You are on page 1of 6

6.

Mezinárodní origami setkání - Blovice 2013


Česká ČOS
Czech
Králík / Rabbit
origami Origami
společnost Ronald Koh (Singapur / Singapore) Society

Rabbit (Ver. 1.3) cRonald Koh - 2011

This rabbit can be folded with ordinary origami paper. An 18cm square will result in a rabbit of approximately 7cm in
length. Start with the white side facing you.

1. 2.

Fold and unfold diagonally in both directions, ... ... then fold and unfold vertically and
horizontally.

3. 4.

Now fold and unfold between the dotted landmarks. Fold the top left corner to the dotted landmark.
Crease where the lines intersect only. Crease only where the new line intersects the top
edge of the paper.

5. 6.

Fold and unfold between the dotted landmarks again, Fold the top right corner through the dotted
and crease where the lines intersect. Turn the paper intersecting crease lines.
over.

112
6. Mezinárodní origami setkání - Blovice 2013
Česká ČOS
Czech
Králík / Rabbit
origami Origami
společnost Ronald Koh (Singapur / Singapore) Society

7. 8.

Now valley fold the top layer along the crease Turn the paper over.
line of the layer underneath.

9.
10.

6-7

Valley fold, then use the layers underneath Unfold to the position shown in
as guides to repeat Steps 6 and 7. Figure 11.

11. 13.

12.

Fold and unfold as illustrated, Fold and unfold again Fold and unfold at the
then turn the paper over twice more. top, and separate the
two layers at the bottom
by squash folding at
each side.

113
6. Mezinárodní origami setkání - Blovice 2013
Česká ČOS
Czech
Králík / Rabbit
origami Origami
společnost Ronald Koh (Singapur / Singapore) Society

14.
15.

16.

Valley fold at the top, and petal


fold and unfold below.

17

Open up the layers at the top as


illustrated, and squash fold at the bottom.
Valley fold each of the corners of
the triangle layer to the top, then
fold and unfold below as illustrated.

18. 19.

Valley fold the bottom corner to the dotted


reference point,crease firmly, and unfold.

20.

Now open up the layers at the Collapse as indicated.


bottom and restore the paper to
the position at the start of Step 16.
Petal fold.

21.
22.

23.

Valley fold to
the left, ...

Fold and unfold, ...

... then fold and unfold again,


as illustrated.

114
6. Mezinárodní origami setkání - Blovice 2013
Česká ČOS
Czech
Králík / Rabbit
origami Origami
společnost Ronald Koh (Singapur / Singapore) Society

24. 25. 26.

Rabbit’s ear along the crease lines Fold and unfold again. Using the crease line made Step
made in Step 22. 23, fold one lay to the right as
illustrated, ...

27. 28. 29. 30.

21 - 27

... like this. Continue as shown. Turn the paper over. Fold anf unfold yet Draw the horizontal edges
Repeat Steps 21 to 27 on again. towards the middle and valley
the left side. fold vertically in half, then unfold.

31. 32. 33.

... then vertically in half as


illustrated, Bringing the lower ... like this. Closed sink the flaps on the left
portion of the paper up an individually along the crease lines made in
angle, ... Step 29.

Valley fold 34. 34 35. 35 36. 36


horizontally, ...

Valley the corner. Repeat Valley fold to the right. Repeat Fold one layer down. Repeat
on the other side. on the other side. on the other side again.

115
6. Mezinárodní origami setkání - Blovice 2013
Česká ČOS
Czech
Králík / Rabbit
origami Origami
společnost Ronald Koh (Singapur / Singapore) Society

37. 37 38. 39. 40. 40

Swivel the head and ears with Crimp fold,... ... then draw out the Crimp fold on both sides.
valley folds on both sides on hidden layer from within
the neck. The relative positions the head
of the head and ears can be
varied in this way.

41. 41 42. 42 43.

Sink the sides of the head Mountain fold both sides of the Sink the corner at the throat
and the snout. head, and valley fold both sides and mountain fold the excess
of the snout. paper at tha snout within the
head.

44. 45.
45

Swivel as illustrated. The underlying layers can be bit of a bother. First


reverse fold the innermost layer between each hind
leg and the body as illustrated.

46. 47.
46

Next, mountain fold the next layer to get it out of


the way.
Reverse fold the corner on the right, and valley
fold to bring the left foreleg forward a little.

116
6. Mezinárodní origami setkání - Blovice 2013
Česká ČOS
Czech
Králík / Rabbit
origami Origami
společnost Ronald Koh (Singapur / Singapore) Society

48. 49.
48 47 - 48

Fold and unfold as illustrated. Repeat on the Repeat Steps 47 to 48 on the right foreleg,
other side. Draw out the hidden layer between varying the position as desired. Steps 50 onwards
the body and the foreleg. depict the right foreleg in an outreached position.
Unfold the corner from within the body.

51.
50.
50

Double inside reverse fold the hind leg and


Collapse as illustrated on both sides along existing outside reverse fold the base of the tail piece.
crease lines.

52. 52a 53.

51 - 52 53

52b

Mountain the excess edges on both sides of the Crimp one side of the right foreleg to form
hindleg under. Repeat Steps 51 and 52 on the a little paw. Separate the front layers of the
other hind leg. Figures 52a and 52b shows an ears and give the body some 3D shaping
enlarged view of the tail folds. and you are done.

Feed me ... ?

Copyright: Ronald Koh


Singapore With a little imagination and further
shaping, the rabbit can look like this.

117

You might also like