Professional Documents
Culture Documents
Heavy duty type tie rod end AYP# 109851X, MTD# 923-0351
D 22-01 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
HEX HEAD SELF UNIVERSAL continued
Part# O.E.M Application Part# O.E.M Application
HEX HEAD SELF TAPPING BOLTS 255-216
Part# OEM# Thread Size Length Clutch Collar
Used to secure clutches to
285-466 Universal 5/16”-18 3/4” crankshaft and jackshafts.
Measures: 3/4” ID X 1-1/4” OD X 3/8” HT.
285-467 Universal 5/16”-18 1” Includes set screw.
285-468 Universal 5/16”-18 1-1/2”
260-000
285-469 Universal 3/8”-16 1”
Key Stock
285-470 Universal 3/8”-16 1-1/4” Size: 3/16” (Sold in 12” lengths)
260-034
285-478
285-387
Steering Wheel Linch Pin
Found on many Lawn and Size: 3/16” diameter
Garden Tractors. Replaces X 1-1/4” pin length
Ariens and Toro / Wheel Horse (under head)
- deep dish type.
Mounting hole: 3/4” ID X 13” OD X 7-1/2” HT 285-388
Linch Pin
285-482 Size: 1/4” diameter
X 1-3/4” pin length
Steering Wheel (under head)
Used on many Go-Carts etc.
Three 1/4” mounting holes, 285-389
1-3/8” centre to centre X 1/2” ID X 10” OD. Linch Pin
Size: 5/16” diameter
235-127 X 1-3/4” “D” style pin
(under head)
D 22-02 D
DRIVE, RIDER & PUSHMOWER PART Banta
UNIVERSAL continued UNIVERSAL continued
Part# O.E.M Application Part# O.E.M Application
285-361 420-150
Seat Cover
Wheel Height Adjuster Set Fits our 420-000 tractor
Deluxe adjuster sets to 9 seat (6” back height)
positions. Easy adjusting,
just pull out and snap.
Mounts front or rear, 420-350
left or right side. Each set includes
(4) each of the following - mounting bolts, adjustment Seat Cover
plates, adjusting arms and mounting arms. Fits our 420-026 tractor
seat (7-3/4” back height)
285-320
420-560
Deck Spacer Rings
Measures: 1/4” thick Seat Cover
X 7-1/8” ID X 8-7/8” OD Fits our 420-042 tractor seat
(While Quantities Last) (15” back height)
285-338
Seat Covers are an inexpensive alternative to seat replace-
Deck Spacer Rings ment. Ideal for tractor seats that have ripped or torn seats.
Prevents wet bottoms caused by wet exposed foam cushions.
Measures: 1/2” thick Seat Covers are gas, oil and abrasion resistant. NOTE: Back
X 7-1/8” ID X 8-7/8” OD height measurement - inside seat back to top of seat back.
(While Quantities Last)
285-346 420-000
Deck Spacer Rings
Measures: 3/4” thick Tractor seat - Low Back
X 7-1/8” ID X 8-7/8” OD Fits Ariens, AYP, Bolens,
(While Quantities Last) Gilson, MTD, Murray,Snapper,
Toro/ Wheel Horse to mention
Used to adjust engine mounting height on decks and tillers. a few. Spring mount - centre
Also strengthens mounting plate with one 1/2”-13 weldnut.
circle on steel decks. Fits all 8” bolt circle engine mounts. Made by an OEM supplier.
Available in three different Size: 6” HT X 14-1/2” D X 16-3/4” W
thicknesses. Made of heavy cast aluminum material. (Use with our 420-150 seat cover.)
365-072 420-026
D 22-03 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
ARIENS ARIENS continued
Part# O.E.M Application Part# O.E.M Application
ARIENS
3625000 / 3615400
Quill Assembly
245-027 21084 Includes: 5” diameter pulley
723-0156 X 1/2” “V” width, housing, ball
bearings (230-037), blade
Ball Joint adaptor hub, spacer, washer,
3/8”-24 X 7/8” Right bearing slinger,blade adaptor/trim.
hand male thread, 3/8”-24 RH female. Size: 4-13/16” Overall height,
Blade saddle: 2-9/16” W,
245-214 10247 Thread size: 3/4”-10 UNC (blade bolt NOT included)
Quill assembly comes complete with all parts listed above. Ariens
Ball Joint does not sell as a complete set.
Measures 2” long with a 1/4” hole. Fits most 40” decks LH side (large pulley)
(While Quantities Last)
285-211 3615300 / 5412000
285-551 83192 6444200 / 3037500
3625000 / 2526400
0341900 / 3485500
Deck Spring Quill Assembly
For all riders since 1972. Includes: 4-3/4 diameter pulley
Fits models 830, 1030, 1130 and 1132. X 1/2” “V” width, housing, ball
Measures: 6-5/8” overall length X 4-1/2” coil length. bearings (230-037),
blade adaptor hub,
780-004 83004 spacer, washer,
bearing slinger, blade adaptor/trim.
Size: 4-3/4” Overall height, Blade saddle: 2-9/16” W,
Idler Spring Thread size: 3/4”-10 UNC (blade bolt NOT included)
Measures: 4-7/8” overall length X 4-1/4” coil length.
Quill assembly comes complete with all parts listed above. Ariens
does not sell as a complete set.
Fits most 40” decks RH side (small pulley).
D 22-04 D
DRIVE, RIDER & PUSHMOWER PART Banta
AYP- Roper / Sears / Husqvarna AYP continued
Part# O.E.M Application Part# O.E.M Application
416-029 1200029
12000029
Klip Ring
240-935 750688
Fits King pin on 16, 18 and 20 Hp
Garden Tractors built from 1991
Drive Disc
to present. Also used to retain steering belcrank assembly
Fits self propelled mowers.
on 16 Hp Garden Tractor, & retain sector on 18, 20 Hp
Measures: 1/2” ID X 4-1/8” OD
models. Fits 2/4” shaft.
X 1-1/8” overall height
D 22-05 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
AYP continued AYP continued
Part# O.E.M Application Part# O.E.M Application
D 22-06 D
DRIVE, RIDER & PUSHMOWER PART Banta
AYP continued AYP continued
Part# O.E.M Application Part# O.E.M Application
285-242 187291
532-187291
Shaft assembly
Only for our 285-341 (housing) Quill Assembly
and 285-426 quill assemblies. Fits 1985 thru 1993, 44” & 50” cut. Primary Centre quill
Includes: Shaft with (1) 230-060 and (1) 230-029 spindle on 20 Hp 50” cut models. Fits models 4200-14, 951940,
bearings, grass shield and zerk fitting. Fits Craftsman lawn 8208A29 and TS2050A. Uses our 230-060 replacement
tractor quill assemblies found on YS4500 with 42” cut, 23 bearing.
Twin cylinder, for model# 944-606951. Will replace AYP#
192872 but this one has a grease fitting. 285-031 121676X / 121687X
105891X / 917-254791 / 532-121687
285-495 121705X / 121795X
121704X / 106040X / 106041X
Quill Assembly
Quill Assembly Fits 1985 thru 1991, 38” cut models, 2-1/4” blade saddle.
Fits 1986 thru 1993 18 Hp 44” cut. Yard Tractor model Made with the brake lip. Uses our 230-060 replacement
Y1844A, Y1844B and YE16H44C, and GT2500BR, bearing and our 285-348 self-tapping bolts.
GT2500CR, RL1844B and PC18144A. Primary Quill on
44” cut decks. Uses our 230-060 replacement 285-213 101477X / 677A233
bearing and our 285-348 self-tapping bolts. 677A14 / 677A181 / 532 10 14-77
Quill Assembly
Fits 1985 thru 1993, 20 Hp, 50” cut tractor models and 44” Quill Assembly
yard tractors Y2050C, Y1844A, Y1844B and YE16H44C. Fits 1980 thru 1984, 36” and 38” cut models, 2-1/2”
Secondary, Centre and Left side; also fits models blade saddle. Made with the brake lip; also found on
GT2500BR, GT2500CR, RL1844B and PC1844A. models L0815DR 1999 and older. Uses our 230-060
Also fits 20 Hp, 50” cut models 4200-14 & 951940. replacement bearing and 285-348 self-tapping bolts.
D 22-07 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
AYP continued AYP continued
Part# O.E.M Application Part# O.E.M Application
Quill Assembly
Fits 44”, 46” and 50” ventilated Spindle Shaft Assembly
decks. Decks using star Replacement shaft assembly
shaped (new Y design) for our 285-353 quill / spindle assembly. Fits 36” 38” and
center hole blades. 42” vented decks. Star shaped blade mount, double hex
Use our 230-060 (upper) external spline for pulley. Includes: (1) 230-060 Upper and
& 230-029 (lower) (1) 230-029 Lower bearings. Uses our 416-729 Nut.
replacement bearings.
Use our 275-863, 275-862 285-365 165579
& 275-861 pulleys. 532-165579
285-356 137152
Quill Assembly
532 1371-52
Fits 36” rear discharge
mowers. Includes: pulley
Quill Housing Only nut, bolt and washer.
Fits 44” and 50” ventilated Uses our 285-237
decks using star shaped spindle shaft and our
(New “Y” design) 410-086 blade bolt.
centre hole blades.
NOTE: Same housing as our 285-353 Quill Assembly
285-234 137553 with a different Spindle Shaft.
Shaft uses a 3/8 - 24 X 1-1/4” Left Hand Threaded
blade bolt. (Part# 410-086)
Spindle Shaft Assembly only
Fits 44”, 46” and 50” 410-086 165484
vented decks. Star shaped
blade mount, double hex Blade Bolt
external spline for pulley. Left hand thread
285-237 165482
285-353 130794 532-165482
532 13 07-94
Spindle Shaft Assembly
Quill Assembly Fits our 285-365 Quill Assembly.
Fits 36”, 38” and 42” Includes: (1) 230-029 bearing and (2) washers. Uses our
ventilated decks using star 410-086 Left Hand Thread blade bolt & 416-729 pulley nut.
shaped (New “Y” design)
centre hole blades. Includes:
pulley nut, bolt and washer. 416-729 137266
Uses our 285-231 spindle
129729
shaft and our replacement Lock Nut
spindle shaft bearings Fits our 285-231, 285-234 and
230-060 (top) and 230-029 285-237 spindle shaft assemblies;
(bottom); and our 285-347 self-tapping bolts. also fits our John Deere quill / shindle
NOTE: Our most Common Spindle Assembly assemblies 285-905, 285-905 and 285-907.
uses a 3/8” - 24 Right Hand threaded blade bolt. Size: 1-1/4” OD built in washer X 3/4” HT X 1/2”-18 thread
D 22-08 D
DRIVE, RIDER & PUSHMOWER PART Banta
AYP continued BOBCAT
Part# O.E.M Application Part# O.E.M Application
285-809 36006N
Latch Assembly with Hook Exmark 302030
Jacobsen 552188
For 42” and 46” decks. Snapper 7-6379
Use (2) per deck to hold on mulching cover plate. Snapper 5-9759
Overall length of the rubber strap is 4-3/4” Snapper 362024
Quill Assembly
230-747 155066 / 174284 For Bobcat, Kees, Exmark, Jacobsen
and Snapper mowers. Fits 32” & 36” cut decks with short
Roller Cam Assembly shaft. Also fits outside spindle of 48” cut Exmark models.
For AYP 42” decks. Size: 5-3/16” shaft length X 5/8” ID X 1” OD shaft.
Measures: .582” OD X 1/4” ID X 3/8” HT
(Use with our 235-130 Shoulder Bolt - see page 22-06) 245-008 36129
Exmark 1-302122
John Deere PT8663
Kees 362100
245-315 139868
Caster Yoke Support Arm
Bobcat and other Mfg.
Measures: 3/4” ID for caster yoke shaft, 3/8” mounting
holes. Used with our 245-006 caster yoke
BUNTON
Rear Suspension Arm
For mower deck lift on lawn tractors with 38”, 42”,
44” 46” and 50” decks. Measures: 11-1/2” long X 1-1/8” W,
(2) 1/2” centre holes on 10-1/2” centres. 285-217 PAL0806A
PL06140A / PL4606A
D 22-09 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
BUNTON continued EXMARK continued
Part# O.E.M Application Part# O.E.M Application
D 22-10 D
DRIVE, RIDER & PUSHMOWER PART Banta
EXMARK continued EXMARK continued
Part# O.E.M Application Part# O.E.M Application
D 22-11 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
EXMARK continued EXMARK continued
Part# O.E.M Application Part# O.E.M Application
PTO Switch
Fits model Lazer Z Quill Assembly
2 position, 8 terminals Fits 72” decks on Lazer Z models.
Pulley diameter: 8” OD X 1” HT,
285-809 1-302030 Overall height: 8-1/8”. H.D. diecast construction.
302030 (Top of pulley nut to bottom of shaft).
Bobcat 36006N
Kees 362024
Jacobsen 552188 285-950 1032533 / 1032547
1038280 / 1323532
Quill Assembly 1513016 / 1634619
With short shaft. Shaft length:
5-3/16” Fits 32” and 36” decks, also fits 48”
cut outside spindles. Uses (2) of our 230-086 bearings. Quill Assembly Housing ONLY
Size: 5-3/16” shaft length X 5/8” ID X 1” OD shaft. Fits later models Lazer Z Hp,
Metro, Viking, Turf Trace and
285-917 1-402006 Turf Ranger decks; 44”, 48” and 52” cut decks.
402006 Size: 1” ID X 5-1/4” OD X 3-3/4” HT. Includes: Bearings,
Kees 59964 Spacers and grease zerk. Note: Pulley and shaft not included.
Kees 76645 (Uses our 230-233 spindle bearing).
285-946 103-1184
Quill Assembly
Fits 52” decks on
Lazer Z HP models.
Pulley diameter: 6-5/8” OD Quill / Spindle assembly
X 1” HT, Overall height: 7-7/8”. Fits 48” decks on Lazer Z HP models. Pulley diameter:
(Top of pulley nut to bottom of shaft). 5-3/8” OD X 1” HT, Overall height: 7-7/8”. (Top of pulley
H.D. diecast construction. nut to bottom of shaft). H.D. diecast construction.
285-947 103-3200
285-944 103-1183
Quill Assembly NEW
Fits 60” decks on
Lazer Z XP / HP series models.
Pulley diameter: 6-1/2” OD X 7/8” HT,
Overall height: 8-1/8”.
(Top of pulley nut to bottom of shaft).
H.D. diecast construction.
285-948 103-3206
Quill Assembly
Fits 72” decks on Quill / Spindle assembly
Lazer Z XP series models. Fits 44” decks on Lazer Z HP models. Pulley diameter:
Pulley diameter: 8” OD X 7/8” HT, 5-7/8” OD X 1.00” HT, Overall height: 7-7/8”.
Overall height: 8-1/8”. H.D. diecast construction. (Top of pulley nut to bottom of shaft). H.D. diecast
(Top of pulley nut to bottom of shaft). construction.t
D 22-12 D
DRIVE, RIDER & PUSHMOWER PART Banta
EXMARK continued HONDA continued
Part# O.E.M Application Part# O.E.M Application
285-941 1031140
JOHN DEERE
NEW
245-008 PT8663
Quill / Spindle assembly
Fits 48” decks on Lazer Z HP Caster Yoke Support Arm
models. Pulley diameter: Fits models PC2003, 32” thru 52”
6-3/8” OD X 7/8” HT, Overall cut commercial walk behinds.
height: 7-7/8”. (Top of pulley 3/4” ID for caster yoke shaft, 3/8” mounting holes.
nut to bottom of shaft). (Use with our 245-006 caster yoke)
H.D. diecast construction.
245-006 PT8670
D 22-13 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
JOHN DEERE continued JOHN DEERE continued
Part# O.E.M Application Part# O.E.M Application
D 22-14 D
DRIVE, RIDER & PUSHMOWER PART Banta
JOHN DEERE continued JOHN DEERE continued
Part# O.E.M Application Part# O.E.M Application
285-912 AM136733
Quill Assembly NEW
Fits L-100, L-110, L-120 and L-130
models with 42” and 48” decks.
Fits current Home Depot models. Quill / Spindle Assembly
For John Deere. (5/8 inch).
Fits model: 102, 105, 115,
285-908 GY20454 125, 135, 145, 155C, D100,
D110, D120, D130,D140,
D150, D160, LA100, LA105,
Quill Assembly LA110, LA115, LA120, LA125, LA130, LA135, LA140,
Fits John Deere 100 series riders LA145, LA155, LA165, X110, X120, X140, X125, X130R,
with 42”, 48” and 54” cut decks. X145, X155R, X165. (Uses a 5/8” blade retaining nut NOT
Fits blades with the 7 point star 1/2”). NOTE: For Quill / Spindle Assemblies using a 1/2”
centre holes. blade retaining nut see our 285-908.
Measures: 7-1/8” overall height
and 3.125” from deck mount to 285-913 TCA17517
bottom of spindle shaft. Top (pulley end)
Thread: 9/16”-18 and Bottom (blade end) Thread: 1/2”. NEW
(Uses our 230-029 bearing)
Quill / Spindle Assembly
For John Deere.
285-330 AM121229 Fits Zero Turn models:
Z520A, Z820A
(54” or 60” decks) and
Z850A (72” deck).
Quill Assembly
For John Deere 38” and
46” cut decks on 170, 175, 420-050 GY20495
180 and 185 series tractors. NEW
(Pulley NOT included).
NOTE: Same quill assembly as our
285-333 but without a pulley. Accepts pulleys with 18mm HEX ID.
Tractor Seat
Replacement Tractor seat to fit
285-909 GY20867 on John Deere Lawn & Garden
NEW GY21099 equipment. Fits John Deere
models: LA100, L100, L105,
L107, L108, L110, L111, X110,
102, 105, 125. Measures: 16.5”
Quill / Spindle Assembly
Overall Width X 18.25” Overall
For John Deere.
Seat Depth X 10.75” Overall
Fits model: G110,
Back Height. (4) 5/16-18 UNC RH
190C, LA150 and LA175.
Thread mount holes on 7.68 CC and 3.93” CC.
D 22-15 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
LAWN BOY LAWN BOY continued
Part# O.E.M Application Part# O.E.M Application
For Lawn Boy Control cables - see our 240-900 741316 / 32222
CONTROLS - THROTTLE & ACCESSORIES 18915 / 3003
1720859 / 35550
240-341 683129
240-614 700414
1054 / 118118
Oil Seal
Fits on Tillers, Double seal design,
Measures: 1” ID X 1-1/2” OD
240-291 607657
Drive Roller
Fits LH side - 2.4 MPH ground speed. Quill Assembly
Measures: 1/2” ID X 7/8” OD X 2-1/4” long Fits 38” cut decks.- side discharge, without pulley
(Uses with our 320-127 or 320-374 lawnmower blades
240-309 607658
285-502 742577 / 706623 / 741310 / 741311
Drive Roller 88213 / 88272 / 233214 / 241013
Fits RH side - 2.4 MPH ground speed.
Measures: 1/2” ID X 7/8” OD X 2-1/4” long
240-499 610441
611612
Drive Roller
Fits LH side - 3.1 MPH ground speed.
Measures: 1/2” ID X 1-1/8” OD X 2-1/4” long
240-481 610440
611611
Quill Assembly
Drive Roller
Fits 38” cut decks. - side discharge, without pulley
Fits RH side - 3.1 MPH ground speed.
(Uses with our 320-127 or 320-374 lawnmower blades)
Measures: 1/2” ID X 1-1/8” OD X 2-1/4” long
D 22-16 D
DRIVE, RIDER & PUSHMOWER PART Banta
MTD / CUB CADET / WHITE MTD / CUB CADET / WHITE
Part# O.E.M Application Part# O.E.M Application
D 22-17 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
MTD / CUB CADET / WHITE MTD / CUB CADET / WHITE
Part# O.E.M Application Part# O.E.M Application
285-736 618-04394
918-04394
D 22-18 D
DRIVE, RIDER & PUSHMOWER PART Banta
MTD / CUB CADET / WHITE MTD / CUB CADET / WHITE
Part# O.E.M Application Part# O.E.M Application
230-029 741-0919
Replacement Bearing
For our 225-052 or 285-189
285-110 717-0906
917-0906
Quill Assembly
Fits 44” cut deck, centre quill - use with double pulley also
fits 46” cut, left hand quill. For 800 thru 849 series “H”
decks. Shaft length: 6-3/8”, splined shaft
Uses our 230-029 replacement bearing.
Quill Assembly
Fits 38” and 42” decks. Model series 600 and 805, also 618-0117
42” models 700-739 and 750-769, - shaft length: 5-15/32”, 285-504
618-0112
- splined shaft. Uses our 230-029 replacement bearing. 918-0117
Part# 225-054 bearing housing only. MTD# 15296A - also fits our 285-
084 / 088
Quill Assembly
For 46” deck
- fits star hole blades
- LH spindle for 800 series
- includes: double pulley
Quill Assembly - 1996 and prior
Fits 44” cut deck, outer quill also fits 46” cut, both centre - includes: (1) 335-525 blade
and right hand quill. For 800 thru 849 series “H” decks. Uses our 230-029 spindle bearing
- shaft length: 4-7/8”, - splined shaft and 416-015 Jackshaft Nut
Uses our 230-029 replacement bearing.
D 22-19 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
MTD / CUB CADET / WHITE MTD / CUB CADET / WHITE
Part# O.E.M Application Part# O.E.M Application
Quill Assembly
Fits 46” decks. Fits star hole blades, RH & Centre S
pindle for 600 & 800 series, (3) for 600 series riders,
Quill Assembly 1997 to current, on 800 series tractors you require
Fits 46” decks. Fits star hole blades, RH and Centre. - (2) 285-508 + (1) 285-509 or (2) 285-515 + (1) 285-516
Spindle for 800 series, uses single pulley, 1993 thru 1996
(3) for 600 series riders(2) for 800 series riders 285-515 918-0240 / 618-0240 / 618-0430A
(or 285-508) 918-0430A / 112-0311
285-506 618-0138
618-0142
918-0142 / 918-0142A
Quill Assembly
Fits 46” decks. Fits star hole blades, LH Spindle for 800
series, 1997 to current
285-516 918-0241
(or 285-509) 618-0241
918-0431
Quill Assembly
For 46” deck
- fits star hole blades
- LH spindle for 800 series
Quill Assembly - includes: double pulley
Fits 38” and 42” decks. Fits star hole blades, - 1997 to current
without pulley, newest style “X” housing, 1998 to current - includes: (1) 335-455 blade
(416-015 “NUT” - fits 285-504 / 505 / 506 /508 / 509 Uses our 230-029 Spindle Bearing, Uses our 415-015
511 / 512 / 515 / 516 / 517 / 518 and 519) Jackshaft Nut, Uses our 285-891 Spindle Shaft
D 22-20 D
DRIVE, RIDER & PUSHMOWER PART Banta
MTD / CUB CADET / WHITE MTD / CUB CADET / WHITE
Part# O.E.M Application Part# O.E.M Application
D 22-21 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
MTD / CUB CADET / WHITE MTD / CUB CADET / WHITE
Part# O.E.M Application Part# O.E.M Application
Jackshaft
Fits models 390, 425-435, 460-495 NOTE: Same as our 285-022
& 875.For 1978 thru 1984 - 34”, 36” but includes bearings and spacer.
and 38” decks also 1976 thru 1985 (2) blade 30” decks. See our MTD heading for this quill / spindle assembly
Size: 4” L X 1-1/16” bearing surface length, 5/8”-11 UNC
thread, 3/8”-24 UNF internal thread. 285-017 ---------
285-018 ---------
Jackshaft Jackshaft
Fits our 285-505 Fits our 285-517
MTD Quill assembly. MTD Quill assembly.
Measures: 4-9/16” L Shaft OD: .785” Internal bolt thread: Measures: 4-7/8” L X .785” Shaft OD,
7/16”-20, Pulley nut thread: 5/8”-18 Fits later model 42” - 600 series.
Jackshaft
Fits our 285-504 and 285-884 Fits our
285-511 MTD Quill assemblies. 285-109
Measures: 5-1/2” L X .785” Shaft OD, 285-735
Internal bolt thread: 7/16”-20, Pulley nut thread: 5/8”-18 285-738
285-021 ---------
285-887 Fits our
Jackshaft 285-737
Fits our 285-506
and 285-509. MTD Quill Assemblies.
Measures: 5.975” L X .785” Shaft OD,
Blade nut thread and Pulley nut thread: 5/8”-18
285-890 Fits our
285-888 Fits our 285-519
285-506
D 22-22 D
DRIVE, RIDER & PUSHMOWER PART Banta
MTD / CUB CADET / WHITE MTD / CUB CADET / WHITE
Part# O.E.M Application Part# O.E.M Application
285-153 922-0153
Control Cable Description:
Deck Engagement Cable for MTD.
Engine Mount Bushing
Fits MTD 600 series riders.
Measures: 1/2” ID X 1-1/8” OD X 1/4” HT, Made of Nylon
For more Control Cables see our “Controls -
Throttle & Accessories
285-112 761-0168A
961-0168A 285-064 732-0433
761-0168B 932-0433
961-0168B Spring
Measures: 2-13/16” overall length,
Brake Assembly 1-5/8” coil length X 1/2” coil diameter
Fits 400 series shallow deck 38” cut. For 130 - 498 series
tractors. 1990 to current 600, 700 series riders. Measures: 285-056 732-0157
5-1/4” L, (2) .359” mounting holes, 1-1/8” CC Brake Return Spring
Measures: 3-3/8” overall length,
285-364 09322 1-15/16” coil length X 3/8” coil diameter
285-106 732-0153
Quill Brake Disc
For drive pulleys on 38” Deck Spring
and 42”. Model series 600, Measures: 9” overall length,
800, 805, 739, 750-769 4-3/4” coil length X 3/4” coil diameter
D 22-23 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
MTD / CUB CADET / WHITE MTD / CUB CADET / WHITE
Part# O.E.M Application Part# O.E.M Application
285-060 732-0429A
932-0429A Belt Guard
Shield for Quill Assemblies.
Extension Spring Used on 42” side discharge
Fits variable speed model 18 Hp Tractors. Speed selec- decks and deck “G”
tor lever spring. Measures: 4” overall length X 2-1/2” coil (Use with our 285-110 Quill Assembly)
length, Coil diameter: 1/2”
245-119 753-0674
285-062 732-0303
Drag Link Assembly
Clutch Spring Replaces MTD# 747-0899
Measures: 3-1/4” overall length on Riding mowers. 7/16”-20 threaded ends.
2-3/8” coil length X coil diameter: 3/8” Uses our 245-032 ball joint
245-089 923-0351
D 22-24 D
DRIVE, RIDER & PUSHMOWER PART Banta
MTD / CUB CADET / WHITE MTD / CUB CADET / WHITE
Part# O.E.M Application Part# O.E.M Application
240-194 713-0194
Drive Disc 713-0194-1
Fits MTD Snowblowers and 913-0194
Riders. Models 500, 510, 520
and 600, also found on
Sprocket Hub Assembly
John Deere Snowblowers - made by MTD.
For MTD. Used on large frame
Size: 6” OD X 1-1/8” ID (3) bolt hole pattern.
snowblowers (1975 thru 1997).
Measures: 5-1/2” OD (large gear) X
240-918 718-0494 1-3/4” OD (small gear),
32 tooth (large), 9 tooth (small), Bore: 3/4”.
NEW Includes (2) 225-110 brass bushings (MTD# 748-0184)
D 22-25 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
MTD / CUB CADET / WHITE MTD / CUB CADET / WHITE
Part# O.E.M Application Part# O.E.M Application
Linch Pin
Fits all two-stage Snowblowers models. Left Hand Handle Bracket
Size: Pin dia. 1/4”, Pin length: 1-3/4” under head. Fits self propelled mower
models 070-088, 260-265 and 280-282.
245-820 748-0278 Measures: 6-3/16” overall length X 1-5/8” wide.
Three 3/8” mounting holes.
Spacer
Use on drive belt on the pivot of
For MTD / Cub Cadet / White
lawn tractors, Hex OD: 7/8”, Control Cables, Throttle Controls
Length: .950” with a 5/16” diameter hole. etc please see our “CONTROLS
240-259 07120 - THROTTLE & ACCESSORIES”
section
Drive Roller
Measures: 5/8” ID X 1-5/8” OD, 255-208 711-0169
Length: 2-3/16” with 13 ribs. Made of plastic.
Clutch Collar
240-473 731-0393 Used to secure clutches to
03913 crankshafts and jackshafts.
(Priced & Sold individually)
Drive Roller Measures: 5/8” ID X 1” OD X 1/2” HT
Measures: 1/2” ID X 2-1/4” OD,
Length: 1-7/8” with 13 ribs. Made of plastic. 240-226 721-0100
D 22-26 D
DRIVE, RIDER & PUSHMOWER PART Banta
MURRAY / NOMA cont. MURRAY / NOMA cont.
Part# O.E.M Application Part# O.E.M Application
Spindle Bearing
Upper bearing for our
285-300 and 285-292 quills.
Measures: .625” ID X 1.575” OD X .475” HT
(Bearing# 6203-2DRS-LG-10 / 6203-2RS 5/8)
230-003 580781
99502H / MJ49562
Quill Assembly
Fits riding mower models
2001 and newer riders.For
42”, 46” and 52” deck on
new LT Rail Frame tractors.
Includes: housing, shaft,
bearings, grease fitting,
dust cover over one bearing.
Measures: 7-3/8” overall length X 6-7/8” OD Quill Assembly
9/16-18 UNF thread at each end of shaft. Centre quill for 45” cut double pulley, 1-3/8” centre to
(Uses our 405-204 blade adaptor) centre spacing on pulleys 2” blade saddle (Serviceable)
uses our 230-060 replacement bearing.
D 22-27 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
MURRAY / NOMA cont. MURRAY / NOMA cont.
Part# O.E.M Application Part# O.E.M Application
416-719 15X72
Lock Nut
Size: 1/2”-20 UNF thread,
2 way lock style. (Sold in multiples of 5)
Quill Assembly
Left hand quill for 45” cut 2” blade saddle (Serviceable)
Uses our 230-060 replacement bearing. 418-715 20062
Woodruff Key
285-305 1001709 Fits all vertical shaft engines to adapt
NEW 1001709MA clutch body and blade to shaft.
Size: 5/32” Thick X 5/8” Long. (Sold in multiples of 10)
D 22-28 D
DRIVE, RIDER & PUSHMOWER PART Banta
MURRAY / NOMA cont. MURRAY / NOMA cont.
Part# O.E.M Application Part# O.E.M Application
285-050 165X76
For NOMA Control Cables, Throttle
Deck Spring Controls etc., Please see
Lawn Tractor motion drive
idler return spring. our “CONTROLS - THROTTLE and
Fits 36”, 38”, 40” & 42” models 1989 to present. ACCESSORIES” section “20”.
Measures: 11-1/4” overall length,
4-1/4” coil length X 13/16” coil diameter. 21031 / 723-0156
245-027
723-3018
285-015 165X58
165X2 / 20682 Ball Joint
Blade drive Spring 3/8”-24 X 7/8” Right hand male thread,
Measures: 5” overall length, 3/8”-24 RH female thread.
3-1/2” coil length X 5/8” coil diameter.
245-019 50782
285-023 165X4 / 20684
Ball Joint
Blade drive Spring Male Thread: 5/16”-24
Measures: 5-3/4” overall length, right hand thread X
4-1/4” coil length X 3/4” coil diameter. Female Thread: 5/16”-24 right hand thread.
Measures: 1-7/16” long X 11/16” thread length
285-007 165X3 / 20683
245-116 91749 / 91749E700
Belt Idler Spring 91749F200
Measures: 6-3/16” overall length,
4-3/4” coil length X 3/4” coil diameter.
Drag Link Assembly
285-080 52636 For Tractors 1989 to current,
46359 36”, 38” and 40” cut.
Throw Out Spring Measures: 16-7/8” overall length X .606” diameter,
Measures: 6-1/2” overall length, Stud length: .650” X 3/8”-24 stud thread
3-5/8” coil length X 7/8” coil diameter.
285-775 91529SE
285-049 53886 21532
41074
Steering Disc
Throw Out Spring Fits Murray Garden Tractors.
Measures: 11-3/4” overall length, Size: 4-3/8” diameter X 5/16” Thick,
3-3/16” coil length X 3/4” coil diameter. (4) holes (While Quantities Last)
D 22-29 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
MURRAY / NOMA cont. MURRAY / NOMA cont.
Part# O.E.M Application Part# O.E.M Application
D 22-30 D
DRIVE, RIDER & PUSHMOWER PART Banta
MURRAY / NOMA cont. SCAG continued
Part# O.E.M Application Part# O.E.M Application
D 22-31 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
SCAG continued SIMPLICITY continued
Part# O.E.M Application Part# O.E.M Application
Blade Spacer
Fits Scag spindles.
SNAPPER
Size: 5/8” ID X 1” OD X 1/4” thick
285-201 5-2457
D 22-32 D
DRIVE, RIDER & PUSHMOWER PART Banta
SNAPPER continued SNAPPER continued
Part# O.E.M Application Part# O.E.M Application
Drive Disc
Fits Snapper 30” Estate walk 416-605 650607
behind mowers and Snowblowers.
Fits Snapper 4, 5 and 8 Hp snowblower
models: 4222, 5222, 5242, 7222, 7242 and 8264; also Flywheel Nut
found on some smaller Toro snowblowers. Measures: Fits steel cup
4-1/2” OD X 1” ID with (4) 1/4” bolt holes Small frame models.
240-275 1-0927
2-3364
7023364 For Tecumseh Starter Motors -
please see our
Drive Ring
For self propelled mowers “STARTER PARTS” section.
also 22” and 24” 2-stage snowblowers Also available for B & S,
Measures: 4” OD X 3” ID X 1/2” HT - Made of rubber Kawasaki, Kohler
D 22-33 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
TORO / WHEEL HORSE TORO / WHEEL HORSE
Part# O.E.M Application Part# O.E.M Application
Quill Assembly
Fits 46” decks. Fits star hole blades
Right Hand and Centre , Spindle for newer Toro
Quill Assembly models built by MTD, on 800 series tractors you require
Fits 52 Z models. Measures: 6-1/8” HT (top of pulley lip to (2) 285-508 + (1) 285-509 or, (2) 285-515 + (1) 285-516
bottom for shaft), Pulley diameter: 6-7/8” X 1” Blade
saddle: 2-1/2”. 285-738 112-0460
285-515 112-0311
Quill Assembly (or 285-508)
Fits 62 Z models. Center Quill / Spindle. Measures: 7-3/8”
HT (top of large pulley lip to bottom of shaft), Large pul-
ley diameter: 6-7/8” X 1.063” overall height, Small pulley
diameter: 5-1/2” X 3/4”, Blade saddle: 2-1/2”.
285-806 99-4640
Quill Assembly
For 46” deck, fits star hole blades.
Right Hand and Centre, Spindle for newer Toro
models built by MTD. Includes: (1) 335-455 blade
(3) for 600 series or (2) 285-515, (1) 285-516 for 800
series.Uses our 230-029 Spindle Bearing, Uses our
415-015, Jackshaft Nut. Uses our 285-889 Spindle Shaft
240-930 37-6570
Quill Assembly
Fits 62 Z models. Outer Quill / Spindle. Drive Disc
Measures: 4-1/2” HT (top of pulley lip to bottom for shaft), Measures: 4-1/2” OD X 1” ID with
Pulley diameter: 5-1/2” X 3/4”, Blade saddle: 2-1/2”. (4) 1/4” bolt holes.
D 22-34 D
DRIVE, RIDER & PUSHMOWER PART Banta
TORO / WHEEL HORSE TORO / WHEEL HORSE
Part# O.E.M Application Part# O.E.M Application
245-905 74-1841
260-147 51-4180
NEW 74-1851
Brake Drum
Fits Priline models. Front Pivot Arm Assembly
Measures: 5” OD X Fits Toro Commercial 21”
2-5/16” ID X 1-1/2” HT Heavy Duty Recycler - Rear bagger mowers. (Serial#
Centre to Centre: 2-3/4” 240000001 thru 240999999, 2004 on). Complete with
(Use with our 260-130 brake band) Zerk fitting.
D 22-35 D
Banta DRIVE, RIDER & PUSHMOWER PARTS
TORO / WHEEL HORSE
Part# O.E.M Application Part# O.E.M Application
Notes:
245-906 66-7560
NEW
245-907 66-7560
NEW
TROY BILT
240-900 1720859
Drive Disc
Fits models 42010, 42012,
42033, 42034, 42036, 42039,
42040, 42041 sel-propelled mowers;
42051 and 42052 snowblowers.
Measures: 6” OD X 5-3/8” ID with a 3” ID center.
285-387 1719762
Linch Pin
For Troy Bilt equipment.
Measures: 3/16” pin diameter X 1-1/4” pin length.
D 22-36 D