn SELECT switch to PLATFORM.
Ground Control station.
4. From Platform, pull POWER/EMERGENCY STOP switch
Starting Procedure out, then push the ENGINE START switch until engine
starts.
Shutdown Procedure .
TURNTABLE ROTATED
90 DEGREES FROM
STOWED POSITION
TELESCOPE
FULLY EXTENDED
TO AVOID LOSS OF TRAVEL CONTROL OR TIP OVER , DO NOT DRIVE Traveling Forward and Reverse
MACHINE ON GRADES EXCEEDING THOSE SPECIFIED ON THE SERIAL
NUMBER PLATE.
1. At Platform Controls, pull out Emergency Stop switch,
start engine, and activate footswitch.
DO NOT DRIVE ON SIDESLOPES WHICH EXCEED 5 DEGREES.
2. Position Drive controller to FORWARD or REVERSE as
USE EXTREME CAUTION WHEN DRIVING IN REVERSE AND AT ALL desired.
TIMES WHEN THE PLATFORM IS ELEVATED.
4.5 STEERING
BEFORE DRIVING, LOCATE THE BLACK/WHITE ORIENTATION ARROWS
ON BOTH THE CHASSIS AND THE PLATFORM CONTROLS. MOVE THE Position thumb switch on Drive/Steer controller to RIGHT for
steering right, or to LEFT for steering left.
To rotate the platform to the left or right, use the Platform TO AVOID SERIOUS INJURY, DO NOT OPERATE MACHINE IF ANY CON-
Rotate control switch to select the direction and hold until TROL LEVER OR TOGGLE SWITCH CONTROLLING PLATFORM MOVE-
desired position is reached. MENT DOES NOT RETURN TO THE OFF OR NEUTRAL POSITION WHEN
RELEASED.
4.12 SHUT DOWN AND PARK 4.13 LIFTING AND TIE DOWN
To shut down and park the machine, the procedures are as
follows:
Lifting
1. Drive machine to a reasonably well protected area. 1. Call JLG Industries or weigh the individual unit to find
out the Gross Vehicle Weight.
2. Ensure boom is lowered over rear drive axle.
2. Place the boom in the stowed position with the turntable
3. Push in the Emergency Stop at Platform Controls.
locked.
4. Push in the Emergency Stop at Ground Controls. Posi-
3. Remove all loose items from the machine.
tion Platform/Ground Select switch to center OFF.
4. Properly adjust the rigging to prevent damage to the
5. If necessary, cover Platform Controls to protect instruc-
machine and so the machine remains level.
tion placards, warning decals and operating controls
from hostile environment.
Tie Down
DRIVE AND STEER CONTROLLERS WILL BE REVERSED WHEN THE
BOOM IS POSITIONED OVER THE FRONT WHEELS.
WHEN TRANSPORTING THE MACHINE, THE BOOM MUST BE FULLY
c. Drive it onto the trailer with the boom and platform
LOWERED INTO THE BOOM REST.
positioned towards the truck. Refer to Figure 4-5.,
Typical 800S/860SJ Transport.
1. Remove all loose items from the machine.
3. Secure the chassis and the platform using straps or
2. When transporting an 800S/860SJ a step-deck or sin-
chains of adequate strength.
gle-drop trailer is required. To avoid damage to the plat-
form and to obtain proper weight distribution, load the
machine onto the trailer as follows;
a. Position the boom over the front wheels.
China/ French/
Item # ANSI Australian Dutch Finnish French German Italian
English English
800S 0270907-2 0270909-2 0270915-2 0271830-2 0270919-2 0270913-2 0270917-2
0270931-1 0270929-1
860SJ 0270908-2 0270910-2 0270916-2 0271831-1 0270920-2 0270914-2 0270918-2
0270932-1 0270930-1
1 1703797 1703992 1703925 1704809 1705053 1704811 1703924 1704767 1704810
2 1703798 1704819 1703931 1704821 1705055 1704823 1703930 1704820 1704822
3 1703805 -- 1703937 -- -- -- 1703936 -- --
4 1703804 1701518 1703949 1701518 1701518 1701518 1703948 1701518 1701518
5 1705015 -- -- -- -- -- 1705015 -- --
6 1703808 -- -- -- -- -- 1703808 -- --
7 1704906 1704906 1704906 1704906 1704906 1704906 1704906 1704906 1704906
(800S) (800S) (800S) (800S) (800S) (800S) (800S) (800S) (800S)
1704907 1704907 1704907 1704907 1704907 1704907 1704907 1704907 1704907
(860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ)
8 -- -- -- -- -- -- -- -- --
9 -- -- -- -- -- -- -- -- --
10 -- -- -- -- -- -- -- -- --
11 1702868 -- -- -- -- -- 1704000 -- --
12 1704277 1704277 1704277 1704277 1704277 1704277 1704277 1704277 1704277
China/ French/
Item # ANSI Australian Dutch Finnish French German Italian
English English
800S 0270907-2 0270909-2 0270915-2 0271830-2 0270919-2 0270913-2 0270917-2
0270931-1 0270929-1
860SJ 0270908-2 0270910-2 0270916-2 0271831-1 0270920-2 0270914-2 0270918-2
0270932-1 0270930-1
13 1705088 1705088 1704101 -- -- -- 1704099 -- --
(800S)
1704995
(860SJ)
14 1705089 1705089 1704109 -- -- -- 1704107 -- --
(800S)
1704996
(860SJ)
15 3251813 -- -- 1705084 1705084 1705084 3251813 1705084 1705084
16 1701502 1701502 1701502 1701502 1701502 1701502 1701502 1701502 1701502
17 1701503 1701503 1701503 1701503 1701503 1701503 1701503 1701503 1701503
18 1701504 1701504 1701504 1701504 1701504 1701504 1701504 1701504 1701504
19 1702153 -- -- -- -- -- 1704006 -- --
20 1702631 1702631 1702631 1702631 1702631 1702631 1702631 1702631 1702631
21 1700584 1700584 1700584 1700584 1700584 1700584 1700584 1700584 1700584
22 -- -- -- -- -- -- -- -- --
23 1701509 1701509 1701509 1701509 1701509 1701509 1701509 1701509 1701509
24 1702300 1702300 1702300 1702300 1702300 1702300 1702300 1702300 1702300
China/ French/
Item # ANSI Australian Dutch Finnish French German Italian
English English
800S 0270907-2 0270909-2 0270915-2 0271830-2 0270919-2 0270913-2 0270917-2
0270931-1 0270929-1
860SJ 0270908-2 0270910-2 0270916-2 0271831-1 0270920-2 0270914-2 0270918-2
0270932-1 0270930-1
25 1701500 1701500 1701500 1701500 1701500 1701500 1701500 1701500 1701500
26 1701501 1701501 1701501 1701501 1701501 1701501 1701501 1701501 1701501
27 -- -- -- -- -- -- -- -- --
28 -- -- -- -- -- -- -- -- --
29 -- -- -- -- -- -- -- -- --
30 -- -- -- -- -- -- -- -- --
31 -- -- -- -- -- -- -- -- --
32 -- -- -- -- -- -- -- -- --
33 -- -- -- -- -- -- -- -- --
34 -- -- 1703982 1703518 1701600 1693292 1703984 1693294 1701600
35 1703475 1703475 1703475 1703475 1703475 1703475 1703475 1703475 1703475
(800S) (800S) (800S) (800S) (800S) (800S) (800S) (800S) (800S)
1703482 1703482 1703482 1703482 1703482 1703482 1703482 1703482 1703482
(860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ)
36 -- -- -- -- -- -- -- -- --
37 -- -- -- -- -- -- -- -- --
38 -- -- -- -- -- -- -- -- --
39 -- -- -- -- -- -- 3252221 -- --
China/ French/
Item # ANSI Australian Dutch Finnish French German Italian
English English
800S 0270907-2 0270909-2 0270915-2 0271830-2 0270919-2 0270913-2 0270917-2
0270931-1 0270929-1
860SJ 0270908-2 0270910-2 0270916-2 0271831-1 0270920-2 0270914-2 0270918-2
0270932-1 0270930-1
40 -- -- -- -- -- -- -- -- --
41 -- -- -- -- -- -- -- -- --
42 -- -- -- -- -- -- -- -- --
43 -- -- -- -- -- -- -- -- --
44 1701499 1701499 1701499 1701499 1701499 1701499 1701499 1701499 1701499
45 3252781 3252781 3252781 3252781 3252781 3252781 3252781 3252781 3252781
46 1704412 1704412 1704412 1704412 1704412 1704412 1704412 1704412 1704412
47 1704540 1704540 1704540 1704540 1704540 1704540 1704540 1704540 1704540
48 1701691 1701691 1701691 1701691 1701691 1701691 1701691 1701691 1701691
49 -- -- -- -- -- -- -- -- --
50 -- -- -- -- -- -- -- -- --
51 -- -- -- -- -- -- -- -- --
52 -- -- -- -- -- -- -- -- --
China/ French/
Item # ANSI Australian Dutch Finnish French German Italian
English English
800S 0270907-2 0270909-2 0270915-2 0271830-2 0270919-2 0270913-2 0270917-2
0270931-1 0270929-1
860SJ 0270908-2 0270910-2 0270916-2 0271831-1 0270920-2 0270914-2 0270918-2
0270932-1 0270930-1
1 1703797 1703992 1703925 1704809 1705053 1704811 1703924 1704767 1704810
2 1703798 1704819 1703931 1704821 1705055 1704823 1703930 1704820 1704822
3 1703805 -- 1703937 -- -- -- 1703936 -- --
4 1703804 1701518 1703949 1701518 1701518 1701518 1703948 1701518 1701518
5 1705015 -- -- -- -- -- 1705015 -- --
6 1703808 -- -- -- -- -- 1703808 -- --
7 1704906 1704906 1704906 1704906 1704906 1704906 1704906 1704906 1704906
(800S) (800S) (800S) (800S) (800S) (800S) (800S) (800S) (800S)
1704907 1704907 1704907 1704907 1704907 1704907 1704907 1704907 1704907
(860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ)
8 -- -- -- -- -- -- -- -- --
9 -- -- -- -- -- -- -- -- --
10 -- -- -- -- -- -- -- -- --
11 1702868 -- -- -- -- -- 1704000 -- --
12 1704277 1704277 1704277 1704277 1704277 1704277 1704277 1704277 1704277
China/ French/
Item # ANSI Australian Dutch Finnish French German Italian
English English
800S 0270907-2 0270909-2 0270915-2 0271830-2 0270919-2 0270913-2 0270917-2
0270931-1 0270929-1
860SJ 0270908-2 0270910-2 0270916-2 0271831-1 0270920-2 0270914-2 0270918-2
0270932-1 0270930-1
13 1705088 1705088 1704101 -- -- -- 1704099 -- --
(800S)
1704995
(860SJ)
14 1705089 1705089 1704109 -- -- -- 1704107 -- --
(800S)
1704996
(860SJ)
15 3251813 -- -- 1705084 1705084 1705084 3251813 1705084 1705084
16 1701502 1701502 1701502 1701502 1701502 1701502 1701502 1701502 1701502
17 1701503 1701503 1701503 1701503 1701503 1701503 1701503 1701503 1701503
18 1701504 1701504 1701504 1701504 1701504 1701504 1701504 1701504 1701504
19 1702153 -- -- -- -- -- 1704006 -- --
20 1702631 1702631 1702631 1702631 1702631 1702631 1702631 1702631 1702631
21 1700584 1700584 1700584 1700584 1700584 1700584 1700584 1700584 1700584
22 -- -- -- -- -- -- -- -- --
23 1701509 1701509 1701509 1701509 1701509 1701509 1701509 1701509 1701509
24 1702300 1702300 1702300 1702300 1702300 1702300 1702300 1702300 1702300
China/ French/
Item # ANSI Australian Dutch Finnish French German Italian
English English
800S 0270907-2 0270909-2 0270915-2 0271830-2 0270919-2 0270913-2 0270917-2
0270931-1 0270929-1
860SJ 0270908-2 0270910-2 0270916-2 0271831-1 0270920-2 0270914-2 0270918-2
0270932-1 0270930-1
25 1701500 1701500 1701500 1701500 1701500 1701500 1701500 1701500 1701500
26 1701501 1701501 1701501 1701501 1701501 1701501 1701501 1701501 1701501
27 -- -- -- -- -- -- -- -- --
28 -- -- -- -- -- -- -- -- --
29 -- -- -- -- -- -- -- -- --
30 -- -- -- -- -- -- -- -- --
31 -- -- -- -- -- -- -- -- --
32 -- -- -- -- -- -- -- -- --
33 -- -- -- -- -- -- -- -- --
34 -- -- 1703982 1703518 1701600 1693292 1703984 1693294 1701600
35 1703475 1703475 1703475 1703475 1703475 1703475 1703475 1703475 1703475
(800S) (800S) (800S) (800S) (800S) (800S) (800S) (800S) (800S)
1703482 1703482 1703482 1703482 1703482 1703482 1703482 1703482 1703482
(860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ) (860SJ)
36 -- -- -- -- -- -- -- -- --
37 -- -- -- -- -- -- -- -- --
38 -- -- -- -- -- -- -- -- --
39 -- -- -- -- -- -- 3252221 -- --
China/ French/
Item # ANSI Australian Dutch Finnish French German Italian
English English
800S 0270907-2 0270909-2 0270915-2 0271830-2 0270919-2 0270913-2 0270917-2
0270931-1 0270929-1
860SJ 0270908-2 0270910-2 0270916-2 0271831-1 0270920-2 0270914-2 0270918-2
0270932-1 0270930-1
40 -- -- -- -- -- -- -- -- --
41 -- -- -- -- -- -- -- -- --
42 -- -- -- -- -- -- -- -- --
43 -- -- -- -- -- -- -- -- --
44 1701499 1701499 1701499 1701499 1701499 1701499 1701499 1701499 1701499
45 3252781 3252781 3252781 3252781 3252781 3252781 3252781 3252781 3252781
46 1704412 1704412 1704412 1704412 1704412 1704412 1704412 1704412 1704412
47 1704540 1704540 1704540 1704540 1704540 1704540 1704540 1704540 1704540
48 1701691 1701691 1701691 1701691 1701691 1701691 1701691 1701691 1701691
49 -- -- -- -- -- -- -- -- --
50 -- -- -- -- -- -- -- -- --
51 -- -- -- -- -- -- -- -- --
52 -- -- -- -- -- -- -- -- --
To Retract and Lower Boom To Lower Boom with Fully Retracted Telescope
1. Turn knob #1 and #4 clockwise until tight. 1. Turn knob #1 and #3 clockwise until tight.
2. Turn knobs #2 and #3 counterclockwise 3 turns. 2. Turn knob #2 counterclockwise 3 turns.
3. Pump the hand pump until tight. 3. Turn knob #4 counterclockwise until fully open.
4. After telescope has fully retracted turn knob #4 counter- 4. Pump the hand pump until tight.
clockwise until fully open to continue lowering boom.
NOTE: When the manual descent operation has been completed,
knobs #1, #2, and #3 should be open (counterclock-
wise), knob #4 should be closed (clockwise).
NOTES:
Table 6-6. Deutz D2011L04 Specifications Table 6-7. Caterpillar 3044C/ Caterpillar 3.4
Aside from JLG recommendations, it is not advisable to mix oils Table 6-14. Mobil DTE 13M Specs
of different brands or types, as they may not contain the same
required additives or be of comparable viscosities. If use of ISO Viscosity Grade #32
hydraulic oil other than Mobilfluid 424 is desired, contact JLG
Specific Gravity 0.877
Industries for proper recommendations.
Pour Point, Max -40F (-40C)
Table 6-13. Mobilfluid 424 Specs
Flash Point, Min. 330F (166C)
SAE Grade 10W30
Viscosity
Gravity, API 29.0
at 40 C 33cSt
Density, Lb/Gal. 60F 7.35 at 100 C 6.6 cSt
Pour Point, Max -46F (-43C) at 100 F 169 SUS
Flash Point, Min. 442F (228C) at 210 F 48 SUS
Viscosity cp at -20 F 6,200
Brookfield, cP at -18C 2700 Viscosity Index 140
at 40 C 55 cSt
at 100 C 9.3 cSt
Viscosity Index 152
Table 6-15. Mobil EAL 224H Specs Table 6-16. UCon Hydrolube HP-5046
4150548-C
Figure 6-3. Engine Operating Temperature Specifications - Deutz - Sheet 2 of 2
4150548-C
Figure 6-5. Engine Operating Temperature Specifications - Ford - Sheet 2 of 2
4150548-C
Figure 6-7. Engine Operating Temperature Specifications - Caterpillar - Sheet 2 of 2
4150548-C
Figure 6-9. Engine Operating Temperature Specifications - GM - Sheet 2 of 2
6.4 OPERATOR MAINTENANCE NOTE: It is recommended as a good practice to replace all filters
at the same time.
NOTE: The following numbers correspond to those in Figure 6-
10., Operator Maintenance and Lubrication Diagram. 1. Swing Bearing - Internal Ball Bearing
KEY SPECIFICATIONS
MPG Multipurpose Grease having a minimum dripping point of 350 F
(177 C). Excellent water resistance and adhesive qualities, and
being of extreme pressure type.
(Timken OK 40 pounds minimum.)
EPGL Extreme Pressure Gear Lube (oil) meeting API service classifica-
tion GL-5 or MIL-Spec MIL-L-2105
HO Hydraulic Oil. API service classification GL-3, e.g. Mobilfluid 424.
EO Engine (crankcase) Oil. Gas - API SF, SH, SG class, MIL-L-2104.
Diesel - API CC/CD class, MIL-L-2104B/MIL-L-2104C.
Lube Point(s) - 1 Grease Fittings
Capacity - A/R
Lube - MPG
Interval - Every 3 months or 150 hrs of operation
LUBRICATION INTERVALS ARE BASED ON MACHINE OPERATION
Comments - Remote Access
UNDER NORMAL CONDITIONS. FOR MACHINES USED IN MULTI-SHIFT
OPERATIONS AND/OR EXPOSED TO HOSTILE ENVIRONMENTS OR CON-
DITIONS, LUBRICATION FREQUENCIES MUST BE INCREASED ACCORD-
INGLY.
Interval - Change after first 50 hrs. and every 6 months or Interval - Change after first 50 hrs. and every 6 months or
300 hrs. thereafter or as indicated by Condition Indicator. 300 hrs. thereafter or as indicated by Condition Indicator.
10. Oil Change w/Filter - Deutz 11. Oil Change w/Filter - Caterpillar
Lube Point(s) - Fill Cap/Spin-on Element (JLG P/N
7026855)
Capacity - 10.6 Quarts
Lube - EO
Interval - 3 Months or 150 hours of operation
Comments - Check level daily/Change in accordance with
engine manual.
18. Electronic Pressure Regulator (LP only) 19. Fuel Filter (Propane) - GM Engine
Interval - 3 Months or 150 hours of operation Interval - 3 Months or 150 hours of operation
Comments - Drain oil build up. Refer to Section 6.6, Comments - Replace filter. Refer to Section 6.7, Propane
Draining Oil Build Up From The Propane Regulator Fuel Filter Replacement
6.5 TIRES & WHEELS For polyurethane foam filled tires, JLG Industries, Inc. recom-
mends that when any of the following are discovered, measures
must be taken to remove the JLG product from service immedi-
Tire Inflation ately and arrangements must be made for replacement of the
The air pressure for pneumatic tires must be equal to the air tire or tire assembly.
pressure that is stenciled on the side of the JLG product or
rim decal for safe and proper operational characteristics. a smooth, even cut through the cord plies which
exceeds 3 inches (7.5 cm) in total length
Tire Damage any tears or rips (ragged edges) in the cord plies
which exceeds 1 inch (2.5 cm) in any direction
For pneumatic tires, JLG Industries, Inc. recommends that when
any cut, rip, or tear is discovered that exposes sidewall or tread any punctures which exceed 1 inch in diameter
area cords in the tire, measures must be taken to remove the any damage to the bead area cords of the tire
JLG product from service immediately. Arrangements must be
made for replacement of the tire or tire assembly. If a tire is damaged but is within the above noted criteria, the tire
must be inspected on a daily basis to insure the damage has
not propagated beyond the allowable criteria.
Tighten the lug nuts to the proper torque to prevent wheels from
coming loose. Use a torque wrench to tighten the fasteners. If
you do not have a torque wrench, tighten the fasteners with a
lug wrench, then immediately have a service garage or dealer
tighten the lug nuts to the proper torque. Over-tightening will
result in breaking the studs or permanently deforming the
mounting stud holes in the wheels. The proper procedure for
attaching wheels is as follows:
1. Start all nuts by hand to prevent cross threading. DO
NOT use a lubricant on threads or nuts.
3. The tightening of the nuts should be done in stages. Fol- 6.6 DRAINING OIL BUILD UP FROM THE
lowing the recommended sequence, tighten nuts per
wheel torque chart. PROPANE REGULATOR
During the course of normal operation oils may build inside
Table 6-19. Wheel Torque Chart
the primary and secondary chambers of the propane pres-
TORQUE SEQUENCE sure regulator. These oils may be a result of poor fuel quality,
contamination of the fuel supply chain, or regional variation
1st Stage 2nd Stage 3rd Stage
in the make up of the fuel. If the build up of the oil is signifi-
70 ft. lbs. 170 ft. lbs. 300 ft. lbs. cant this can effect the operation of the fuel control system.
(95 Nm) (225 Nm) (405 Nm) Refer to Section 6.4, Operator Maintenance for maintenance
intervals. More frequent draining may be required if the fuel
4. Wheel nuts should be torqued after first 50 hours of supply has been contaminated.
operation and after each wheel removal. Check torque
every 3 months or 150 hours of operation.
FOR BEST RESULTS WARM THE ENGINE TO OPERATING TEMPERA-
TURE BEFORE DRAINING. THIS WILL ALLOW THE OILS TO FLOW
FREELY FROM THE REGULATOR.
4. Push in the Emergency Switch once the engine stops. 6. Remove the retainer clip for the LPG fuel temperature
sensor and remove the sensor from the regulator body.
5. Disconnect the electrical connection to the LPG fuel
temperature sensor in the auxiliary fuel port of the EPR.
NOTE: Have a small container ready to collect oil that will drain
freely from the regulator at this point.
7. Once all of the oil has been drained, reinstall the LPG
fuel temperature sensor and reconnect the electrical
connector.
8. Open the fuel tank manual valve.
9. Start the engine and verify all connections are secure.
10. Dispose of any drained oil per local regulations in a safe
and proper fashion.
BE SURE TO REINSTALL THE FILTER MAGNET INTO THE HOUSING THE PROPANE FUEL SYSTEM OPERATES AT PRESSURES UP TO 312
BEFORE INSTALLING NEW SEAL PSI (21.5 BAR). TO MINIMIZE THE RISK OF FIRE AND PERSONAL
INJURY, RELIEVE THE PROPANE FUEL SYSTEM PRESSURE (WHERE
1. Install the mounting plate to lock off O-ring seal. APPLICABLE) BEFORE SERVICING THE PROPANE FUEL SYSTEM COM-
PONENTS.
2. Install the retaining bolt seal.
3. Install the housing seal. To relieve propane fuel system pressure:
4. Drop the magnet into the bottom of the filter housing. 1. Close the manual shut-off valve on the propane fuel
tank.
5. Install the filter into the housing.
2. Start and run the vehicle until the engine stalls.
6. Install the retaining bolt into the filter housing.
3. Turn the ignition switch OFF.
7. Install the filter up to the bottom of the electric lock off.
8. Tighten the filter retaining bolt to 106 in lbs (12 Nm).
9. Open manual shut-off valve. Start the vehicle and leak RESIDUAL VAPOR PRESSURE WILL BE PRESENT IN THE FUEL SYS-
check the propane fuel system at each serviced fitting. TEM. ENSURE THE WORK AREA IS WELL VENTILATED BEFORE DIS-
Refer to Propane Fuel System Leak Test. CONNECTING ANY FUEL LINE.
Date Comments
Date Comments
JLG Europe B.V. JLG Latino Americana Ltda. JLG Polska JLG Industries (Sweden)
Jupiterstraat 234 Rua Eng. Carlos Stevenson, UI. Krolewska Enkopingsvagen 150
2132 HJ Foofddorp 80-Suite 71 00-060 Warsawa Box 704
The Netherlands 13092-310 Campinas-SP Poland SE - 175 27 Jarfalla
Phone: (31) 23 565 5665 Brazil Phone: (48) 91 4320 245 Sweden
Fax: (31) 23 557 2493 Phone: (55) 19 3295 0407 Fax: (48) 91 4358 200 Phone: (46) 8 506 59500
Fax: (55) 19 3295 1025 Fax: (46) 8 506 59534
www.jlg.com