You are on page 1of 2

Duplex Hybrid Combiner (Same-Band Combiner)

880 – 960 MHz 880 – 960 MHz


EGSM900 UMTS900

• Enables antenna and feeder sharing for two base stations in the
900 MHz frequency band

• Very low insertion loss over full EGSM/UMTS900 Tx bandwith Port 3


compared to standard hybrid combiners Port 2
Port 1 Port 6
• Double unit in one housing for XPol antennas Port 4
• Suitable for indoor or outdoor applications
• DC/AISG by-pass for DTMA supply (for UMTS paths only) Port 5

• Rx diversity ports protected against incorrectly connected Tx power

Typical Attenuation Curves


Diagram I Port 1 Port 3
Port 4 Port 6
0

Attenuation/dB
5

10
880 – 915 925 – 960
15

20

25

30

35

40

45

50
870 880 890 900 910 920 930 940 950 960 970
Frequency/MHz

Diagram II Port 1 Port 3


Port 4 Port 6
0

Attenuation/dB
0.5

1.0
880 – 915 925 – 960
1.5

2.0

2.5

Technical Data 3.0

3.5

Type No. 782 10805 4.0

4.5

Pass band 5.0


870 880 890 900 910 920 930 940 950 960 970
Rx 880 – 915 MHz Frequency/MHz
Tx 925 – 960 MHz
Diagram III Port 2 Port 3
Insertion loss Port 5 Port 6
Port 1 Port 3 / Port 4 Port 6 < 0.4 dB, typically 0.2 dB (925 – 960 MHz) – see Diagram I and II 0
Attenuation/dB

< 4.3 dB, typically 3.6 dB (880 – 915 MHz) – see Diagram I and II 5
Port 2 Port 3 / Port 5 Port 6 < 4.0 dB, typically 3.5 dB (880 – 915 MHz) – see Diagram III and IV 10
880 – 915 925 – 960
Isolation 15
Port 1 Port 2 / Port 4 Port 5 > 25 dB (880 – 915 MHz) 20
> 35 dB (925 – 960 MHz)
25
VSWR < 1.2 (880 – 915 / 925 – 960 MHz) 30

Impedance 50 Ω 35

Input power Port 1: < 250 W 40

Port 4: < 250 W 45


Subject to alteration.

Port 2: < 50 W 50
Port 5: < 50 W 870 880 890 900 910 920 930 940
Frequency/MHz
950 960 970

Intermodulation products < –160 dBc (3rd order; with 2 x 20 W)


Temperature range –40 ... +60 °C Diagram IV Port 2 Port 3
Port 5 Port 6
Connectors 7-16 female (long neck) 0
Attenuation/dB

Application Indoor or outdoor (IP 66) 0.5

DC/AISG transparency 1.0


880 – 915 925 – 960
936.3372/d

Port 1 Port 3 / Port 5 Port 6 Stop 1.5

Port 2 Port 3 / Port 4 Port 6 By-pass (max. 2500 mA) 2.0

Lightning protection 3 kA, 10/350 μs pulse 2.5

Mounting With 4 screws (max. 8 mm diameter) 3.0

Mast mounting: With additional clamp set 3.5

Weight 6.5 kg 4.0

4.5
Packing size 390 x 470 x 160 mm
5.0
Dimensions (w x h x d) 287.1 x 278.6 x 71 mm 870 880 890 900 910 920 930 940
Frequency/MHz
950 960 970

(without connectors, without mounting brackets)

www.kathrein.de 782 10805 Page 1 of 2


KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494
Duplex Hybrid Combiner (Same-Band Combiner)
880 – 960 MHz 880 – 960 MHz
EGSM900 UMTS900

Accessories (order separately)


Clamp set Clamp Set
Type No. suitable for mast
diameter of
734 360 34 – 60 mm
734 361 60 – 80 mm
734 362 80 – 100 mm
DC stop 782 10440
734 363 100 – 120 mm
734 364 120 – 140 mm
734 365 45 – 125 mm

Type No. Description 50-Ω load

782 10850 DC stop


784 10367 50-Ω load
1.5 W / indoor or outdoor

BTS BTS
UMTS900 EGSM900

Application example

Please note:
As a result of more stringent legal regulations and judgements regarding
product liability, we are obliged to point out certain risks that may arise
when products are used under extraordinary operating conditions.
Extraordinary operating conditions, such as heavy icing or exceptional dynam-
ic stress (e.g. strain caused by oscillating support structures), may result in the
Subject to alteration.

breakage of a mast mounted device or even cause it to fall to the ground.


These facts must be considered during the site planning process.
The Duplex Hybrid Combiner is designed to operate under the environmental
conditions as described in ETS 300 019-1-4 class 4.1 E and have passed
environmental tests as recommended in ETS 300 019-2-4.
The installation team must be properly qualified and also be familiar with
the relevant national safety regulations.
The details given in our data sheets have to be followed carefully when
936.3372/d

installing the antennas, filters, combiners, amplifiers and accessories.


Installation is possible in any direction (horizontally or vertically).
The limits for the coupling torque of RF connec-
tors, recommended by the connector manufactu-
rers must be obeyed.
Terminate unused inputs with a suitable 50-Ω load,
e.g. 784 10367.
Any previous datasheet issues have now become
invalid.

Page 2 of 2 782 10805 www.kathrein.de


KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494

You might also like