You are on page 1of 46

APT Power Technology

Contents

Contents
Primary Current Injection Test Sets

Model PI502 Single Phase Primary Current Injection Test Set 1

Model PI503 Single Phase Primary Current Injection Test Set 2

Model PI503 3000A Automatic Primary Current Injection Test Set 3


Model PI3505A Automatic Three Phase
4
Primary Current Injection Test Set
Model PI509 Single Phase Primary Current Injection Test Set 5

HI-POT Test Sets

Model AHP5/50 AC/DC Voltage Withstand Test Set 7

Model AHP15/120 AC/DC Voltage Withstand Test Set 9

Resonant Withstand Test Set-XZF1600KVA/640KV 11

Model DP 802 High Voltage DC Withstand Test Sets 14

Model DVDF50 Series Induced Over Voltage Withstand Test Set 16

Relay Test Set

Model SI211 Single Phase Relay Tester 19

Model SI313 Three Phase Relay Tester 21

Model SI614 Series Six Phase Relay Tester 24

Transformer Test Set

Model TTR 771 Transformer Turns Ratio Test Set 27

Model TO713 10A Transformer Ohmmeter 29

Model OT775 Single Cup Automatic Oil Tester 30


APT Power Technology
Contents

Circuit Breaker Test Set

Model CBT-V DC Circuit Breaker Test Set 31

Model VCT-III CB Vacuum Bottle Test Set 33

Model MVC CB Vacuum Bottle Test Set 34

CT Test Sets

High Accuracy CT Site Calibrating Test Sets 35

Model CT120P CT Analyzer 38

Others
Model DF901 Automatic 10KV Capacitance & Dissipation Factor Test
40
Set
Model LRM911 Low Resistance Ohmmeter 42

Model SGC-03T Switchgear Local Controller 43


APT Power Technology
Primary Current Injection Test Sets

Model PI502 Single Phase Primary Current Injection Test Set

Product Features:
Two range current output, 0~1000A/0~2000A
Output current can be adjusted continuously, from 0 to rated
value
AC single phase output
Easy to operate
On trolley so that can be moved easily.

Specifications
Input : 380V±10%, 15.8A, 50Hz±1%,
Output:
 a)Output Current:2000A, Output Voltage: 0~3V/50Hz±1%. in parallel
 b)Output Current:1000A, Output Voltage: 0~6V/50Hz±1%. in series
Duration: 3 minutes @rated current output
Duty Cycle: more than 10 minutes.
Capacity: 6KVA
Accuracy: 1.5%
Demensions:600×430×790mm (Instrument)
Net Weight :145Kg (Instrument)
Output Current Cable: 2500mmX2 pcs

Order Infor mation


Item Art. No.
Pi502
 Included Accessories:
 Output Current Cable: 2500mmX2 pcs
 Ground Cable

Version1.2,08-02-2009

1
APT Power Technology
Primary Current Injection Test Sets

Model PI503 Single Phase Primary Current Injection Test Set

Product Features:
Tw o r a n g e
R a m p e r e m e t e r, 0 ~ 1 2 0 0 A / 0
~3000A,selected by transfer switch on the
control panel
The shell of control module and primary
R
injection is produced with 2 mm cold roll steel
sheet, robust for use.
With universal wheel for control module, easy
R
move at the jobsite
Zero Protection for safety operation
R
Timing function and Emergency stop button are available
R

Specifications
vInput : 380V±10%, 50Hz±1%,
vOutput :
v Current:3000A, Open circuit voltage:6V
v Capacity: 20KVA
vDuration: 5 minutes @3000A
vSurface Temperature Rise for primary injection<75℃
vNo-load loss<2%
vNet Size and Weight for control module:630×450×800mm,75Kg
vNet Size and Weight for Primary Injection:550×490×600mm,120Kg

Order Infor mation


Item Art. No.
PI503
› Included Accessories:
›
Output Current Cable: 500mm2X3m, 2 pcs, covered with insulation
cloths outside
›
Power Cables:10mm2×2m, 4pcs( red 2, blue 2). 2pcs for power source,
another 2 pcs for connection between control module and primary injection
test.
› Instrument line: 4mm2×2m,2 pcs(yellow 1, green 1)
›
Ground Cable:4mm2×6m,2 pcs

Version1.2,08-02-2009

2
APT Power Technology
Primary Current Injection Test Sets

Model PI503 3000A Automatic Primary Current Injection Test Set

Product Features:
RThree test mode, manual, automatic or impact
RApply for current injection test or impact for CB quick-break test
R320X240 LCD, High speed printer inside
RDisplay output current and timing during process
ROver Current Protection, Zero Protection
REmergency stop button are available

Specifications
vInput : 380V±10%, 50Hz±1%,
v
Output :
² Current:3000A, Open circuit voltage:6V
² Capacity: 20KVA
v
Duration: 5 minutes @3000A
v
Range for Injection timing:0-999 seconds
v
Range for Impact timing:0-999 ms
v
Working Temperature:-20℃-50℃
v
Surface Temperature Rise for primary injection<75℃
v
No-load loss<2%
v
Net Size and Weight for control module:630×450×800mm,75Kg
v
Net Size and Weight for PrimaryInjection:550×490×600mm,120Kg

Order Information

Item Art. No.


PI3505A

Included Accessories:
œ Output Current Cable: 500mm2X3m, 2 pcs, covered with insulation cloths outside
œ Power Cables:10mm2×2m, 4pcs( red 2, blue 2). 2pcs for power source, another 2 pcs for
connection between control module and primary injection test.
Instrument line: 4mm2×2m,2 pcs(yellow 1, green 1)
Ground Cable:4mm2×6m,2 pcs

Version1.2,08-05-2012

3
APT Power Technology
Primary Current Injection Test Sets

Model PI3505A Automatic Three Phase


Primary Current Injection Test Set

Description:
The test set, model PI3505A are composed of two pieces. primary current
injector and its control module. The voltage regulator is positioned at
control module.
The test set is used for three phase primary current injection or CB Quick
Break Test.

Product Features:
R
Three test modes, automatic, manual or impact available
R
Current output, 3X0~5000A, adjusted continuously and synchronously
R
Current Output three phase or single phase,
R
LCD display, operated by buttons
R
Over current protection, zero protection
R
Test Duration can be set in advance
R
Three pcs of current head contacts

Specifications
vInput : 380V, 50Hz, three-phase four-wire system
vOutput: 3X0~5000A, Open Circuit Voltage:6V
vCapacity:30KVA per phase
vDuration set range 0-999 seconds both for injection and impact
vAmbient Temperature:-20℃-50℃
vCurrent output accuracy:1.5%(F.S)
vDuration:
3X0~1000A, continuously
Up to3X 2500A, on 30 minutes, off 30 minutes
3X5000A, on 5 minutes, off 15 minutes

Order Infor mation


Item Art. No.
PI3505A
Included Accessories:
œ Output Current Cable: 1000mm2×3000mm, 3 pcs
œ
Ground Cable, 1 piece
œ
Power input cable, 1 set
œ
Data cable, 1set
Version1.2,08-08-2012

4
APT Power Technology
Primary Current Injection Test Sets

Model PI509
PI502 Single Phase Primary Current Injection Test Set

Product Features:
RThe max. current output up to 20000A,Impact test below 20000A
RThree function in one body: current injection, CB test and impact test
RCurrent injection can be operated by automatic or manual mode.
RCan measure breaker's action time and action current; Value holding for CB action current
RCurrent preset and over current protection; Zero Protection; Alarm
RSuitable for current injection, temperature rise test
RCool by fans;
ROn trolley so that can be moved easily.

Control Panel for PI509 Primary Current Injection Tester

Specifications
v Output Current and its duration
0~2500A,continuously
Up to 4000A, one hour, off 30 minutes
Up to 7000A, 15 minutes, off 15 minutes
Up to 13000A, 1 minutes, off 15 minutes
Up to 20000A, 10 seconds, off 15 minutes
v Output opening voltage/short circuit voltage≤6V
v Capacity:120KVA
v Over current protection:7 ms

5
APT Power Technology
Primary Current Injection Test Sets

v
Range for CB action time:0.0001~999.9999 seconds, resolution:0.0001 second
v
Current output accuracy≥0.5% full scale
v
Insulation resistance≥2MΩtested with 500V mega meter.
v
AC withstand: 3KV, 1 minute.
v
Input coil upon output coil & earth; output coil upon input coil & earth
v
Input : 380VAC, 315.8A, 50Hz,
v
Dimensions & Weight)
Instrument Transportation
Dimensions(L×W×H) Weight Dimensions((L×W×H)) Weight
Primary Current 1110×1130×900mm 265 1250×1230×1110mm 300Kg
Control Panel 960×650×200mm 275 1080×770×2190mm 330Kg

Acknowledgement for Order


² This model is made according to customer's demands.
² Lead time: about 8 weeks
² It's better for us to obtain your requirements in details as that we can achieve your
functions fully. Meanwhile, reduce your cost.
²
It's better for you to order output current cables with primary current test set, so that we can
balance equipment performance roundly. Besides, it is convenient for equipment Routine
test.
Order Infor mation
 Item Art. No.
 PI509
Split structure, two blocks
Included Accessories:

œ
Input power cables, 60mm2×3 meter, 2 pcs.
œ
Output power cables for control panel/ Input power cables for primary tester, 60mm2×3
meter, 2 pcs
œ
Control cable, 2 pcs. One connects control panel and primary tester. Another for connects
control panel and CB.
œ
Ground leads, two pcs. One for primary tester, another for control panel
œ
Zero lead, one piece
œ
Output current cables, copper bolts, nuts, optional for order.

Version1.2,08-20-2011

6
APT Power Technology
HI-POT Test Sets

Model AHP5/50 AC/DC Voltage Withstand Test Set

Application:
AHP5/50 AC/DC Voltage Withstand Test Sets are mainly designed and produced for small
and medium capacity AC power frequency withstand test, also can be used for DC voltage
withstand test.
AHP5/50 AC/DC Voltage Withstand Test Sets are mainly composed of control unit and
AC/DC testing transformer(HV unit) which output AC voltage or DC voltage.
AHP 5/50 are fully automatic operated, with perfect monitoring and protection functions.
Please refer to its feature for details.
Besides main instrument, other optional can be provided in the package. Such as, Ball gap
frame, filter capacitor, water resistor, discharge rod, high voltage ground rod, high voltage
detector.

Product Features:
R
Auto/Manual Operating Mode
R
High Voltage, High Current, Duration for Withstand Test, Over Current Protection Setting
in advance
R
Live display of High Voltage(HV), High Current(HC), Low Voltage, and Low Current for
AC Output. Low Current for DC Output is displayed on Digital Milliamp-Microamp meter,
located on the top of silicon stack.
R
Display test result after test finished.
R
Over-current ,over-voltage and zero-start voltage protection, combined sound and light
alarm.
R
320×240 LCD
R
Build-in micro-printer .

Technical Specifications:
Control module parameters
²Capacity:5kVA
²Input voltage:AC220V±10% 50Hz±1
²Output voltage:0-200V
²Output current:0-25A
²Timing range: 0-999S
²Ambient temperature:-20℃ ~50℃
²Voltage accuracy:≤1% (F.S)
²Currency accuracy:≤1% (F.S)
Test transformer (HV unit) parameters
vCapacity: 5kVA
vLV side voltage: 0-200V
vLV side current: 0-25A
vH V s i d e v o l t a g e : A C 0 - 5 0 k V, D C 0 -

7
APT Power Technology
HI-POT Test Sets

70kV(negative)
HV side current: AC 100mA
v
v
Measuring voltage: AC 0-100V
HV side/LV side turns ratio: 250:1
v

Suggestion for Order


]
Output Voltage and Current is two very important parameters for the test sets. Basically,
Output Voltage of the instrument must more than test voltage of test object required
according to relevant Codes. Output current must be more than capacitance current of test
object.
]
All test transformer's output is alternative current, DC obtained by silicon stack rectifying.
However, silicon stack is half wave rectification. ripple factor big. If customer need DC
output very often, we suggest he could use High Voltage DC withstand test sets. For
example,DP801,802,803,804
]
If you need very big capacity test transformer for withstand test, very-low frequency or
Series Resonance Frequency should be better choice for you.
]
If you have any difficult for both parameters or product choice, please contact us freely.

Order Infor mation


Item Art. No.
AHP5/50
Test Transformer 1 piece
Control Module 1 piece
Test leads 1 set

Version1.2,12-02-2011

8
APT Power Technology
HI-POT Test Sets

Model AHP15/120 AC/DC Voltage Withstand Test Set

Application:
AHP15/120 AC/DC Voltage Withstand Test Sets are mainly designed and produced for
small and medium capacity AC power frequency withstand test, also can be used for DC
voltage withstand test.
AHP15/120 AC/DC Voltage Withstand Test Sets are mainly composed of control unit and
AC/DC testing transformer(HV unit) which output AC voltage or DC voltage.
AHP15 are fully automatic operated, with perfect monitoring and protection functions.
Please refer to its feature for details.
Besides main instrument, other optional can be provided in the package. Such as, Ball gap
frame, filter capacitor, water resistor, discharge rod, high voltage ground rod, high voltage
detector.

Product Features:
R
Auto/Manual Operating Mode
R
High Voltage, High Current, Duration for Withstand Test, Over Current Protection Setting
in advance
R
Live display of High Voltage(HV), High Current(HC), Low Voltage, and Low Current for
AC Output. Low Current for DC Output is displayed on Digital Milliamp-Microamp meter,
located on the top of silicon stack.
R
Display test result after test finished.
R
Over-current ,over-voltage and zero-start voltage protection, combined sound and light
alarm.
R
320×240 LCD
R
Build-in micro-printer .

Technical Specifications:
v
Input voltage: AC380V±10% 50Hz±1(three phase and four wire)
v
Input current: 0-37.5Aac
v
Output Voltage: AC 0-120kV,DC 170kV
v
Output Current: AC 125mA
v
Output capacity: 0-15kVA
v
Timing range: 0-999S
v
Working Cycle:1 hour on, 30 minutes off
v
Operating temperature: 0℃~40℃
v
RH:85%,no dew
Voltage accuracy: ≤1% (F.S)
v
v
Currency accuracy:≤1% (F.S)

9
APT Power Technology
HI-POT Test Sets

Figure 1.Overall Composition for AHP15/120

Suggestion for Order


²
Output Voltage and Current is two very important parameters for the test sets. Basically,
Output Voltage of the instrument must more than test voltage of test object required
according to relevant Codes. Output current must be more than capacitance current of test
object.
²
All test transformer's output is alternative current, DC obtained by silicon stack rectifying.
However, silicon stack is half wave rectification. ripple factor big. If customer need DC
output very often, we suggest he could use High Voltage DC withstand test sets. For
example,DP801,802,803,804
²
If you need very big capacity test transformer for withstand test, very-low frequency or
Series Resonance Frequency should be better choice for you.
²
If you have any difficult for both parameters or product choice, please contact us freely.

Order Infor mation


Item Art. No.
AHP15/120
œ Test Transformer 1 piece
œ
Control Module 1 piece
œ
Test leads 1 set

Version1.2,12-02-2011

10
APT Power Technology
HI-POT Test Sets

Resonant Withstand Test Set-XZF1600KVA/640KV

1.Description:
The resonant withstand test set is specially designed for AC withstand test of
150KV cable and 150KV& 500KV GIS. The whole test set consists of variable
frequency power source, excitation transformer, 4 pieces of inductors, and high
voltage detector(capacitive voltage divider). Serial & parallel connections of different
combinations of 4 pieces of inductors are able to satisfy different kinds of test
requirement as below.
Devices combination Excitation. High
In ductor Test
Mode transformer Voltage
400kVA/160kV 4 pieces vol tage
Test object output detector
Within 200m 1 piece of inductor
150kV/1 000 2 00-500m 2 pieces of inductor are parallel
2
6kV 350kV 160kV
mm cable 5 00-700m 3 pieces of inductor are parallel
700-1000m 4 pieces of inductor are parallel
150kV GIS 2 pieces of inductor are serial 12kV 350kV 275kV
500kV GIS 4 pieces of inductor are serial 24kV 700kV 596kV

2.Product Features:
R
Variable frequency resonance type
R
Test both cable and GIS with different connections.
R
Creative design, High Voltage Tester not only one instrument to measure high voltage, but
as one capacitor to compose the test set.
R
Manual or Automatic Test Mode
R
Q value more that 30
Over Current Protection , Over Voltage Protection, Atc Protection for Tested Object
R
R
Output Wave: Sine Wave,Wave Aberration Rate≤1%

3.Test Object & Voltage:


²
XLPE Cable, Rated Voltage150kV ,estimate length 1000 meters(1000mmsq),
Equivalent capacity≤0.22uF, Test Frequency:30~300Hz, Test Voltage:160KV
150KV GIS, Test Frequency:30~300Hz ,test voltage 275KV
²
500KV GIS, Test Frequency:30~300Hz ,test voltage 596KV
²

4.The Test Set Composed of:


³ Exciting Transformer, 60kVA/6kV/12kV/24KV, oil immersed,1 piece, about
350Kg
³ Variable Frequency Power Supply, 60kW/380V,1 piece, about 150Kg
³ High Voltage Inductor,400KVA/160KV,4 PCS, oil immersed , 500Kg/piece
³ High Voltage Tester,350KV/400pf, 1 piece, about 45Kg

5.Main Specifications:
v
Rated Capacity:1600KVA

11
APT Power Technology
HI-POT Test Sets

v
Input: 3-phase,380V,50Hz
v
Rated Voltage:160KV,320KV,640KV
v
Rated Current:10A, 5A,2.5A
v
Test Frequency: 30~300Hz
v
Output Wave:Sine Wave
v
Wave Aberration Rate≤1%
v
Duration: Rated test object,60 minutes, Over Voltage 110% 60 seconds( For single
HV inductor,over voltage 120% 60 second, for whole set, over voltage 110% 60
second)
v
Temp.Rise: Rated test object,60 minutes continuous operation, less than 65K
Q Value ≥30(f=45Hz)
v
Over Current Protection , Over Voltage Protection, Arc Protection for Tested Object
v
v
Measuring Accuracy: RMS1.5%
Temp. 0℃ ~45℃
v
v
RH≤90%,No dew
v
Altitude≤1000m

The starting interface

12
APT Power Technology
HI-POT Test Sets

6. Order Infor mation


6.1 For Order
Difference from other universal tester, Resonant tester is designed and produced
according to customer’s specific requirements.
œ What Test objects are,
œ Specifications of Test object is, for example equivalent capacity for cable, rated
voltage for GIS
œ Test voltage is for each test object according to your country’s relevant regulations
This is very complex job. If you have any difficulty, please contact us freely.
6.2 Manufacturer Promise
We promise the test set can be operated normally precondition the customer
provides us correct information which the system designed necessary.
6.3 For customer site service
We can provide customer site service, including connections, commissioning, test
and training , based on customer cost.
6.4 The third Party Calibration in China
We can provide the third Party Calibration in China based on customer cost.
6.5 Factory Test Witness
We welcome customer to participate in factory test witness.
6.6 Lead time
Six weeks for rated voltage less than 600KV, 8 weeks for rated voltage more than
600K

Version1.2,31-08-2012

13
APT Power Technology
HI-POT Test Sets

Model DP 802 High Voltage DC Withstand Test Sets

DP 802 high voltage DC Withstand test sets, provide DC high voltage source for checking
the quality of power cablse, inslators,transformers,motors,switchgear and capacitors.
The test set are composed of two modules, one is control module, another is high voltage
module.

Product Features:
R
Full-wave rectification
R
Digital metering and display
R
High accuracy, low ripple ratio
R
Air-insulated,Epoxy resin cylinder
R
Fast Charging for high capacitance samples
R
Continuously variable test voltage
R
With 0.75UDC1mA function button, zinc oxide arrester can be measured.
R
Small in size, light weight, both control module
R
and high voltage module can be put into one suitcase .

Technical Specifications:
Input Power
v
Nominal 220Vac 50Hz
Output
v
ª
Rated voltage:120KVdc,rated current :5mA. Rated for 2mA or 10mA are available.
ª
Working Cycle:5mA for 20 minutes, off 20 minutes; 2 mA continuous
ª
Ripple less than 2%
Working temperature: 0 ° C to 40 ° C
v
Relative humidity: ≤ 85%, no dew
v
Above Sea Level:less that 1500m
v
Size :Ф76mm×800mm (HV Tank),
v
220mm×220mm×600mm(Instrument Suit)
Weight: 20 Kg
v

14
APT Power Technology
HI-POT Test Sets

Acknowledgement for Order


²
More models and their specifications to be listed

Output Current Height of Weight


Model Test Voltage Remark
(220Vac Input) HV Tank(m) (Kg)
2mA for 30 minutes, off 10
DP800 0~30KVdc 0.3 13 Portable
minutes; 1 mA continuous
2mA for 30 minutes, off 10
DP801 0~60KVdc 0.5 16
minutes; 1 mA continuous
5mA for 10 minutes, off 20
DP803 0~200KVdc 1.2 26
minutes; 2 mA continuous
5mA for 5 minutes, off 20
DP804 0~300KVdc 1.7 31
minutes; 1.5 mA continuous

Made to order
²
The special models for Input Voltage 120V, Frequency 60Hz are available subject
to made to order.
2mA and 10mA are available for Model DP802,803and 804.

Order Infor mation


Item Art. No.
DP 802
œ High Voltage Module(120KVdc,5mA) 1 Piece
œ Control Module 1 Piece
œ Micro Ammeter 1 Piece
œ Test Wires 1 set

Version1.2,02-08-2011

15
APT Power Technology
HI-POT Test Sets

Model DVDF50 Series Induced Over Voltage Withstand Test Set

Applications:
Induced overvoltage withstand test set , also called induced voltage induced frequency
test set , Double voltage & double frequency test set, DVDF motor generator test, Motor
generator tests, or High frequency generator.
The test set provides a continuously variable output voltage at double or Three times
frequency to test transformer insulation performance between turns of coils, layer to layer.
Model DVDF 50 series test set suit for capacity ≤5000KVA Transformer .

The set consists of:


3-phase squirrel cage asynchronous motor , rated frequency , 50Hz , one piece
²
3 - phase synchronous generator , rated frequency , 100Hz or 150Hz or 200Hz , one piece
²
Control module function : motor start up device , generator parameters display , generator
²
exciting adjust and exciting parameters display , generator protection . etc .
The motor and generator are positioned on the same one pedestal, and connected with steel
couples. The exciting system is integrated into the generator

Fig.1 Test set with control panel

16
APT Power Technology
HI-POT Test Sets

Working Principle:
While this motor drives the synchronous generator up to rated rotate speed,input
exciting current (DC)to the generator winds of rotor. Since generator’s rotor is
running,therefore,the generator will output electricity.Output voltage change with
exciting current.
T ransformer

M otor G enerator

A C 380V C ontrol
P anel M G
Excitation

U I

Fig.2 test principle


How connection:
An alternating voltage of sine wave form (as much as possible) at double or three times
frequency (100 Hz or 150Hz or 200Hz) and double voltage in amplitude is applied at one
side of the transformer under test while the windings, which are not connected to the source
of excitation, are left on open circuit. This higher frequency is considered to avoid excessive
excitation current during the testing.

Product Features:
R
DC no-carbon- brush excitation.
Output: Constant frequency(100Hz or 150Hz or 200Hz) , variable voltage(80- 800V)
R
Digital Display: Output Current( three phase) , Output Voltage, Output Frequency
R
Input Current, Input Voltage, Exciting current , Exciting
VoltageTime
R
Indication: Power, zero, Open/Close.etc
R
Buttons: Power Start, voltage up, voltage down,etc
R
Test duration can be preset by time controller.
R
The exciting system is integrated into the generator
R
Connection Type: delta
R
Start up mode for motor: star-delta
R
Direction of the motor : Should be clockwise.
R
Protection against over load, over heat provided. Zero Protection

Specifications
v
Input to motor:380V, 50Hz,
Output Voltage :80-800Vac
v
v
Output Frequency: 100, 150,or 200Hz( Each one model, each one frequency)
v
Rated output current: about 36. 8A
Rated exciting current <1 A, Rated exciting voltage<100Vdc,subject to load.
v
v
Capacity: 50KVA
v
Suitable for induced over voltage withstand test of transformer
v
PF:0.5(lag)
v
Insulation Level: H
v
Outlet: 6 Terminals out
v
Wave Aberration Rate at No load state≤3%

17
APT Power Technology
HI-POT Test Sets

v
L-L Voltage unbalance rate(The cold and hot state)≤2%
v
Operation Mode: continuous within 2 hours
v
Over voltage: 130% rated voltage, 3 minutes
v
Insulation Level: F
v
Size and Weight
Motor-Generator set: 1300mmL× 550mmW ×650mmH, Weight:1500Kg
Control panel:800 mmLX800 mmWX1200 mmH,120Kg
v
Temp:-15-40℃
v
RH<90%
v
Altitude<1000meters

Order Infor mation:


œ
Motor and its generator, all same one
œ
Control module, alternative panel or console style. Same Price
œ
Different Price for Different Models
Model DVDF50 A, Output Frequency 100Hz
Model DVDF50 B, Output Frequency 150Hz
Model DVDF50 C, Output Frequency 200Hz

Version1.2,08-03-2012

18
APT Power Technology
Relay Test Set

Model SI211 Single Phase Relay Tester

Description:
SI211 Single phase relay tester provide 2 phase currents output and 1 phase voltage
output separately, ac or dc; 1 phase auxiliary DC output still available.
Its ac voltage output can reach up to 150V, meets most requirement in the world.
SI211 include 6 test modules as below:
² Any test, This module will provide user with a convenient tool to realize fast test. User
will have full control ofall voltage and current sources independently.
² Current test,This module will be use to test different current relays. For example,over
current, instantaneous over current, directional over current
² Voltage test, This module is used to test voltage relays
² Df/dt test, This module can be used to test df/dt and frequency relay
² Power directional test,This module is used to test power directional relays.
² I-t test,This module is used to test current-time characteristics of an inversed time current
relay

Product Features:
R
EMC, apply for IEC61000-4-2/3/4
Voltage output up to 150Vac
R
R
AC or DC power input
R
DSP applied, large color LCD display, panel control;
R
Test data can be transferred to compute via RS232
R
Plug-in modules structure, easy for hardware update or maintenance.

Specifications
v
Current Output
ª Output Range
2 phase AC/DC(L-N):2 × 0 … 30 A
1 phase AC/DC(L-N):1 × 0 … 60 A
ª Output Power
2 phase AC/DC(L-N):2 × 250 VA
1 phase AC/DC(L-N):1 × 1000 VA/W
Accuracy:reading 0.2%,or full scope 0.04%
ª
ª Degree of distortion< 0.5%
ª Resolution:2.0 mA
v
Voltage Output
ª Output Range
1 phase AC:1 × 0 … 150 V
1 phase DC:1 × 0 … ±211 V
ª Output Power

19
APT Power Technology
Relay Test Set

1 channel AC:1 × 50 VA
1 channel DC:1 × 80 W
ª Accuracy : reading 0.2%,or scope 0.04%
ª Degree of distortion< 0.5
ª Resolution:5.0 mV
v
General Parameters for output current/voltage
ª Frequency Range
Static: DC ... 1000 Hz
Transient: DC ... 3000 Hz
ª Frequency Accuracy:0.01%
ª Frequency Resolution:0.001Hz
ª Phase Range: -360° ... +360°
ª Phase Accuracy< 0.2°
ª Phase Resolution:0.05°
v
Auxiliary DC output
ª Output Range:220 V/110 V
ª Power:80 W
v
Binary Input
Number:2
ª
Type:3.5 - 250 Vdc,or potential free
ª
Resolution:50 µs
ª
Max. time measure:999 s
ª
v
Power Input
ª Rated voltage range: 150…250 Vac / 220 Vdc
ª Allowed voltage range:120 …265 Vac / 220 Vdc±10%
ª Rated frequency:50… 60 Hz
ª Allowed frequency:45…65 Hz
v
Environmental Conditions
ª Ambient temperature: -5 … +50°C
ª RH:90%
ª EMC:IEC61000-4-2/3/4
v
Others
Size: 470 × 150 × 263 mm
ª
ª
Weight:8.5Kg
ª
PC connection:RS232, each one at front and back pannel,optically isolated

Order Infor mation


Item Art. No.
SI211 one piece
Accessories: Test leads
Input cable
Version1.2,08-20-2010

20
APT Power Technology
Relay Test Set

Model SI313 Three Phase Relay Tester

Description:
SI313 Three phase relay tester provide 3 phase currents output and 3 phase voltage
output separately, and one special voltage– current convertible output , Binary Input and
out.
Its ac voltage output can reach up to 300V, meets most requirement in the world.
SI313 include 13 test modules as below, 14 modules for personal computer
ª Any test, This module will provide user with a convenient tool to realize fast test. User
will have full control ofall voltage and current sources independently.
ª Current test,This module will be use to test different current relays. For example,over
current, instantaneous over current, directional over current
ª Voltage test, This module is used to test voltage relays
ª Df/dt test, This module can be used to test df/dt and frequency relay
ª Power directional test,This module is used to test power directional relays.
ª I-t test,This module is used to test current-time characteristics of an inversed time current
relay
ª Zone verification, This module will check the impedance settings for different zones of
an impedance relay
ª Zone mapping, With this module we can automatically map out the impedance
characteristics of an impedance relay.
ª Differential test, This module is used to test Ir/Id characteristic of transformer
differential relay.
ª Harmonic test
ª System setting

Product Features:
R
Voltage output up to 300Vac
R
All generators are independent
R
One special generator which can output current or voltage
Large color LCD , keyboard and rotating mouse
R
R
Can use external USB / PS2 Keyboard or mouse to operate
R
Overload and short circuit protection
R
Plug-in modules structure, easy for hardware update or maintenance.
R
Can work in vertical or horizontal position
R
Apply for C hinese S tandard DL/T624-1997

Specifications
v
Current Generators
² Setting range: 3-phase ac(L-N) 3×0…40 A ,1-phase ac(3L-N) 1×0…120A
² Power: 3-phase ac 3×300 VA

21
APT Power Technology
Relay Test Set

² Accuracy: 0.15% typical ≤0.2% guaranteed(1-25A)


² Resolution: 1.2mA
² Distortion: <0.1% typical
v
Voltage Generators
² Setting range: 3-phase ac (L-N) 3×0…300 V ,1-phase ac (L-L) 1×0…900 V
² Power: 3- phase ac (L-N) 3×50 VA,3-phase dc 3×50 W
² Accuracy: <0.1% typical, ≤0.2% guaranteed(>10 V)
² Resolution: 10 mV
² Distortion: <0.1% typical
v
Voltage Current Convertible Output( VI/DC)
² Voltage Mode Current Mode
² Range: 0-176 VAC Range: 1 x 0-1A Ac/dc
or 0-250V dc
² Power: 1x 80VA/W max Power: 1 x 80 VA/W max
² Accuracy : 0.2%(10-Vmax) Accuracy:0.2%(0.1-1A)
² Resolution: 7.0 m V Resolution: 0.1 m A
v
Frequency
² Range: Sine wave DC-1KHz /Transient: DC– 3 KHz
² Accuracy: 0.01%
² Resolution: 0.001 Hz
v
Phase angle
² Range 0-360°
² Accuracy : 0.2°
² Resolution : 0.05°
v
Binary Inputs: 8 nos : Auto detect type
² No: 1-4: Polarity independent , No: 5-8 : Polarity sensitive
² Max measuring time : 419s
² Resolution : 50 μs
² Sensing type: Dry or wet contacts
² Sensing range: 24 ~ 250 V dc
v
Binary Outputs: 2 Nos.
² Potential free relay contacts Controlled by software.
² Breaking capacity: 10 A /120 V ac, 5A/30V dc
v
Control Mode: Front panel/ PC Connection ( Selection switch rear side)
v
PC Connection: Ethernet , 10 Mbps
² Ground Socket : Front side
² USB, PS2 port: 1 each front side.
v
Analogue Inputs ( Optional): 2 nos
² Voltge input : 0-± 10 V
² Current Input: 0- ± 20 m A
Accuracy: 0.05% ( Typical)
v
Power Input
² Voltage range:110 …265 Vac
² Frequency range:45…65 Hz

22
v
Environmental Conditions
² Ambient temperature:-5 … +50°C
² RH:5-95%,no dew
v
Others
² Size: 470 × 194 × 370 mm
² Weight:15 Kg

Order Infor mation


Item Art. No.
SI313 one piece
Accessories: Test leads
Input cable

Version1.2,08-20-2010

23
APT Power Technology
Relay Test Set

Model SI614 Series Six Phase Relay Tester

Description:
SI614 series six phase relay tester provide 6 phase currents output and 4 phase
voltage output separately. Its ac voltage output can reach up to 300V, meets most
requirement in the world. Complete differential acting test of transformer at one time.
SI614series include 14 test modules as below:
R Any test, This module will provide user with a convenient tool to realize fast test. User
will have full control ofall voltage and current sources independently.
R Current test,This module will be use to test different current relays. For example,over
current, instantaneous over current, directional over current
R Voltage test, This module is used to test voltage relay
R Df/dt test, This module can be used to test df/dt and frequency relay
R Power directional test,This module is used to test power directional relays.
R I-t test,This module is used to test current-time characteristics of an inversed time current
relay
R Zone verification, This module will check the impedance settings for different zones of
an impedance relay
R Zone mapping, With this module we can automatically map out the impedance
characteristics of an impedance relay.
R Differential test, This module is used to test Ir/Id characteristic of transformer
differential relay.
R Harmonic test
R System setting

Product Features:
ª
EMC, apply for IEC61000-4-2/3/4
ª
Voltage output up to 300 Vac
ª
AC or DC power input
ª
Self-calibrating function can ensure its accuracy during long time
ª
Support two SI 614 Output simultaneously by GPS, error less that 50us
ª
Wave record Playback for COMTRADE format trouble
ª
Can create customer style test report and transfer it into Microsoft Office format
ª
Automatic or manual test for all kinks of relay testers and their parameters, such as
amplitude, phase, frequency, etc, static or dynamic
ª
Sets test for protection device. For impedance relay, can complete both setting for
distance protection and zero-sequence protection within one time.
ª
Can fulfill 3 phase DP( Differential Protection) test one time
ª
Can test distance relay and allow customer define distance relay characteristics
ª
DSP applied, panel control;
ª
Plug-in modules structure, easy for hardware update or maintenance.

24
APT Power Technology
Relay Test Set

Specifications
v
Current Output
² Output Range
6 phase AC/DC(L-N) : 6 × 0 … 25 A
3 phase AC/DC(L-N) : 3 × 0 … 50 A
1 phase AC/DC(L-N) : 1 × 0 … 150 A
²
Output Power
6 phase AC/DC(L-N):6 × 250 VA
3 phase AC/DC(L-N):3 × 500 VA
1 phase AC/DC(L-N) : 1 × 1200 VA/W
² Accuracy:reading 0.1%,or full scope 0.01%
² Degree of distortion< 0.2%
² Resolution:1.0 mA
v
Voltage Output
² Output Range
4 phase AC:4 × 0 … 300 V
1 phase AC:1 × 0 … 1200V
4 phase DC:4 × 0… ±423 V
1 phase DC:1X 0…±1692 V
²
4 channel AC:4 × 50 VA
1channel AC:1 × 200 VA
4channel DC:4 × 50 W
1channel DC:1 × 200 W
² Accuracy: reading 0.1%,or scope 0.01%
² Degree of distortion< 0.2
² Resolution: 0 … 75V:1.0 mV;75 … 300V:10 mV
v
General Parameters for output current/voltage
² Frequency Range
Static: DC ... 1000 Hz
Transient: DC ... 3000 Hz
² Frequency Accuracy:0.01%
² Frequency Resolution:0.001Hz
² Phase Range:-360° ... +360°
² Phase Accuracy< 0.2°
² Phase Resolution:0.05°
v
Binary Input
² Number:8
² Type:10 - 250 Vdc,or potential free
² Resolution:50 µs
² Max. time measure:999,999.999 s
v
Power Output
² Number:4

25
APT Power Technology
Relay Test Set

² Type:potential free or soft control


² AC Break: 0.5 A, 250 Vac
² DC Break: 0.5 A, 60 Vdc
v
Environmental Conditions
² Ambient temperature:-5 … +50°C
² RH:90%
² EMC:IEC61000-4-2/3/4
v
Others
² Size: 470 × 194 × 370 mm
² Weight:15Kg
² PC connection:RS232, each one at front and back pannel,optically isolated

Order Infor mation


Item Art. No.
SI614 one piece
Accessories: Test leads
Input cable

Version1.2,08-20-2010

26
APT Power Technology
Transformer Test Set

Model TTR 771 Transformer Turns Ratio Test Set

Product Features:
R
Test range wide, the highest can reach up to 10000.
R
Suitable for single phase, three phase and Z-shaped connection transformer.
R
Fast test speed, completion TTR test of three-phase transformer within 11 seconds.
R
Blind test for turns ratio and groups.
R
8 output terminals, including neutral point
R
Data display, storage and output
² LED display test procedure and data.
² Data printing
² 480 groups data storage
² RS485 and USB available.
R
Protection
² Wrong connecting protection for High-voltage terminals
and low-voltage terminals.
² Wrong connecting protection for 380V input power
supply
² Short Circuit protection for both transformer and its turn-
to-turn.
R
Small size, light weight.

Technical Specifications:
v
Range & Accuracy

Sampling Voltage AC160V AC10V


Range 0.9-10000 0.9-200
<500 ±0.1%
Accuracy 500-3000 ±0.2% =200 ±0.3%
>3000 ±0.5%

v
resolution: minimum 0.0001
v
power supply: AC220V ± 10% ,50/60 Hz±1HZ
v
the use of temperature: -20 ° C to 40 ° C
relative humidity: ≤ 80%, no dew
v
v
Exterior size :320mm×275mm×140mm (instrument),
395mm×240mm×250mm(test leads)
v
Net Weight: 4.5 Kg( instrument), 6 Kg(test leads)

27
APT Power Technology
Transformer Test Set

Compare with TTR773


ª
Specifications

TTR771 TTR773
Range 0.9-10000 0.9-5000
Interface RS485,USB N/A
Data Storage 480 groups 50 groups
AC220V ± 10% ,50/60
Input Power AC220V ± 10% ,50 Hz±1HZ
Hz±1HZ
Output
8pcs,including neutral point 6pcs,excluding neutral point
Terminals
320mm×275mm×140mm,4.6K
Size and Weight 395mm×240mm×250mm,6 Kg
g

ª Applications
TTR773 is one very typical transformer turns ratio test set, widely used for Grid, substation
and power plant.
TTR 771 is designed for high-end customers which date upload & analysis functions is
required. TTR771 is usually positioned at electrical test vehicles, and controlled by one
compute with other test instrument. It is also one part of transformer test table together with
transformer resistance tester, transformer tap change test set. and so on.

Order Infor mation


Item Art. No.
TTR771
œ Instrument 1 piece
œ Test Wires 1 set

Version1.2,08-02-2011

28
APT Power Technology
Transformer Test Set

Model TO713 10A Transformer Ohmmeter

Product Features:
R
Test three phase at the same time, Automatic calculation of three-phase unbalanced rate
R
Automatic selection of the output current, the max. value can reach up to 10A
R
Wide range, 0~100Ω. Suitable for resistance test for inductive load. Such as transformer
and instrument transformer
R
Rapid magnetization test for large capacity transformer
R
Automatic temperature conversion function, to resistance value 75 ° C
R
Data display, storage and output
²
LCD display ,English menu, Easy to operate.
²
Data printing
²
100 groups data storage
²
RS485 and USB available.
²
Self-discharge function, discharge alarm
²
Measurement results, steady, reliable and high accuracy.
²
Wrong connecting protection for 380V input power supply
²
Shockproof, anti-interference, suitable for jobsite.
²
Technical Specifications:
v
Range,0~100Ω,accuracy, 0.2%±0.2μΩ,resolution, 0.1μΩ
v
Test current,0~10A, automatic selection as per test range
v
Test voltage:24Vdc
v
Input, AC 220V±10%,50Hz±1 Hz, fuse,2A
v
Working temperature: 0 ° C to 40 ° C
Relative humidity: ≤ 80%, no dew
v
v
Size :410mm×330mm×190mm,Weight: 10 Kg

Order Infor mation


Item Art. No.
To713
œ Instrument 1 piece
œ Accessories refer to packing list

Version1.3,09-01-2011

29
APT Power Technology
Transformer Test Set

Model OT775 Single Cup Automatic Oil Tester

Product Features:
R
Full-automatic operation, automatically boosting, voltage holding, stirring, discharge,
calculate and printing test data.
R
Up to 80KV of Output voltage, meet almost all oil test application.
R
Two kinds of test mode, successive 6 times test for average value or only one test for single
value.
R
Nixie tube display, could endure very hot/low temperature.
R
Voltage automatic back to zero after oil breakdown.
R
Easy to operate

Specifications
v
Testing Voltage:0~80KV
v
Accuracy:1.5%
v
Boosting Speed:3KV/s
v
Electrode Shape: Standard Plate
v
Electrode Clearance:2.5mm, adjustable
v
Input : 220V±10%, 50Hz±1%, fuse,5A
v
Max. power consumption:200W, breakdown moment
v
Working Temperature:-100C~500C
v
RH≤80%,no dew
v
Demensions:430×350×300mm (Instrument)
v
Net Weight :23Kg (Instrument)

Order Infor mation


Item Art. No.
OT775
One set

Version1.2,08-02-2009

30
APT Power Technology
Circuit Breaker Test Set

Model CBT-V DC Circuit Breaker Test Set

Description:
DC circuit breaker tester set is used for mechanical
characteristic test of CB action device.
Model CBT-V can test up to 6 gaps of circuit breaker
simultaneously
Model CBT-V has very powerful software function,
together with CBT-V hardware can test all parameters at
different test methods according to IEC standard. Fully
suitable for international markets.
Furthermore, Model CBT-V is on market more than 5
years, is most popular model in China. Xi’an High
Voltage Apparatus Research Institute Co.,Ltd, which is
most authority in the field of CB test in China, use
Model CBT-V to test all CB around China.

Product Features:
R
IEC standard applied for
R
Up to 6 gaps of circuit breaker can be tested
R
Two test mode: by the tester itself or external computer by USB interface
R
With large color LCD, test curves can be displayed in different color
R
DC Power Source inside for CB tested action: Open/Close of CB’s contacts, DC motor
rotation for CB spring stretch.
R
Universal sensor clamp, suitable for almost all CB action device.
R
All test data can be printed by instrument it self or issue test report by computer software
R
All data can be sorted and analyzed by date, CB serial number….
R
Easy operate, automatically complete the test of single-closing, single-opening by pressing
the button of test, also displaying the test result.
R
Automatically identify CB position of open or close to avoid the incorrect operation
R
Six CB O/C state can be carried out: single open, single close, O-θ-CO, O-θ-CO-t-CO,CO-
t-CO
R
Selectable installing the sensor on one of the A-phase, B-phase & C-phase of gap1 or gap2
R
Alternative for displacement transducer or angular displacement transducer, the former is
first choice.
R
Three CB C/O control modes: internal control, external control, manual operate.
R
Accurately test the current peak value of opening & closing coil as well as current varying
curve.
R
Four kinds of travelling speed for moving contact can be defined: percentage of total
travel, percentage of open distance, time ,travel
R
Directly & accurately measure the contact open distance,
R
Be able to test and display the gap wave form, bouncing amplitude, bounce ,over-travel,

31
APT Power Technology
Circuit Breaker Test Set

R
Be able to test circuit breaker mechanical characteristics such as asynchronism, opening &
closing speed, opening & closing time.

Specifications
v
Time-travel characteristic curve of sampling frequency, 40KHz,16 digits
v
Time measurement range, 0.1 ms~999.9ms
v
Time precision, ±0.05ms
v
Time resolution, 0.025ms
v
Speed measurement range, 0.01 m/s~20m/s
v
Speed precision, 1% reading±0.02m/s
v
Speed resolution, 0.01 m/s
v
Travel measurement range, 0~999.99mm
v
Travel precision, 0.05%
v
Travel resolution, 0.1mm
v
Coil current waveform of sampling frequency, 40KHz
Sampling precision, ≤0.1%
v
v
Coil current measurement range, 0~15A normal,0~300 A for customer order
v
DC power source inside:
v
The maximum output current, 10A. Additional AC contactor is needed if the current over
10A; voltage output range,25 V~300V
v
Allowable external power supply if the switching power can’t work normally,0-10A
v
Power supply, AC 220V±10%50Hz±5Hz
Ambient temperature, -10℃~60℃
v
Relative humidity, ≤90%
v
v
Basic requirements for external computer: Windows XP, Office 2003, Access database

Order Infor mation


Item Art. No.
CBT-V 1 piece
Included Accessories:
œ Signal cable connecting to CB gaps, 5 cores, 1 piece
œ DC power cable for CB O/C and DC motor, 1 set
œ Signal cable connecting to sensor,1 set, with two sensor. One is displacement transducer ,
œ another is angular displacement
œ Senor universal Clamp, 1 set
œ Power input cable, 1 piece
œ Grounding cable, each piece
œ Software, free, including drive program

Version1.2,08-02-2009

32
APT Power Technology
Circuit Breaker Test Set

Model VCT-III CB Vacuum Bottle Test Set

Description:
Model VCT-III CB vacuum bottle test set is designed for vacuum test of vacuum circuit
breaker(VCB).Adopting Ionized electric charge method, the test set is the most precise
instrument for VCB vacuum test in the world.
The advantage of the test set as below:
ª Compared with those one test vacuum based on ac withstand method, Model VCT-III can
be quantitative measure;
ª Compared with those one test vacuum based on Ionized electric charge also, Model VCT-
III measure the density of Ionized electric charge, not current value of Ionized electric
charge.
ª In addition, Model VCT-III matching flexible magnetic control coil, most suitable for site
use.
Product Features:
R
Based on Ionized electric charge technology
R
Improve test accuracy by adopting special energy-enlarged decice;
R
Twice-sampling to deduct the leakage current due to environmental factors,
R
30KV AC Voltage Output is applied for ionizing electric charge of VCB. For those one full
air vacuum bottle, will be breakdown.
R
Over voltage protection for the instrument even if leakage vacuum bottle is breakdown.
R
43 pieces of standard measurement curve of vacuum arc-extinguishing chamber are
available

Specifications
Range: 1×10 -5 ~1x10 -1Pa,
v
v
Accuracy: within 1×10-4~1×10-1 Pa, the error<10%
Resolution : 10 -5Pa
v
v
Output voltage: maximum30KV
v
Environmental temperature: 0℃~55℃.
Relative humidity <85%RH
v
v
Input:AC220±l0%, 50Hz

Order Infor mation


Item Art. No.
VCT-III 1 piece
Included Accessories:
œ Power input cable, Signal cable , each piece
œ Grounding cable, each piece
œ flexible magnetic control coil, one piece.
Version1.2,08-02-2012

33
APT Power Technology
Circuit Breaker Test Set

Model MVC CB Vacuum Bottle Test Set

MVC vacuum bottle tester is designed to measure roughly the vacuum degree of vacuum
arc extinguish chamber, specially suit for application at sub-station.

Product Features:
R
Sampling ionized charge, test vacuum degree with real value tested. That’s mean, one
bottle qualified or not, judged by instrument
R
Samples for 2 times so as to deduct the leakage current generated due to environmental
factors.
R
The testing process is automated.
R
judge a vacuum arc extinguish chamber leakage or not
R
Input protective circuit
R
Small-size, light-weight and easy to operate.

Specifications
Range: 1×10-5 ~6×10-1Pa,
v
v
Accuracy: within 1×10-4~1×10-1 Pa, the error<10%
v
Resolution : 10-5Pa
v
Output voltage: maximum30KV
v
Environmental temperature: 0℃~55℃.
Relative humidity <85%RH
v
v
Input:AC220±l0%, 50Hz
v
Demensions:360×310×300mm (Instrument)
v
Net Weight :6Kg (Instrument)

Order Infor mation


Item Art. No.
MVC 1 piece
Included Accessories:
œ Power input cable, Signal cable , each piece
œ Grounding cable, one piece

Version1.2,08-02-2009

34
APT Power Technology
CT Test Sets

High Accuracy CT Site Calibrating Test Sets

Test Sets Composed of:


High Accuracy CT site Calibrating Test Sets are composed of seven items as below:
ªInstrument Transformer Tester, Model ITC-C,
ªStandard reference CT, Model HL-62CS
ªCurrent load box ,model FY-96, two piece, 1A one piece, 5A one piece
ªCurrent Injection, model SL-7
ªTest console,model TC-20
ªCurrent cable set
Software is simple, used for upload data to computer.

Description:
The test set used for CT site calibration at power frequency state. The tested CT accuracy
can reach up to 0.02S.
The test method apply for IEC60185

Product Features:
R
Adopting differential measurement principle for ITC-C;
R
ITC-C can be tested for CT or PT;
R
Automatic sampling at test point
R
Automatic identification of the polarity fault and the ratio mistake.

Technical Specifications:

35
APT Power Technology
CT Test Sets

Instrument Transformer Tester, Model ITC-C


v
Input: Power Frequency: 50Hz±0.5Hz, Power Voltage: 220V±5V
v
Range
² Ratio Error (%): 0.0001 ~ 200.0 resolution 0.0001
² Angle measure (°): 0.001 ~ 700.0, resolution
0.001
² Resistance measure: (Ω): 0.0001 ~ 20.0
resolution 0.0001
² Lead-time (ms): 0.0001 ~ 20.0 resolution 0.0001
v
Basic Error
² Ratio error: ΔX=±(X×2%+Y×2%)±Dx (Class 1
option)
² Angle error(º): ∆Y = (Y*2%+X*2%*34.48) ± Dy
(Class 1 option)
² “X”、“Y”——Values Displayed
² “Dx, Dy”——Quantified Error Dx=2, Dy=5
v
Working Range
² Current:(1%-149%)In (In =5A)
(5%-149%)In (In =1A)
²
Voltage:(5%-149%)Un (Un =100V,150V,100V/)3
(5%-200%)Un (Un =100V/3)
v
Working Load
Current: TO to TX<0 . 12Ω
² cosΦ= 1 . 0
²Voltage: a to x<0 . 25VA (100V)
v
Power Consumption
Less than 15VA (without micro-printer) , Less than 25VA (with micro-printer)
v Harmonic control >40db
Polarity Check / Indication
v
Standard reference CT , Model HL-62CS
v Rated load : 5VA,1VA PF=1.0
v Be allowed to wok long time at rated current ,the wire
must be through the core if the current is over 150A.
v Standard current ratio:
Primary:
²
5,7.5,10,15,20,25,30,40,50,60,75,80,100,120,150,
160,200,250,300,315,400,
²
500,600,630,750,800,1000,1200,1250,1500,160,2
000,2500,3000,3150,4000,5000A
Secondary:5,1A
²
Accuracy class:0.02S
v
v
Temperature: 5°C ~ 40°C,Humidity: <80%

36
APT Power Technology
CT Test Sets

Test control , model TC20 :


v Capacity: 20kVA+500VA (tiny adjusting)
v Input voltage: AC 220V±10% 50Hz±1
Output voltage: AC 0~250 V
v
v
Input current: 100A
Ambient Temperature: -20℃ to 50℃
v
v
Meter accuracy class:1.0
v
Timing range:0-999S
Primary Current Injector , model SL-7:
vRated capacity:20KVA
Input voltage : 0~250V
v
Output current: 0~5000A
v
Surface temperature rise: <75 ℃
v
No-load consumption;<2 %
v
v
Continuous working at full-load: 5min
v
Intermittent working time: 15min
Current Load Box , model FY - 96:
vPower source frequency: 50Hz
vRated capacity :80VA or 60VA
vSecondary current:5A or 1A
vMeasurement range:5%-120%
vPower factor:0.8,1
vAccuracy class: ±3%
vTest voltage:2KV
vTemperature: 5°C ~ 40°C
Humidity: <80%(25℃)
v
v
Altitude :< 2500m

Version1.2,12-02-2011

37
APT Power Technology
CT Test Sets

Model CT120P CT Analyzer

Description:
CT120P CT analyzer is designed to test all kinds of protection CTs and PTs at factory or
jobsite.
Test CT/PT excitation curve and 10% Error curve by 0.5 Hz low frequency method;
Test CT/PT Turns ratio, Polarity, ratio error & phase angle error by voltage method.
Can be used at CT/PT large manufacturers or sub-station with high voltage interference.

Product Features:
R
Apply with IEC60044-1 and IEC60044-6
Low frequency and voltage test ,High anti-interference
R
R
High safety, 9 Kg, Only one person can operate
R
Maximum output voltage= 180VAC(RMS) and maximum output current 36A (Peak) ,the
instrument can accomplish the test of CT whose Knee point voltage reaches 30Kv,primary
current 10000A
R
Calculate the following CT parameters automatically:
ª Knee point voltage/current, 10% (5%) error curve ,
ª ALF (accuracy limiting factor), FS (instrument security factor),
ª Vb (max. terminal voltage), Kssc (secondary short-circuit current factor),
ª Ls (saturated inductance), Lu (unsaturated inductance),
ª Kr (remanence flux), Ts (secondary time constant)
R
Simple wire connections ,most tests are based the same wire connection, such as
excitation, ratio, phase, polarity, secondary winding resistance
R
5.7 inch real color TFT, DSP, Linux OS
R
3000 groups of test data storage, the data can be transferred to PC by USB disk for
advanced analysis and producing WORD report. Data hold even power off suddenly.

Main Functions
R
Tests on excitation, measurement of ratio and polarity
R
Measurement of CT’s ratio error, phase displacement at different primary current and
various burden
R
Measurement of CT secondary winding resistance
R
Measurement of CT Secondary burden
R
Transient characteristics test and analysis of CT
R
Automatically conclude the ratings of CT
R
Measurement on CT’s parameters: knee point voltage / current, 10% (5%) error curve, the
accuracy limit factor, instrument security factor, second time constant, remanence factor,
accuracy class, saturated and unsaturated inductance

38
APT Power Technology
CT Test Sets

Specifications

Output Voltage 0~180V(RMS)


Output Current 0~12A(RMS),36A(Peak)
Voltage/Current Measurement Accuracy ±0.2%
CT/PT Turns Ratio Measurement Range 1~10000
Accuracy ±0.2%
Angle Measurement Accuracy ±5min
Resolution 0.5min
Second Winding Resistance Measurement Range 0.1~300Ω

Accuracy 0.2%±2mΩ
Resolution 0.2mΩ
AC load Measurement Range 0~300VA
Resolution 0.02VA
Accuracy 0.2%±0.2 VA
Mains Power Supply AC220V±10%, 50Hz
Environmental Conditions Operating temperature: -10℃~50℃
Relative Humidity :=90%
Dimensions (w x h x d) 340mm×300mm×150mm
Weight <9kg

Order Infor mation


CT120P, 1piece

If you want to test both measure CT, protection CT, and PT, high accuracy model
220P is available.
If you want to test at power frequency, our model 103 is available.

Version1.2,08-05-2012

39
APT Power Technology
Others

Model DF901 Automatic 10KV Capacitance & Dissipation Factor Test Set

Description:
DF901 Automatic 10KV Capacitance & Dissipation Factor Test Set is used to measure
dissipation factor (PF) and capacitance of liquid and solid insulator, such as cables,
capacitors, line transformers, generators, motors, bushings etc.

Product Features:
R
This system is suitable for both low and high voltage measurement at line frequency
R
Whole in one designed: including precision HV digital bridge, reference capacitor internal
HV tank, precision SPWM frequency power
R
High anti-Interference by variable frequency and digital filter technology, the instrument
can ensure test accuracy while Interference current is no more than 2 times of the test
current.
R
High accuracy by high precision digital bridge, digital signal process, self-calibrating and
other advanced technique together.
R
Fully Protections, including high voltage protection, input protection and grounding
protection.
R
Multi test modes support, Supports UST (Ungrounded Specimen Test) and GST (Grounded
Specimen Test),internal/external reference capacitor (CN) mode, internal/external test
voltage selections, it can satisfy all normal dissipation factor test and HV dissipation factor
test (more than 10kV, it need an external CN which has more higher voltage level).
R
Fully automatic operation. When test start , it rises the test HV from zero to set value
smoothly, then measures data, and then falls down the output voltage to zero, and then puts
to display. If auto-print is selected, the results are printed out.
R
LCD display operation schedule and test values
External HV & reference capacitor is available
R
R
Can work together with Personal computer by
RS232
R
Suit at site or lab, for example, oil dissipation
test.

Specifications
v
PF
²Range:0-100%,auto-distinguish of
capacitance, resistance or inductance.
²
Accuracy:±(reading×1%+1pF),subject to Interference current less than 2
²
times of the test current
²
Resolution:0.001%
²
Capacitance

40
APT Power Technology
Others

²
Range: Internal HV 3pF~60000pF / 10kV,60pF~1uF/0.5kV
²
External HV 3pF~1.5uF/10kV, 60pF~30uF/0.5kV
² Accuracy: ±(reading×1%+1pF)
² Resolution:0.001 pF , 4 digital display
v
Test Current
² Range:10μA~1A
² Internal HV:0.5-10KV,adjust continuously, ±( reading×1.5%+10V) , Max. current
output:200mA
² External HV
Positive connection, Max. test current:1A,power frequency or 40-70Hz
Negative connection, Max. test current:1A,power frequency or 40-70Hz
v
Test Frequency
² 45,50,55,60,65Hz,single Frequency;
² 45/55Hz,55/65Hz,47.5/52.5Hz,auto double frequency
² Accuracy:+-0.01Hz
v
Measure time: about 30 seconds, subject to different connections
v
CVT self-excitation measure: output voltage:3-50V,output current:3-30A
CVT turns ratio test:range:10-99999,accuracy: ±reading×1%
v
Phase measure:range:0-359.9°, accuracy: ±0.1°
v
v
Data Output
² Interface;RS232
² Display: LCD
² Micro-printer
Working Temperature: -10℃~50℃
v
v
RH<90%
v
Power Input:180V-270Vac,50/60Hz,powered by Grid or generator
v
Size:440X350X380mm
v
Net Weight:30Kg

Order Infor mation


Item Art. No.
DF901
œ Df901, I piece
œ
Optional for external HV Tank and reference capacitor, for example, test transformer or
resonance test set

Version1.2,08-05-2012

41
APT Power Technology
Others

Model LRM911 Low Resistance Ohmmeter

Application:
The instrument is one of Digital Low Resistance Ohmmeter, can be used for following
applications
R Test winding resistance of motor and transformer
R Test conductor resistance of cable
R Test contact resistance of switches and socket
R Also can be used for constant current source,1A,100mA and 10mA,accuracy±3%

Product Features:
v
31/2 LCD digital display, 5 ranges
v
Adopting “four terminals” test method, eliminate errors which result from contact
resistance and lead resistance.
v
High repeatable
v
OVP Protection
v
Comply with IEC61010-1:1990
v
Powered by AC or battery( DC 12V,2.0AH)

Technical Specifications:
ª
Test current ,test range, accuracy and resolution
Test current Test range Resolution Max. Error
2~20mΩ 10μΩ
1A
20~200mΩ 0.1mΩ ±(3%+1dig)

0.2~2Ω 1mΩ Within the


100mA
2~20Ω 10mΩ range of 0.01~200Ω

10mA 20~200Ω 0.1Ω

ª
Input, AC 220V±22V,50Hz±2 Hz or By Lead-acid battery, 12V 2.0Ah
ª
Max. power consumption:3W
ª
Withstand Test: AC 1.5kV 50Hz 1min
Working temperature: 0 ° C to 40 ° C, Relative humidity: ≤ 85%, no dew
ª
ª
Size :280mm×280mm×75mm,Weight: 2.8 Kg

Order Infor mation


Item Art. No.
LRM911 1 set
Version1.3,09-01-2011

42
APT Power Technology
Others

Model SGC-03T Switchgear Local Controller

Descriptions
Model SGC- 03T is one smart device specially
designed for 3~ 35KV indoor switchgear status
indication, alarm and temperature & humidity
control.
Since all kind of switchgear status indications,
language alarming and T/ H automatic control
are integrated into one small device, therefore,
it is much great convenient for operator.
After 10 years development, switchgear local
controller is becoming popular device for
switchgear in China.
Model SGC- 03T apply for many kinds of
switchgear, for example, handcart switchgear,
fixed switchgear.

Product Functions in Details:


R CB status indication
ª CB Open or Close, Dry contact input
ª CB Closing, CB normal open contact close, red simulate bar lighting
ª CB Opening, CB normal close contact open, green simulate bar lighting
R CB Position Indication
ª While CB Run contact is in close position, Prompt CB in running position
ª While CB Test contact is in close position, Prompt CB in testing position
ª While CB handcart is in position between run and test, Luminous tube is off
R Earthing Switch Position Indication
Dry contact input close, prompt earthing switch close; Dry contact input open,
prompt earthing switch open;
R CB Spring status indication
While the spring of CB action device is stretched, prompt CB spring is in open
status.
R HV Energized Indication
Indicating A,B,C which one or all energized.
R Language alarming
ª While CB is positioned between run and test position, CB is in close position
also. The device will prompt operator to open CB by voice”Please open CB”
ª While CB is positioned between run and test position or run position, if
earthing switch is close. Then “please open earthing switch” will be warned
ª Even two wrong situation happen, then operator will be reminded ,“Please open
CB,Please open earthing switch”
R Temperature & humidity display and Control
ª Model SGC-03T has two way T/H controller inside. Start up heater while
RH≥90% , Stop heating while RH≤75%.
ª Stop heating anyway if the temperature ≥40℃;
ª While he temperature ≥ 50℃ ;Overheating light alarming or fan started for
ventilation.
R Energized CB O/F times recorded

43
APT Power Technology
Others

R
Operation Buttons on Model CGC-03T
ª O/C change-over switch
ª Local, remote control change over switch
ª Spring stretched change over switch
ª Lighting change over switch

Specifications
v
Power Input : 220Vac/dc
Ambient temperature: - 10℃ ~65℃, RH≤95%
v
v
Withstand Level≥ 2000Vac,Insulation Level≥100MΩ
v
Two way T/H controller
v
Two way loads output for heater, or fan or overheating alarm
v
RS485,MODBUS communication protocol, 103 communication protocol.
v
Open hole size on CB panel: 220mm×165mm
v
EMC, apply for IEC255- 22
v
Design life:30 years, Guarantee life: 10 years

Order Infor mation


Item Art. No.
SGC-03T, 1 piece
Included Accessories:
œ T/H sensor with its leads, 2 piece
œ Normal lend length: 5 meter, extension for customer order

Version1.2,08-02-2009

44

You might also like