HAMEL
Instruments
MANUAL
Oscilloscope
HM 205-3Table of contents
Oscilloscope datasheet
Important!
with techn dees 1 Please be sue to read the salety information on pag
Mt and M22 before using this oncloscope!
Operating instretons
nant omtor ws
toot tend wh
Sete mh
Sporting condone me
Cente m3
Marterarce mo
Seki oe th rntne tae me
Rpocl hear whose m3
Npswshicovcnen m3
Relorene Une me
Tire Meosrements Me
Connector! Tot Sina me
ert Opraton m5
Tema Me
Fre corpenstion and use me
‘sscupperstn me
Iii Sotporenen me
opening ee a evra apis me
Span ms Oscilloscope
Brose dferencs measurement inGUAL mode Mio
Moos smentcton ample neclton to HM 205-3
Hegerngerd reo oe vas
Bees genes vit
fara gto va
Sepe va
Foi couing Vit2 Servic instructions
Micra ageing mr Conca $1
te Tagore Mit —_etument Cas Roova 8
Hers os sigs Mind Opumtng Vetoes 3
ea taaonn Wind Mtn on Mr Brass 3
gerne tats Aetgrrason 32
retire oho Mats Thegestwosece 33
cemoron Toss Mite Tedd Soot th asent 3
Soret Mite Replacements Comprar on Pais 3
TotEtons Miho Apecenes Bie’ eater 33
Storage Operation Circa Diagrams
oma cols une Spt Atenas
Seragr ese adopting weds Wie ete a Channel on
Sing che Sapoy Nine Yitemedoio Aplin Ch Ver, Chana action
Buse nade wizo _“ Hepormpiton Coronet Fs. 22
Batya One and atrnces vio) yerehtntr B3
Roloonce ne depoy M20 _Terease omega) Ba
Meneonaldehoctnst or icquonySonals |” MED Twegere sea Se Separator Be
Hehe ace ver Ee tater be
Ser woe Moe Ca Seu Unbking HV Suny 35
, Foor Sangh Cala: Be
Sterinsaion 1 Serna Gre OH XP) = BS
Foals fon ow x2 BlckDlua, Bo bre
Test instructions Tereoone gah 2
Stee 11 BAConverte B 3
Coho oy Tbe ihe Fas, Sig at Bi
rene Resor Betoions 71 ORCeneter be
Astgnats Check F} Raton! aos conto bie
Siorcey Dit of we Versa Ampito: oT} ND Carver 39
Chiveionhinevertca arr 1 Raw Ba
Samameten Romnca VeeiAmpifed, oT 2 —_ WaMEGBusroc 3
Oporng ees CH UAL AOD CHOP. component Locations
WWvehtanaX Operon”... 2 “SMP Beue ort
ThogeingChects 13 Tebow 222
Hosea 13 Zea rédoars 2a
Corpor fsir Th bietowe Bae
Yount 14 adjusting Pan
¥sce Nimo ra MS ws
Tit 20 tage Chocks Th be Aa
Gowan 290-2068Specification
Vertical Deflection
Operating mades: Chanel! r Chanel sparse.
heme! andi altsmota or oped
{Grenpa ewe anrox OM)
Samar aiforence tears Ch and Ch
{Ghonnell inverse)
v:Aode vi Chanel erd hanna analog).
Frequency range: 2x DC to 20Mie(~S48)
sonra pen 178ns,Ovrsoot =1%
Detection coficinte TOcaltete steps
fromsmwidy fo Bvivin 25 eoqunce,
‘esuanyineskoretedpeion: 3%
‘erable? 5:1 to mae 25
Y-magneation x [curate to imV/alv =5%
tregueney erge OC to 5M. 208)
Input impedones 4 2608
Input oupingr OC ~AC-GO (round
Input vote: max IOV IDC + pak AC}
Your em chlor Ch = domly nt 809.
Triggering
With Automatifrom 1OHs-40Nts (05d heigh)
‘armel it eve conta rm DC-4ONIHe,
‘Slope: positive or nogative.
ALT triggering LED indeation on tigger
Sours: Gh, Ch. ing, extemal
CCouping AC (=10H2- TOM, DC (0. 10M
LFO-2 tba, HE(=1 Skt 40M
‘ilggerlovel external =0:3V/ 1Miall25pF
‘Active TV-Syne Separator foie ana tame,
Horizontal Deflection
‘Time cootficionts(rattime): 21 cay. stops
tom 0 2us/dw 0 1siaw in 1-25 soquonce
Accuracy neared postion: #396
‘arable 25:1 tomax, 2 58/8,
‘rth X-oxpancion x10 (25%) fo 20m av 57%,
Holdoftame: vasste up t approx 10:1
Time coefficients (storage): Wcaibr steps
from fOnshtivwoSeisvin|-2- Ssoquonce,
wih X-expansionxt0 5%) to = Tusa
Bandwiath X-amplifir: DC-2 5MNe(~-343),
trout ampli Channa I,
‘Sersitwty se Chanel
ee pace sit <3" below 120K
Digital Storage
‘Operating modes: Reesh nd Single ith reset
‘bution and ready ED), Hod CHa, Chil.Dot Joiner.
‘Sampling rate: max. 20MHe or cach channel.
‘Memory size. 2040x8 bit foreach channel
Focoluton:vortcal28, herzartal200 sampls/dv.
expansion: x10 Derosol: 20 samploc/oN.
‘Analog/diital output{or HANES Graphic Printer,
‘and with eptions interface for X recorder.
‘Component Tester
Tost voltage: 72x. 85V open oct
Tost eurrent: max 2am, short out)
Test frequency: 50 or COV: line raquencyl
(One test load groundod (Safty Earth
General Information
CCRT: D14:384 P43/123, 6x 106m, 2KV,
Foctangular scroon, nina grateve.
‘Trace rottion:acjustati on front pana
Calibrator squaresvave 1kH2
forprobe compensation. Output: 0.2Va.2V 21%,
Ue voltages: 110,126,220, 240V~, + 10%.
Ma ambient tomporate: 10%. 40°C
Power consumption: ~ 46 Watt 50/60/<00H,
Protective system: Safety Classi (IEC S42),
\Wolght: approx. ka. Color techno brown,
(Cabinet: W 288, W145, 380mm,
‘Subjct to change without notice
Digital Storage Oscilloscope
Analog: 2 Channels DC-20MHz, max. 1mV/div., Comp.-Tester
Timebase 1s/div.-20ns/div., Trigger DC-40MHz.
Digital: Max. sampling rate 2x20MHz, Memory 2x 2048x8 bit,
Timebase 5s-1s/div., Dot-Joiner.
Now with a max. sampling rate of 20MHz and an improved storage depth
of 2048x8 bits per channel, the now HM205-3 has achieved a truly unique stan-
dard of performance. Compared to its predecessor model, which was already
the best-selling digital storage oscilloscope in Europe, the usable frequency
range for stored signals has been increased four-fold, The HM 205-3 is also indis
pensable for capture and display of long-term transients and extreme low-fre-
quency signals (<10H2} that are impossible to represent asa continuous, stable
trace on conventional realtime oscillascopes. By pressing the so called “DOT
JOIN” button, linear interpolation is used to connect the sampled points in
memory and achieve good waveform recognition even at 10x magnification.
‘The storage functions are exceedingly easy to operate. Simply press the
“STORE” bution to capture, digitize and store the signals subsequently arriving
at the scope input. In “refresh” mode the memory contents are updated with
every sweep. One-time non-recurring signals can be captured in “single”
mode. If, after data capture, the “HOLD” bution is pressed, the memory con-
tentsare “frozen. Ifthe scope is equipped with an optional interface, these can
then be cutout on the HAMEG Graphics Printer HM8148-2 or an X-Y recorder
(e.g. HAMEG optional accessory HO75 in this catalog), An IEEE-488 bus is avail-
able, as well 2s an extensive selection of software, for processing of data on
IBM-ATs, -XTs or compatibles (see options HO79-2 and SP91). Even with fre-
‘quent mode changes, the most recently captured waveforms remain stored in
memory until the instrument is powered down.
‘The HM205-3 is also generously equipped for analog applications. Its
outstanding attributes here include: excellent transient response up to 20MHz,
‘rigger bandwidth of atleast 40MHz, built-in component tester with single-but-
‘ton operation, variable “hold-off” period, and an active TV syne separator. Par-
ticularly when your job requires frequent switches between realtime and sam-
ppling modes, the superb efficiency and practicality of the new HM205-3 really
pay off,
Accessories supplied
Two 10:1 probes, Line cord, Operators Manual,