You are on page 1of 8

LARSEN & TOUBRO LIMITED

HED- HAZIRA MANUFACTURING COMPLEX

Coating Inspector Specific Examination

Candidate Name:

Signature:

Examinations start time:

Signature of
Total Marks Marks Obtained % Obtained Authorized
Evaluator
20

Instructions

1. This examination paper is having a total of 20 questions


2. All questions are multiple choice type
3. This examination is a open book exam and reference material shall be provided
4. All questions are to answered and carry equal marks.
5. There is no negative marks for wrong answer in this exam
6. Duration of the exam i8s 60 minutes
7. Encircle only one (1), which is the most correct answer
8. More than one circled choice will be considered as a wrong answer
9. In any change of answer, candidate should put signature near to that multiple choice, and
shall mark the earlier option with “X” mark to indicate cancellation of earlier multiple
choice
10. Candidate can use calculator if required
Coating Inspector Specific Examination

1. As per ASTM D 4285, the distance to be maintained between blotting paper and gun is
a. 12 inches
b. 24 inches
c. 30 inches
d. 26 inches
2. Which of the following methods should be used by inspector for visual assessment of
blast cleaned surface
a. Visual comparator
b. Profile gauge
c. Replica tape
d. All of the above
3. For area not exceeding 100 square meters, number area required for DFT measurement
a. 4
b. 6
c. 3 of area 10m2
d. 3 of area 25m2
4. As per ASTM D 4752, number of double rubs required to establish curing
a. 25
b. 60
c. 50
d. 52
5. MEK rub is performed on what type of paint
a. Zinc silicon primer
b. Inorganic Zinc
c. Silicon Aluminum
d. a & b
6. Application of zinc rich primer on job is a type
a. Sacrificial coatings
b. Barrier coatings
c. Inhibitive coatings
d. None of these
7. Meaning “St” according to IOS 8501-1
a. Blast cleaning
b. Hand and power tool cleaning
c. Flame cleaning
d. None of the above
8. On a windy day, while surface coating job was not covered properly, which of the
following defect may occur on the job
a. Orange Peal
b. Dry spray
c. Mud crack
d. Scratches
9. Equivalent standard of SSPC SP 10
a. ISO 8501 St 2.5
b. ISO 8501 Sa 2
c. ISO 8501 Sa 3
d. ISO 8501 Sa 2.5
10. Which of the following comes under SSPC AB 1 Type 2 category
a. Quartz
b. Copper slag
c. Garnet
d. All of the above
11. Which of the following standard refer to recycled abrasives
a. SSPC AB 1
b. SSPC AB 2
c. SSPC AB 3
d. None of the above
12. Holiday according to ASTM D 5162
a. Crack
b. Pinhole
c. Void
d. Discontinuity

13. Which of the following standard takes about Dry Film Thickness measurement
a. SSPC PA 2
b. SSPC Guide 15
c. ISO 2808
d. a & c
14. Stripe coat should be applied on
a. Corners
b. Holes
c. Joints
d. All of the above
15. For an area of 150mm2, how many spot readings are required
a. 15
b. 20
c. 25
d. 10
16. For an area of 210 mm2, hoe many gauge readings are required
a. 45
b. 50
c. 75
d. 60
17. Presence of which of the following shall not be cleaned as per SSPC SP 1
a. Oil
b. Grease
c. Soil
d. Mill scale
18. During ambient condition monitoring, steel temperature was observed to be 30 ºC and
humidity was found to be 85%. Painting is allowed when
a. Dew point temperature is 25 ºC
b. Dew point temperature is 26 ºC
c. Dew point temperature is 23 ºC
d. Painting shall not be performed
19. As per SC - OQWP – 01 who will maintain record of qualified blaster and painter
a. QC 3
b. AUX 2
c. AUX
d. QC 2
20. According to SC - CIWP – 01, which of the following is not the role of coating inspector
a. Verifying instrument calibration.
b. Performing hold point inspections in accordance with the applicable procedures.
c. Reviewing, organizing, and approving results of inspections
d. Supervising work of contactor
LARSEN & TOUBRO LIMITED
HED- HAZIRA MANUFACTURING COMPLEX

Coating Inspector General Examination

Candidate Name:

Signature:

Examinations start time:

Signature of
Total Marks Marks Obtained % Obtained Authorized
Evaluator
20

Instructions

1. This examination paper is having a total of 20 questions


2. All questions are multiple choice type
3. This examination is a open book exam and reference material shall be provided
4. All questions are to answered and carry equal marks.
5. There is no negative marks for wrong answer in this exam
6. Duration of the exam i8s 60 minutes
7. Encircle only one (1), which is the most correct answer
8. More than one circled choice will be considered as a wrong answer
9. In any change of answer, candidate should put signature near to that multiple choice, and
shall mark the earlier option with “X” mark to indicate cancellation of earlier multiple
choice
10. Candidate can use calculator if required
Coating Inspector General Examination

1. According to SC - CIWP – 01, experience required by a candidate to become coating


inspector
a.
2. In corrosion cell, material loss will occur in
a. Cathode
b. Anode
c. Electrolyte
d. None of the above
3. Which of the following is a method to control corrosion\
a. Material Selection
b. Design
c. a & b
d. none of the above
4. Which of the following is the function of pigment
a. Provide colour
b. Resist transmission of water vapor and oxygen
c. Decrease the permeability of film
d. a & d
5. Which of the following is not to prevent corrosion
a.
6. According to electrochemical series, the surface to be protected should be combined with
metal which is having
a.
7. During surface coating presence of moisture on the surface can cause
a. Can cause rusting
b. Will reduce the performance of applied paint
c. Can cause peel off
d. All of the above
8. Curing of zinc rich primer is aided by
a. High humidity and low temperature
b. Low humidity and low temperature
c. High humidity and high temperature
d. Low humidity and high temperature
9. In painting activity pot life refers to
a. Date of expiry of paint
b. Date of expiry of thinner
c. Date of expiry of mixed paint
d. Time which mixed paint is rendered spoiled
10. In electroch4emical corrosion of steel surfaces, which is considered as anode
a. Corroded surface
b. Moisture present on the job
c. Corrosion free surface
d. None of the above
11. A dead man is
a. Handle provided in compressor
b. Safety device provided in blasting gun
c. Safety device provided in painting gun
d. None of the above
12. Compressor compresses giv4es compressed air at a pressure of 7kg/cm2. If airless unit
has a pumping capacity of 1:30 calculate the pressure at nozzle tip
13. During qualification of blaster inspector should provide
a. Profile to be obtained
b. Area to be blasted
c. Arrangement of compressor
d. a & b
14. Dry Film Thickness (DFT) measurement instrument works on the principle of
a. Hall effect
b. Force needed to pull off
c. Eddy current
d. All of the above
15. In case of pre job conference
a. Meeting should be conducted and preceded by contractor
b. Meeting should be conducted and preceded by coating inspector
c. Meeting should be conducted contractor and preceded by coating inspector
d. Meeting should be conducted coating inspector and preceded by contractor
16. A minimum of how many hoses shall be present n a abrasive blasting machine
a. 4
b. 3
c. 2
d. 1
17. Which of the following is not a standard size blast nozzle orifice
a. ¼ inch
b. ½ inch
c. ¾ inch
d. 1 inch
18. Air-control equipment of conventional spray unit can modify or control
a. Volume of air
b. Air pressure
c. a and b
d. none of the above

You might also like