Professional Documents
Culture Documents
IMPORTANT! 2
The exposed edges of the stainless 3
steel grille and mesh can be very
sharp. Please handle with care.
4. Apply masking tape around the edges of the factory grille 5. Align the E&G mesh grille over the factory grille, mak- 6. Install the supplied small black plastic washers and #8-
emblem boss, making sure you protect the factory painted ing sure the studs pass through the openings in the 32 ESNA half nuts onto the upper studs and snug but
finish while aligning the overlay mesh grille. factory grille. Carefully turn the grille over and install do not completely tighten at this time.
the supplied lower mounting brackets and #8-32 ESNA
half nuts across the bottom of the grille. The center
stud will use the supplied 1.006” x .189” x .062” black
plastic washer instead of a lower mounting bracket.
8
7
7. Be advised of the location of the outer grille alignment 8. Clip the assembled grille back into the factory mounting 9. Thoroughly tape around the painted bumper opening
pins. These pins need to fit into the holes in the head points. using several layers of masking tape. Measure and mark
light assemblies for proper grille alignment. the exact center of the bumper cover opening (where
shown) using a grease pencil or marker.
10. Cut out and align the supplied template for the lower 11. Use a .125” (1/8”) drill bit to carefully drill through the 12. Align the lower grille into place and push the center
grille lower mounting hole locations against the inside marks made in the plastic bumper opening, then use four (4) lower mounting pins into the holes, starting at
edge of the painted bumper cover opening and tape it the drill bit to make a slot between the holes. This will the center pins and work your way to the sides.
in place, making sure the center is lined up with the allow for left to right adjustment. 13. Once the pins are pushed through the bumper cover,
center line marked in Step 10. Use an awl or similar press the grille tight against the factory insert and use a
pointed tool and mark the bumper cover at all mount- 1/16” drill bit to drill a pilot hole through the mounting
ing hole locations (see arrows). Untape the template, tabs across the top of the grille and install the supplied
flip it over and mark the holes on the opposite side. #6 Torx T-10 screws. DO NOT OVERTIGHTEN or you
will strip out the mounting holes.
WARRANTY INFORMATION:
E&G Classics, Inc. warrants its chrome parts and products to be free from defects in material,
workmanship or finish for Thirty-Six (36) months from the date of shipment by E&G. This war-
ranty is limited to the repair or replacement, at E&G Classics option, of the defective part or
product. To obtain performance under this warranty you must:
1.) Present your E&G unit to an authorized distributor in your area with proof of purchase.
2.) If no distributor is available, contact E&G Classics (address below) for authorization to
return unit.
3.) Returns - All unauthorized returns will be refused. Merchandise approved by E&G for
return must have been purchased within the Thirty-Six (36) months. All returns require
an authorization number obtained from E&G and the actual return must be accompanied
by the written authorization form filled out completely. All merchandise must be inspect
ed upon receipt and shortages reported within 48 hours. All merchandise must be in a
resalable condition. Merchandise must be packed carefully in the original packing. If orig-
inal packing is no longer usable, repack item(s) comparable to original manner. All returns
are subject to a 25% handling charge. Special order items are not returnable. Defective
merchandise must have an explanation of the problem. No credit will be issued unless
invoice number and date of purchase has been supplied. Manufacturer shall be sole
judge of defects in a product.
4.) UPS accounts - All returns must be prepaid. Do not send return shipments freight collect.
Once E&G has made its decision and it is a claim against our warranty policy, E&G will
credit incoming freight on damaged parts.
5.) No discontinued part or parts changed due to body style are returnable.
For Return Authorization, write or telephone: E&G Classics, Inc., 8910 McGaw Court,
14. Remove the masking tape and peel off the protective Columbia, MD 21045 (410) 381-4900 Attn.: Return Department
backing from the mesh and emblem surrounds. Use a You are responsible for inspecting all packages containing E&G Classics' parts and prod-
soft cloth and a mild solvent to remove any glue residue uct immediately upon their receipt and must file a claim with the carrier for any damage dis-
closure by such inspection and notify E&G classics in writing at the above address of any such
from the protective tape. Use glass cleaner or alcohol to damage. This warranty does not extend to any of our products which have been subject to
remove any solvent residue from the grille surround. misuse, neglect, accident or have been altered or repaired in any way. This warranty does not
cover any accidental or consequential damages for any breach of this warranty agreement.
E&G Classics shall have no responsibility for any loss of time, inconvenience, commercial loss
or consequential damage, nor shall E&G be liable for any injury or damage to persons or prop-
erty by reason of any defect in material, workmanship or finish of its parts or products. This
warranty gives you specific legal rights and you may also have other rights which may vary
from state to state.