Professional Documents
Culture Documents
Actuators
Direct
N05, N10, ML Series:
Coupled Actuator
VAV & Bypass Dampers
Unit Ventilators
Applications S03, S05 Series:
Low Torque Non-spring Return
There is a Honeywell Direct Coupled Actuator for all your HVAC applications
DCA Applications—Air Handler
(Generally Spring-return DCA)
Units (AHU)
Outdoor Face & Bypass
(OA)/Return (RA) dampers
dampers
N34 Series N20 Series N10 Series N05 Series MLXX61 MLXX74
Series Series
Declutch
Input Signal Type
•1: Standard
• 61 Floating, 24 Vac
•2: Includes declutch function
• 71 Modulating, 24 Vac
Flippable housing design (SR) Simplifies installation by allowing easy reversal of spring
return direction
Signal mode switch on cover Simplifies installation & commissioning by allowing installer N20, N34
to designate input signal and driving direction by the turn Series
of a switch.
Rated torque is minimum for life, Honeywell actuators will operate your damper at the
temperature and voltage, not best extremes, not just the nominal.
case.
Constant run time Easier to tune control loops for both floating and
proportional controls.
Stall torque overload protection Protects actuator from jammed or blocked dampers.
Integral end switches or field-addable Increases functionality. Energize auxiliary equipment such
auxiliary switches as blower or pump.
N05, N10
Integral mechanical range limits No extra parts needed. Eliminates need for accessory parts
to accomplish limited range functions. Series
Double insulated line-voltage circuits Simplifies wiring and installation. No ground needed.
Redundant position monitoring Saves time. No need to wait for actuator to “re-learn” its
position on start-up.
N20, N34
Rated torque is minimum for life, Honeywell actuators will operate your damper at the Series
temperature and voltage, not best extremes, not just the nominal.
case.
Plenum rating for all models Easier selection and stocking.
DC Brushless motor technology Torque and timing control. Improved functionality. Lower
(proportional models) noise.
Honeywell Wiring Standard Simplified wiring and installation. All actuators wire the
same for fewer wiring mistakes.
S05, S10, S20
Series
Standard Wiring
Actuator Wiring Standard…regardless of signal type!
Select 24 Vac SR 120 Vac SR 24 Vac SR 24 Vac SR 24 Vac NSR 24 Vac NSR
Drive 2-position 2-position Floating Modulating Floating Modulating
3 CW Input CW Input
4 CCW CCW
5 Feedback Feedback
• Accessories:
– Rotary-to-Linear Crankarm Kit (205830A)
– Remote Minimum Position Control (205860)
– Flexible Anti-rotation Bracket (50006427-001)
– Weather Enclosure (32003036-001)
– Water-tight Strain Relief Fittings – 10 pack (3200085-001)
Modulating or Floating – 4-20 mA Resistor Kit – 6 pack (32006306-001)
– Auxiliary Potentiometer Pack (coming soon)
– Auxiliary Switch Pack (coming soon)
N20 Series
Torque: 175 lb-in (20Nm)
Running Time: 90 sec. independent of load
Control Input: Floating and Two-position
Modulating
Overload Protection: Electronic Stall Protection (modulating)
Magnetic hysteresis clutch (floating)
Rotation: 95° (adjustable)
Shaft Diameter: 3/8”…1-1/16” (10…27mm)
Manual Override: Declutch push button
Direction of Rotation: Selectable by switch
Dimensions: 8-13/16” x 3-5/8” x 3-1/8” (223 x 92 x 80 mm)
Electrical Connection: Terminal strip with removable access cover
Built-in Auxiliary Switch: 2 x SPDT
Environment Protection: NEMA 2 / IP54
Temp Rating: -5°…140°F (-20º…60°C)
Model Voltage Control Aux. Switch
MN6120A1002 24 Vac ±15% Floating/Two-Position No
• Accessories:
– Remote Mounting Kit (50001194-001)
– Remote Minimum Position Control (205860)
– Flexible Anti-rotation Bracket (50006427-001)
– Tandem Mounting Kit (50000407-001)
– Weather Enclosure (32003036-001)
– NEMA 4 Enclosure (50005859-001)
– Water-tight Strain Relief Fittings – 10 pack (3200085-001)
– Auxiliary Switch Pack (SW2)
Zelix Expands the Portfolio
• Expands portfolio to lower torque levels
– 3 Nm & 5 Nm (27 & 44 lb-in)
• 44 lb-in DCA will replace existing, larger-sized
DCA
• 88 and 175 lb-in DCA still available
Spring Return Actuators
S20 Series S10 Series S05 Series S03 Series
Containment
Suppression Detection
42
Smoke/Fire and Smoke
Applications
Two types of damper use
1. Containment /
Compartmentalization
90% simply close to prevent
smoke or fire spread.
2. Engineered smoke control Compartmentalization
Courtesy of Greenheck
Engineered Smoke
Stairwell pressurization
Control Systems
Atria smoke extraction
Elevator shaft pressurization
Ventilated lobbies
Corridor dampers
Ceiling dampers
Shaft dampers
Duct dampers
Fire & Smoke doors
Smoke Extraction Shafts and Fans
Sandwich or building pressurization systems
What is UL-555 and UL-555S
• Standards
– UL-555 Fire Dampers
– UL-555S Smoke Dampers
• All smoke and fire/smoke dampers are UL
certified through the damper manufacture
• All new fire and smoke dampers must:
– Be tested to and pass fire and smoke
requirements for each damper assembly sold
•UL
Each size damper
Certification is on the entire damper assembly
• Each actuator
Fire and Smoke Vs. HVAC Actuators
• Fire and Smoke Actuators • HVAC Actuators
– Fast acting: 15-20 Sec. for spring – Timing
and drive timing • Spring Timing is 25 sec.
– Normally open • Drive Timing is 45 or 90 sec.
– Two-position and occasionally – Field configurable fail safe
modulating – Available in multiple control
– Spring return signals
• Designed to meet the UL-555 and – Non-spring-return and spring
UL-555S temperature return
requirements • Ambient Temperature
– 250ºF or 350ºF – Up to 140ºF
• Designed to withstand 30,000 full • Designed to operate up to 60,000
stroke cycles cycles
– Not intended for HVAC • A combination of metal and
• All metal components plastic components
Current Portfolio – Legacy Design
Spring
Torque Voltage Direction Description Number of internal Auxiliary Switch Model Number
CW External* MS4209F1007
* The 30 lb-in and 80 lb-in fast acting two position actuators are not available
with internal switches. An external switch package is available, part number
32003532-005
Current Portfolio – High Torque
Design
Spring Number of internal
Torque Voltage Direction Description Auxiliary Switch Model Number
None MS4120F1006
Note: Honeywell's Spring return Fire and Smoke actuators are designed for to pass the
UL-555 and UL-555S 350ºF requirements. They are not designed for HVAC
applications. UL-555 and UL-555S requires that all new construction fire and smoke
damper jobs have the actuator assembled and tested at the damper manufacture. A
like for like retrofit replacement or technically equal UL-555 and UL-555S approved
device is recommended.