VEA-501 / 401 Gas Analyzer is for measuring CO, HC and CO2 in automotive emissions by the principle of non-dividing infrared absorption. It also measures NO (Not for VEA-401) and O2 by electrochemical cell. It is an intellectual instrument with liquid crystal display and Chinese or English interface. It complies with the requirements of International Measurement Rules OIML R99 / 1998 (E) and the National Metrological Verification Regulations # JJG 688 for
VEA-501 / 401 Gas Analyzer is for measuring CO, HC and CO2 in automotive emissions by the principle of non-dividing infrared absorption. It also measures NO (Not for VEA-401) and O2 by electrochemical cell. It is an intellectual instrument with liquid crystal display and Chinese or English interface. It complies with the requirements of International Measurement Rules OIML R99 / 1998 (E) and the National Metrological Verification Regulations # JJG 688 for
VEA-501 / 401 Gas Analyzer is for measuring CO, HC and CO2 in automotive emissions by the principle of non-dividing infrared absorption. It also measures NO (Not for VEA-401) and O2 by electrochemical cell. It is an intellectual instrument with liquid crystal display and Chinese or English interface. It complies with the requirements of International Measurement Rules OIML R99 / 1998 (E) and the National Metrological Verification Regulations # JJG 688 for
Rules OIML R99/1998 (E) made by the Organization of International Measurement Law (OIML) and the National Metrological 1 Introduction Verification Regulations # JJG 688 for class-1 instruments. It is applicable for environmental VEA-501/401 Gas Analyzer is for measuring departments, vehicle inspection stations, CO, HC and CO2 in automotive emissions by automotive manufacturing factories and the principle of non-dividing infrared garages. absorption, measuring NO (Not for VEA-401) and O2 by the principle of electrochemical cell, calculating excessive air coefficient λ based on the composition of CO, CO2, HC and O2 2 Technical Specification measured. This instrument is equipped with Operation Condition gas bench with self-owned intellectual Temperature +5 to +40 property right, microprocessor is embedded. It Relative humidity 5% to 95%non-condensing is an intellectual instrument with liquid crystal Atmospheric pressure 70 kPa to 106 kPa display and Chinese or English interface. Power supply Inductive RPM (engine-speed) measuring Voltage AC110V±15% pliers, oil temperature sensor and printer are Frequency 60Hz ±1Hz optional for measuring RPM and oil Measurement Range temperature, and printing measurement HC (Hexane 0ppm to 10000ppm results. Equivalent)
PDF created with pdfFactory Pro trial version www.pdffactory.com
CO 0% to 10% ●6—Sampling probe : sample vehicle CO2 0% to 20% emissions. O2 0% to 25% NO (Not for NHA-406) 0ppm to 5000ppm 3.2 Front Panel RPM 300rpm to 8000rpm Oil Temperature 0 to +120 Resolution Fig. 3-2 shows the layout of the front panel. HC 1ppm Names and functions of all the parts on front CO 0.01% panel: CO2 0.01% 1 O2 0.01% 2 NO (Not for NHA-406) 1ppm RPM 10rpm 3 Oil Temperature 1℃ 4 Indication Error Absolute Relative 0ppm to 2000ppm ±12 ppm ±5% 5 HC 2001ppm to 10000 ppm - ±10% CO ±0.06% ±5% CO2 ±0.5% ±5% O2 ±0.1% ±5% Fig. 3-2 Layout of Front Panel NO (Not for NHA-406) ±25ppm ±4% ●1—Liquid crystal display: display menus and Others measurement data; Warm-up Time 10 minutes ●2—“S” key:corresponding to the functional Output Interface RS-232C sub-menu at the lower part of LCD, execute Outer Dimension (L)450mm(W)260mm(H)180 the corresponding operation; mm ●3—“K” key:corresponding to the functional Net Weight 7kg sub-menu at the lower part of LCD, execute the corresponding operation; ●4— “▲” key : move the cursor on LCD upward and select the required item ; corresponding to the functional sub-menu at the lower part of LCD, execute the corresponding operation; 3 Description of the Unit ●5— “▼” key : move the cursor on LCD downward and select the required item ; Composition corresponding to the functional sub-menu at the lower part of LCD, execute the As shown in Fig. 3-1 , the instrument is corresponding operation. composed of the instrument host, short tube, pre-filter, sampling pipe, sampling probe and 3.3 Rear Panel embedded micro printer (optional).
Fig. 3-3 shows the layout of the rear panel.
Names and functions of all the parts on rear panel:
Fig. 3-1 Composition of the Unit
●1—Instrument host : control measurement Calibration Gas Inlet
PDF created with pdfFactory Pro trial version www.pdffactory.com
Fig. 3-3 Layout of Rear Panel LAUNCH to any affirmation, representation, or ●1—Oil temperature signal socket: input warranty concerning LAUNCH automotive meters, signal of oil temperature sensor; except as stated herein. ●2—Mains socket and switch: the socket is for 220V AC power input, and the switch is for power on / off, with built-in 1A fuse and filter for Disclaimer mains noise; ●3—RS-232C socket:for communication with THE ABOVE WARRANTY IS IN LIEU OF ANY external computer; OTHER WARRANTY, EXPRESSED OR IMPLIED, ●4—“COM/Printing” Selector:switch between INCLUDING ANY WARRANTY OF “Printing” and “COM”. MERCHANTABILITY OR FITNESS FOR A ●5—Gas outlet:main outlet for sample gas PARTICULAR PURPOSE. after measurement; ●6—Condenser and sample gas inlet:connect outlet of pre-filter via short tube, to introduce Order Information sample gas. Condenser can lower sample gas temperature to prevent condensation in Replaceable and optional parts can be ordered sampling system; directly from your LAUNCH authorized tool supplier. ●7—RPM signal socket: input signal of RPM Your order should include the following information: measuring pliers or RPM adaptor;●8—Outlet 1. Quantity of NO sensor; 2. Part number ●9—Sensor cap: for protection of NO sensor 3. Item description and O2 sensor; ●10—Outlet of O2 sensor; ●11—Zero gas filter:filter the dust in air; Customer Service ●12—Calibration gas inlet: used as inlet of standard gas, with pressure of approx. If you have any questions on the operation of the unit, 0.02 MPa; please contact us: ●13—Water filter: separate oil, dust and water Tel: 00971-4-8832299 in sample gas, replace the internal big / small Fax: 00971-4-8832232, filter elements as required. E-mail: sales@launch-mena.ae info@launch-mena.ae
Warranty
THIS WARRANTY IS EXPRESSLY LIMITED TO
PERSONS WHO PURCHASE LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER’S BUSINESS.
LAUNCH electronic product is warranted against
defects in materials and workmanship for one year (12 months) from date of delivery to the user. This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages. Final determination of defects shall be made by LAUNCH in accordance with procedures established by LAUNCH. No agent, employee, or representative of LAUNCH has any authority to bind
PDF created with pdfFactory Pro trial version www.pdffactory.com