You are on page 1of 4

Vertical Two-Phase Separator Sizing (SI

Units)
Standard Calculation WS-CA-PR-008, Rev. 3, "Re-Issued for Use", 12-Feb-03
Verified: Verification of WS-CA-PR-008, Rev. 3, "Re-Issued for Use", 12-Feb-03
CLIENT PROJ No
PROJECT CALC No
SUBJECT SHEET OF

REVISION DATE BY CHECKED REVISION DATE BY CHECKED REVISION DATE BY CHECKED

Oil rate = 15661 kg/h Oil density = 805.3 kg/m3


Vapour rate = 0.0 kg/h Vapour density = 55.0 kg/m3
Water rate = 11142000 kg/h Water density = 968 kg/m3
Vapour molecular weight = 22.0 Vapour vol. rate = 0.00 m3/h
Vapour Std. Volume Rate = 0.0 std. m /hr
3
Water vol. rate = 11510.33 m3/h
Oil vol. rate = 19.45 m3/hr Mixed liquid density = 967.73 kg/m3
Vapour vol. rate (Q) = 0.000 m /s
3 Mixed liquid vol. rate (Qlm) = 3.2027 m3/s
K Factor = 0.050 m/s Mixture (inlet) density (Qm) = 967.73 kg/m3
SQRT(rL-rg/rg) = 4.07 Required Vapour area (Amin)= 0.000 m2
Max. allowable velocity (Vmax) = 0.20 m/s Diameter for vapour handlin= 0 mm
Slug capacity required = 0 m3
Manual override of diameter = 31089.6 mm Actual K =
(based on diameter used) 0.000 m/s
Diameter used = 31090 mm Vessel cross section = 759.137 m2
Holdup time for control
LAH to LAHH = 1.0 mins
LAL to LAH = 3.0 mins
LALL to LAL = 1.0 mins

Height to top tan line = 4663 mm 150 mm 0.15 x diameter or specified min

Allowance for Demister = 150 mm 150 mm


Height above inlet to Demister = 21763 mm 600 mm 600 mm min or height from inlet to T.T.L. = 0.85D+150mm

Demister (Y/N) = Y
Inlet nozzle height = 500 mm inlet nozzle ID

Height to inlet from LAHH = 9327 mm 300 mm 0.3 x diameter or specified min

Specified Min.
Height LAH to LAHH = 253 mm 150 mm specified hold up time or specified min

Height NLL to LAH = 380 mm 200 mm half specified holdup or specified min, and slug volume

Height LAL to NLL = 380 mm 200 mm half specified holdup or specified min

Height LALL to LAL = 253 mm 150 mm specified hold up time or specified min

Height BTL to LALL = 300 mm 300 mm


Total liquid height (from BTL) = 1566 mm 1000 mm

Note
Slug Volume is 0.0 % of Control Volume between NLL and LAH.

Total tan-tan height = 37969 mm TOTAL L/D Ratio = 1.2


Nozzles:
No Inlet
Inlet Device 1 Half-open Pipe Proprietry Device
Device
rmVm2 = 1000 Min. ID mm = 2003 mm
Required Velocity = 1.02 m/s Min. inlet diameter = 500 mm
Vapour Outlet Nozzle
rvVv2 = 3750 Min. ID = 0 mm
Required Velocity = 8.26 m/s Min. vap. outlet diam = 400 mm
Liquid Outlet Nozzle
Required Velocity = 1 m/s Min. ID (oil + water) = 2019.4 mm
Min. liquid outlet = 100 mm

418236170.xlsx
04/26/2019
file:///conversion/tmp/scratch/418236170.xlsx
Vertical Two-Phase Separator Sizing
(English Units)
Standard Calculation WS-CA-PR-008, Rev. 3, "Re-Issued for Use", 12-Feb-03
Verified: Verification of WS-CA-PR-008, Rev. 3, "Re-Issued for Use", 12-Feb-03

CLIENT PROJ No
PROJECT CALC No
SUBJECT SHEET OF

REVISION DATE BY CHECKED REVISION DATE BY CHECKED REVISION DATE BY CHECKED

Oil rate = 34454 lb/hr Oil density = 45.57 lb/ft3


Vapour rate = 0.00 lb/hr Vapour density = 3.4 lb/ft3
Water rate = 24512400 lb/hr Water density = 62.18 lb/ft3
Vapour molecular weight = 22.0 Vapour vol. rate = 0 ft3/h
Vapour Std. Volume Rate = 0.00 MMscfd Water vol. rate = 394227.89 ft3/h
Oil vol. rate = 756.03 ft3/h Mixed liquid density = 62.15 lb/ft3
Vapour vol. rate (Q) = 0.000 ft3/s Mixed liquid vol. rate (Qlm) = 109.7178 ft3/s
K Factor = 0.160 ft/s Mixture (inlet) density (Qm) = 62.15 lb/ft3
SQRT(rL-rg/rg) = 4.16 Required Vapour area (Amin)= 0.000 ft2
Max. allowable velocity (Vmax) = 0.67 ft/s Diameter for vapour handlin= 0.0 in.
Slug capacity required = 0 ft 3

Manual override of diameter = 1224 in. Actual K =


(based on diameter used) 0.000 ft/s
Diameter used = 1224 in. Vessel cross section = 8171.282 ft2
Holdup time for control
LAH to LAHH = 1.0 mins
LAL to LAH = 3.0 mins
LALL to LAL = 1.0 mins
Specified Min.
Height to top tan line = 183.6 in. 6 in. 0.15 x diameter or specified min

Allowance for Demister = 6 in. 6 in.


Height above inlet to Demister = 856.8 in. 24 in. 24 in. min or height from inlet to T.T.L. = 0.85D+6in.

Demister (Y/N) = Y
Inlet nozzle height = 20 in. inlet nozzle ID

Height to inlet from LAHH = 368 in. 12 in. 0.3 x diameter or specified min

Specified Min.
Height LAH to LAHH = 9.7 in. 6 in. specified hold up time or specified min

Height NLL to LAH = 14.5 in. 8 in. half specified holdup or specified min, and slug volume

Height LAL to NLL = 14.5 in. 8 in. half specified holdup or specified min

Height LALL to LAL = 9.7 in. 6 in. specified hold up time or specified min

Height BTL to LALL = 12 in. 12 in.


Total liquid height (from BTL) = 60.3 in. 40 in.

Note
Slug Volume is 0.0 % of Control Volume between NLL and LAH.

Total tan-tan height = 1494.7 in. TOTAL L/D Ratio = 1.2


Nozzles:
No Inlet
Inlet Device 1 ● Half-open Pipe Proprietry Device
Device
rmVm2 = 672 Min. ID mm = 78.22 in.
Required Velocity = 3.29 ft/s Min. inlet diameter = 20 in.
Gas Outlet Nozzle
rvVv2 = 2520 Min. ID = 0.00 in.
Required Velocity = 27.22 ft/s Min. vap. outlet diam = 16 in.
Liquid Outlet Nozzle
Required Velocity = 3.28 ft/s Min. ID (oil + water) = 78.31 in.

418236170.xlsx
Date}
file:///conversion/tmp/scratch/418236170.xlsx
Min. liquid outlet = 4 in.

418236170.xlsx
Date}
file:///conversion/tmp/scratch/418236170.xlsx
Q Total (m3/h) 11529.78
Ärea (m2) 759.137 0.1
Vel (m/h) 15.18801 0.2
Vel (m/s) 0.004219 verdadero
0.2

You might also like