Professional Documents
Culture Documents
CAPACITIVE SENSORS
SENSORI CAPACITIVI
CAPACITIVE SENSORS
SENSORI INDUTTIVI E CAPACITIVI GENERAL SPECIFICATIONS OF INDUCTIVE
GENERALITÀ COMUNI - EN60947-5-2 AND CAPACITIVE SENSORS - EN60947-5-2
SUPERFICIE ATTIVA ACTIVE FACE
La superficie attiva di un sensore di prossimità induttivo è la superficie piana dalla The active face of proximity sensor is the surface from which emits an oscillating field
quale fuoriesce un campo di oscillazione entro il quale un oggetto metallico produce where a metallic object (inductive) or any material (capacitive) results in a change of
nel sensore un cambiamento di stato. Nei sensori capacitivi invece un materiale state of the sensor without entering in contact with it.
qualsiasi, anche non metallico, in vicinanza della superficie attiva genera delle
oscillazioni che producono nel sensore un cambiamento di stato. In ambedue i casi il
materiale azionatore non entra necessariamente
in contatto fisico col sensore. TS PS
EMBEDDABLE (FLUSH MOUNTING)
SENSORE TOTALMENTE SCHERMATO (TS) SENSORS (TS)
Il contenitore metallico copre lateralmente la The metal body covers the sensing area on all
superficie attiva del sensore e consente l’installa- sides allows the unit to be installed in metal parts
zione immersa in parti metalliche o il montaggio or next to other sensors without causing problems
affiancato di più sensori senza problemi di of reciprocal interference.
reciproca interferenza.
SENSORE PARZIALMENTE SCHERMATO (PS) NOT EMBEDDABLE (NON FLUSH MOUNTING) SENSORS (PS)
Il contenitore metallico lascia scoperta la parte laterale della superficie attiva del The metal body leaves uncovered part of the sensing area resulting in an increased
sensore e permette di ottenere a parità di diametro del sensore, una distanza di sensing distance. During installation it is important to remember the minimum
intervento maggiore rispetto a quella del tipo schermato. Nell’installazione è neces- distances from metallic parts in the case of inductive units and from any type of
sario quindi rispettare distanze minime da materiali metallici nel caso di sensori material in the case of capacitive units.
induttivi e nel caso di sensori capacitivi da qualsiasi tipo di materiale posto nelle It is not possible to mount more than one sensor side by side.
immediate vicinanze.
Non è possibile il montaggio affiancato di più sensori.
FATTORI DI RIDUZIONE NEI SENSORI INDUTTIVI E CAPACITIVI REDUCTION FACTORS IN INDUCTIVE AND CAPACITIVE SENSORS
Se l’oggetto da rilevare è costituito da metallo diverso da Fe360 (induttivi) o da If the object to be sensed is not Fe360 (inductives) or material other than metal
materiale diverso dal metallo (capacitivi) la distanza d’intervento diminuisce. (capacitives) the intervention distance reduces.
Inoltre se l’azionatore ha spessore e dimensioni inferiori a quelle indicate dalle Furthermore if the object to be sensed has dimensions and thickness less than those
norme, la distanza d’intervento si riduce ulteriormente. indicated then the intervention distance will be further reduced.
®
2
SENSORI INDUTTIVI E CAPACITIVI GENERAL SPECIFICATIONS OF INDUCTIVE
GENERALITÀ COMUNI - EN60947-5-2 AND CAPACITIVE SENSORS - EN60947-5-2
•Nell’installazione di sensori con ghiere di fissaggio non serrarle eccessivamente • When installing sensor using locknuts do not overtighten them in order to avoid
onde evitare il danneggiamento dell’involucro del sensore e la conseguente rottura damage to the body of the sensor and the internal circuit. Particular attention should
del circuito posto all’interno. be given to sensors with a diameter equal to or less than 12 mm. Attention should
Particolare attenzione va posta nei modelli di diametro uguale o inferiore ai 12 mm. all be given to avoid the installation of a sensor into a hole with the same diameter
Porre uguale attenzione nell’avvitare un sensore filettato in un foro dello stesso
as this may cause irreparable damage.
filetto in quanto eventuali forzature potrebbero danneggiarlo irreparabilmente.
• When preparing threaded holes for the fixing of sensors the following diameters
•Per la preparazione dei fori filettati per l’alloggiamento dei sensori, attenersi ai
seguenti diametri di foratura in mm: should be followed:
M8 x 1 = ø7 • M12 x 1 = ø11 • M18 x 1 = ø17 • M30 x 1.5 = ø28.4 M8 x 1 = ø7 o M12 x 1 = ø11 o M18 x 1 = ø17 o M30 x 1.5 = ø28.4
SPECIFICHE DI COLLEGAMENTO IN SERIE E PARALLELO CONNECTION FOR INDUCTIVE AND CAPACITIVE SENSORS
ALIMENTAZIONE IN C.C. - COLLEGAMENTO IN SERIE (AND) CONNECTION OF D.C. TYPES IN SERIES (AND LOGIC)
I sensori connessi in questo modo abilitano una sola uscita quando sono eccitati In some applications it is necessary to obtain two corresponding signals before an action
contemporaneamente. is carried out. Two sensors connected
Nel realizzare questo tipo di colle- in this way will activate one output
PROX PROX PROX PROX PROX PROX
gamento, per i modelli in corrente when they are excited simultaneously.
continua, considerare quanto segue: NPN NPN NPN PNP PNP PNP When D.C. amplified types are used it
BLU / BLUE
NERO / BLACK
MARRONE / BROWN
BLU / BLUE
NERO / BLACK
MARRONE / BROWN
BLU / BLUE
NERO / BLACK
MARRONE / BROWN
MARRONE / BROWN
NERO / BLACK
BLU / BLUE
ALIMENTAZIONE IN C.C. COLLEGAMENTO IN PARALLELO (OR) CONNECTION OF D.C. TYPES IN PARALLEL (OR LOGIC)
In questo tipo di connessione i sensori possono abilitare indipendentemente, se Connected in this way all sensors can activate the common output independently
eccitati, l’uscita comune. when excited.
Nei modelli amplificati in corrente When amplified D.C. types are used
continua tenere presente che ogni PROX PROX PROX PROX PROX PROX it is necessary to take into account
sensore interessato viene caricato NPN NPN NPN PNP PNP PNP that each sensor has as an addition-
con le resistenze interne degli altri al load of the resistance of the other
BLU / BLUE
NERO / BLACK
MARRONE / BROWN
BLU / BLUE
NERO / BLACK
MARRONE / BROWN
BLU / BLUE
NERO / BLACK
MARRONE / BROWN
MARRONE / BROWN
NERO / BLACK
BLU / BLUE
MARRONE / BROWN
NERO / BLACK
BLU / BLUE
MARRONE / BROWN
NERO / BLACK
BLU / BLUE
ALIMENTAZIONE IN C.A. COLLEGAMENTI IN SERIE E PARALLELO CONNECTION OF A.C. TYPES IN SERIES OR IN PARALLEL
La “caduta di tensione” e “la corrente residua” sono parametri fondamentali nel caso A.C. sensors can be connected in series taking into account the voltage drop (≤ 6V)
di collegamenti di uno o più sensori. I sensori in corrente alternata possono essere col- present in the sensor when connected in parallel. The off load current (≤ 4mA)
legati in serie tenendo conto che la caduta di tensione (<6V) ai capi del sensore viene should be summed and attention should be given when in the minimum load con-
moltiplicata per il numero di sensori utilizzati. Nel collegamento in parallelo occorre dition (high load impedance).
considerare che la corrente residua di ogni sensore si somma, pertanto è importante Such connections should in any case not be done as a function anomalous to
considerare la corrente residua totale, specialmente nel caso di collegamenti a circui- the sensor can be generated. The "voltage drop" and the "residual current" is
ti ad alta impedenza e relè a basso assorbimento. Tali collegamenti sono comunque important in this type of connection.
sconsigliati perchè possono generare un funzionamento anomalo dei sensori stessi.
ALIMENTAZIONE A 24V IN C.A. - AVVERTENZE 24V A.C. POWER SUPPLY - WARNING
Nei sensori con alimentazione a 24Vca tenere conto della caduta di tensione (<6V) In sensors supplied with 24V A.C. the voltage drop (≤ 6V) existing in the sensor and
presente ai capi del sensore e della caduta eventuale sui cavi di collegamento tra il the possibile voltage drop due to the connecting wires between the sensor and the
sensore ed il carico. Per ottenere una tensione adeguata sul carico si consiglia di load should be taken into account. In order to maintain an adequate voltage it is
aumentare la tensione di alimentazione almeno di 6V. reccomended that the supply voltage be increased by at least 6V.
®
4
SENSORI DI PROSSIMITÀ CAPACITIVI PROXIMITY CAPACITIVE SENSORS
SERIE SC SC SERIES
PRINCIPIO DI FUNZIONAMENTO WORKING PRINCIPLE
I sensori di prossimità capacitivi contengono un Capacitive sensors contain an oscillator transistor
oscillatore a transistor situato nella parte ante- in the front section. The oscillating circuit R-C
riore. Il circuito oscillante R-C (resistenza-con- (resistor-capacititor) is influenced by variations
densatore) viene influenzato dalla variazione di in capacity in fact when any material, solid or
capacità, infatti quando un materiale qualsiasi liquid (water, wood, metals, coffee, powders,
solido o liquido (acqua, vetro, legno, metallo, etc.) come into contact with the active surface
caffé, polveri, ecc.) interessa la superficie attiva of the sensor the capacitance increases putting
del sensore, la capacità aumenta mettendo in into action the oscillator up until the threshold of
azione l’oscillatore fino ad invertire la soglia del trigger inverts. By introducing a change in the
trigger, inducendo un cambiamento di condizione condition of the final stage and therefore in the
dello stadio finale ed il conseguente comando di command of the external load a potentiometer
un carico esterno. Un potenziometro permette la makes fine adjustements to the switching
regolazione fine della distanza di intervento. Tutti distance. All the sensors are protected against a
i sensori sono protetti alle inversioni di polarità, change of polarity and electrical disturbances of
a disturbi elettrici di origine induttiva e sono forniti inductive origin, and they are protected against
con protezione al corto circuito permanente del short circuits.
carico. Possono essere forniti ad intervento rapido They can be supplied with rapid or delayed
o temporizzato. Le parti plastiche dei sensori switching. The plastic parts of the capacitive
capacitivi (custodie, tappi, codoli e ghiere) sono sensors (body, plugs, oulets and locknuts) are
realizzate in Makrolon, materiale plastico atossico, made of makrolon which is not toxic, non static
antistatico e resistente all’abrasione. and resistant to abrasives.
SCELTA DI UN SENSORE CAPACITIVO SCHEMA A BLOCCHI DI SENSORE AMPLIFICATO CHOICE OF A CAPACITIVE SENSOR
Nella scelta di un sensore capacitivo si deve BLOCK DIAGRAM OF AMPLIFIED CAPACITIVE SENSOR When choosing a capacitive sensor the final use
tenere presente l’utilizzo finale, cioé il materiale should be kept in mind, that is the material to be
da controllare, la sua forma e la composizione. controlled, its form and composition.
Si deve porre molta attenzione ai fattori di ridu- The reduction factors related to every material
zione dei vari materiali e della loro massa fisica. should be remembered and also their physical
È comunque consigliabile nell’uso dei sensori mass.
capacitivi, se le circostanze lo consentono, l’uti- If possible it is recommended to use not em-
lizzo dei modelli parzialmente schermati cioé beddable model, that is not mounted flush with
non montabili a filo metallo perché si può contare the surface as it is possible to take advantage of
su un’ampiezza di capo sensibile molto superiore e la sensibilità non necessita di essere the much greater sensitive field, this means that the sensor need not be set to the maxi-
spinta all’eccesso causando a volte eccitazioni non volute a causa di variazioni di tempera- mum where it would be more prone to effects from temperature variations, humidity,
tura, umidità, depositi di polvere ecc. Se invece l’installazione consente solo l’utilizzo di powder deposits, etc.
sensori totalmente schermati, per montaggio a filo metallo, accertarsi che la sensibilità If it is necessary to install the sensor flush with the surface it is advised to make a setting
occorrente per il buon funzionamento non sia molto spinta. La differenza sostanziale tra i which is not too close to the maximum.
due modelli è che a parità di distanza di intervento tra un sensore totalmente ed uno The main difference between the totally screened and partially screened types of sensors
parzialmente schermato, il primo necessita di una sensibilità all’incirca doppia del secondo is that at equal intervention distances the former requires a sensitivity of about the double
per funzionare e quindi lavora in condizioni più critiche. of the latter and therefore functions under more critical conditions.
APPLICAZIONI APPLICATIONS
I sensori capacitivi trovano largo impiego nelle applicazioni dove il materiale da controllare Capacitive sensors are used widely as limit switches which are sensitive to all types of
non è necessariamente metallo. Sono ampiamente utilizzati come controlli di livello minimo materials, as limit controls for sensing the maximum and minimum levels of liquids,
e massimo di liquidi, prodotti in polvere, granulari ecc. oppure per conteggio o rilevazione powders, granules, etc. in silos and various containers. They can also be used for sensing
di pezzi metallici e non metallici. or counting metallic and non metallic objects.
CAVO
SC30
SC30SP-SC30SM CAVO / ATTACCO H
SC30P-RE25T SC40P CABLE
SC4 SC40P-T
CABLE / H PLUG CAVO / CABLE
CAVO ATTACCO
B
CABLE H M12
H PLUG
mPm
M12
REG. SENSIBILITÀ
LED LED SENSITIVITY ADJ.
SC18SP / SC18SM SC18SP-H / SC18SM-H SC30P-K / SC30M-K
®
62
SENSORI DI PROSSIMITÀ CAPACITIVI PROXIMITY CAPACITIVE SENSORS
SERIE SC SC SERIES
MODELLI AD INTERVENTO TEMPORIZZATO SENSORE TEMPORIZZATO SC40P-AE35T CARICO DELAYED MODELS
Sono sensori capacitivi che forniscono il segnale These are capacitive sensors which give an
DELAYED SENSOR SC40P-AE35T LOADING
di uscita al carico esterno con una temporizza- output signal to the load which can have an
zione regolabile fino a 15 min. alla eccitazione o REG. TEMPO adjustable time delay up to 15 min. To its
alla diseccitazione con funzioni N.O. oppure N.C. TIME ADJUST. energization and deenergization switching in
Vengono forniti esclusivamente nel modello REG. SENSIBILITÀ
both N.O. and N.C. types. They are supplied
diam. 40 mm. ed in corrente alternata. Le gamme SENSITIVITY ADJ. only in the Ø 40 mm model A.C.
di temporizzazione disponibili sono le seguenti: LED The available ranges of delay are the following:
NORME DA RISPETTARE PER UNA CORRETTA INSTALLAZIONE INSTRUCTIONS FOR CORRECT INSTALLATION
TOTALMENTE SCHERMATI / EMBEDDABLE PARZIALMENTE SCHERMATI / NOT EMBEDDABLE
D D/2 D D 2D D D D D
®
63
SENSORI DI PROSSIMITÀ CAPACITIVI PROXIMITY CAPACITIVE SENSORS
SERIE SC SC SERIES
SENSORI IN ESECUZIONE C PER CORRENTE CONTINUA (4 FILI) SENSORS VERSION C FOR DIRECT VOLTAGE (4 WIRES)
Sono sensori amplificati in corrente continua che oltre all’oscillatore hanno incorporato These are amplified D.C. sensors which contain an output amplifier in addition to the
anche l’amplificatore di uscita. Vengono forniti a 4 fili con funzione antivalente nelle versioni oscillator. They are supplied as 4 wires with antiphase outputs in the types NPN and PNP.
NPN o PNP. In questa esecuzione i sensori presentano come caratteristiche standard la As standard, this version of sensor is protected against short circuit, absolutely protected
protezione contro il corto circuito permanente del carico, sicurezza assoluta contro l’inver- against polarity inversion and current peaks created by the disconnection of inductive
sione di polarità e protezione ai picchi prodotti dal disinserimento dei carichi induttivi. loads. These sensors can be supplied with power supplies: ALNC - ALTP.
Possono essere forniti in abbinamento agli alimentatori mod. ALNC - ALTP. They are adapted for inputs of programmable controllers.
Sono compatibili con ingressi di controllori programmabili.
SENSORI IN ESECUZIONE A PER CORRENTE ALTERNATA E CONTINUA (2 FILI) SENSORS VERSION A FOR ALTERNATING OR DIRECT VOLTAGE (2 WIRES)
Sono sensori amplificati a due fili in grado di funzionare sia con tensioni alternate che These are amplified sensors with two wires which function both in A.C. and D.C., these
continue. Questi dispositivi oltre all’oscillatore, hanno incorporato anche un amplificatore di products as well as having an oscillator have a mosfet output amplifier incorporated which
uscita a Mosfet, in grado di aprire e chiudere un carico molto velocemente. is able to open and close a load very quickly.
Il carico, essendo collegato in serie al sensore, viene attraversato dalla stessa corrente The load which is connected in series with the sensor is passed through by the same
residua che lo alimenta. In particolare è necessario prestare molta attenzione ai relè a residual current that it is supplied by. It is particularly important to pay attention to the low
basso consumo. Infatti bisogna accertarsi che: consumption relay, in fact it is important to ensure that:
- la corrente richiesta per la sicura eccitazione del relè sia UGUALE o SUPERIORE alla - the required current for the switching of the relay is EQUAL to or SUPERIOR to the
“corrente minima di uscita” richiesta dal sensore; minimum output current required by the sensor;
- la corrente richiesta per la sicura diseccitazione del relè sia SUPERIORE alla “corrente - the current required of the secure releasing of the relay is SUPERIOR to the residual
residua” del sensore. current of the sensor.
Non rispettando questi accorgimenti si otterrà una commutazione incerta del relè. If these parameters are not respected there will be an uncertain switching of the relay.
Inoltre è opportuno prestare attenzione ai collegamenti ad ingressi ad alta impedenza dei Furthermore attention must be given to high impedance input connections of electronic
comandi elettronici, in quanto la corrente residua del sensore potrebbe essere sufficiente commands as the residual current in the sensor could be sufficient to cause activation.
ad attivarli. In the closed state a voltage drop can be found this should be taken into account especially
Nello stato di chiusura si verifica invece ai capi del sensore una caduta di tensione che when there is a low voltage supply.
deve essere considerata soprattutto nel caso di basse tensioni di alimentazione. All AC/DC capacitive sensors are short circuit protected (up to 50 Vdc and 250 Vac).
Tutti i sensori capacitivi CA/CC sono protetti al cortocircuito (fino a 50 Vcc e 250 Vca). They are also protected against voltage transients coming from the power supply or
Sono inoltre dotati di una efficace protezione ai transitori di tensione provenienti dalla rete generated by the load. They are compatible with P.L.C. units.
o generati dal carico. Sono compatibili con ingressi di controllori programmabili.
SENSORI IN ESECUZIONE R CON relè (5 FILI) SENSORS VERSION R WITH RELAY (5 WIRES)
Sono sensori amplificati in grado di funzionare sia con tensioni alternate che continue. These are amplified sensors which can operate with both AC and DC power supplies.
Questi dispositivi, oltre all’oscillatore e all’amplificatore, hanno incorporato anche un relè The sensors as well as the oscillator and amplifier have incorporated a relay which
che fornisce un contatto di uscita in scambio da 1A a 220Vca. provides one changeover output contact from 1Amp. at 220 Vac.
Il carico esterno può essere collegato al contatto NO oppure NC del relè suddetto; tale The external load can be connected to the NO or NC contact of the relay, this solution
soluzione garantisce una maggior sicurezza in presenza di carichi elevati (fino a 1A) a guarantees greater security in the presence of high loads (up to 1A) which is different to
differenza dei sensori ad uscita statica. sensors with output.
Sono disponibili modelli ad intervento istantaneo (pag. 71) o temporizzato con funzioni Types with instantaneous intervention are available (page 71) or delayed with program-
programmabili (pag. 74). mable functions (page 74).
YELLOW/GREEN
BIANCO/WHITE
BLU/BLUE MARRONE/BROWN
PNP NO+NC -- NC
ALIMENTAZIONE DI SENSORI CAPACITIVI IN CORRENTE CONTINUA SUGGESTION FOR SUPPLYING VOLTAGE TO CAPACITIVE SENSORS
ESEMPIO A / EXAMPLE A ESEMPIO B / EXAMPLE B
Stabilizzatore/Voltage stabilizer
CA
Vac Vac
Vca CA
Vac Vac
Vca
50-60 Hz
50-60 50-60 Hz
50-60 Hz
C Vcc
Vdc C Vdc
Vcc
La tensione di alimentazione deve essere adeguata alle caratteristiche dei dispositivi usati. The supply voltage should be adjusted according to the characteristics of the sensor used. It is
Usare sempre trasformatori con tensione di secondario Vca inferiore alla tensione continua recommended to use a trasformer with secondary voltage Vac lower than the direct voltage Vdc
desiderata Vcc. La tensione Vca di secondario da utilizzare si ricava così: required. The secondary voltage Vac is found as follows:
Vca = (Vcc + 1) : 1,41 Vac = (Vdc + 1) : 1,41
Inoltre la tensione continua Vcc di alimentazione dei dispositivi deve essere filtrata con una The supply voltage Vdc of the sensor should be filtered with a capacity C at least 470 µF for each
capacità C di almeno 470 µF per ogni 200 mA prelevati dall’alimentatore. 200 mA used.
Se la tensione continua a disposizione è elevata utilizzare esclusivamente lo schema B con un If the supply voltage Vdc is high it is recommended to follow the diagram B with a proper
adeguato stabilizzatore di tensione. voltage stabilizer.
®
64
SENSORI CAPACITIVI CAPACITIVE SENSORS
ESEMPI DI APPLICAZIONE APPLICATION EXAMPLES
CONTROLLO DI LIVELLO A CONTATTO CONTROLLO DI LIVELLO ATTRAVERSO CONTROLLO DI LIVELLO IN SERBATOI METALLICI
DI MATERIALI SOLIDI O LIQUIDI SERBATOI NON METALLICI ATTRAVERSO FINESTRELLA IN VETRO O PLASTICA
CONTACT LEVEL CONTROL LEVEL CONTROL FOR NON LEVEL CONTROL FOR METAL CONTAINERS
FOR SOLIDS OR LIQUIDS METALLIC CONTAINERS USING PLASTIC OR GLASS WINDOWS
RE
CA
H
IT E
W L
LE AGI
ND FR
HA
TUBAZIONE
NON METALLICA
NON METALLIC CONTROLLO DI
TUBING FLUSSO DI FLUIDI
LIQUID FLOW
CONTROL CONTROLLO PRESENZA,
CONTEGGIO E SMISTAMENTO
AUTOMATICO DI PEZZI
METALLICI E NON METALLICI
AUTOMATIC PRESENCE
CARICO MATERIALE / LOADING COUNTING AND SORTING
CONTROL OF METALLIC
AND NON METALLIC ARTICLES
+250 °C
TEMPO MAX. DI SCARICO 15 MIN.
0 °C
ALSC
–200 °C
®
65
SENSORI CAPACITIVI M18 x 1 • CAPACITIVE SENSORS M18 x 1
• CUSTODIA CILINDRICA PLASTICA O METALLICA • MODELLI 4 FILI IN C.C. - ESECUZIONE-C
• CYLINDRICAL HOUSING PLASTIC OR METALLIC • 4 WIRES D.C. MODELS - VERSION-C
62 55
REG. SENSIBILITÀ REG. SENSIBILITÀ
SENSITIVITY ADJ.
TOTALMENTE SCHERMATI SENSITIVITY ADJ.
SC18SP - C5 NPN NO + NC SC18SM - C5 NPN NO + NC SC18SP - CE10 NPN NO + NC SC18SM - CE10 NPN NO + NC
MODELLI CON CAVO C18000048 C18000055 C18000061 C18000067
MODELS WITH CABLE SC18SP - C5 PNP NO + NC SC18SM - C5 PNP NO + NC SC18SP - CE10 PNP NO + NC SC18SM - CE10 PNP NO + NC
C18000045 C18000052 C18000058 C18000064
SC18SP - C5 NPN NO + NC H SC18SM - C5 NPN NO + NC H SC18SP - CE10 NPN NO + NC H SC18SM - CE10 NPN NO + NC H
MODELLI CON CONNETTORE C18000072 C18000073 C18000076 C18000077
MODELS WITH CONNECTOR SC18SP - C5 PNP NO + NC H SC18SM - C5 PNP NO + NC H SC18SP - CE10 PNP NO + NC H SC18SM - CE10 PNP NO + NC H
C18000070 C18000071 C18000074 C18000075
®
66
SENSORI CAPACITIVI M18 x 1 • CAPACITIVE SENSORS M18 x 1
• CUSTODIA CILINDRICA PLASTICA O METALLICA • MODELLI 2 FILI IN C.A. - ESECUZIONE-A
• CYLINDRICAL HOUSING PLASTIC OR METALLIC • 2 WIRES A.C. MODELS - VERSION-A
62 55
REG. SENSIBILITÀ REG. SENSIBILITÀ
SENSITIVITY ADJ. SENSITIVITY ADJ.
CAVO CAVO
CABLE CABLE
LED LED
90.5 7.5 83
62 55
REG. SENSIBILITÀ REG. SENSIBILITÀ
SENSITIVITY ADJ. SENSITIVITY ADJ.
ATTACCO ATTACCO
H M12 H M12
H PLUG H PLUG
M12 M12
LED LED
95.5 7.5 88
0÷5 0 ÷ 10
20 ÷ 250 (Valori massimi assoluti ripple incluso / absolute maximum ratings ripple included)
≤ 20
10
< 10
300
1.5
≤1
<6
Presente
Incorporated
Presente
Incorporated
-20 ÷ +70
67
3 x 0.35 mm2
Attacco H (M12) - Vedi pag. 63 - fig. 2 / H Plug (M12) - See page 63 - pict. 2
®
67
SENSORI CAPACITIVI M30 x 1,5 • CAPACITIVE SENSORS M30 x 1,5
• CUSTODIA CILINDRICA PLASTICA O METALLICA • MODELLI 4 FILI IN C.C. - ESECUZIONE-C
• CYLINDRICAL HOUSING PLASTIC OR METALLIC • 4 WIRES D.C. MODELS - VERSION-C
1 55 16 15 41 16
REG. SENSIBILITÀ REG. SENSIBILITÀ
SENSITIVITY ADJ. SENSITIVITY ADJ.
PARZIALMENTE SCHERMATI 78 78
CARATTERISTICHE TECNICHE
TECHNICAL CHARACTERISTICS LED
ATTACCO
LED
ATTACCO
H M12 H M12
H PLUG H PLUG
M12 M12
Dimensioni / Dimensions mm 84 84
SC30SP - C20 NPN NO + NC SC30SM - C20 NPN NO + NC SC30SP - CE25 NPN NO + NC SC30SM - CE25 NPN NO + NC
MODELLI CON CAVO C30000030 C30000040 C30000050 C30000060
MODELS WITH CABLE SC30SP - C20 PNP NO + NC SC30SM - C20 PNP NO + NC SC30SP - CE25 PNP NO + NC SC30SM - CE25 PNP NO + NC
C30000016 C30000035 C30000045 C30000055
SC30SP - C20 NPN NO + NC H SC30SM - C20 NPN NO + NC H SC30SP - CE25 NPN NO + NC H SC30SM - CE25 NPN NO + NC H
MODELLI CON CONNETTORE C30000020 C30000021 C30000024 C30000025
MODELS WITH CONNECTOR SC30SP - C20 PNP NO + NC H SC30SM - C20 PNP NO + NC H SC30SP - CE25 PNP NO + NC H SC30SM - CE25 PNP NO + NC H
C30000017 C30000019 C30000022 C30000023
Isteresi
Hysteresis % Sn ≤ 20
Frequenza max di lavoro
Switching frequency Hz 10
Ripetibilità (a temperatura costante)
Repeatability (at constant temperature) % Sn < 10
Corrente max di uscita 200
Max output current mA
Assorbimento a 24Vcc ≤ 10
Absorption at 24Vdc mA
Corrente residua
Residual current mA
Muffola di protezione
Protection housing Montaggio possibile / Possible mounting
®
68
SENSORI CAPACITIVI M30 x 1,5 • CAPACITIVE SENSORS M30 x 1,5
• CUSTODIA CILINDRICA PLASTICA O METALLICA • MODELLI 2 FILI IN C.A./C.C. - ESECUZIONE-A
• CYLINDRICAL HOUSING PLASTIC OR METALLIC • 2 WIRES A.C./D.C. MODELS - VERSION-A
1 55 16 1 55 16 15 41 16 15 41 16
REG. SENSIBILITÀ REG. SENSIBILITÀ REG. SENSIBILITÀ REG. SENSIBILITÀ
SENSITIVITY ADJ. SENSITIVITY ADJ. SENSITIVITY ADJ. SENSITIVITY ADJ.
78 84 78 84
0 ÷ 20 0 ÷ 25
20 ÷ 250 (Valori massimi assoluti ripple incluso / absolute maximum ratings ripple included)
≤ 20
10
< 10
300
1.5
≤2
≤4
Presente
Incorporated
Presente
Incorporated
-20 ÷ +70
67
3 x 0.35 mm2
Attacco H (M12) - Vedi pag. 63 - fig. 2 / H Plug (M12) - See page 63 - pict. 2
®
69
SENSORI CAPACITIVI M30 x 1,5 • CAPACITIVE SENSORS M30 x 1,5
• CUSTODIA CILINDRICA PLASTICA O METALLICA • MODELLI 4 FILI IN C.C. - ESECUZIONE-C
• CYLINDRICAL HOUSING PLASTIC OR METALLIC • 4 WIRES D.C. MODELS - VERSION-C
TOTALMENTE SCHERMATI
EMBEDDABLE (FLUSH MOUNTING)
PARZIALMENTE SCHERMATI
NOT EMBEDDABLE (NON FLUSH MOUNTING) 77 18 72 18 65 20
LED LED LED
CARATTERISTICHE TECNICHE
TECHNICAL CHARACTERISTICS REG. SENSIBILITÀ REG. SENSIBILITÀ REG. SENSIBILITÀ
SENSITIVITY ADJ. SENSITIVITY ADJ. SENSITIVITY ADJ.
95 15 90 20 85
Dimensioni / Dimensions mm
SC30M - C20 NPN NO+NC K SC30M - CE25 NPN NO+NC K SC30P - CE25 NPN NO+NC K
MODELLI CON CONNETTORE K CAP000031 CAP000032 CAP000033
MODELS WITH K CONNECTOR SC30M - C20 PNP NO+NC K SC30M - CE25 PNP NO+NC K SC30P - CE25 PNP NO+NC K
CAP000040 CAP000041 CAP000042
Corrente residua
Residual current mA
Caduta di tensione (uscita attivata)
Voltage drop (sensor ON) V < 1.8
Protezione al corto circuito Presente
Short circuit protection Incorporated
Led visualizzatore Presente
Led Incorporated
Limiti di temperatura
Temperature limits °C -20 ÷ +70
Grado di protezione
IP rating IP 65
Custodia Ottone nichelato Ottone nichelato Plastica
Housing Nickelled brass Nickelled brass Plastic
Cavo PVC
PVC Cable 3m 4 x 0.25 mm2
Muffola di protezione
Protection housing Montaggio possibile / Possible mounting (SCM-K)
Schemi di collegamento Vedi pag. 64 - fig. 5 / See page 64 - pict. 5
Wiring diagrams
Collegamento con connettore K - Vedi pag. 63 - fig. 3 / K - See page 63 - pict. 3
Connection with connector
Norme per installazione
Instructions for installation Vedi pag. 63 / See page 63
®
70
SENSORI CAPACITIVI M30 x 1,5 • CAPACITIVE SENSORS M30 x 1,5
• CUSTODIA CILINDRICA PLASTICA O METALLICA • MODELLI 2 FILI IN C.A./C.C. - ESECUZIONE-A • CUSTODIA PLASTICA / USCITA A RELÈ
• CYLINDRICAL HOUSING PLASTIC OR METALLIC • 2 WIRES A.C./D.C. MODELS - VERSION-A IN SCAMBIO / ESECUZIONE-R
• HOUSING PLASTIC / RELAY OUTPUT
CHANGEOVER / VERSION-R
77 18 72 18 65 20 73 REG. SENSIBILITÀ
SENSITIVITY ADJ.
LED LED LED
LED
SC30M - A20 NO/NC K SC30M - AE25 NO/NC K SC30P - AE25 NO/NC K SC30P - RE25
CAP000024 CAP000023 CAP000025 C30000011
NO/NC PROGRAMMABILE NO/NC PROGRAMMABILE NO/NC PROGRAMMABILE USCITA RELÈ IN SCAMBIO
NO/NC PROGRAMMABLE NO/NC PROGRAMMABLE NO/NC PROGRAMMABLE RELAY CHANGEOVER
0 ÷ 20 0 ÷ 25 0 ÷ 25 0 ÷ 25
20 ÷ 250 12 ÷ 50
20 ÷ 250 12 ÷ 240
≤ 20 ≤ 20
10 10
< 10 < 10
1.5
≤2
<6
65 67
Montaggio possibile
Montaggio possibile / Possible mounting (SCM-K) Possible mounting (SCM-P)
Vedi pag. 64 - fig. 6 / See page 64 - pict. 6 Vedi pag. 64 - fig. 7 / See page 64 - pict. 7
®
71
SENSORI CAPACITIVI M40 x 1,5 • CAPACITIVE SENSORS M40 x 1,5
• CUSTODIA CILINDRICA PLASTICA • MODELLI 2 FILI IN C.A./C.C. - ESECUZIONE-A - INTERVENTO ISTANTANEO O TEMPORIZZATO
• CYLINDRICAL HOUSING PLASTIC • 2 WIRES A.C./D.C. MODELS - VERSION-A - STANDARD AND DELAYED MODELS
PARZIALMENTE SCHERMATI
NOT EMBEDDABLE (NON FLUSH MOUNTING)
72 Vista posteriore modello temporizzato
LED Back view delayed model *Identificare il n° 100 della scala
REG. SENSIBILITÀ
REG. TEMPO* del trimmer di regolazione
SENSITIVITY ADJ. REG. SENSIBILITÀ LED TIME ADJ.* tempo con il fondo scala della
SENSITIVITY ADJ.
1 - 15 min. gamma di temporizzazione.
CARATTERISTICHE TECNICHE 50
Grado di protezione IP 67 65
IP rating
Cavo PVC 2m 3 x 0.50 2 x 0.50
PVC Cable
Funzioni temporizzate Vedi pag. 63 / See page 63
Delayed functions
Schemi di collegamento
Wiring diagrams Vedi pag. 64 - fig. 6 / See page 64 - pict. 6
Norme per installazione Vedi pag. 63 / See page 63
Instructions for installation
®
72
SENSORI CAPACITIVI ALTA TEMPERATURA SC18M-HT/SC30M-HT
HIGH TEMPERATURE CAPACITIVE SENSORS SC18M-HT/SC30M-HT MODELS
GENERALITÀ GENERAL DETAILS
I sensori capacitivi per alta temperatura sono da conside- The high temperature sensors should be considered
rarsi appartenenti alla famiglia dei sensori capacitivi as part of the traditional range of sensors with the dif-
tradizionali, con la sola differenza che la parte elettronica ference that electronic portion is completly separate
è separata completamente dal sensore di rilevamento, from the sensing part which is in the form of an ex-
che si presenta esclusivamente come un prolungamento tension and can withstand temperatures up to 250°C.
della parte sensibile, resistendo a temperature fino a These products are used to control the levels of hot
+250°C. Tali apparecchiature sono utilizzate per il con- materials such as liquids, oil, powder and plastic
trollo di livello di materiali caldi come liquidi, oli, polveri e granules. They also sense solid metallic and non-
granulati plastici. Rilevano anche corpi solidi metallici e metallic bodies positioned in areas of high tempera-
non metallici situati in zone sottoposte ad alta temperatura. ture. The connecting cable between the sensor and
Il cavo di collegamento tra sensore ed amplificatore deve the amplifier must be of standard length (2m or 5m).
essere di lunghezza standard (2 mt oppure 5 mt), resiste It resists to temperatures from -200 to +250°C it is
a temperature da -200 ÷ +250°C, è fornito collegato al connected to the sensor and it is provided with a
sensore ed è provvisto di connettore schermato per il col- shielded connector for connection to the amplifier. The
legamento all’amplificatore. Gli amplificatori sono forniti amplifier is supplied in two different types, a model
in due modelli: uno idoneo per un sensore e l’altro per due which is suitable for one sensor and a model which is
sensori. I sensori di rilevamento sono forniti nei formati suitable for two sensors. The sensors can be supplied
M18x1 ed M30x1.5. in the following formats M18x1 and M30x1.5.
CARATTERISTICHE TECNICHE COMUNI SENSORI SC18M-HT / SC30M-HT SCHEMI DI COLLEGAMENTO / WIRING DIAGRAMS
TECHNICAL CHARACTERISTICS SENSOR SC18M-HT / SC30M-HT RELÈ / RELAY RELÈ 1 / RELAY 1 RELÈ 2 / RELAY 2
5A 220 Vac 5A5A 220 Vac 5A 5A
220220
VcaVac
• Custodia e ghiere di fissaggio in acciaio inox AISI 303. / Housing and fixing nuts in stainless steel AISI 303. 5A 220 Vca 220 Vca
• Temperatura min./max. di esercizio: da -200 ÷ +250°C. / Min./max. temperature range: -200 ÷ +250°C. 3
2 10
9 3
2 10
9
1 11 1 11
• Distanza di intervento (Sn) mod. SC18M-HT: 5 mm. / Switching distance (Sn) type SC18M-HT: 5 mm.
• Distanza di intervento (Sn) mod. SC30M-HT: 15 mm. / Switching distance (Sn) type SC30M-HT: 15 mm. 220 0 110 24 220 0 110 24
ALSC - 1 CH ALSC - 2 CH
• Grado di protezione: IP68. / IP rating: IP68.
CH 1 CH 2
ON
25 60 2000 / 5000
76
– + SENSIBILITY – + – +
SENSIBILITY
38 13 70
®
73
SENSORE CAPACITIVO TEMPORIZZATO DELAYED PROGRAMMABLE CAPACITIVE
MOD. SC30P-RE25T PROGRAMMABILE SENSOR SC30P-RE25T MODEL
CON USCITA A RELÈ RELAY OUTPUT
GENERALITÀ GENERAL DESCRIPTIONS
Questo sensore di prossimità appartiene This proximity sensor belongs to the
alla famiglia dei sensori capacitivi, forni- capacitive sensor family, it supplies a
sce un segnale di uscita al carico esterno signal to the external load which can be
con una temporizzazione regolabile fino a delayed up to 10 min. when any material
10 min., quando un materiale qualsiasi solid or liquid (water, glass, wood, metal,
solido o liquido (acqua, vetro, legno, me- coffe, powders etc.) come into the sens-
tallo, caffè, polveri, ecc.) interessa la sua ing area, it is used principally as a level
superficie attiva, viene utilizzato princi- control.
palmente come controllo di livello. This model is completly programmable
Questo modello è completamente pro- regarding the delay in energization and
grammabile per quanto riguarda le fun- de-energization with open or closed out-
zioni di temporizzazione all’eccitazione o put, the sensor does in fact contain a 1A
diseccitazione con contatto di uscita 220V chengeover relay.
aperto o chiuso, infatti il sensore è dotato Due to its versatility, programmability and
al suo interno di un relè con contatto di high power output compared to a normal
scambio di 1A a 220Vca. electronic sensor, the stocking of product
Per la sua versatilità inerente le funzioni for the wholesaler is simplified as is
programmabili e l’elevata potenza di the adaptability of the switch to any
uscita rispetto ad un normale sensore application.
elettronico, semplifica lo stoccaggio a This sensor can be used with the protec-
magazzino per il grossista e rende facile all’installatore l’adattabilità dell’apparecchiatura a tion housing SCM-R which is of POM and therefore satisfies the most severe abrasion
qualsiasi esigenza dell’impianto. resistance requirements.
Questo sensore può essere abbinato alla muffola di protezione tipo SCM-R in materiale When used as a level control, this housing allows for the sensor to be substituted
plastico atossico (POM) e quindi soddisfare anche le esigenze più gravose di controllo di whenever required.
livello inerenti l’abrasione o la sostituzione in caso di verifica o guasto del sensore stesso.
LED 50
MARRONE/BROWN
REG. TEMPO/ TIME ADJUST. RELÈ / RELAY BIANCO/WHITE
REG. SENSIBILITÀ 1 = 0,1 sec. + 1 min.
100 ROSSO/RED
SENSITIVITY ADJUST. B A 0
10 = 1 sec. + 10 min. 1A NERO/BLACK
Vdc/ac
Vcc/ca
SWITCH CAVO / CABLE 220 Vac BLU/BLUE
* Identificare il N° 100 della scala del trimmer di regolazione tempo con Tensione di alimentazione: lo stesso sensore può essere alimentato da
il fondo scala della gamma di temporizzazione (1 min. oppure 10 min.). 12÷50 Vcc e da 12÷240 Vca.
* The 100 on the time regulation trimmer scale corresponds to the full Multivoltage power supply 12÷50 Vdc / 12÷240 Vac.
scale of the time range of the sensor.
®
74
SENSORE CAPACITIVO DELAYED PROGRAMMABLE
TEMPORIZZATO PROGRAMMABILE CAPACITIVE SENSOR
MOD. SC30P-RE25T SC30P-RE25T MODEL
FUNZIONI PROGRAMMABILI PROGRAMMABLE FUNCTIONS
FUNZIONE TE NO - temporizzato all’eccitazione contatto N.O. FUNCTION TE NO - delay on energization N.O. contact.
Il sensore in assenza di materiale ha il contatto aperto. Quando il materiale entra nella In the absence of material the sensor has an open contact. When the material enters the
zona sensibile parte il tempo impostato dopo il quale il contatto si chiude (N.C.). Quando sensing area, the delay set starts. At the end of this time the contact closes. When the
esce, il contatto si riapre istantaneamente. material leaves the sensing area, the contact opens instantaneously.
FUNZIONE TE NC - temporizzato all’eccitazione contatto N.C. FUNCTION TE NC - delay on energization N.C. contact.
Il sensore in assenza di materiale ha il contatto chiuso. Quando il materiale entra nella In the absence of material the contact of the sensor is closed. When material enters the
zona sensibile il contatto si apre e quando esce parte il tempo impostato dopo il quale il sensing area, the contact opens. When material leaves the area, the delay set starts, after
contatto si chiude. which the contact closes.
FUNZIONE TD NO - temporizzato alla diseccitazione contatto N.O. FUNCTION TD NO - delay on de-energization N.O. contact.
Il sensore in assenza di materiale ha il contatto aperto. Quando il materiale entra nella In the absence of material the contact of the sensor is open. When material enters the
zona sensibile il contatto si chiude e quando esce parte il tempo impostato dopo il quale il sensing area, the contact closes. When material leaves the area, the delay set starts, after
contatto si apre. which the contact opens.
FUNZIONE TD NC - temporizzato alla diseccitazione contatto N.C. FUNCTION TD NC - delay on de-energization N.C. contact.
Il sensore in assenza di materiale ha il contatto chiuso. Quando il materiale entra nella In the absence of material the contact of the sensor is closed. When material enters the
zona sensibile parte il tempo impostato dopo il quale il contatto si apre, quando esce il sensing area, the delay set starts, after which the contact opens.
contatto si chiude istantaneamente. When material leaves the area, the contact closes instantaneously.
N.B.: Per ottenere le funzioni sopra descritte attenersi alla tabella «Funzioni N.B.: In order to obtain the above mentioned functions please refer to the table
programmabili» “Programmable functions”
130
110
M 30 X 1,5
Ø 41
20 65 27
®
75
MUFFOLA DI PROTEZIONE SCM PROTECTION HOUSING SCM TYPE
PER SENSORI CAPACITIVI M30 FOR M30 CAPACITIVE SENSORS
CON CERTIFICAZIONE ATEX ATEX APPROVED
GENERALITÀ SPECIFICATIONS
La muffola di protezione viene applicata come custodia protettiva Our housing is to be mounted as a waterproof protection to
stagna in abbinamento ai sensori capacitivi M30. La protezione our M30 capacitive sensors. Our SCM housing is made of non-
SCM é in materiale plastico atossico (POM) Ultraform S2320 toxic plastic material (POM), natural Ultraform S2320, suitable
naturale, idoneo per uso alimentare. Limiti di temperatura da for food applications. Temperature range from -20 ÷ + 70°C,
-20 ÷ + 70°C e pressione massima all’interno del serbatoio non max pressure inside the tank no greater than 8 bar and
superiore a 8 bar, attacco filettato 1”1/2 gas. threaded 1”1/2 connection.
La protezione SCM facilita la sostituzione del sensore in caso di SCM protection housing simplifies the sensor replacement in
avaria e lo protegge dall’abrasione dovuta allo scorrimento del case of malfunction and protects it from abrasion caused by
materiale all’interno del serbatoio. material sliding inside the tank.
La protezione SCM è fornita anche con certificazione ATEX adatta Our SCM protection housing is also available in the ATEX
per installazione sul confine tra la “zona 20” e la “zona 21” version, suitable for applications between ‘zone 20’ and ‘zone
oppure tra la “zona 20” e la “zona 22”. 21’ or between ‘zone 20’ and ‘zone 22’.
Può essere utilizzata da sola o in abbinamento con sensori capa- This can be used alone or combined with our ATEX approved
citivi ATEX serie AD1/2 come dispositivi del gruppo II, categoria capacitive sensors series AD1/2 group II, category 1/2;
1/2, idonei ad essere impiegati in atmosfera potenzialmente suitable for potentially explosive environments due to the
esplosiva dovuta alla presenza di miscele di aria e polveri presence of gas and dust ‘D’ mixtures, in conformity with CE
combustibili “D” in conformità alla Direttiva 94/96 CE. Directive 94/96.
Reg. sensibilità
Sensitivity adj.
SCM-P
ACC000002 Reg. sensibilità
Sensitivity adj.
LED SCM-P
C30000011
Molla di fissaggio
Fixing spring
SCM-R
ACC000004
N° 2 fori M4 contrapposti Ribasso per il fissaggio del sensore
per il fissaggio del sensore Slot for sensor fixing
N° 2 hole for sensor fixing
LED
SCM-R
N°2 viti di fissaggio
Reg. sensibilità N°2 Screw fixing C30000001 / C30000006
Sensitivity adj.
18 24 58
1 1/2" GAS
B
mPm
®
76