Professional Documents
Culture Documents
Units system: SI
Steel connections
Joints summary
___________________________________________________________________________________________________________________________
Joint types:
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Joint Member 1 Member 2 Member 3 Braces/Branches
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
BCF Beam Column -- --
BCW Beam Column -- --
BG Beam Girder -- --
BS Left beam Right beam -- --
CS Top column Bottom column -- --
CC Column Continuous beam -- --
CBB Column Right beam Left beam 1 brace mandatory
CVR Beam -- -- 1 brace mandatory
VXB -- -- -- All braces mandatory
CB Column -- -- --
HCBB Column Front beam Right beam 1 brace mandatory
HBBB Girder Beam -- 1 brace mandatory
HXB -- -- -- All braces mandatory
CHB Chord -- -- 1 branch mandatory
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
__________________________________________________________________________________________________________________
Joint : 1 - BCF ()
Design status : OK
__________________________________________________________________________________________________________________
Ratio : 0.62
Template(s) : MEP BCF DG16 Flush
Page1
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
Units system: SI
Steel connections
Loads summary
___________________________________________________________________________________________________________________________
Joint types:
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Joint Member 1 Member 2 Member 3 Braces/Branches
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
BCF Beam Column -- --
BCW Beam Column -- --
BG Beam Girder -- --
BS Left beam Right beam -- --
CS Top column Bottom column -- --
CC Column Continuous beam -- --
CBB Column Right beam Left beam 1 brace mandatory
CVR Beam -- -- 1 brace mandatory
VXB -- -- -- All braces mandatory
CB Column -- -- --
HCBB Column Front beam Right beam 1 brace mandatory
HBBB Girder Beam -- 1 brace mandatory
HXB -- -- -- All braces mandatory
CHB Chord -- -- 1 branch mandatory
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
__________________________________________________________________________________________________________________
Joint : 1 - BCF ()
Design status : OK
__________________________________________________________________________________________________________________
Ratio : 0.62
Template(s) : MEP BCF DG16 Flush
Page1
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
Units system: SI
Steel connections
Detailed report
___________________________________________________________________________________________________________________________
___________________________________________________________________________________________________________________________
MEMBERS
Configuration
Exists opposite connection : No
Beam
General
Beam type : Prismatic member
Beam section : H300X300
Beam material : A36
Horizontal angle (deg) : 0
Vertical angle (deg) : 0
Page1
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
MOMENT END PLATE
Connector
Four/Eight bolts on tension : 4 tension bolts
B: Width : 300 mm
L: Length : 510 mm
tp: Plate thickness : 25 mm
Plate material : A36
Fy : 0.248 kN/mm2
Fu : 0.4 kN/mm2
Hole type on plate : Standard (STD)
Beam side
Top flange weld type : Fillet
Top beam flange weld : E70XX
D1: Weld size to top beam flange (1/16in) : 5
Bottom flange weld type : Fillet
Bottom beam flange weld : E70XX
D3: Weld size to bottom beam flange (1/16in) : 5
Welding electrode to beam web : E70XX
D2: Weld size to beam web (1/16in) : 5
Support side
STIFFENERS
Transverse stiffeners
Section : PL 16x100x206
Position : Both
Full depth : Yes
bs: Transverse stiffeners width : 100 mm
cc: Corner clip length : 20 mm
cc: Corner clip width : 20 mm
ts: Transverse stiffener thickness : 16 mm
Material : A36
Weld type : Fillet
Welding electrode to support : E70XX
D: Weld size to support (1/16 in) : 5
Column web panel zone stiffeners
Page2
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
Section : PL 8x214x330
Stiffener type : Doubler plate
Position : Both sides
Flush : No
Width : 214 mm
Length : 330 mm
ts: Stiffener thickness : 8 mm
Material : A36
Weld type to column flange : Fillet
Welding electrode to support : E70XX
D: Weld size to support (1/16 in) : 5
DEMANDS
Beam Right beam Left beam Column Panel
Description Ru Pu Mu PufTop PufBot PufTop PufBot Pu Vu Load type
[KN] [KN] [KN*m] [KN] [KN] [KN] [KN] [KN] [KN]
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CB1 111.00 15.00 146.00 -504.78 519.78 0.00 0.00 0.00 519.78 Design
CB2 111.00 -15.00 146.00 -519.78 504.78 0.00 0.00 0.00 519.78 Design
CB3 -111.00 15.00 146.00 -504.78 519.78 0.00 0.00 0.00 519.78 Design
CB4 -111.00 -15.00 146.00 -519.78 504.78 0.00 0.00 0.00 519.78 Design
CB5 111.00 15.00 -146.00 519.78 -504.78 0.00 0.00 0.00 519.78 Design
CB6 111.00 -15.00 -146.00 504.78 -519.78 0.00 0.00 0.00 519.78 Design
CB7 -111.00 15.00 -146.00 519.78 -504.78 0.00 0.00 0.00 519.78 Design
CB8 -111.00 -15.00 -146.00 504.78 -519.78 0.00 0.00 0.00 519.78 Design
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Page3
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Vertical bolt spacing (external flange) [mm] 135.00 64.00 -- Sec. J3.3
smin = 8/3*d
= 8/3*24[mm]
= 64[mm] Sec. J3.3
Vertical bolt spacing (internal flange) [mm] 135.00 64.00 -- Sec. J3.3
smin = 8/3*d
= 8/3*24[mm]
= 64[mm] Sec. J3.3
Horizontal center-to-center spacing (gage) [mm] 140.00 64.00 300.00 Sec. J3.3,
DG4 Sec. 2.4,
DG4 Sec. 2.1,
2.4,
DG16 Sec. 2.5
gmin = Max(8/3*d, 2*k1c + 2*d, twb + 2*w + dh)
= Max(8/3*24[mm], 2*4.5[mm] + 2*24[mm], 10[mm] + 2*7.94[mm] + 25.59[mm])
= 64[mm] Sec. J3.3,
DG4 Sec. 2.4
gmax = bfb
= 300[mm] DG4 Sec. 2.1,
2.4,
DG16 Sec. 2.5
Outer bolt distance (external flange) [mm] 60.00 36.70 -- DG4 Sec. 2.1
d< = 1 [in] ® 24[mm]<
= 1 [in] ® True
Inner bolt distance (external flange) [mm] 60.00 36.70 -- DG4 Sec. 2.1
d< = 1 [in] ® 24[mm]<
= 1 [in] ® True
Outer bolt distance (internal flange) [mm] 60.00 36.70 -- DG4 Sec. 2.1
d< = 1 [in] ® 24[mm]<
= 1 [in] ® True
Page4
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Inner bolt distance (internal flange) [mm] 60.00 36.70 -- DG4 Sec. 2.1
d< = 1 [in] ® 24[mm]<
= 1 [in] ® True
Support
Horizontal edge distance [mm] 55.00 41.65 152.40 Sec. J3.5
Lemin = edmin + C2
= 41.65[mm] + 0[mm]
= 41.65[mm] Tables J3.4,
J3.5
Support
Web thickness [mm] 9.00 6.77 -- p. 9-5
1/2
tmin = (0.6*FEXX*(2) /2*D/16 [in])/(0.6*Fu)
1/2
= (0.6*482.63[N/mm2]*(2) /2*5/16 [in])/(0.6*399.89[N/mm2])
= 6.77[mm] p. 9-5
HasWeldsOnBothSides ® True
tmin = tmin
= 6.77[mm] p. 9-5
Transverse stiffeners
Length [mm] 206.00 103.00 -- Sec. J10.8
lsmin = (dc - 2*tcf)/2
= (250[mm] - 2*22[mm])/2
= 103[mm] Sec. J10.8
Page5
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Doublers
Recommended thickness for beveling and welding [mm] 8.00 3.18 -- Sec. G2.1,
DG 13 Eq. 4.4-4
h = dc - 2*k
= 250[mm] - 2*14[mm]
= 222[mm] Sec. G2.1
1/2
tmin = h/(1.1*(5*E/Fy) )
1/2
= 222[mm]/(1.1*(5*2.00E+05[N/mm2]/248.21[N/mm2]) )
= 3.18[mm] Sec. G2.1
tmin = k - tf - re
= 14[mm] - 22[mm] - 3.18[mm]
= -11.18[mm] DG 13 Eq. 4.4-4
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
pfi = min(pfi, s)
= min(60[mm], 102.47[mm])
= 60[mm] DG4 Table 3.1,
AISC 358-05 Table 6.2
de< = s ® 45[mm]<
= 102.47[mm] ® True
Page6
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
fMn = (fb*Mn)/1.11
= (0.9*470.82[kN*m])/1.11
= 381.74[kN*m] DG4 Eq. 3.10,
Sec. 2.2.3
No prying bolt moment strength [KN*m] 239.81 148.14 CB5 0.62 DG4 Eq. 3.7,
Eq. 3.8,
DG4 Eq. 3.7
Mnp = 2*Pt*(h0 + h1)
= 2*280.48[kN]*(352.5[mm] + 217.5[mm])
= 319.75[kN*m] DG4 Eq. 3.7,
Eq. 3.8
fMn = f*Mnp
= 0.75*319.75[kN*m]
= 239.81[kN*m] DG4 Eq. 3.7
fRn = C*fRn
= 4*112.19[kN]
= 448.77[kN] Tables (7-1..14)
Bolt bearing under shear load [KN] 1443.33 111.00 CB1 0.08 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 45[mm] - 25.59[mm]/2)
= 32.21[mm] Sec. J3.10
Page7
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
pfi = min(pfi, s)
= min(60[mm], 102.47[mm])
= 60[mm] DG4 Table 3.1,
AISC 358-05 Table 6.2
de< = s ® 45[mm]<
= 102.47[mm] ® True
fMn = (fb*Mn)/1.11
= (0.9*470.82[kN*m])/1.11
= 381.74[kN*m] DG4 Eq. 3.10,
Sec. 2.2.3
No prying bolt moment strength [KN*m] 239.81 148.14 CB1 0.62 DG4 Eq. 3.7,
Eq. 3.8,
DG4 Eq. 3.7
Mnp = 2*Pt*(h0 + h1)
= 2*280.48[kN]*(352.5[mm] + 217.5[mm])
= 319.75[kN*m] DG4 Eq. 3.7,
Eq. 3.8
fMn = f*Mnp
= 0.75*319.75[kN*m]
= 239.81[kN*m] DG4 Eq. 3.7
fRn = C*fRn
= 4*112.19[kN]
= 448.77[kN] Tables (7-1..14)
Bolt bearing under shear load [KN] 1443.33 111.00 CB1 0.08 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 45[mm] - 25.59[mm]/2)
= 32.21[mm] Sec. J3.10
Page8
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Beam
Web weld shear strength [KN] 329.12 111.00 CB1 0.34 Eq. J2-4
Fw = 0.6*FEXX
= 0.6*482.63[N/mm2]
= 289.58[N/mm2] Sec. J2.4
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*5/16 [in]*135[mm]
= 757.71[mm2] Sec. J2.4
fRn = 2 * (f*Fw*Aw)
= 2 * (0.75*289.58[N/mm2]*757.71[mm2])
= 329.12[kN] Eq. J2-4
Web weld strength to reach yield stress [KN/m] 3656.94 2233.89 CB1 0.61 Eq. J2-4,
Eq. J4-1
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
1/2
fRw = 2 * (f*Fw*(2) /2*D/16 [in])
1/2
= 2 * (0.75*434.37[N/mm2]*(2) /2*5/16 [in])
= 3.66[kN/mm] Eq. J2-4
fRn = f*Fy*tw
= 0.9*248.21[N/mm2]*10[mm]
= 2.23[kN/mm] Eq. J4-1
fRn = f*0.60*Fy*Ag
= 1*0.60*248.21[N/mm2]*3000[mm2]
= 446.78[kN] Eq. J4-3
Flange weld capacity (external flange) [KN] 1133.65 519.78 CB2 0.46 Eq. J2-4
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*5/16 [in]*620[mm]
= 3479.85[mm2] Sec. J2.4
Page9
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
fRn = f*Fw*Aw
= 0.75*434.37[N/mm2]*3479.85[mm2]
= 1133.65[kN] Eq. J2-4
Flange weld capacity (internal flange) [KN] 1133.65 519.78 CB1 0.46 Eq. J2-4
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*5/16 [in]*620[mm]
= 3479.85[mm2] Sec. J2.4
fRn = f*Fw*Aw
= 0.75*434.37[N/mm2]*3479.85[mm2]
= 1133.65[kN] Eq. J2-4
Support
Flexural yielding (external flange) [KN*m] 265.47 148.14 CB5 0.56 DG4 Eq. 3.20,
Sec. 2.2.3
1/2
s = 0.5*(bp*g)
1/2
= 0.5*(250[mm]*140[mm])
= 93.54[mm] DG4 Table 3.1,
AISC 358-05 Table 6.2
fMn = (fb*Mn)/1.11
= (0.9*327.41[kN*m])/1.11
= 265.47[kN*m] DG4 Eq. 3.20,
Sec. 2.2.3
Support bolt bearing (external flange) [KN] 1270.13 111.00 CB1 0.09 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 45[mm] - 25.59[mm]/2)
= 32.21[mm] Sec. J3.10
Page10
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Flexural yielding (internal flange) [KN*m] 312.22 148.14 CB1 0.47 DG4 Eq. 3.20,
Sec. 2.2.3
1/2
s = 0.5*(bp*g)
1/2
= 0.5*(250[mm]*140[mm])
= 93.54[mm] DG4 Table 3.1,
AISC 358-05 Table 6.2
fMn = (fb*Mn)/1.11
= (0.9*385.07[kN*m])/1.11
= 312.22[kN*m] DG4 Eq. 3.20,
Sec. 2.2.3
Support bolt bearing (internal flange) [KN] 1520.24 111.00 CB1 0.07 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 135[mm] - 25.59[mm]/2)
= 122.21[mm] Sec. J3.10
Panel web shear [KN] 837.71 519.78 CB1 0.62 Sec. J10-6,
Eq. J10-9
Pc = f*Fy*A
= 1*248.21[N/mm2]*10926[mm2]
= 2711.94[kN] Sec. J10-6
IsPanelZoneDeformationConsidered = IsPanelZoneDeformationConsidered
= False Sec. J10-6
Page11
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
fRn = f*0.60*Fy*dc*tw
= 0.9*0.60*248.21[N/mm2]*250[mm]*9[mm]
= 301.58[kN] Eq. J10-9
fRndp = 2 * (f*0.6*Fy*dc*tp)
= 2 * (0.9*0.6*248.21[N/mm2]*250[mm]*8[mm])
= 536.13[kN] DG13 Eq. 4.4-1
N=N
= 30.88[mm] Sec. J10-2
IsMemberEnd ® True
IsMemberEnd ® True
fRnts = 2 * (f*Fy*Ast)
= 2 * (0.9*248.21[N/mm2]*1280[mm2])
= 571.88[kN] DG13 Eq. 4.3-1
Page12
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
fRn = f*Fy*Ag
= 0.9*248.21[N/mm2]*2560[mm2]
= 571.88[kN] Eq. D2-1
Ag = Lp*tp
= 80[mm]*16[mm]
= 1280[mm2] Sec. D3-1
fPn = 2 * (f*Fcr*Ag)
= 2 * (0.9*237.47[N/mm2]*1280[mm2])
= 547.13[kN] Sec. J4.4
Flange weld capacity [KN] 527.06 226.19 CB2 0.43 Eq. J2-4
L = bst - clip - w
= 100[mm] - 20[mm] - 7.94[mm]
= 72.06[mm] Comm. J10.8
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*5/16 [in]*72.06[mm]
= 404.46[mm2] Sec. J2.4
fRn = 4 * (f*Fw*Aw)
= 4 * (0.75*434.37[N/mm2]*404.46[mm2])
= 527.06[kN] Eq. J2-4
Page13
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Web weld capacity [KN] 868.22 226.19 CB2 0.26 Eq. J2-4
L = l - clip - w
= 206[mm] - 20[mm] - 7.94[mm]
= 178.06[mm] Comm. J10.8
Fw = 0.6*FEXX
= 0.6*482.63[N/mm2]
= 289.58[N/mm2] Sec. J2.4
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*5/16 [in]*178.06[mm]
= 999.4[mm2] Sec. J2.4
fRn = 4 * (f*Fw*Aw)
= 4 * (0.75*289.58[N/mm2]*999.4[mm2])
= 868.22[kN] Eq. J2-4
fRn = f*Fy*Ag
= 0.9*248.21[N/mm2]*2560[mm2]
= 571.88[kN] Eq. D2-1
Ag = Lp*tp
= 80[mm]*16[mm]
= 1280[mm2] Sec. D3-1
fPn = 2 * (f*Fcr*Ag)
= 2 * (0.9*237.47[N/mm2]*1280[mm2])
= 547.13[kN] Sec. J4.4
Flange weld capacity [KN] 527.06 39.53 CB1 0.07 Eq. J2-4
L = bst - clip - w
= 100[mm] - 20[mm] - 7.94[mm]
= 72.06[mm] Comm. J10.8
Page14
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*5/16 [in]*72.06[mm]
= 404.46[mm2] Sec. J2.4
fRn = 4 * (f*Fw*Aw)
= 4 * (0.75*434.37[N/mm2]*404.46[mm2])
= 527.06[kN] Eq. J2-4
Web weld capacity [KN] 868.22 39.53 CB1 0.05 Eq. J2-4
L = l - clip - w
= 206[mm] - 20[mm] - 7.94[mm]
= 178.06[mm] Comm. J10.8
Fw = 0.6*FEXX
= 0.6*482.63[N/mm2]
= 289.58[N/mm2] Sec. J2.4
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*5/16 [in]*178.06[mm]
= 999.4[mm2] Sec. J2.4
fRn = 4 * (f*Fw*Aw)
= 4 * (0.75*289.58[N/mm2]*999.4[mm2])
= 868.22[kN] Eq. J2-4
NOTATION
A: Column cross-sectional area
Ab: Nominal bolt area
Ag: Gross area
Ast: Transverse stiffener cross-sectional area
Aw: Effective area of the weld
b: Plate, connector or member width
bcf: Width of column flange
bfb: Beam flange breadth
bp: Plate width
bs: Transverse stiffener width
bsmin: Minimum transverse stiffener width
bst: Contact length between transverse stiffener and support flange
N: Bearing length
C: Bolt group coefficient
C2: Edge distance increment
c: Vertical bolt spacing
clip: Transverse stiffener corner clip dimension
d: Nominal bolt diameter
dbmax: Maximum bolt diameter
de: Distance from the first bolt row to the top plate edge
dh: Nominal hole dimension
d: Beam depth
dc: Column depth
Page15
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
NOTATION
D: Number of sixteenths of an inch in the weld size
E: Elastic modulus
Fcr: Critical stress, flexural stress buckling
Fe: Elastic critical buckling stress
FEXX: Electrode classification number
Fnv: Nominal shear stress
Fu: Specified minimum tensile strength
Fw: Nominal strength of the weld metal per unit area
Fy: Specified minimum yield stress
Fyb: Specified minimum yield stress of beam, plate or branch material
Fyc: Specified minimum yield stress of column material
Fyp: Specified minimum yield stress of plate
Fys: Specified minimum yield stress of stiffener material
Fyw: Specified minimum yield stress of web
g: Transversal gage between bolts
gmax: Maximum bolt gage
gmin: Minimum bolt gage
h: Clear distance between flanges
h0: Distance from the centerline of a compression flange to the tension side outer bolt row
h0: Distance from the centerline of the beam compression flange to the centerline of the 0 tension bolt row
h1: Distance from the centerline of a compression flange to the tension side inner bolt rows
h1: Distance from the centerline of the beam compression flange to the centerline of the 1 tension bolt row
hst: Stiffener height
HasOppositeConnection: Has opposite connection
HasPlateThickBehaviour: The plate has thick behavior
HasWeldsOnBothSides: Has welds on both sides
IsBeamReaction: Is beam reaction
IsMemberEnd: Is member end
IsPanelZoneDeformationConsidered: Is panel zone deformation considered on frame stability
K: Effective length factor
k1: Bearing factor
k1c: Distance from column web centerline to flange toe of fillet
k2: Bearing factor
k: Distance from outer face of flange to the web toe of fillet
k: Outside corner radius
l: Length
L: Length
Lc-end: Clear distance
Le: Edge distance
Lemax: Maximum edge distance
Lemin: Minimum edge distance
Lev: Vertical edge distance
Lp: Plate length
lsmin: Stiffener minimum length
L: Length of weld
LoadAngleFactor: Load angle factor
Mn: Nominal moment
Mnp: No prying moment
Mpl: End plate or column flange flexural strength
edmin: Minimum edge distance
n: Bolts rows number
N: Bearing length
nc: Number of bolt columns
Pc: Available axial compressive strength
pf0: Distance from the inside of a beam tension flange to the nearest outside bolt row
pfi: Distance from the inside of a beam tension flange to the nearest inside bolt row
pfmin: Minimum distance from the inside of a beam tension flange to the nearest inside bolt row
P r: Required axial stress
ps0: Distance from the outside face of column stiffener to the nearest outside bolt row
psi: Distance from the inside face of column stiffener to the nearest inside bolt row
Pt: Bolt tensile strength
f: Design factors
fb: Design factor for bending
fMn: Design or allowable strength
fPn: Design or allowable strength
fRn: Design or allowable strength
fRn: Design or allowable strength per unit length
fRndp: Doubler plate design or allowable strength
fRnts: Transverse stiffener design or allowable strength
Page16
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
NOTATION
fRw: Fillet weld capacity per unit length
Q: Prying action coefficient
r: Radius of gyration
re: Permissible encroachment
s: Distance from the most inside or outside tension bolt row to the edge of a yield line
smin: Minimum spacing
s: Longitudinal bolt spacing
Lc-spa: Distance between adjacent holes edges
tp: Thickness of the connected material
tbf: Thickness of the flange
tcf: Thickness of the column flange
tf : Thickness of the loaded flange
tmin: Minimum thickness
tp: Plate thickness
tsmin: Minimum transverse stiffener thickness
tsmin: Minimum plate stiffener thickness
tw: Web thickness
twb: Thickness of beam web
q: Load angle
wmin: Minimum weld size required
wmin: Minimum weld size required
w: Weld size
Yc: Column yield line mechanism parameter
Yp: Yield line mechanism parameter
Page17
60006-POS-CAL-SF-No4-B2-BCF-H300x300-7mmWeld-R0
Units system: SI
Steel connections
Connections elements summary
___________________________________________________________________________________________________________________________
CONNECTION ELEMENTS
Plates
ID Plate Material Length Width Thickness Qty.
[mm] [mm] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
P0 PL 25x300x510 A36 510.00 300.00 25.00 1
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Bolts
ID Bolt Grade Length Diameter Qty.
[mm] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
B0 M24 A325M G8_8 47.00 24.00 8
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Welds
ID Weld Type Strength Size Length
[KN/mm2] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
W0 E70XX Fillet 0.48 7[mm] 1720.00
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Element Description ID
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Bolts - Support side M24 A325M B0
Plate - Support side PL 25x300x510 P0
Weld - Beam side E70XX W0
Weld - Beam side E70XX W0
Weld - Beam side E70XX W0
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Notes
Joint type:
BCF : Beam - Column flange
Connector type:
MEP : Moment end plate
Page1