Professional Documents
Culture Documents
COMPONENT TECHNICAL
MANUAL
Front-Wheel Drive Axles 730, 733,
740, 745 and 750
CTM4820 01JUL03 (ENGLISCH)
This manual is written for an experienced technician. listing in the introduction identifies
Essential tools required in performing certain service product-model/component type-model relationship. See
work are identified in this manual and are the machine technical manual for information on
recommended for use. component removal and installation, and gaining
access to the components.
Live with safety: Read the safety messages in the
introduction of this manual and the cautions presented Component Technical Manuals are concise service
throughout the text of the manual. guides for specific components. Component Technical
Manuals are written as stand-alone manuals covering
multiple machine applications.
This is the safety-alert symbol. When you see this
symbol on the machine or in this manual, be alert to
Fundamental service information is available from
the potential for personal injury.
other sources covering basic theory of operation,
fundamentals of troubleshooting, general maintenance,
Use this Component Technical Manual in conjunction
and basic type of failures and their causes.
with the machine Technical Manual. An application
LX24603,0000299 –19–14NOV01–1/1
General Information
• 700 Series
730, 733, 740, 745 and 750.
LX24603,0000303 –19–01JUN03–1/1
–UN–13AUG03
LX1031381
Standard 730
–UN–13AUG03
LX1031382
LX24603,00002EE –19–01JUN03–1/3
Type plate
–UN–22AUG02
left-hand side of the axle housing.
LX1029076
A—Axle type/design
B—Axle serial number
C—Tractor model
D—Ratio
LX24603,00002EE –19–01JUN03–2/3
Axle options
Tractors (not for North America) 730 733 740 745 750
6020 X
6120 and 6220 Xa
6320 and 6420 X Xb, a, c, d
6420S Xa, c, d
6520 and 6620 Xa, c, d
6820 Xa, c, d
6920 and 6920S Xa, c, d
6215 X
6515 X
SE tractors: 6020, 6120, 6220, 6320 and 6420 X
SE tractors: 6520 and 6620 X
LX24603,00002EE –19–01JUN03–3/3
INDX
Page Page
Group 00—Safety Information Check and Adjust Tread (Basic Adjustment) . . . . 05-16
Recognize Safety Information . . . . . . . . . . . . . . . . 00-1 Check and Adjust Toe-In. . . . . . . . . . . . . . . . . . . 05-18
“Important” - Information . . . . . . . . . . . . . . . . . . . . 00-1 Check and Adjust Steering Angle . . . . . . . . . . . . 05-20
“Note” - Information . . . . . . . . . . . . . . . . . . . . . . . . 00-1
Prevent Machine Runaway . . . . . . . . . . . . . . . . . . 00-1 Group 10—Planetary Drive and Wheel Hub
Handle Fluids Safely—Avoid Fires . . . . . . . . . . . . 00-2 Special or Essential Tools . . . . . . . . . . . . . . . . . . . 10-1
Prepare for Emergencies. . . . . . . . . . . . . . . . . . . . 00-2 Other Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Avoid High-Pressure Fluids . . . . . . . . . . . . . . . . . . 00-3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
Remove Paint Before Welding or Heating . . . . . . . 00-4 Planetary Drive and Wheel Hub -
Avoid Heating Near Pressurized Fluid Lines . . . . . 00-4 Sectional View (Without Multi-Disk Brake) . . . . . 10-4
Work In Ventilated Area . . . . . . . . . . . . . . . . . . . . 00-5 Planetary Drive, Multi-Disk Brake and
Wear Protective Clothing. . . . . . . . . . . . . . . . . . . . 00-5 Wheel Hub - Sectional View . . . . . . . . . . . . . . . 10-6
Practice Safe Maintenance . . . . . . . . . . . . . . . . . . 00-6 Planetary Drive - Exploded View (Without
Park Machine Safely . . . . . . . . . . . . . . . . . . . . . . . 00-6 Multi-Disk Brake) . . . . . . . . . . . . . . . . . . . . . . . . 10-8
Use Proper Lifting Equipment . . . . . . . . . . . . . . . . 00-7 Planetary Drive Removal (Without
Construct Dealer-Made Tools Safely . . . . . . . . . . . 00-7 Multi-Disk Brake) . . . . . . . . . . . . . . . . . . . . . . . . 10-9
Support Machine Properly . . . . . . . . . . . . . . . . . . . 00-7 Planetary Drive Reconditioning (Without
Work in Clean Area. . . . . . . . . . . . . . . . . . . . . . . . 00-8 Multi-Disk Brake) . . . . . . . . . . . . . . . . . . . . . . . 10-10
Illuminate Work Area Safely . . . . . . . . . . . . . . . . . 00-8 Planetary Drive Installation (Without
Service Machines Safely . . . . . . . . . . . . . . . . . . . . 00-8 Multi-Disk Brake) . . . . . . . . . . . . . . . . . . . . . . . 10-14
Use Proper Tools . . . . . . . . . . . . . . . . . . . . . . . . . 00-9 Planetary Drive and Multi-Disk Brake—
Service Tires Safely . . . . . . . . . . . . . . . . . . . . . . . 00-9 Exploded View. . . . . . . . . . . . . . . . . . . . . . . . . 10-16
Service Front-Wheel Drive Tractor Safely . . . . . . 00-10 Planetary Drive and Multi-Disk Brake
Dispose of Waste Properly . . . . . . . . . . . . . . . . . 00-10 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-17
Live With Safety . . . . . . . . . . . . . . . . . . . . . . . . . 00-11 Planetary Drive Reconditioning (With
Retighten Wheel Nuts . . . . . . . . . . . . . . . . . . . . . 00-11 Multi-Disk Brake) . . . . . . . . . . . . . . . . . . . . . . . 10-20
Mixing of Lubricants . . . . . . . . . . . . . . . . . . . . . . 00-11 Planetary Drive and Multi-Disk Brake
Lubricant Storage . . . . . . . . . . . . . . . . . . . . . . . . 00-12 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-23
Check Multi-Disk Brake for Leaks . . . . . . . . . . . . 10-28
Group 01—General Repair Information Planetary Drive - Fill With Oil . . . . . . . . . . . . . . . 10-29
General Safety and Repair Information . . . . . . . . . 01-1 Wheel Hub - Exploded View . . . . . . . . . . . . . . . . 10-30
Front-Wheel-Drive Axles - Torques for Bolts Remove Wheel Hub . . . . . . . . . . . . . . . . . . . . . . 10-31
and Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01-2 Recondition the Wheel Hub. . . . . . . . . . . . . . . . . 10-32
Installing the Wheel Hub . . . . . . . . . . . . . . . . . . . 10-34
Group 05—Steering Cylinder and Tie-Rods
Other Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05-1 Group 15—Knuckle Housing and Drive Shafts
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05-2 Special or Essential Tools . . . . . . . . . . . . . . . . . . . 15-1
Steering Cylinder and Tie-Rods — Other Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
Sectional View . . . . . . . . . . . . . . . . . . . . . . . . . . 05-3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4
Steering Cylinder and Tie-Rods — Knuckle Housing and Drive Shaft -
Exploded View. . . . . . . . . . . . . . . . . . . . . . . . . . 05-4 Sectional View . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
Removing the Tie Rods. . . . . . . . . . . . . . . . . . . . . 05-5 Knuckle Housing and Drive Shaft -
Remove the Steering Cylinder. . . . . . . . . . . . . . . . 05-6 Exploded View. . . . . . . . . . . . . . . . . . . . . . . . . . 15-8
Recondition the Steering Cylinder . . . . . . . . . . . . . 05-7 Remove Knuckle Housing . . . . . . . . . . . . . . . . . . . 15-9
Install the Steering Cylinder . . . . . . . . . . . . . . . . 05-12
Install the Tie-Rods . . . . . . . . . . . . . . . . . . . . . . . 05-13 Continued on next page
Page
–UN–07DEC88
Follow recommended precautions and safe operating
practices.
T81389
DX,ALERT –19–29SEP98–1/1
“Important” - Information
“Note” - Information
DX,BYPAS1 –19–29SEP98–1/1
–UN–23AUG88
Make sure machine is clean of trash, grease, and debris.
TS227
spontaneously.
DX,FLAME –19–29SEP98–1/1
–UN–23AUG88
hospital, and fire department near your telephone.
TS291
DX,FIRE2 –19–03MAR93–1/1
–UN–23AUG88
disconnecting hydraulic or other lines. Tighten all
connections before applying pressure.
X9811
and body from high pressure fluids.
DX,FLUID –19–03MAR93–1/1
–UN–23AUG88
Remove paint before heating:
TS220
wear an approved respirator before heating or welding.
• If you sand or grind paint, avoid breathing the dust.
Wear an approved respirator.
• If you use solvent or paint stripper, remove stripper with
soap and water before welding. Remove solvent or
paint stripper containers and other flammable material
from area. Allow fumes to disperse at least 15 minutes
before welding or heating.
DX,PAINT –19–24JUL02–1/1
DX,TORCH –19–03MAR93–1/1
–UN–23AUG88
If you do not have an exhaust pipe extension, open the
doors and get outside air into the area
TS220
DX,AIR –19–17FEB99–1/1
–UN–23AUG88
Wear a suitable hearing protective device such as
earmuffs or earplugs to protect against objectionable or
uncomfortable loud noises.
TS206
Operating equipment safely requires the full attention of
the operator. Do not wear radio or music headphones
while operating machine.
DX,WEAR –19–10SEP90–1/1
–UN–23AUG88
or welding on machine.
TS218
welding on machine.
DX,SERV –19–17FEB99–1/1
DX,PARK –19–04JUN90–1/1
–UN–23AUG88
TS226
DX,LIFT –19–04JUN90–1/1
–UN–01JUL97
Do not weld tools unless you have the proper equipment
and experience to perform the job.
LX1016749
DX,SAFE,TOOLS –19–10OCT97–1/1
–UN–23AUG88
Do not support the machine on cinder blocks, hollow tiles,
or props that may crumble under continuous load. Do not
work under a machine that is supported solely by a jack.
Follow recommended procedures in this manual. TS229
DX,LOWER –19–24FEB00–1/1
–UN–18OCT88
• Have the right parts on hand.
• Read all instructions thoroughly; do not attempt
shortcuts.
T6642EJ
DX,CLEAN –19–04JUN90–1/1
–UN–23AUG88
TS223
DX,LIGHT –19–04JUN90–1/1
–UN–23AUG88
Remove rings and other jewelry to prevent electrical
shorts and entanglement in moving parts.
TS228
DX,LOOSE –19–04JUN90–1/1
–UN–08NOV89
For loosening and tightening hardware, use the correct
size tools. DO NOT use U.S. measurement tools on
metric fasteners. Avoid bodily injury caused by slipping
TS779
wrenches.
DX,REPAIR –19–17FEB99–1/1
DX,RIM –19–24AUG90–1/1
–UN–06AUG94
hydraulic system pressure will engage the front driving
wheels, pulling the rear wheels off the support if front
wheels are not raised. Under these conditions, front drive
wheels can engage even with switch in disengaged
L124515
position.
LX,MFWD2 –19–01MAY91–1/1
–UN–26NOV90
Use leakproof containers when draining fluids. Do not use
food or beverage containers that may mislead someone
into drinking from them.
TS1133
Do not pour waste onto the ground, down a drain, or into
any water source.
DX,DRAIN –19–03MAR93–1/1
–19–07OCT88
TS231
DX,LIVE –19–25SEP92–1/1
–UN–03JAN95
L124516
LX,CRA05 002995 –19–21APR92–1/1
Mixing of Lubricants
In general, avoid mixing different brands or types of oil. Consult your John Deere dealer to obtain specific
Oil manufacturers blend additives in their oils to meet information and recommendations.
certain specifications and performance requirements.
DX,LUBMIX –19–18MAR96–1/1
00 Lubricant Storage
12
Your equipment can operate at top efficiency only Make certain that all containers are properly marked to
when clean lubricants are used. identify their contents.
Use clean containers to handle all lubricants. Properly dispose of all old containers and any residual
lubricant they may contain.
Whenever possible, store lubricants and containers in
an area protected from dust, moisture, and other
contamination. Store containers on their side to avoid
water and dirt accumulation.
DX,LUBST –19–18MAR96–1/1
LX24603,0000343 –19–01JUL02–1/1
DO NOT use these values if a different torque value or Make sure fasteners threads are clean and that you
tightening procedure is given for a specific application. properly start thread engagement. This will prevent
Torque values listed are for general use only. Torque them from failing when tightening.
values listed are for general use only.
Use only a torque wrench to tighten bolts and nuts.
Fasteners should be replaced with the same or higher
grade. If higher grade fasteners are used, these should
only be tightened to the strength of the original.
LX24603,0000304 –19–01JUL02–3/3
1
for North America: LOCTITE 242 (TY9370)
LX24603,00002FD –19–01JUN03–1/1
05 Specifications
2
Tie-rods, locknut
LX24603,0000305 –19–01JUN03–1/1
–UN–23JUL03
LX1032225
NOTE: 730, 733 and 740 axles have the axle housing
and steering cylinder transposed
(mirror-image).
LX24603,00002F8 –19–01JUN03–1/1
–UN–23JUL03
LX1031383
1
Only if dimension (x) is 90 mm (3.5 in.) or more.
Continued on next page LX24603,00002F9 –19–01JUN03–1/2
NOTE: 730, 733 and 740 axles have the axle housing 05
5
and steering cylinder transposed
(mirror-image).
LX24603,00002F9 –19–01JUN03–2/2
–UN–06AUG02
1. Remove self-locking nut.
LX1029079
LX24603,00002FA –19–01JUL02–1/3
–UN–06AUG02
LX1029080
LX24603,00002FA –19–01JUL02–2/3
NOTE: Install tie rods, see "Installing the Tie Rods" in this
Group.
LX1029081
–UN–06AUG02
NOTE: 730, 733 and 740 axles have the axle housing
and steering cylinder transposed (mirror-image).
LX1029082
NOTE: Remove tie-rods, see reference “Remove the
Tie-Rods” in this Group.
LX24603,00002FB –19–01JUN03–1/2
–UN–06AUG02
Install steering cylinder, see reference “Install the
Steering Cylinder” in this Group.
LX1029083
LX24603,00002FB –19–01JUN03–2/2
–UN–06AUG02
NOTE: Remove steering cylinder, see reference “Remove
the Steering Cylinder” in this Group.
LX1029084
Remove piston rod
LX24603,00002FC –19–01JUN03–1/13
–UN–06AUG02
LX1029085
LX24603,00002FC –19–01JUN03–2/13
–UN–06AUG02
LX1029086
–UN–07AUG02
LX1029088
LX24603,00002FC –19–01JUN03–4/13
–UN–07AUG02
inward.
LX1029897
c. Install wiper ring (C) with the dust lip facing
outward.
A—Grooved ring
B—Back-up ring
C—Wiper ring
–UN–07AUG02
LX1029898
–UN–20AUG02
inward.
LX1029091
d. Install wiper ring (E) with the dust lip facing
outward.
–UN–07AUG02
D—Back-up ring
E—Wiper ring
LX1029895
–UN–07AUG02
LX1029896
Continued on next page LX24603,00002FC –19–01JUN03–6/13
–UN–07AUG02
c. Install guide rings (C).
LX1029089
correct positions.
A—O-ring
B—Seal ring
C—Guide ring (2 used)
–UN–07AUG02
LX1029090
LX24603,00002FC –19–01JUN03–7/13
–UN–07AUG02
1. Install guide (A) on the piston rod.
LX1029899
LX24603,00002FC –19–01JUN03–8/13
2. With the two flat surfaces (A) that allow the rod to be
gripped with a wrench going in first, insert the piston
rod into the cylinder sleeve.
–UN–03JUL03
LX1031384
–UN–07AUG02
LX1029900
LX24603,00002FC –19–01JUN03–10/13
5. Pull piston rod (C) until guide (A) contacts snap ring
(B).
–UN–24OCT02
LX1029901
LX24603,00002FC –19–01JUN03–11/13
–UN–06AUG02
LX1029085
–UN–06AUG02
the contact surfaces of flange and cylinder sleeve.
LX1029084
8. Install steering cylinder, see reference “Install the
Steering Cylinder” in this Group.
LX24603,00002FC –19–01JUN03–13/13
–UN–06AUG02
NOTE: 730, 733 and 740 axles have the axle housing
and steering cylinder transposed (mirror-image).
LX1029083
1. Apply special grease MOLYKOTE G (L81050) to the
contact surfaces of steering cylinder and axle housing.
Specification
–UN–07AUG02
Cap screws—Torque ......................................................... 129 to 143 N•m
95 to 105 lb-ft
LX1029904
1
for North America: LOCTITE 242 (TY9370)
LX24603,00002FE –19–01JUN03–2/2
–UN–07AUG02
1. Coat approx. 3 turns of the thread on the tie-rod (see
arrow) with L41475 thread lock (LOCTITE 2431).
LX1029905
LOCTITE is a registered trademark of the Loctite Corporation
1
for North America: LOCTITE 242 (TY9370)
LX24603,00002FF –19–01JUN03–1/3
Specification
730—Torque ...................................................................... 240 to 270 N•m
177 to 199 lb-ft
733, 740, 745, 750—Torque ............................................. 360 to 400 N•m
–UN–06AUG02
Specification
730, 733—Torque ............................................................. 200 to 220 N•m
148 to 162 lb-ft
–UN–07AUG02
740, 745, 750—Torque ..................................................... 350 to 390 N•m
258 to 287 lb-ft
LX1029907
and Adjust Tread (Basic Adjustment)” in this Group.
LX24603,00002FF –19–01JUN03–3/3
05
15
–UN–24OCT02
LX1029908
Check tread basic adjustment For example:
1. Move steering cylinder piston rod to center position. Dimension (a), measured ............................... 273 mm (10.748 in.)
Dimension (b), measured ..................................... 3 mm (0.118 in.)
–UN–03JUL03
1. Loosen locknut (A) on left and right tie-rod.
LX1032226
in or out until distances A1 to A4 are equal.
Specification
730—Torque ...................................................................... 220 to 240 N•m
162 to 177 lb-ft
733, 740, 745, 750—Torque ............................................. 328 to 363 N•m
242 to 267 lb-ft
LX24603,0000300 –19–01JUN03–2/2
–UN–02JAN95
Checking toe-in
LX009841
rear from wheel rim to wheel rim.
Specification
Front-wheel drive axle—Toe-in ...................................................... 1.5 mm
0.06 in.
Adjusting toe-in 05
19
–UN–03JUL03
Specification
Front-wheel drive axle—Toe-in ...................................................... 1.5 mm
0.06 in.
LX1032226
2. Tighten locknut (A).
Specification
730—Torque ...................................................................... 220 to 240 N•m
162 to 177 lb-ft
733, 740, 745, 750—Torque ............................................. 328 to 363 N•m
242 to 267 lb-ft
LX24603,0000302 –19–01JUN03–2/2
–UN–04FEB98
NOTE: Steering angle must be the same on both sides.
LX1019515
tractor is equipped (tire size, front fenders and
implements). Dimension (C) can be found in the
relevant Operator’s Manual.
–UN–23JUL03
3. Determine dimension (x). If dimension (x) is 90 mm
(3.5 in.) or more, bushing1 (D) must be installed.
LX1031385
Specification
Locknut—Torque .......................................................................... 120 N•m
89 lb-ft
A—Adjusting screw
B—Locknut
C—Dimension
D—Bushing1
1
Available as spare part
LX24603,0000301 –19–01JUN03–1/1
KJD10279 –UN–04AUG03
LX24603,0000336 –19–01JUN03–2/3
LX001364 –UN–16MAR95
LX24603,0000336 –19–01JUN03–3/3
Other Material
1
for North America: LOCTITE 242 (TY9370)
LX24603,0000337 –19–01JUN03–1/1
10 Specifications
2
LX24603,0000338 –19–01JUN03–1/1
10
3
10 Planetary Drive and Wheel Hub - Sectional View (Without Multi-Disk Brake)
4
–UN–30JUL03
LX1032227
Sectional view (733)
1
On 730
2
On 733
10
5
–UN–30JUL03
LX1031386
Sectional view (750 without multi-disk brake)
1
On 740 and 745
2
On 750
LX24603,0000306 –19–01JUN03–2/2
–UN–30JUL03
LX1032228
Sectional view (733 with multi-disk brake)
A—Knuckle housing F—Needle bearing J—Tapered roller bearing N—Internally splined disk (2
B—Wheel hub G—Planet gear (4 used) K—Drive shaft used)
C—Snap ring H—Planetary carrier L—Brake piston O—Snap ring
D—Flange I—Seal ring M—Externally splined disk (3
E—Hollow ring gear used)
10
7
–UN–30JUL03
LX1031387
Sectional view (750 with multi-disk brake)
A—Knuckle housing F—Tapered roller bearing J—Seal ring O—Internally splined disk (2
B—Wheel hub G—Planetary gear (31 or 42 K—Tapered roller bearing used)
C—Snap ring used) L—Drive shaft P—Externally splined disk (2
D—Flange H—Tapered roller bearing M—Brake piston used)
E—Hollow ring gear I—Planetary carrier N—Externally splined disk Q—Snap ring
1
On 740 and 745
2
On 750
LX24603,0000307 –19–01JUN03–2/2
–UN–30JUL03
LX1031388
A—Snap ring C—Hollow ring gear G—Tapered roller bearing1, 2 K—O-ring
B—Flange D—Snap ring H—Cap screw (12 used) L—Screw plug
E—Tapered roller bearing1, 2 I—Planetary carrier M—Snap ring
F—Planetary gear (31 or 42 J—Fillister-head screw (2 N—Planetary gear (33 or 44
used) used) used), with needle bearing
1
On 740 and 745
2
On 750
3
On 730
4
On 733
LX24603,0000308 –19–01JUN03–1/1
–UN–09AUG02
Information” in Group 01.
LX1029913
1. Remove screw plug and drain oil.
LX24603,0000309 –19–01JUN03–1/5
–UN–09AUG02
LX1029914
LX24603,0000309 –19–01JUN03–2/5
–UN–09AUG02
LX1029915
LX24603,0000309 –19–01JUN03–3/5
LOCTITE is a registered trademark of the Loctite Corporation Continued on next page LX24603,0000309 –19–01JUN03–4/5
–UN–03JUL03
LX1031395
LX24603,0000309 –19–01JUN03–5/5
–UN–03JUL03
Information” in Group 01.
LX1031389
Brake)” in this Group.
LX24603,000030A –19–01JUN03–1/11
–UN–03JUL03
LX1031391
LX24603,000030A –19–01JUN03–3/11
–UN–03JUL03
LX1031389
LX24603,000030A –19–01JUN03–4/11
–UN–09AUG02
1. Remove the snap ring.
LX1029918
Continued on next page LX24603,000030A –19–01JUN03–5/11
–UN–09AUG02
2. Pull off planetary gear.
LX1029919
4. Clean the various parts, inspect them for wear or
damage and replace as necessary.
LX24603,000030A –19–01JUN03–6/11
–UN–20AUG02
6. Install planetary gear (B) with the writing facing
upward.
LX1030119
7. Install top tapered roller bearing (C).
LX24603,000030A –19–01JUN03–7/11
–UN–09AUG02
LX1030120
–UN–09AUG02
3. Clean the various parts, inspect them for wear or
damage and replace as necessary.
LX1030121
LX24603,000030A –19–01JUN03–9/11
–UN–09AUG02
LX1030122
LX24603,000030A –19–01JUN03–10/11
–UN–12AUG02
LX1029087
LX24603,000030A –19–01JUN03–11/11
–UN–12AUG02
Information” in Group 01.
LX1030123
NOTE: Thoroughly remove old thread lock from holes and
screws.
LX24603,000030B –19–01JUN03–1/5
–UN–12AUG02
Specification
Cap screws—Torque ............................................................. 68 to 75 N•m
50 to 55 lb-ft
LX1030124
LOCTITE is a registered trademark of the Loctite Corporation LX24603,000030B –19–01JUN03–2/5
Specification
Screws—Torque .................................................................... 40 to 50 N•m
–UN–12AUG02
30 to 36 lb-ft
LX1030127
LX24603,000030B –19–01JUN03–4/5
–UN–12AUG02
Specification
Screw plug—Torque ....................................................................... 90 N•m
66 lb-ft
LX1030128
LX24603,000030B –19–01JUN03–5/5
–UN–30JUL03
LX1031392
1
On 740 and 745
2
On 750
3
On 733
LX24603,000030C –19–01JUN03–2/2
–UN–09AUG02
Information” in Group 01.
LX1029913
1. Remove screw plug and drain oil.
LX24603,000030D –19–01JUN03–1/10
–UN–09AUG02
LX1029914
–UN–09AUG02
LX1029915
LX24603,000030D –19–01JUN03–3/10
–UN–12AUG02
LX1030133
LX24603,000030D –19–01JUN03–4/10
–UN–12AUG02
LX1030134
LX24603,000030D –19–01JUN03–5/10
–UN–12AUG02
LX1030136
LX24603,000030D –19–01JUN03–7/10
–UN–12AUG02
NOTE: Install multi-disk brake, see reference “Planetary
Drive and Multi-Disk Brake Installation” in this
Group.
LX1030137
LX24603,000030D –19–01JUN03–8/10
–UN–09AUG02
1. Take out cap screws.
LX1029916
LOCTITE is a registered trademark of the Loctite Corporation LX24603,000030D –19–01JUN03–9/10
LX24603,000030D –19–01JUN03–10/10
–UN–03JUL03
Information” in Group 01.
LX1031389
Brake Removal” in this Group.
LX24603,000030E –19–01JUN03–1/9
–UN–03JUL03
together as a matching set.
LX1031390
damage and replace as necessary.
LX24603,000030E –19–01JUN03–2/9
–UN–03JUL03
LX1031389
LX24603,000030E –19–01JUN03–4/9
–UN–09AUG02
1. Remove snap rings.
LX1029918
LX24603,000030E –19–01JUN03–5/9
–UN–09AUG02
2. Pull off planetary gear.
LX1029919
4. Clean the various parts, inspect them for wear or
damage and replace as necessary.
–UN–20AUG02
6. Install planetary gear (B) with the writing facing
upward.
LX1030119
7. Install top tapered roller bearing (C).
LX24603,000030E –19–01JUN03–7/9
–UN–09AUG02
LX1030120
LX24603,000030E –19–01JUN03–8/9
–UN–12AUG02
IMPORTANT: Thoroughly examine the sliding and
sealing surfaces of the brake piston
inside the flange.
LX24603,000030E –19–01JUN03–9/9
–UN–28OCT02
Information” in Group 01.
LX1030138
1. Coat a new O-ring (A) with a little grease, and install.
LX24603,000030F –19–01JUN03–1/11
–UN–12AUG02
NOTE: Thoroughly remove old thread lock from holes and
screws.
LX1030123
installed correctly.
LX24603,000030F –19–01JUN03–2/11
–UN–12AUG02
Specification
Screws—Torque .................................................................... 68 to 75 N•m
50 to 55 lb-ft
LX1030124
LOCTITE is a registered trademark of the Loctite Corporation Continued on next page LX24603,000030F –19–01JUN03–3/11
–UN–12AUG02
install them.
LX1030139
faces the O-rings (see drawing).
A—O-ring
B—O-ring
C—Back-up ring
D—Back-up ring
E—Brake piston
–UN–24OCT02
LX1030140
LX24603,000030F –19–01JUN03–4/11
–UN–12AUG02
carefully and evenly.
LX1030141
–UN–12AUG02
5. Coat special screw threads with LOCTITE 2431
(L41475).
LX1030142
6. Install special screws and tighten them evenly.
Specification
Special screws—Torque........................................................ 10 to 15 N•m
7.5 to 11 lb-ft
1
for North America: LOCTITE 242 (TY9370)
Continued on next page LX24603,000030F –19–01JUN03–6/11
–UN–12AUG02
Position the internally splined disks so that the
teardrop holes (C; if present) are aligned.
LX1030143
them.
–UN–30JUL03
illustration).
A—Gap
B—Hole
LX1033136
C—Teardrop hole
D—Thin, externally splined disk
E—Internally splined disk
F—Externally splined disk Disk arrangement on 733
G—Snap ring
–UN–24OCT02
LX1030240
Disk arrangement on 740, 745 and 750
LX24603,000030F –19–01JUN03–7/11
–UN–13AUG02
LX1030131
LX24603,000030F –19–01JUN03–9/11
Specification
Screws—Torque .................................................................... 40 to 50 N•m
30 to 36 lb-ft
–UN–12AUG02
LX1030127
LX24603,000030F –19–01JUN03–10/11
–UN–12AUG02
Specification
Screw plug—Torque ....................................................................... 90 N•m
66 lb-ft
LX1030128
LX24603,000030F –19–01JUN03–11/11
–UN–13AUG02
NOTE: Fill hand pump with clean transmission/hydraulic
oil.
LX1030145
1. Connect hand pump.
Specification
Brake—Test pressure.................................................................. 5000 kPa
50 bar
725 psi
Brake—Drop in pressure ....................................... 0.0 kPa over 3 minutes
0.0 bar over 3 minutes
0.0 psi over 3 minutes
LX24603,0000233 –19–01JUN03–1/1
–UN–13AUG02
IMPORTANT: Exclusively use oil types specified in
the relevant tractor Technical Manual.
Refer to "Front Wheel Drive Axle Oil"
LX1030159
and "Capacities" in Technical Manual
"Repair", Section 10, Group 05.
3. Fill with oil until the level comes up to the lower edge
of plug bore (A).
Specification
Screw plug—Torque ....................................................................... 90 N•m
66 lb-ft
LX24603,0000310 –19–01JUL02–1/1
–UN–24OCT02
LX1030146
A—Seal ring B—Tapered roller bearing C—Tapered roller bearing cup E—O-ring
cone D—Wheel hub F—Wheel bolt (81 or 102 used)
1
On 730 and 733
2
On 740, 745 and 750
LX24603,0000311 –19–01JUN03–1/1
–UN–13AUG02
NOTE: Remove planetary drive, see reference “Planetary
Drive Removal (Without Multi-Disk Brake)” or
“Planetary Drive and Multi-Disk Brake Removal” in
LX1030147
this Group.
LX24603,0000312 –19–01JUN03–1/4
–UN–13AUG02
LX1030148
LX24603,0000312 –19–01JUN03–2/4
–UN–13AUG02
LX1030149
–UN–03JUL03
LX1032217
LX24603,0000312 –19–01JUN03–4/4
–UN–13AUG02
NOTE: Remove wheel hub, see reference “Remove
Wheel Hub” in this Group.
LX1030150
1. Remove seal ring.
LX24603,0000313 –19–01JUN03–1/7
–UN–13AUG02
LX1030151
LX24603,0000313 –19–01JUN03–2/7
–UN–13AUG02
LX1030153
LX24603,0000313 –19–01JUN03–4/7
–UN–03JUL03
LX1032218
LX24603,0000313 –19–01JUN03–5/7
–UN–13AUG02
LX1030151
Continued on next page LX24603,0000313 –19–01JUN03–6/7
–UN–13AUG02
a. On 730 and 733: Evenly drive the seal ring in as far
as it will go. The seal ring is seated properly when
there is an all-round gap of approx. 6 mm (0.236
LX1030157
in.) between the special tool and the hub (see
drawing A).
b. On 740, 745 and 750: Drive the seal ring in until the
special tool is touching the hub; there should be no
gap between the tool and the hub (see drawing B).
–UN–29JUL03
LX1033154
LX24603,0000313 –19–01JUN03–7/7
–UN–13AUG02
NOTE: Before installing the wheel hub, apply a thin coat
of oil (not grease) to the lips of the seal and the
sealing surfaces of the knuckle housing.
LX1030149
1. Install wheel hub.
–UN–13AUG02
LX1030148
LX24603,0000314 –19–01JUL02–2/2
10
36
KJD10421 –UN–05AUG03
LX24603,000033A –19–01JUN03–2/11
KJD10282 –UN–29OCT02
LX24603,000033A –19–01JUN03–3/11
OTC27488 –UN–10FEB95
Handle . . . . . . . . . . . . . . . . . . . . . . . . . OTC274881
1
Part of tool kit D01045AA
LX24603,000033A –19–01JUN03–4/11
OTC27523 –UN–10FEB95
Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . OTC275231
1
Part of tool kit D01045AA
Continued on next page LX24603,000033A –19–01JUN03–5/11
1
Part of tool kit D01045AA
LX24603,000033A –19–01JUN03–6/11
KJD10422 –UN–05AUG03
LX24603,000033A –19–01JUN03–7/11
KJD10423 –UN–05AUG03
Installing the seal ring on the king pin (740, 745, 750).
LX24603,000033A –19–01JUN03–8/11
KJD10220 –UN–25MAR98
LX24603,000033A –19–01JUN03–9/11
KJD10420 –UN–05AUG03
KJD10281 –UN–28OCT02
Other Material 15
3
1
for North America: LOCTITE 242 (TY9370)
LX24603,0000345 –19–01JUN03–1/1
15 Specifications
4
LX24603,000033C –19–01JUN03–1/1
–UN–05AUG03
LX1032219
Knuckle housing, sectional view (750)
15
6
–UN–14AUG03
LX1033155
Knuckle housing, sectional view (750 with AutoTrac)
1
With AutoTrac
LX24603,0000317 –19–01JUN03–2/2
15
7
–UN–14AUG03
LX1032220
1
Only if dimension (x) is 90 mm (3.5 in.) or more.
2
With AutoTrac
LX24603,0000318 –19–01JUN03–2/2
–UN–04FEB98
NOTE: Remove wheel hub, see reference “Removing the
Wheel Hub” in Group 10.
LX1018418
1. Remove screw plug and drain oil.
LX24603,0000319 –19–01JUN03–1/8
–UN–06AUG02
LX1029079
–UN–06AUG02
LX1029080
LX24603,0000319 –19–01JUN03–3/8
–UN–04JUL03
LX1032221
LX24603,0000319 –19–01JUN03–4/8
–UN–04JUL03
LX1032222
LX24603,0000319 –19–01JUN03–5/8
6. Remove top king pin (A) with shims (B), seal ring (C)
and tapered roller bearing cone (D).
LX1033157
7. Remove bottom king pin (A) with seal ring (B) and 15
11
tapered roller bearing cone (C).
–UN–14AUG03
LX1033158
LX24603,0000319 –19–01JUN03–7/8
–UN–15AUG02
9. Recondition knuckle housing and king pin, see
reference “Recondition the Knuckle Housing and King
Pin” in this Group.
LX1030168
LX24603,0000319 –19–01JUN03–8/8
–UN–19AUG02
Information” in Group 01.
LX1030222
NOTE: Remove drive shaft, see reference “Removing the
Drive Shafts” in this Group.
–UN–19AUG02
LX1030223
LX24603,000031B –19–01JUN03–2/11
–UN–19AUG02
LX1030224
LX24603,000031B –19–01JUN03–3/11
–UN–19AUG02
LX1030223
–UN–19AUG02
to the outer side of the seal ring.
LX1030225
1
On 730 and 733
2
On 740, 745 and 750
LX24603,000031B –19–01JUN03–5/11
–UN–14AUG03
LX1032229
LX24603,000031B –19–01JUN03–6/11
–UN–14AUG03
LX1032230
–UN–19AUG02
LX1030228
LX24603,000031B –19–01JUN03–8/11
–UN–04JUL03
1
On 730 and 733
LX1032223
2
On 740, 745 and 750
LX24603,000031B –19–01JUN03–9/11
1
On 730 and 733
2
On 740, 745 and 750
–UN–14AUG03
LX1032229
LX24603,000031B –19–01JUN03–11/11
–UN–15AUG02
NOTE: Install drive shafts, see reference “Installing the
Drive Shafts” in this Group.
LX1030168
NOTE: Be careful not to damage shaft seal in axle
housing. Turn drive shaft during installation until
splines engage in differential.
–UN–14AUG03
grease.
2. Install bottom king pin (A) with seal ring (B) and
tapered roller bearing cone (C).
LX1033159
3. On the cap screws for the bottom king pin, coat the
threads with L41475 LOCTITE 2431 thread lock, then
install the screws.
Specification
730, 733—Torque ............................................................. 115 to 125 N•m
85 to 92 lb-ft
740, 745, 750—Torque ..................................................... 160 to 200 N•m
118 to 147 lb-ft
1
for North America: LOCTITE 242 (TY9370)
LX24603,000031E –19–01JUN03–2/7
–UN–14AUG03
NOTE: Coat tapered roller bearings and the knuckle pin
bearing hole with John Deere multi-purpose
grease.
5. Install top king pin (A) with shims (B) and seal ring (C).
–UN–14AUG03
LX1033135
LX24603,000031E –19–01JUN03–4/7
Specification
730, 733—Torque ............................................................. 115 to 125 N•m
85 to 92 lb-ft
–UN–19AUG02
740, 745, 750—Torque ..................................................... 160 to 200 N•m
118 to 147 lb-ft
LX1030238
LOCTITE is a registered trademark of the Loctite Corporation
1
for North America: LOCTITE 242 (TY9370)
LX24603,000031E –19–01JUN03–5/7
1
for North America: LOCTITE 242 (TY9370)
Continued on next page LX24603,000031E –19–01JUN03–6/7
15 Final assembly
18
–UN–07AUG02
Specification
730, 733—Torque ............................................................. 200 to 220 N•m
148 to 162 lb-ft
740, 745, 750—Torque ..................................................... 350 to 390 N•m
258 to 287 lb-ft
LX1029907
2. Fill axle housing with oil, see reference “Axle
Housing — Fill with Oil” in Group 20.
LX24603,000031E –19–01JUN03–7/7
15
19
–UN–04JUL03
Information” in Group 01.
LX1032233
LX24603,0000339 –19–01JUN03–1/4
–UN–04JUL03
3. Insert the top king pin.
LX1032234
LX24603,0000339 –19–01JUN03–2/4
Specification
730, 733—Torque ............................................................. 115 to 125 N•m
85 to 92 lb-ft
–UN–04JUL03
740, 745, 750—Torque ..................................................... 160 to 200 N•m
118 to 147 lb-ft
LX1032235
Specification
–UN–04JUL03
730, 733—Preload................................................................ 0.5 to 0.6 mm
0.020 to 0.024 in.
740, 745, 750—Preload ....................................................... 0.7 to 0.8 mm
0.027 to 0.031 in.
LX1033133
7. Calculate shim thickness (x).
For example:
Dimension (a), shims required to produce play ....... 2.0 mm (0.079 in.)
Dimension (b), measured axial play ........................ 0.7 mm (0.028 in.)
Dimension (c), prescribed bearing preload .............. 0.8 mm (0.031 in.)
Formula: x = a - b - c
8. Take out the king pin again and remove shims (a).
LX24603,0000339 –19–01JUN03–4/4
–UN–14AUG03
LX1033156
2. Using the illustration as a guide, take off the 3. Install components (K) to (H). 15
23
components as necessary.
4. Coat the threads of cap screws (G) with L41475
3. Clean the various parts, inspect them for wear or LOCTITE 2431 thread lock, then install the screws.
damage and replace as necessary.
Specification
730, 733—Torque ....................................................... 115 to 125 N•m
Installing the steering angle sensor
85 to 92 lb-ft
740, 745, 750—Torque............................................... 160 to 200 N•m
1. Re-assemble the components in reverse order and 118 to 147 lb-ft
comply with the following points.
5. Install connecting rod (F) correctly in the square
2. Install adapter (L) so that the two spigots sit hole in adapter (L).
correctly in the holes in the axle housing.
6. Place adapter (E) on connecting rod (F) in such a
NOTE: Cover area of king pin indicated by the arrow way that the flattened side of the hole that receives
with L81050 special grease (MOLYKOTE G). the steering angle sensor’s pivot is facing inward
towards the center of the front-wheel drive axle
NOTE: Coat the tapered roller bearing with John (see enlargement in illustration).
Deere multipurpose grease.
7. Align the steering angle sensor’s pivot (C) in
NOTE: Install seal ring (J) on the king pin, see relation to the hole in adapter (E), and install.
reference “Recondition the Knuckle Housing
and King Pin” in this Group.
1
for North America: LOCTITE 242 (TY9370)
LX24603,0000236 –19–01JUN03–2/2
–UN–15AUG02
LX1030220
LX24603,000031A –19–01JUL02–2/3
–UN–19AUG02
LX1030221
LX24603,000031A –19–01JUL02–3/3
–UN–04FEB98
NOTE: Remove drive shaft, see reference “Removing the
Drive Shafts” in this Group.
LX1018358
Disassembling the drive shaft
–UN–04FEB98
LX1018359
LX24603,000031C –19–01JUN03–2/10
–UN–04FEB98
LX1018360
LX24603,000031C –19–01JUN03–3/10
–UN–04FEB98
LX1018375
LX24603,000031C –19–01JUN03–4/10
–UN–10FEB98
LX1018377
LX24603,000031C –19–01JUN03–6/10
–UN–20AUG02
LX1030234
LX24603,000031C –19–01JUN03–7/10
–UN–20AUG02
LX1030235
LX24603,000031C –19–01JUN03–8/10
–UN–20AUG02
4. After installation, cover the area between the lips with
John Deere multipurpose grease.
LX1030236
5. Install drive shaft, see reference “Installing the Drive
Shafts” in this Group.
1
On 730 and 733
2
On 740, 745 and 750
LX24603,000031C –19–01JUN03–10/10
–UN–19AUG02
1. Apply a thin coat of oil to the lips of the seal ring in the
knuckle housing.
LX1030237
2. Install drive shaft in knuckle housing.
LX24603,000031D –19–01JUL02–1/3
–UN–15AUG02
LX1030220
–UN–15AUG02
LX1030219
LX24603,000031D –19–01JUL02–3/3
KJD10223 –UN–25MAR98
LX24603,0000340 –19–01JUN03–2/5
KJD10290 –UN–05AUG03
KJD10419 –UN–05AUG03
LX24603,0000340 –19–01JUN03–4/5
KJD10280 –UN–28OCT02
20 Other Material
2
1
for North America: LOCTITE 242 (TY9370)
LX24603,0000346 –19–01JUN03–1/1
Specifications 20
3
LX24603,0000342 –19–01JUN03–1/1
–UN–07AUG03
LX1033137
Differential, 730 and 733 without TLS
20
5
–UN–29OCT02
LX1030488
Differential, 740, 745 and 750 without TLS
20
6
–UN–07AUG03
LX1033138
Differential, 730 and 733 with TLS
20
7
–UN–24OCT02
LX1030489
Differential, 740, 745 and 750 with TLS
LX24603,000033D –19–01JUN03–4/4
–UN–05AUG03
LX1033139
Differential on 730 and 733
20
9
–UN–05AUG03
LX1033140
Differential, 740, 745 and 750
LX24603,000033E –19–01JUN03–2/2
–UN–05AUG03
LX1033141
Without TLS
NOTE: 730, 733 and 740 axles have the axle housing
and differential transposed (mirror-image).
20
11
–UN–05AUG03
LX1033142
With TLS
NOTE: 730, 733 and 740 axles have the axle housing
and differential transposed (mirror-image).
LX24603,000033F –19–01JUN03–2/2
–UN–04FEB98
NOTE: Remove tie rods and king pins, see "Removing
the Knuckle Housing" in Group 15.
LX1018418
1. Remove screw plug and drain oil.
LX24603,0000329 –19–01JUL02–1/3
–UN–20AUG02
3. Remove planetary drive, wheel hub and knuckle
housing with drive shaft.
LX1030132
LX24603,0000329 –19–01JUL02–2/3
–UN–20AUG02
in this Group.
LX1030154
LX24603,0000329 –19–01JUL02–3/3
–UN–04FEB98
NOTE: Remove axle housing, see "Removing the Axle
Housing" in this Group.
LX1018467
1. Remove and install bearing and seal rings from axle
housing yoke:
1
on axles without TLS
LX24603,000032A –19–01JUL02–1/1
–UN–20AUG02
1. Apply oil to O-ring (A) and install it.
LX1030155
LX24603,000032B –19–01JUN03–1/3
–UN–20AUG02
Specification
Cap screws—Torque ......................................................... 200 to 220 N•m
148 to 162 lb-ft
LX1030156
LOCTITE is a registered trademark of the Loctite Corporation LX24603,000032B –19–01JUN03–2/3
–UN–20AUG02
planetary drive, see "Installing the Knuckle Housing" in
Group 15.
LX1030132
05.
7. Fill with oil, see "Axle Housing - Fill with Oil" in this
Group.
LX24603,000032B –19–01JUN03–3/3
–UN–04FEB98
NOTE: Remove axle housing, see reference “Removing
the Axle Housing” in this Group.
LX1018427
Remove differential, see reference “Removing the
Differential” in this Group.
Without TLS
NOTE: Keep hex. nut for later rolling drag torque
adjustment of the bevel pinion drive shaft.
–UN–20AUG02
KJD10290 to loosen the hex. nut.
LX1030242
With TLS
LX24603,000032C –19–01JUN03–1/7
–UN–20AUG02
LX1030243
LX24603,000032C –19–01JUN03–2/7
–UN–20AUG02
LX1030245
LX24603,000032C –19–01JUN03–4/7
–UN–20AUG02
LX1030246
LX24603,000032C –19–01JUN03–5/7
–UN–20AUG02
LX1030247
LX24603,000032C –19–01JUN03–6/7
LX24603,000032C –19–01JUN03–7/7
–UN–04FEB98
NOTE: Remove bevel pinion drive shaft, see "Removing
the Bevel Pinion Drive Shaft" in this Group.
LX1018430
1. Pull the tapered roller bearing cone off the bevel pinion
drive shaft.
LX24603,000032D –19–01JUL02–1/2
–UN–04FEB98
LX1018444
LX24603,000032D –19–01JUL02–2/2
–UN–04AUG03
Bevel pinion drive shaft - cone point adjustment
LX1033160
(e.g. 147.65) or as a tolerance (e.g. -0.35) in
relation to the nominal dimension.
LX24603,000032E –19–01JUN03–1/15
–UN–04AUG03
LX1033161
LX24603,000032E –19–01JUN03–2/15
–UN–09FEB95
LX003237
Figure (a) read on the longer axle housing ....... 147.65 mm (5.813 in.)
Figure (b) read on the bevel pinion drive shaft . 117.10 mm (4.610 in.)
Measurement (c), bearing width ......................... 29.25 mm (1.152 in.)
Formula: x = a - b - c
–UN–22AUG02
x = 147.65 mm - 117.10 mm - 29.25 mm = 1.30 mm
LX1030250
In this example, total shim thickness required is 1.30
mm (0.051 in.).
Figure (a), tolerance read on the axle housing .... -0.35 mm (0.014 in.)
Figure (b) read on the bevel pinion drive shaft . 117.10 mm (4.610 in.)
Measurement (c), bearing width ......................... 29.25 mm (1.152 in.)
Dimension (d), nominal dimension taken from the table (e.g. for 750) ..
............................................................................... 148.0 mm (5.827 in.)
Formula: x = d ± a - b - c
x = 1.30 mm
(x = 0.051 in.)
–UN–20AUG02
LX1030251
LX24603,000032E –19–01JUN03–5/15
–UN–20AUG02
LX1030252
LX24603,000032E –19–01JUN03–6/15
–UN–20AUG02
LX1030253
LX24603,000032E –19–01JUN03–7/15
–UN–20AUG02
LX1030243
LX24603,000032E –19–01JUN03–9/15
–UN–20AUG02
KJD10290 to tighten the hex. nut.
Specification
Hex. nut—Torque ......................................................................... 245 N•m
180 lb-ft
LX1030255
LX24603,000032E –19–01JUN03–10/15
–UN–21AUG02
Specification
Bevel pinion drive shaft—Rolling
drag torque ............................................................................. 2 to 2.5 N•m
1.47 to 1.84 lb-ft
LX1030256
2. If the specified rolling drag torque is not achieved by
using the old shims, correct rolling drag value by
installing appropriate new shims.
–UN–20AUG02
2. Apply a thin coat of oil to the outer circumference of
the seal ring.
LX1030257
KJD102802.
1
On 730 and 733
2
On 740, 745 and 750
LX24603,000032E –19–01JUN03–12/15
–UN–20AUG02
(L81050).
LX1030258
LX24603,000032E –19–01JUN03–13/15
8. Install washer. 20
23
–UN–20AUG02
KJD10290 to tighten the hex. nut.
Specification
Hex. nut—Torque ......................................................................... 245 N•m
180 lb-ft
LX1030255
10. Install differential, see reference “Install Differential”in
this Group.
LX24603,000032E –19–01JUN03–15/15
–UN–20AUG02
NOTE: Remove axle housing, see "Removing the Axle
Housing" in this Group.
LX1030259
1. Remove differential (A).
LX24603,000032F –19–01JUL02–1/2
–UN–20AUG02
3. Remove shims behind the bearing cups.
LX1030260
–UN–20AUG02
LX1030261
LX24603,000032F –19–01JUL02–2/2
–UN–20AUG02
NOTE: Remove differential, see reference “Removing the
Differential” in this Group.
LX1030262
Disassembling the differential (730, 733)
LX24603,0000330 –19–01JUN03–1/25
–UN–14JUL03
LX1033152
LX24603,0000330 –19–01JUN03–2/25
–UN–14JUL03
LX1033143
20 5. Take off the top part of the housing together with the
26
disk pack and the drive bevel gear.
–UN–14JUL03
LX1033144
LX24603,0000330 –19–01JUN03–4/25
–UN–14JUL03
damage and replace as necessary.
LX1033145
LX24603,0000330 –19–01JUN03–5/25
–UN–04FEB98
NOTE: Lined side of thrust washer (B) must face disk
pack.
LX1018454
b. Install the thrust washer and splined disks on the
drive bevel gears.
A—Bevel gear
B—Thrust washer
C—Externally splined disk (4 used)
D—Internally splined disk (3 used)
–UN–14JUL03
LX1033146
LX24603,0000330 –19–01JUN03–7/25
–UN–14JUL03
LX1033147
LX24603,0000330 –19–01JUN03–8/25
–UN–14JUL03
LX1033148
LX24603,0000330 –19–01JUN03–9/25
–UN–14JUL03
LX1033150
LX24603,0000330 –19–01JUN03–11/25
–UN–14JUL03
LX1033143
LX24603,0000330 –19–01JUN03–12/25
–UN–14JUL03
Specification
Fillister-head screws—Torque ........................................... 104 to 128 N•m
77 to 94 lb-ft
LX1033151
1
for North America: LOCTITE 242 (TY9370)
Continued on next page LX24603,0000330 –19–01JUN03–13/25
–UN–21AUG02
LX1030479
LX24603,0000330 –19–01JUN03–14/25
–UN–20AUG02
LX1030262
LX24603,0000330 –19–01JUN03–15/25
–UN–20AUG02
LX1030263
LX24603,0000330 –19–01JUN03–16/25
20 5. Remove housing.
30
–UN–21AUG02
LX1030266
LX24603,0000330 –19–01JUN03–18/25
–UN–21AUG02
LX1030267
LX24603,0000330 –19–01JUN03–19/25
–UN–04FEB98
NOTE: Lined side of thrust washer (B) must face disk
pack.
LX1018454
b. Install the thrust washer and splined disks on the
drive bevel gears.
A—Bevel gear
B—Thrust washer
C—Externally splined disk (4 used)
D—Internally splined disk (3 used)
–UN–21AUG02
LX1030268
LX24603,0000330 –19–01JUN03–21/25
–UN–21AUG02
C—Thrust washer (4 used)
LX1030476
LX24603,0000330 –19–01JUN03–22/25
–UN–14JUL03
LX1033153
Continued on next page LX24603,0000330 –19–01JUN03–23/25
–UN–21AUG02
7. Install fillister-head screws and evenly tighten them
cross-wise.
Specification
Fillister-head screws—Torque ........................................... 104 to 128 N•m
LX1030478
77 to 94 lb-ft
1
for North America: LOCTITE 242 (TY9370)
LX24603,0000330 –19–01JUN03–24/25
–UN–21AUG02
LX1030479
LX24603,0000330 –19–01JUN03–25/25
20
33
20 Install Differential
34
–UN–06AUG03
Differential — bearing preload adjustment
LX1033162
dimension (e.g. 188 or 8) or as a tolerance (e.g.
0.2) in relation to the nominal dimension.
–UN–06AUG03
3. Place the tapered roller bearing cups onto the bearing
cones on the differential.
LX1033163
suitable device on a flat surface.
–UN–21AUG02
measurement will be incorrect.
LX1030482
6. Measure dimension (c).
Specification
Tapered roller bearing—Preload ...................................... 0.05 to 0.10 mm
0.002 to 0.004 in.
Figure (a) read on the longer axle housing ......... 188.0 mm (7.401 in.)
Figure (b) read on the shorter axle housing ............ 8.0 mm (0.315 in.)
Dimension (c) measured at differential ................ 194.0 mm (7.638 in.)
Dimension (d), prescribed bearing preload ........... 0.10 mm (0.004 in.)
Formula: x = (a + b) - c + d
–UN–22AUG02
x = (188 + 8) - 194 + 0.1 = 2.1 mm
LX1030495
In this example, total shim thickness required is 2.1
mm (0.082 in.).
Figure (a) read on the longer axle housing ............. 0.2 mm (0.008 in.)
Figure (b) read on the shorter axle housing ............ 0.2 mm (0.008 in.)
Dimension (c) measured at differential ................ 194.0 mm (7.638 in.)
Dimension (d), prescribed bearing preload ........... 0.10 mm (0.004 in.)
Dimension (e) taken from the table ..................... 187.8 mm (7.393 in.)
Dimension (f) taken from the table (e.g. for 750) .... 7.8 mm (0.307 in.)
Formula: x = (e ± a) + (f ± b) - c + d
x = 2.1 mm
(x = 0.082 in.)
LX24603,0000331 –19–01JUN03–3/8
–UN–21AUG02
10. Install tapered roller bearing cups (B).
LX1030483
–UN–21AUG02
LX1030484
LX24603,0000331 –19–01JUN03–4/8
–UN–20AUG02
LX1030155
LX24603,0000331 –19–01JUN03–6/8
13. Using the cap screws, join the halves of axle housing.
Specification
Cap screws—Torque .......................................................... 200 to 220N•m
148 to 162 lb-ft
–UN–20AUG02
LX1030156
Continued on next page LX24603,0000331 –19–01JUN03–7/8
–UN–21AUG02
2. Install a dial indicator and suitable device. Dimension
(a) 50 mm (1.968 in.).
3. Measure backlash.
LX1030485
Specification
730 and 733—Backlash ................................................... 0.27 to 0.35 mm
0.0106 to 0.0138 in.
740—Backlash.................................................................. 0.25 to 0.33 mm
0.0098 to 0.0130 in.
745 and 750—Backlash ................................................... 0.22 to 0.28 mm
0.0087 to 0.0110 in.
–UN–22AUG02
appropriate shim. Do not add or remove shims. See
"Differential - bearing preload adjustment", steps 9 and
10.
LX1030486
of the ring gear to the front side (toothed side).
• Too much backlash: Move shim from the front side
(toothed side) of the ring gear to the rear side.
–UN–22AUG02
NOTE: If differences occur, recheck all adjustments
carried out so far on bevel pinion drive shaft and
on differential.
LX1030494
7. Install axle housing, see reference “Installing the Axle
Housing” in this Group.
A—Ideal load pattern
B—Teeth distance must be decreased
C—Teeth distance must be increased
D—Decrease distance (pattern B)
E—Increase distance (pattern C)
LX24603,0000331 –19–01JUN03–8/8
–UN–21AUG02
IMPORTANT: Exclusively use oil types specified in
the relevant tractor Technical Manual.
Refer to "Front Wheel Drive Axle Oil"
LX1030487
and "Capacities" in Technical Manual
"Repair", Section 10, Group 05.
Specification
Screw plug—Torque ....................................................................... 90 N•m
66 lb-ft
3. Remove screw plug (A) and fill in oil until it is level with
lower edge of plug bore.
Specification
Screw plug—Torque ....................................................................... 90 N•m
66 lb-ft
LX24603,0000332 –19–01JUL02–1/1
20
40
LX24603,0000347 –19–01JUL02–1/1
–UN–11DEC01
LX1027668
A—Front-wheel drive clutch B—U-jointed shaft C—Front-wheel drive axle
When front wheel drive is selected on tractors compress the disk pack in the front wheel drive clutch
equipped with front wheel drive, all four wheels are and form a connection between the transmission and
driven simultaneously. This increases the tractor’s front wheel drive axle. When front wheel drive is
pulling power and reduces wheel slip. disengaged, oil flows from the solenoid valve to the
front wheel drive clutch. The Belleville springs are
Power is transmitted from the transmission to the rear compressed by the oil pressure and the disk pack is
wheels via the final drives. At the same time, power is released. There is no longer a connection between the
transmitted from the transmission via front wheel drive transmission and the front wheel drive axle. Front
clutch (A) to universal jointed shaft (B), which then wheel drive is always engaged when the engine is
drives the front wheel drive axle (C) and thus provides shut off, as the transmission pump stops pumping oil.
power directly to the front wheels.
Changing the gear pair or the tire combination enables
Front wheel drive is engaged and disengaged by an overrun of between 1.5 and 4% to be obtained at
means of a rocker switch. When front wheel drive is the front wheel drive axle. This means that the front
engaged, a solenoid valve interrupts the flow of oil to wheels turn slightly faster than the rear wheels. This
the front wheel drive clutch. Belleville springs improves the tractor’s traction.
LX24603,0000294 –19–07NOV01–1/1
–UN–10FEB95
LX003426
A—Axle housing C—Knuckle housing E—Drive shaft F—Steering cylinder
B—Differential D—Wheel hub with planetary
drive
Axle housing Located inside the differential housing are the drive
bevel gears and bevel pinions, together with two disk
Axle housing (A) consists of two or three parts which packs which permit self-locking. The differential is
are flanged together. The ends of the axle housing are designed to be self-locking. In most cases, this
shaped like forks, to which the axle knuckle housings prevents wheel spin when moving off and when the
(C) are attached. machine is in motion (e.g. due to slippery conditions).
Axle knuckle housings (C) provide the connection Drive shafts (E) transmit power from the differential to
between the axle housing and the wheel hubs (D). The the wheel hubs. The universal joint on each drive shaft
axle knuckle housings enable the axle to be steered. compensates for the different locations of the
differential and wheel hubs.
Differential
Wheel hub with planetary drive
Differential (B) is located in the center of the front
wheel drive axle. The differential allows the two front The gears of the planetary drive (D) are driven by the
wheels to turn at different speeds, e.g. when cornering. drive shaft. The planetary gears rotate around the
The differential consists of the differential housing, ring stationary hollow ring gear, taking the planetary carrier
gear and drive pinion. The drive pinion transmits power and wheel hub with them. The planetary drive reduces
from the universal jointed shaft to the differential. speed and increases torque.
200 Steering cylinder with a piston rod at both ends. The piston area is the
4
same at either end and the steering system is
The steering cylinder (F) is integrated into the axle therefore fully balanced.
housing. It consists of a cylinder sleeve and a piston
LX24603,0000348 –19–01JUL02–2/2
–UN–10FEB95
LX003427
Power flow when moving straight ahead Bevel pinions (E) do not rotate around their own axes.
The two wheels are driven with equal power and at
When the tractor is travelling straight ahead, the driven equal speed.
ring gear (D), housing (G) with bevel pinions (E), drive
bevel gears (B) and drive shafts (A) all turn at the
same speed.
200
6
–UN–10FEB95
LX003428
A—Drive shaft C—Disk pack E—Bevel pinion G—Housing
B—Drive bevel gear D—Ring gear F—Drive pinion
Power flow when cornering As a result, the left drive bevel gear and its associated
drive shaft turn twice for every one rotation of the ring
When the tractor is turning a corner, only the driven gear.
ring gear and the housing with the bevel pinions rotate
at the same speed. As the right wheel - and thus the Thus, if the drive wheels have unequal resistance
right drive bevel gear - are stationary, the bevel applied to them, the wheel with the least resistance
pinions must idle with the right drive bevel gear. As turns faster. As one wheel turns faster, the other turns
they do so, they rotate around their own axes. The left slower by the same amount.
drive bevel gear meshes with the rotating bevel
pinions. This produces an additional drive for the left
drive bevel gear, which normally turns idly with the ring
gear when the tractor is moving straight ahead.
LX24603,0000296 –19–12NOV01–2/2
–UN–23FEB95
LX003429
A—Drive bevel gear B—Disk pack C—Bevel pinion
The self-locking differential improves the driving axial forces, generated in the splines during torque
qualities of the machine when operating on rough and transfer, exert pressure on the disk packs via drive
slippery ground. The differential effect may be bevel gears (A), which can move axially along the
eliminated completely or only partially. It prevents loss drive shafts. Since the externally toothed disks engage
in performance caused by slippage at the drive with the differential housing and the internally toothed
wheels. Compared with a hand or pedal shift disks mesh with the drive bevel gears, relative
differential, the self-locking differential has the benefit movement between the drive shafts and differential
that it limits the load on the wheel drive shafts. A housing is made more difficult.
further advantage is that during actual operation, it
becomes effective immediately and automatically when The axial forces effect a load-dependent locking torque
needed, without any assistance from the operator. in the disk packs which is always in direct proportion to
the input torque, i.e. the input torque remains
The locking effect is produced by two multiple disk proportional to the output torque with a constant
packs (B) positioned symmetrically in the differential locking effect. The locking effect therefore varies to
housing. Due to reaction forces generated during the match the changes in engine torque and torque levels
transfer of the drive torque, axial forces are produced in the various gears.
on the inclined surfaces of bevel pinions (C). These
–UN–10FEB95
LX003430
A—Drive shaft C—Planetary gear (3 used) E—Wheel hub F—Knuckle housing
B—Planetary carrier D—Hollow ring gear
The planetary drive is driven by shaft (A). When the forced to rotate in the same direction as the drive
drive shaft rotates, planetary gears (C) must turn idly shaft. In this way, the front wheels receive an input at
on the teeth of stationary hollow ring gear (D). At the a lower speed but with increased torque.
same time, planetary carrier (B) and wheel hub (E) are
LX24603,0000349 –19–01JUL02–1/1
–UN–24OCT02
LX1030496
A—Planetary carrier C—Hollow ring gear F—Oil from/to brake valve I—Internally splined disk
B—Planetary gear (3 or 4 D—Disk pack G—Spring J—Drive shaft
used) E—Brake piston H—Externally splined disk
Pressure oil (F) flows from brake valve behind front and the universal jointed shaft is braked. The braking
axle brake piston (E) when brake pedals are effect is transmitted to the front wheels via planetary
depressed. Oil pressure forces the brake piston gears (B) and planetary carrier (A).
against disk pack (D) thus compressing it. A
connection is formed between the externally splined When the brake pedals are released, oil pressure is
disks (H) which are connected to the stationary hollow decreased and the springs (G) push the brake pistons
ring gear (C) and the internally splined disks (I) which to their initial position.
are connected to the universal jointed shaft (J).
LX24603,000034A –19–01JUL02–1/1
–UN–08FEB95
of tires and other components.
LX003431
2. Mark drive flange of front wheel drive axle (A) and the
flange of universal jointed shaft (B) (see arrows).
LX24603,0000295 –19–01JUL02–1/1
A D
Adjustments Differential
Bevel pinion drive shaft, cone point Bearing preload adjustment . . . . . . . . . . . . . 20-34 Indx
adjustment. . . . . . . . . . . . . . . . . . . . . . . . . 20-18 Exploded view. . . . . . . . . . . . . . . . . . . . . . . . . 20-8 1
Page Page
L R
T
O
Theory of operation
Front wheel drive . . . . . . . . . . . . . . . . . . . . . 200-2
Operation Front-wheel drive axle. . . . . . . . . . . . . . . . . . 200-3
Differential. . . . . . . . . . . . . . . . . . . . . . . . . . . 200-5 Tie rods
Multi-disk brake. . . . . . . . . . . . . . . . . . . . . . . 200-9 Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05-5
Planetary drive . . . . . . . . . . . . . . . . . . . . . . . 200-8 Tie-rods
Self-locking differential . . . . . . . . . . . . . . . . . 200-7 Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05-13
Toe-in, checking and adjusting . . . . . . . . . . . . . 05-18
Torques for bolts and nuts . . . . . . . . . . . . . . . . . 01-2
Tread
P Basic adjustment check . . . . . . . . . . . . . . . . 05-16
Toe-in, checking and adjusting . . . . . . . . . . . 05-18
Planetary drive (with multi-disk brake)
Exploded view. . . . . . . . . . . . . . . . . . . . . . . . 10-16
Fill with oil. . . . . . . . . . . . . . . . . . . . . . . . . . . 10-29
W
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-23
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 200-8
Wheel hub
Reconditioning . . . . . . . . . . . . . . . . . . . . . . . 10-20
Cross-section (with multi-disk brake). . . . . . . . 10-6
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-17
Cross-section (without multi-disk brake) . . . . . 10-4
Sectional view. . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Exploded view. . . . . . . . . . . . . . . . . . . . . . . . 10-30
Planetary drive (without multi-disk brake)
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-34
Exploded view. . . . . . . . . . . . . . . . . . . . . . . . . 10-8
Reconditioning . . . . . . . . . . . . . . . . . . . . . . . 10-32
Fill with oil. . . . . . . . . . . . . . . . . . . . . . . . . . . 10-29
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-31
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-14
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 200-8
Reconditioning . . . . . . . . . . . . . . . . . . . . . . . 10-10
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9
Sectional view. . . . . . . . . . . . . . . . . . . . . . . . . 10-4
Positive front wheel lead check . . . . . . . . . . . 200-10
Preload adjustment at knuckle pin bearings . . . 15-20