Professional Documents
Culture Documents
⬜ A hub uses the hardware address in the frame to forward it to the hosts on the VLAN that
corresponds to that address.
☑ Switches use the hardware address in the frame to send it only to the port where the
device is located.
⬜ A switch uses the logical addresses in a packet to send it through the correct port to all
VLANs defined on that port.
2. Which of the following statements are true about bridges? (Select two)
⬜ Bridges connect two network segments with the same network address.
3. Which of the following best describe how a switch functions? (Select two)
⬜ It connects multiple network segments and forwards packets to the appropriate segment.
https://www.surveygizmo.com/s3/4747216/CCNA-Practice-Quiz-200-120-Quiz-1 1/7
4/14/2019 CCNA Practice Quiz: 200-120 Quiz 1
4. Which of the following are general advantages of using routers on your network?
(Select three)
☑ Routers provide more features, such as flow control, error detection, and congestion
control, than switches or bridges.
⬜ A switch reads the IP address in a packet and makes forwarding decisions based on that
address.
⬜ A switch reads the MAC address in a frame and makes forwarding decisions based on
that address.
⬜ The collision domain on a switch is all devices connected to a single switch port.
https://www.surveygizmo.com/s3/4747216/CCNA-Practice-Quiz-200-120-Quiz-1 2/7
4/14/2019 CCNA Practice Quiz: 200-120 Quiz 1
8. You have been put in charge of connecting two company networks that were previously
separated. You need to connect a 100BaseTx Ethernet network with an older token ring
network. Most traffic will be localized within each network, with only a little traffic crossing
between networks. Both networks are using the TCP/IP protocol suite. Which connectivity
device would be the best choice in this situation?
⚪ Bridge
⚪ Router
⚪ Gateway
⚪ Repeater
⚪ Switch
⚪ Hub
⚪ Router
⚪ Active hub
⚪ Switch
⚪ Bridge
10. You manage a small LAN for a branch office. The branch office has six file servers. You
want to use full-duplex Ethernet and offer guaranteed bandwidth to each server. How should
you design the network?
⚪ Divide the network using a bridge. Place the six servers on one side of the bridge, with all
client devices on the other side.
⚪ Connect all network devices to a switch. On one switch port, connect a hub. Connect all
six servers to this hub.
⚪ Divide the network using a router. Place the six servers on one side of the router, with all
client devices on the other side.
⚪ Connect all network devices to a switch. Connect each server to its own switch port.
11. You have a small network with two switches, SwitchA and SwitchB. Each switch has three
client computers connected. WrkA 1, WrkA 2, and WrkA 3 are connected to SwitchA using
https://www.surveygizmo.com/s3/4747216/CCNA-Practice-Quiz-200-120-Quiz-1 3/7
4/14/2019 CCNA Practice Quiz: 200-120 Quiz 1
client computers connected. WrkA_1, WrkA_2, and WrkA_3 are connected to SwitchA using
their own subnet, while WrkB_4, WrkB_5, and WrkB_6 are connected to SwitchB using a
different subnet. You need to connect SwitchA and SwitchB so that workstations connected to
SwitchA can communicate with workstations connected to SwitchB. Which should you do?
⚪ Connect SwitchA and SwitchB to a router using a straight-through cable on each side.
⚪ Connect SwitchA and SwitchB to a bridge using a crossover cable on each side.
⚪ Connect SwitchA and SwitchB with a bridge and a straight-through cable on each side.
12. The following items describe the functions performed at various OSI model layers.
Which of the following correctly identifies the layers that perform each of the
functions listed here?
⚪ If a router does not know a destination device's MAC address, it sends an ARP broadcast
containing the IP address and requesting the MAC address.
⚪ If a router does not know a destination device's IP address, it sends an ARP broadcast
containing the MAC address and requesting the IP address.
⚪ If a router knows the MAC and IP address of a destination host, it sends an ARP request
to update the other routers' route tables.
⚪ ARP does not play any role in the routing process. Switches use ARP to map IP
addresses to MAC addresses in collision domains.
https://www.surveygizmo.com/s3/4747216/CCNA-Practice-Quiz-200-120-Quiz-1 4/7
4/14/2019 CCNA Practice Quiz: 200-120 Quiz 1
14. Which of the following are functions of the MAC sublayer in the OSI model? (Select two)
15. The following names are given to data at various stages in the encapsulation
process.
Packets
Bits
Segments
Frames
16. Which of the following methods helps to detect lost packets? (Select two)
⬜ Flow control
⬜ Sequencing
⬜ CRC
⬜ Acknowledgements
⬜ Buffering
https://www.surveygizmo.com/s3/4747216/CCNA-Practice-Quiz-200-120-Quiz-1 5/7
4/14/2019 CCNA Practice Quiz: 200-120 Quiz 1
18. Workstation2 needs to send data to Workstation3. It sends out an ARP request for the
address of the default gateway. Which of the following are true of this request? (Select two)
⬜ The switch sends the ARP request to Workstation1 and the router.
⬜ The switch, the router, and Workstation1 will each respond with their own IP address.
19. A client computer starts to download some files from an FTP server named FTPSrv1. While
the first download is in progress, the user opens a second instance of the FTP program and
initiates a second download. What does the server and the client use to keep each download
separate?
⚪ Session ID
⚪ IP Address
⚪ Sequence numbers
20. An Internet server has a single network interface that has been assigned an IP address.
The server is running both the FTP and HTTP services. A client computer initiates a session
with the HTTP server. How is the HTTP request from the client routed to the correct service
running on the server?
⚪ Session ID
⚪ IP address
⚪ Sequence number
https://www.surveygizmo.com/s3/4747216/CCNA-Practice-Quiz-200-120-Quiz-1 6/7
4/14/2019 CCNA Practice Quiz: 200-120 Quiz 1
Next
0%
https://www.surveygizmo.com/s3/4747216/CCNA-Practice-Quiz-200-120-Quiz-1 7/7