You are on page 1of 3

ERouting EIGRP PT Practice SBA

A few things to keep in mind while completing this activity:

1. Do not use the browser Back button or close or reload any Exam windows during the exam.
2. Do not close Packet Tracer when you are done. It will close automatically.

3. Click the Submit Assessment button to submit your work.

Introduction
In this Packet Tracer Practice Skills-based Assessment, you will: complete the configuration of a partially configured network establish connectivity to the West Region and the Internet through the use of static and dynamic routing verify connectivity

Addressing Table
Device Interface S0/0/0 EastHQ S0/0/1 S0/1/0 S0/1/1 Fa0/0 E-Branch1 Fa0/1 S0/0/0 S0/0/1 Fa0/0 E-Branch2 Fa0/1 S0/0/0 S0/0/1 EPC1 EPC2 EPC3 EPC4 NetAdmin NIC NIC NIC NIC NIC 192.168.1.66 255.255.255.192 192.168.1.65 192.168.1.2 255.255.255.192 192.168.1.1 192.168.0.1 192.168.0.129 192.168.1.250 192.168.1.245 192.168.1.1 192.168.1.65 192.168.1.254 192.168.1.246 192.168.0.2 255.255.255.128 255.255.255.128 255.255.255.252 255.255.255.252 255.255.255.192 255.255.255.192 255.255.255.252 255.255.255.252 255.255.255.128 Address Subnet Mask Default Gateway N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 192.168.0.1

Note: The password for user EXEC mode is cisco. The password for privileged EXEC mode is class.

Step 1: Configure the Device Basics.


Note: Initially, you can only access router E-Branch2 through the console connection on NetAdmin. a. Configure the following on E-Branch2: The router name is EB2. The privileged EXEC mode uses the following encrypted password: class. Enable Telnet and console line logins and use the following password: cisco. Configure the banner message-of-the-day as Authorized access only!

b. Using the Addressing Table, configure and activate all the necessary interfaces on E-Branch2. c. Configure correct host IP addressing. Configure EPC2 with the last IP address in the subnet. Configure EPC4 with the last IP address in the subnet.

Step 2: Discover the Network.


a. Explore the network to determine the IP address of the serial interface that EastHQ uses to connect to E-Branch2. b. Remotely access EastHQ.

Step 3: Configure Static and Default Routing.


a. Configure connectivity to the West Region. Configure a static route on EastHQ to the entire West Region. The West Region uses the 172.16.100.0/24 address space. Use the next-hop address argument. Configure a default route on EastHQ to send to the Internet all other traffic for destinations that are not found in the EastHQ routing table. Use the exit interface argument.

b. Verify static and default routing.

Step 4: Configure EIGRP Routing.


Configure EIGRP on EastHQ, E-Branch1, and E-Branch2. a. Use AS number 100. b. Do not advertise the network between EastHQ and the Internet. c. Do not advertise the network between EastHQ and the West Region. d. Advertise all other attached networks. e. Disable automatic summarization. f. Disable EIGRP updates out interfaces where there are no EIGRP neighbors available. g. On EastHQ, enter the one command in the EIGRP routing process that will propagate the default and static routes to E-Branch1 and E-Branch2.

Step 5: Modify the default EIGRP operation.


a. Configure the link between EastHQ and E-Branch2 so that the correct bandwidth of 384 k/s is used in EIGRP calculations. b. Configure E-Branch1 to advertise a summary route for the subnets 192.168.0.0/25 and 192.168.0.128/25 to EastHQ and E-Branch2. c. Configure E-Branch2 to advertise a summary route for the subnets 192.168.1.0/26 and 192.168.1.64/26 to EastHQ and E-Branch1.

Step 6: Verify Full Connectivity.


Although these are not scored, the following connectivity tests should be successful. Test connectivity to the West Region. Test connectivity to the Internet.

Version 1.0 Created in Packet Tracer 5.3.1.0044 and Marvel 1.0.1 All contents are Copyright 1992 - 2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

You might also like